Construction of Multipurpose Hall at Govt. Degree College at Dehri Tehsil Fatehpur Distt Kangra

Amount

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work and chiselling / wedging out of hard or soft rock where blasting is prohibited up to all depths stacking the excavated soil not more than 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping, etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of material in all leads and lifts.

Foundation, footings, bases of columns etc and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs including inclined surfaces up to any degree, landings and the like. (i) Floors, etc. upto 200 mm in thickness.

Columns, Pillars, Posts and struts (i) Square, rectangular or polygonal in plan

Beams, cantilevers, girders and lintels sides and soffits of beams, small ends of beams,beam haunching, cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth in all heights from floors.

Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 sand :8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curring complete excluding cost of form work and reinforcement for reinforced concrete works including carriage of material in all leads & lifts.

Foundation, Footings bases of columns and the like and mass concrete.

Suspended floor, roofs, landings, shelves and their support, balconies, beams, girders, bressumers and cantilevers in all heights.

Columns, Pillars, Posts and struts upto floor two level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all heights.

Applying cement slurry on R.C.C . slab or cement concrete work using 2.75 kg of cement per sqm. of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of material in all leads and lifts.

Providing Tor steel/TMT Steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads and lifts.

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 20 mm nominal size) in cement mortar 1:6.(1 cement: 6 sand) including carriage of material in all leads & lifts.

Providing and fixing 40mm thick panelled door shuters made of 2nd class deodar wood having style and top rail 100mm width and bottom rail 200mm width lock rail 150mm width with panel insert of 12mm thick commercial veneered flat pressed ply wood board of BWP grade confirming to I.S. 303-1975 and bounded with BWP type synthetc resin confirming to I.S. 848-1974 including providing and fixing 2nd class deodar wood beading of size 38X20mm along the panels on both faces of shutters and providing wooden cleats and ISI marked black enamelled M.S. butt hinges with necessary screws all complete as per drawing & specification and instructions of Engineer-In-Charge including carriage of material in all leads and lifts.

Providing and fixing 2nd class deodar wood 40 mm thick wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws as per drawing and specification & as per instruction of Engineer-in-Charge including carriage of material in all leads and lifts.

Providing and fixing 40mm thick single/double leaf glazed window shutter made of 2nd class doedar wood having style and top rail and bottom rail 75mm width and chamferred edged moulding 20X12mm for glass panes complete including bright finished balck enamelled iron hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing M.S. grills of required pattern in wooden /steel /pressed steel chowkhats of window etc.with M.S.flats,square or round bars with round headed bolts and nuts or screws or by welding complete of any design including carriage of material in all leads and lifts.as per Architectural Drg/ Design of HIMUDA.

40 mm thick cement concrete flooring 1:2:4 (1cement:2sand:4 graded stone aggregate 20 mm nominal size) laide one layer finished with a floating coat of neat cement including carriage of material in all leads and lifts.

Kota stone slab 25 mm thick for flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete. including carriage of material in all leads and lifts.

Kota stone slab 25 mm thick in risers of steps, skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. including carriage of material in all leads and lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (300x300mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying vetrified tiles (300x300mmx8mm) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer -in-charge including carriage of material in all leads and lifts.

Painting top of roofs with bitumen of approved Quality at 17 kg for 10 sqm. impregnated with a coat of sand at 0.06 cum per 10 sqm. including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil Complete including carriage of material in all leads & lifts.(a) With residual type perroleum bitumen of penetration 80/100.

Making khurras 45x45cm with average minimum thickness of 5 cm. cement concrete 1:2:4 (1 cement :2 sand: 4 stone aggregate of 20 mm nominal size) finished with 12 mm cement plaster 1:3 (1 cement : 3 sand) and coat of neat cement rounding the outlet complete including carriage of material in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5kg / Sqm including filling the joints with approved adhesive complete, 150 mm dia including carriage of material in all leads and lifts.

Steel work welded in built up sections,trusses and framed work , including cutting , hosting,fixing in position and apply ing a priming coat of red lead paint including carriage of material in all leads and lifts.

In beams joists channels,angles,tees,flats with connection plates or angle cleats as in main and cross beams , hip and jack rafters, purlins connected to common rafters and the like.

In gratings framed guard bars, ladders, railling, brackets and similar works.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mm X2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers, handles, including applying a priming coat of red lead paint including carriage of material in all leads and lifts.

Providing and fixing double rebate angle iron door, window, clerestory window frame manufactured from steel iron section of 40X40X6 mm, thickness with 50x 6mm thick flat iron including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50X25mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 3.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge including carriage of material in all leads and lifts.

Providing and fixing single rebate angle iron door, window, clerestory window frame manufactured from steel iron section of 40X40X6 mm, thickness with 50x 6mm thick flat iron including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50X25mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 3.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge including carriage of material in all leads and lifts.

Providing and fixing anodized aluminium sliding door bolt as per colour and shade approved by the Engineer-in-Charge with bolts and nuts screws etc. complete including carriage of material in all leads & lifts. (a) 300x16mm

Providing and fixing aluminium tower bolt (barrel type) as per colour and shade approved by the Engineer-in-Charge with screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing aluminium handles as per colour and shade approved by the Engineer-in-Charge with necessary screws including carriage of material in all leads & lifts. (Classic, Everite or sheel marked)

Providing and fixing oxidized M.S.hooks and eyes including cost of screws with wooden chowkhats including carriage of material in all leads and lifts. (a) 150mm.

Providing and fixing 100 mm finished brass floor door stopper with rubber cushion screws etc., tosuit shutter thickness complete, including carriage of material in all leads and lifts.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foregin matters including carriage of material in all leads and lifts. (a) Enamel paint other than white.

Painting two coats (excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter , sand papering & stoping including carriage of material in all leads and lifts.(a) With enamel paint other than white / white enamal paint

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting including carriage of material in all leads and lifts.(a) Ready mixed paint brushing wood primer pink.

6mm.cement plaster in cement mortar 1:3 ( 1 cement : 3 sand) to ceiling including carriage of material in all leads and lifts.

15mm cement plaster in cement mortar 1:6 (1 cement:6 sand) in single coat on fair side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts.

20mm cement plaster in cement mortar 1:6 ( 1cement : 6sand) in single coat on rough side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete including carriage of material in all leads and lifts.

Applying Birla white wall care putty two or more coats over plastered surface after thoroughly brushing the surfase free from mortar drops, dust, loose materials and other forign matter sand papered smooth to give final matter finish to the surface complete including carriage of materials in all leads and lifts.(i) In Wall surface / Ceiling

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated ceiling surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth including carriage of material in all leads and lifts. (a) Priming coat with distemper primer.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth including carriage of material in all leads and lifts. (a) Priming coat with distemper primer.

Providing plinth protection 50mm thick in cement concrete 1:3:6 ( 1 cement:3 sand:6 graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75 mm thick (unconsolidated) bed of dry brick / stone aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground complete including carriage of material in all leads and lifts.

Providing & fixing to wall ceiling and floor galvanised mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor confirming to BIS Specifications including carriage of material in all leads and lifts.

15 mm nominal bore.

20 mm nominal bore.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and fixing to wall ceilingand floor Plytheline – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe confirming to IS 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capble to withstand temperature up to 80 degree C, including all special fittings composite materials (Engineering plastic blend brass insertes where ever required) e.g. elbows, tees, reducers, couplers and connectors etc. with clamp at one metre spacing.This includes testing of joints complete as per direction of Engineer-In-Charge including carriage of material in all leads and lifts. (i) 1216 (16 mm O.D. pipe)

Providing and fixing polythene water storage tank for storage of water up to all heights keeping water hygenic and safe for drinking etc.moulded to seamless perfection from FDA approved grades of polythene (LDPE / HDDE / CIDPE) confirming to BIS-12701-1989 with 40 mm nominal bore galvanised steel scoure tube with fittings 25mm nominal bore galvanised mild steel over flow tube with fitting & mosquito proof coupling of approved municipal design 15mm nominal bore ball valve and as per direction of Engineer-in- charge including carriage of materials in all leads and lifts. (i) 1000 liters capacity

Providing and fixing high pressure a PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts.

90 mm dia

110 mm dia

Providing and fixing brass full way valve with wheel including carriage of material in all leads and lifts.

15mm nominal bore.

20 mm nominal bore.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

90 mm dia.

110 mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc, complete including carriage of material in all leads and lifts.

90 mm dia

110 mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc., complete, including carriage of material in all leads and lifts.

90 mm dia

110 mm dia

Providing and fixing 110 mm x 90 mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material in all leads and lifts.

Providing and fixing vitreous China wash down, water closet squatting pan(Indian type W.C pan) size 580 mm (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage of material in all leads and lifts. (confirming to BIS specification) (a) Orissa Pattern.

Providing and fixing vitreous China wash down,water closet European type. W.C.pan) with integral 'P' or'S' trap including jointing the trap with soil pipe in cement mortar1:1 (1cement : 1 sand) (Seat and over to be measured and paid for separately):- including carriage of material in all leads and lifts. (confirming to BIS specification) (a) Angle Indian Universal closet.

Providing and fixing coloured / white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately including carriage of material in all leads and lifts. (a) Flat back type of size 430mm x 260 mm x 350mm.

Providing and fixing C.P.brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc.(all in C.P.Brass) including cutting holes and making good the same including carriage of material in all leads and lifts. (a) 15mm nominal bore.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I.or M.S.brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material in all leads and lifts.(a) Flat back (i) 550mmx400mm

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material in all leads and lifts.

Providing and fixing C.P. Brass waste for wash basin or sink including carriage of material in all leads and lifts.(a) 32mm dia.

Providing and fixing 600mmx450mm bevelled edge mirror of superrior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brassscrews and washers including carriage of material in all leads and lifts and confirming to BIS specifications. (Atul, Modi Guard, Saint Gobains)

Providing and fixing C.P.Brass Towel rail complete with C.P.Brass brackets fixed to wooden plugs with C.P. Brass screws including carriage of material in all leads and lifts.(a) 600x 20mm.

Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden plugs with C.P. brass screws, and confirming to BIS specifications, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P Brass pillar tap with Capstan head 15mm dia with Aerator and confirming to BIS specifications, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing P.V.C. connection with brass unions including carriage of material in all leads and lifts. (a) 300/450mm length (i) 15mm nominal bore.

Providing and fixing C.P.brass angle valve 15 mm without nuts and pipe including carriage of material in all leads and lifts. (Confirming to B.I.S. specification) (ESS-ESS/ CZAR/ NOVA)

Providing and fixing G.I./M.I Union of following sizes (where not included in the items including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

15mm Nominal bore.

20mm Nominal bore.

Providing and fixing 15mm dia long body brass bib tap (Superior or heavy type) (Confirming to BIS specifications) including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube. including carriage of material in all leads and lifts.

Constructing man hole with RCC top slab in 1:2:4 mix (1cement:2sand: 4graded stone aggregate 20mm nominal size ) Foundation concrete 1:4:8 (1cement : 4sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3(1 cement:3 sand) finished with a floating coat of neat cement and including making channels in cement concrete 1:2:4 mix (1cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testng.(a) Inside size 1200 mm x 900 mm and 1000mm deep including S.F.R.C. frame and cover medium duty 500mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) including carriage of materials in all leads and lifts.

Providing and fixing Vitreous China Division Plate for Urinals 600 mm x 300 mm. including carriage of material in all leads and lifts. (Confirming to B.I.S. specification) (ESS-ESS/ CZAR/ NOVA)

ARUN KUMAR

sourav mahajan