CA NO. CWE BLY / GE(E) / 62 OF 2022-23 ADDITION / ALTERATION CUM SPL REPAIRS TO BLDG NO P-68 Div HQ UNDER GE(E) BAREILLY

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc complete all specified and directed.

Taking down stone grit on plastered surfaces on brick/stone wall including racking out joints, hacking for keys, scrubbing down with water etc including removing from site complete all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed .

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter and refixing with easing in other opening of any description exc. 2 sqm complete all as specified and directed .

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed .

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Dismantling water tanks 500 & n exc 1000 and removing to store of all retrieved material complete all as specified and directed .

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed by Engineer - in - Charge.

M & L 25 mm thick PCC 1:2:4 type B-1, using 12.5 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M & L 7 to 8mm thick glazed ceramic coloured tiles ( square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for vitrified glazed ceramic colored/ double charged / ultra-charged tiles 10 mm thick square/ rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed

M&L for vitrified glazed ceramic colored/ double charged / ultra-charged tiles 10 mm thick square/ rectangular) polished area of each tile not exceeding 0.36 sqm as in vertical surfaces such as skirting or dado set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as spd and directed.

M&L for vitrified ceramic coloured/ double charged / ultra charged tiles 10 mm thick square/ rectangular) polished area of each tile exceeding 0.42 sqm but not exceeding 1.00 in floors etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as spd and directed.

M&L for vitrified glazed coloured/ double charged / ultra charged tiles 10 mm thick square/ rectangular) polished area of each tile exceeding 0.42 sqm but not exceeding 1.00 in vertical surface etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L for vitrified ceramic exterior heavy duty out door coloured tiles 12 mm thick (Square/rectangular) polished area of each tile size not exceeding 0.36 sqm on floor set and jointed in neat cement mortar and pointed in white or coloured cement to match complete all as specified and directed.

M&L 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including form work , pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M& L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed

M&L for Machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80mm thickness, M-30 Grade, machine pressed of pattern and colour as approved by Engineer - in- Charge laid over a layer of sand cushion not less than 25mm thick set and jointed with sand in hard standing complete all as specified and directed.

M&L for PCC (1:2:4) type B1 using 20mm graded aggregate for machine pressesd precast cement concrete kerb stone including weathering, slightly rounded or chemferred angles and throating , as directed edges complete including excavavtion for kerb stone complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M& L for rendering 10mm thick in cement mortar (1:4), and 5 mm thick setting layer in CM1:3 finished even and smooth using extra cement to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed.(Note : Water proofing liquid shall be measured and paid separately)

supply Integral water proofing Liquid complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:4 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing NOTE-Colour of pvc match to that of shutter complete all as specified and directed.

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and directed.

S&F 30 mm Plain, framed ,panlled shutters(any number of panels), Ist class HW with panels of timber flat on both sides(feather edged), or of veenered particle board medium density , wood particle board with commercial face veeners. Complete all as specified and directed

M&L for 1st class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F for 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium beading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty . (g) Making good of wall surface to match with existing surface complete.

S&F Powder coated aluminium sliding windows frame with movable shutter sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :95x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading : 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S & F for aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48 mm thick,4 mm thick aluminium composite panel LDPE core with PET coating fixed with into the wall for kitchen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging , design as per site requirements basis, complete all neccessary fitting complete all as specified and directed.

M & L powder coated aluminum window/ doors grills fixing along with frame of following specification, grills with opening 69.4mm X 78.2mm grills thickness shall be of 6.4mm X 5.8mm having weight not less than 2.306 Kg/per sqm shape as ordered with frame channel of 34 X 11mm X1.7mm thick fixed with screw inside of the window complete all as specified and directed.

S & F partition wall of powder coated aluminium hollow sections members of size 63.50 mm x38mmx 1.48 mm thick with distance of vertical hollow section, 1.2mtr to 1.8 mtr height of wall having top rails ,bottom rails and middle rail of size 63.50 mm x38mm x 1.48 mm and upto middle rail wall panels shall be covered by 5 mm thick aluminium composite panel LDPE core PET coating ( both side decorative type )with aluminium clip height of middle rail shall be 1 meter from floor and remaining portion above middle rail shall be provided with 5 mm thick glass incl eaching approved designed with aluminium stiprs/beadings with rubber gasket as per existing or as provided compelte all as specified and directed.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

M&L Cement concrete in foundations, filling and mass concrete (PCC) Type D2 1:4:8 (40 mm graded aggregate) etc complete all as specified & as directed

M&L flat form work to sides of concrete foundations, footing bases of columns, raft and raft beams, sides and soffits(if any) of foundation and plinth beams and similar work, veritical or to batter complete all as specified and directed.

M&L for RCC M-25 (Desigh mix) (20mm graded stone aggregate) for foundation including rafts, footings, foundation beams, plinth beams, bases for columns, etc, complete all as specified and directed.

M&L form work to sides of pillars posts, struts piers, columns & stanchions square rectangular or polygonal rough finished surfaces in shape complete all as specified and directed.

M&L for RCC M-25 (Design mix) (20mm graded aggregate) for columns, pillars, piers, posts & struts etc complete all as specified and directed.

M&L flat form work to sides and soffits of floors or roof beams haunching, girders bressumers lintel cantilevers shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and directed.

M&L for RCC Design Mix M-25 (20mm graded aggregate) for beams cantilevers bressummers, lintels over 1.5m span etc complete all as specified and directed.

M&L,flat rough finished surfaces Form work to soffits of suspended slab such as roof slabs, floors slabs, landing & similar work not exceeding 200 mm thick (Horizontal or sloping) etc complete all as specified and directed.

M&L for RCC Design mix M-25 (20mm graded aggregate) for slab supported on walls, beams and columns in floors, roofs, landings balconies canopies, deck slab and in shelves and the like etc etc complete all as specified and directed.

M&L for form work to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in valls etc rough finished surfaces of concrete flats complete all as specified and directed.

M&F formwork to rough finished surfaces of contrete of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for RCC design mix M-25 (20mm graded aggregate) as in chajjas complete all as specified and directed.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified and directed.

As per item No. 63 but 6mm to 8mm dia

M&L for DPC to horizontal or vertical surfaces including necessary form work 25mm thick PCC (1:2:4) Type B0 (12.5mm graded aggregate on plinth beam including mixing of water proofing compound as per manufacturers instructions and necessary form work complete all as specified and directed.

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight colled rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm long mild steel sliding door bolts plate type stone enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed by Engineer-in-Charge.

S&F 1000 litres, rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F in Vitreous China table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified and directed.

S&F in repair fancy type brass chromium plated toilet paper holder complete all as specified and directed.

S&F in repairs bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified.

S&F in repair fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed.

S&F stainless steel of AE - SI 316 grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish, complete all as specified and directed.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed.

S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified and directed.

S&F in repair fancy type glass corner 300mm radius of 10mm thick glass with CP railing fixed with screws fancy type complete all as specified and directed.

S&F in repair rimless single piece wc with UF soft closed sheet cover,hinges,fixing,accesseries sets and cistern fittings size 360x675x750mm, S trap 300 mm including making good to floor complete all as specified and directed.

S & F Brass CP health faucet with 8mm Dia 1.25 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body complete all as specified and directed.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S & F PTMT alloy toilet cabinet with mirror of overall size 350 x 450mm and fixed to wall complete all as specified and directed.

S & F Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed .

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

M &L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry 3 kg/sqm for filling undulationations finished even and smooth without using extra cement complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge. (Note : Water proofing liquid shall be measured and paid separately)

Supply Integral water proofing Liquid complete all as specified and directed.

S&F Framed work as in ladders,gates,and starirs of angle or other section with gussets plates,rails,barcesetc complete ,drilled for fixing of steel sheeting or other covering to be prepared or hanging or sliding with an including either hooks and hinges or steel hanging door fittings and fastening and fixing Fe 290 gde E-165 complete all specified and directed.

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting exc 10cm and not exc 40cm girth in brick walls complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and construction fibre as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of water proofing liquid new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and directed.

M&L for dubbing coat on exposed cement concrete 10 to 20 mm cement plaster 1:4 incl micro concrete with chicken wire mess with water proofing liquid @200 ml per bag up to II nd floor roof level complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for painting of new wooden or wood based surfaces of any description exc 10 cm in width or girth when unconnected with other painting or when painted in a diferent tint and applying two coat of synthetic enamel paint over and including one coat of Pink Primer complete all as specified and directed.

M&L for preparation of painted wooden or wood based surfaces of any description exc 10 cm in width or girth when unconnected with other painting or when painted in a diferent tint and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L French polishing on surface of any description ,width or girth incl cleaning and preparing the surface incl a coat of wood filler on old work with two coats complete all as specified and directed.

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etc by skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over one coat of plaster of paris of 1mm thickness complete all as specified and directed. Note:-Application to be done through authorised applicator of manufacturer.

M&L for two coat OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1mm thickness complete all as specified and directed. Note-Application to be done through authorised applicator of manufacturer

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new surface of plastered and applying of two coat OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over 1 mm thick plaster of peris (approved by GE)prepared and sanded with electrically operated sanding machine. Application to be done through the authorised applicator of manufacturer complete all as specified and directed.

M&L for old/newplastered walls surfaces and applying two coats of cement base paint over a coat of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old/new plastered wall (For old Plastered wall- complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etc by skilled labour)and applying two coats of Dust Resistant , Anti Algal weather proof exterior/internal emulsion paints(appex) by electric sprayers over a one coat of putty of 1mm thickness complete all as specified and directed.

M &L for 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to 605x605mm GI framework for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long icluding dismantling of old ceiling board with frame complete all as specified and directed.

Providing & fixing 10mm thick plaster of paris false ceiling binding as required shape with two coats of plastic emulsion paint over a coat of primer on decorated surfaces of ceiling including 26 gauge galvanished iron sheet 'C' shaped main member @750 mm C/C cross member 'U' shaped @450 mm c/c and perimeter of 'C' shaped GI wire mesh having aperture 6.5 mm with 26 gauge wire GI wire 6mm dia or more or FI 40x4mm thick for hanging arrangement with MS suspension.fastner spaced @ 450mm c/c in both direction the 'C' member shall be made out of not less than 90mm wide GI sheet strip and side tray as required of approximate size 3.5 Mtr height as required at site complete all as specified and directed.

M & L for prelam Solid PVC Wall Lining consisting of 5mm thick coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

M & L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.

S&F in repairs, wall mounted censor urinal size 370x315x620mm with all fixing Accessories complete all as specified and directed.

S&F 12 mm thick toughned glass door with powder coated aluminium frame including neccessary locking ,handle etc with double action floor spring in each shutter complete as requirement of site with suitable height and any type of eaching designed on tougned glass , off cuts complete with finishing wall in CM 1:4 , designed approved by Engr-in Charge complete all as specified and directed.

S&F 10-12 mm thick toughned glass partition wall with or without aluminium frame/CP rolling rod with any type of etching designed on toughned glass,of cuts complete as reqmt of site with arrangement for suitable height with offcuts complete all as specified and directed.

Taking down copper/aluminum point wiring complete including fixture and fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings, holders etc and removing the items from site to store for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces to match with the existing surfaces of walls, floors etc complete all as specified and directed.

Taking down electric meter and disconnecting, removing to store for keeping in safe custody for refixing etc complete all as specified and directed.

Taking down main switch / MCB DBS including MCBS etc of any size and removing the items from site to store for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces to match with the existing surfaces of wall, floors etc complete all as specified and directed.

Taking down Geyser and disconnecting water & electric connections, removing to store for keeping in safe custody for BER Board or rehanging etc after some minor repair complete all as specified and directed.

Taking down ceiling/exhaust fan and disconnecting, removing to store for keeping in safe custody for BER Board or rehanging etc after some minor repair complete all as specified and directed.

Taking dowm submainwiring/service cable including earth wire and removing from site to store for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces to match with the existing surfaces of walls, floors complete all as specified and directed.

M & L for point wiring for modular fittings with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor FRLS 1100 Volts grade cable ( red colour cable to be used for live connection and black colour cable to be used for neutral connection ) controlled by one way switch drawn through and including non metallic rigid PVC concealed conduit with all accessories and 1.5 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated ( green colour ) as continuity earth wire connected to common earth dolly and with metal flush box for mounting of modular fittings and cover plate( Metal box, inner & outer cover plate etc shall be measured and paid separately under respective items) incl cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for one light/fan/exhaust fan/bell point controlled by one modular switch/bell push complete all as specified and directed.

All as per item No 128 above but one 3 pinModular socket oultel 6 Amp on the same board with other switch.

All as per item No 128 above but one 3 pin Modular socket outlet 6 Amp independent.

All as per item No 128 above but for one light point controlled by two, 2-way 6Amps Modular switch.

All as per item No 128 above but one 3 pin Modular socket outlet 16 Amps independent with 2.5 Sqmm PVC insulated sheathed cable and 2.5Sqmm cable for earth wire.

S&F Modular Cover plate with frame 1 Module complete all as specified & directed.

S&F Modular Cover plates with frame 2Module complete all as specified & directed.

S&F Modular Cover plates with frame 3 Module complete all as specified & directed.

S&F Modular Cover plates with frame 4 Module complete all as specified & directed.

S&F Modular Cover plates with frame 6 Module complete all as specified & directed.

S&F Modular Cover plates with frame 8 Module complete all as specified & directed.

S&F Modular metal flush box 1/2 Module complete all as specified & directed.

S&F Modular metal flush box 3 Module complete all as specified & directed.

S&F Modular metal flush box 4 Module complete all as specified & directed.

S&F Modular metal flush box 6 Module complete all as specified & directed.

S&F Modular metal flush box 8 Module complete all as specified & directed.

S&F Modular switch piano flush type single pole one way 6 Amps complete all as specified and directed.

S&Fmodular switch piano flush type single pole two way 5 Amp. complete all as specified and directed.

S&F Modular Switch Piano flush type single pole one way 16 Amps.complete all as specified and directed.

S&F Bell Modular push flush type 5 Amp complete all as specified and directed.

S&F Modular Socket outlet 2 in 1, 3 pin 6 Amp flush type complete all as specified and directed.

S&F Modular socket outlet 2 in 1, 3 pin 5Amp and 16 Amp complete all as specified and directed.

S&F Bell AC 230 Volt single pole Ding Dong complete all as specified and directed.

S&F Lamp holder ( batten/angle ) PVC/Polycarbonate type with back plate for batten/angle fittings complete all as specified and directed.

S&F ceiling roze, 3 terminals, PVC polycarbonate isolated body complete all as specified and directed..

S & F Lamp LED heat sink white with polycarbonate diffuser, B-22 base cap, retrofit type, 220/230 Volts,7/9 Watt complete.

S & F LED Tube light fittings1x 20 Watt ( T-8 ), 4' long, 220 Volts, AC decorative box type with driver,holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F LED Tube light fittings1x 10 Watt ( T-8 ), 2' long, Mirror type, 220 Volts, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED Wall bracket type CITY-2 fitting 9 Watt complete all as specified and directed.

S & F Decorative wall mounting electric fixture with opal glass diffuser suitable with two Nos 9Watt LED complete all as specified and directed.

S &F surface mounting type LED ultra Ceiling light 1'X1', 18 Watt complete all as specified and directed.

S&F LED bulk head luminaire 10 watt with Engineering plastic housing and oval shaped with holder, clear prismatic diffuser,heat sink integrated including one no. 9Watt LED lamp complete all as specified and directed.

S &F LED luminaire 600x600 mm, 35/36 Watt, 220 Volts AC recessed/surface mounted type with high efficiency diffuser soft glare free light with driver, holder & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F DMT 15 watt round false ceiling panel LED light for POP with push button complete all as specified and directed.

S&F DMT 15 watt square false ceiling panel LED light for POP with push button complete all as specified and directed.

S&F Noble LED strip light 6watt IP 20 with LED Driver+ power cord cut table after 3LED 50000 burining horus (Amber) Smfor POP complete all sepecified and directed.

S &F LED building security light fitting 25 Watt,230 Volts, AC outdoor type with high pressure die cast aluminium housing and heat resistant polycarbonate cover complete with driver, lamp & IP 65/66 protection complete all as specified and directed.

S&F in repairs stepped, (socket/switch type) electronic Modular fan regulator flush type, 180 Watt, 240 Volts on the existing phenolic laminated sheet complete all as specified and directed.

S & F Cable TV socket complete all as specified and directed.

S & F Telephone socket complete all as specified and directed.

S & F PVC non metallic conduit including all fittings such as tees, bends,mouth tube ends etc for laying cable for telephone & cable connection complete of size 25mm dia complete all as specified and directed.

S& F decorative Ceiling fan 1200mm sweep complete with all accessories inculding electric connection with three flexible PVC insulatged copper conductor multistranded cable 1.0 sqmm complete all as specified and directed.

S &F Exhaust fan PVC 250mm sweep complete and marking the serial MES fan nos etc including electric connection with three core flexible PVC insulated copper conductor multistranded cable 1.0 sqmm complete all as specified and directed.

Install only Geyser, cleaning all dust etc from surfaces of any size, replacement unseviceable PVC connection etcetc complete including electric connection with three core flexible PVC insulated copper conductor multistranded cable 1.5 sqmm & suitable fastners/ nut bolts etc complete all as specified and directed.

Fixing only and connecting electric meter upto 25 Amp complete all as specified and directed.

M & L in repairs for sub main wiring with 2 run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm alongwith one run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through in & including PVC conduit complete all as specified and directed.

M & L in repairs for sub main wiring with 2 run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through in & including PVC conduit complete all as specified and directed.

S&F in repairs single pole and neutral enclouser having IP -67 protection with a three pin & earth plug with socket complete and one SP, 20 A , 240 V MCB complete all as specified and directed

S&F in repairs sheet metal enclousers (DBS) when MCBs to be used 8 way, 240 Volt, double door single pole & neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F in repairs MCB single phase and neutral 32A, 230V 10KA. B' curve type complete all as specified and directed.

S&F in repairs MCB SP 6A-32A, 230V. 10KA. B' curve type complete all as specified and directed.

S & F in replacement GI bracket made out from GI pipe 25/32mm dia, 1.20 m long fixed on wall with and including nut, bolts and GI clamps of size 25x4mm as required & including painting etc complete.

Taking down service connection/UG cable removing of site complete all as specified and directed.

Excacvation in trenches not exc 1.5 mtr wide and n exc 1.5 mtr in depth for laying of electric cable or water pipe etc n exc 10 sqmm on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm in soft/loose complete as all specified and directed.

Removing excavated materail n exc 50m and deposting where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Supply & laying sub class B bricks, well burnt , laid wirdth wise along the length of cable laid in trench over sand cushion laid for cable protection, complete all as specified and directed.

Material and labour for river washed and sreened, dry sand for filling in trench below and around the under ground cable for cushioning of cable etc, complete all as specified and directed.

Boring of holes under road or cutting the road/path/pavement/hard standing or any other situation by mannual means for 40mm bore GI pipe for crossing the cable and making good both the ends all as specified and directed. Note :- GI pipe shall be measured and paid separately under respective item.

Supply & fix tube 40mm bore light grade GI with all fittings for cable protection for road crossing/ culvert/ path/ on wall/ floor/ pole/ across the road/path/culverts or laid in floor complete all as specified and directed.

Supply and lay cable XLPE insulated PVC armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor cross sectional area 25 Sq mm 4 Core complete all as specified and directed.

S&F sheet metal enclousers (DBS) when MCBs to be used 4way double door three phase & neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F MCB s three phase & neutral of size 100 Amp, 230V, 10KA, B curve type complete all as specified and directed.

S&F in single pole of size 6A-32 Amp 230 volt, B' curve type complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 03 of SSR-I connected to earth test point by means of nut, bolts and washers made out of galvanised iron or steel all including earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) protecation pipe and providing layer of charcoal or coke and salt in alternative layers,necessary earth work complete as specified or indicated including testng on completion. Note : Tenderers may note that amount of credit Rs 1,10,785.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

TEAM ACC INFRABUILD PRIVATE LIMITED