WELCOME MAINT AND CERTAIN B/R WORKS IN OFFRS ACCN OF DIFFERENT LOCATIONS AT DOMESTIC AREA, AT AF STN AMBALA UNDER GE (AF) AMBALA

M&L for brooming down surfaces of any description and applying one coat of white wash on old decorated surfaces of walls including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

M&L for brooming down surfaces of any description and applying one coat of white wash on old decorated surfaces of Ceiling including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

M&L for brooming down surfaces of any description and applying two coat of white wash on old decorated surfaces of Ceiling including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

M & L for brooming down surfaces of any description and applying preparation of old wall surfaces, including preparation of old surfaces & filling cracks and holes etc and applying one coats of cement base paint complete all as specified and as directed.

M & L for complete removal of existing treatment and applying two coats of cement based paint on old decorated or undecorated wall surface including preparation of old surfaces & filling cracks and holes etc, complete all as specified and directed.

M&L for Preparing the surfaces of old wall surfaces and applying one coat of distemper oil emulsion complete all as specified and directed

M&L for Preparing the surfaces of old wall surfaces and applying two coat of distemper oil emulsion complete all as specified and directed

M&L for Preparation of old wooden surfaces and applying a coat of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

M & L for painting of old steel surfaces of any description not otherwise described over 10 cm width or girth with one coats of synthetic enamel paint including preparation of surfaces etc complete all as specified and as directed.

Obliterating old writing of any description, not exceeding 0.1 sq. m, with paint to match existing work complete all as specified and directed.

M&L for Writing letters or figures (Block, Roman, Italic or Indian) not exceeding 30 cm high, complete all as specified and directed.

Demolition of Brickwork or stone boulder masonry/PCC block masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework & precast concrete articles and disposing off rubbish outside MD land complete all as specified and directed.

M&L for brick work with sub class B bricks , straight or curved on plan exceeding 6 m mean radius , built in cement mortor 1:6 complete all as specified and directed.

M&L for brick work with sub class'B' bricks,straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Taking down cement plastering of any thickness on brick, concrete or stone walls, partitions, ceilings etc including raking out joints, hacking for key, scrubbing down with water etc, and removing debris out side MD land complete all as specified and as directed.

M&L for 15 mm thick rendering on brick wall or concrete wall or any surface in cement mortar 1:6on fair face/other than fair face and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick rendering on ceilings in cement mortar 1:3 and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

M & L for rough cast plaster incl 15 mm thick CM 1:3 on brick work or concrete surface complete all as specified in SSR Part -1 clause 14.22 complete all as specified . Note:Rough cast plaster finish shall be as follow :- After applying the under coat cement mortar 1:3 and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggreagte ( Which is generally of size between 6 to 12 mm depanding on the texture required mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even . The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure the larger aggregate are throughly covered. Note : i) Area to be plastered may require to be carried out up to height of 15 m, necessary scaffolding and security provision of labour required shall deemed to be included in rate quoted against this item.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed

M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed.

M&L for carrying out water proofing treatment of sunken floor as under:- (i)The concrete/ wall surface shall be cleaned throughly of all laitance , loose particles, dust , grease etc. any friable unsound area shall be chipped, cleaned and there after pre-welted to a saturated surface dried conditions.(ii) In case of potholes , superficial cracks found , the same shall be repaired with polymer modified mortar 1:3 ( 1 cement and 3 coarse sand )using Dr fixit pidicrete URP 301/Sikka latex or equivalent in Asian paints/ Forsoc as admixture @ 10% of cement content and the same shall be applied on vertical area after removing of plaster upto 2 ft height (iii)On the prepared surface , apply a primer coat of Sika latex / Dr. fixit pidicrete URP 301 or equivalent in Asian paints/ Forsocmodified cement slurry 1:4:8 (1 admixture : 4 water : 8 cement) , after prewetting the substrate @ 2 kg/sqm .(iv)the surface thus prepared shall dampen upto saturation and apply two coats of sika top seal 107 or equivalent in Dr fixit piddilite/Asian paints/forsoc ,acrylic modified water proofing coating on the entire area @1.5 kg/sqm (each coat) Scond coat shall be applied after 6-8 hrs after the first coat and in the direction right angle to the previous coat . the water proofing should be taken to a vertical height of minimum 600 mm above .(v) Apply open woven glass fiber mesh of sika Fab 1 or equivalent in Dr fixit piddilite/Asian paints/forsoc, 150 mm wide strip over the PCC benching (Gola) whilst the first coat is wet and then apply scond coat . cure the hydrosent application ( Minimum 6-8 hrs drying) for a minimum 3 to 5 days .(vi)Apply a protection layer of 10 mm thick plaster made of 1:4 cement sand mortar admixed with integral water proofing compound Sika plastocrete plus/ Dr fixit piddilite LW plus or equivalent in asian paints/ forsoc @ 200 ml/bag of cement , applied over the water proofing coating .Note;The rate include the cost of demolition of exiting floor , sub base , PCC/ hardcore filled under floor , removal of debris , removal and replacement of damaged CI/PVC pipes, floor,Nahani traps complete all as specified and directed. .

M&L for Plain Cement Concrete (1:5:10) type E2, using 40 mm graded mechanically crushed stone aggregate as in sunken slab filling, mass concrete etc., complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 using 20mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and as directed. Notes :- (i) The unit rate quoted shall be deemed to include for providing the concrete in alternate bays not exceeding 3 Mtrs length,10 mm wide. (ii) 30 mm deep joints between the bays shall be provided which shall be filled with mastic filling with hot bitumen 85/25 grade and 1:2 mix volume.

Taking down chowkats or frame without taking off shutter from the frame not exceeding 1.50 Sqm each from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3, complete all as specified and as directed.

Taking down chowkates / frame without taking off shutter exceeding 1.50 Sqm not exceeding 4 Sqm each. from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3, complete all as specified and as directed

Taking down Shutters of any description exceeding 1 sq. m and not exceeding 2 sq. m each, complete all as specified and directed.

S&F Factory made solid PVC Chowkhat /Door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm thick rigid PVC foam sheet coloured, reinforced with 19x19mm MS square tube of 19 gauge including rubber gasket, PVC fasteners, screws, brackets as per SSR Part –II (2020) complete all as specified and as directed.

S&F for Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:),With Wood Free EPS with 2,4 or 6 raised panel design with 2 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawin complete all as specified and directed.

M&L for Repair/Rescuing, easing and adjusting wooden door shutter of any description without taking off shutter from the frame, area of shutter exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, including making good the disturbed area as per existing, complete all as specified and directed.

S & F 35 mm thick plain framed panelled factory made shutters(two panel) with IInd class hardwood rail and style with lock rail and panel of 12 mm BWP commercial ply with commercial vaneer on both faces. The size of rail and style as per IS - 1003 Part - I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specsified & directed. Note: The rates for flush shutters include for the provision of suitable blocks for taking mortice locks, latches, or other fittings all as specifed and directed.

S & F 35mm thick IInd class hardwood glazed and skeleton shutters open rebated and prepared to receive gauge (without sash bars)edges of framing plain, chamfered or round fitted with cut and mitred beads for securing wire gauge sizes of members as specified in SSR Part-I section 8 clase 8.24(a) of shutters all as specified and as directed.

M&L for Mild steel framed work such as in doors or gates of angle, or tee sections with gusset plates, rails, braces, etc. completely drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging doors fittings (including of steel sheeting or other covering, running rails and guides) and handing also fastening and fixing complete Gde Fe 410 - W (Grade-E- 250) quality-A complete all as specified and as directed.

Taking down boards of any description and any size as in shelves complete all as specified and directed.

S & F 19 mm thick fire retardant plywood BWR type including cutting, jointing, fixing with screws as in kitchen cabinet box type complete all as specified and as directed

S & F Decorative laminate type1, 0.90 to 1mm thick , of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

M&L for 18/19mm thick one side prelaminated particle board, interior grade, with decorative choice laminate and fixed with screws to steel/timber frame work including provision of 6mm thick teakwood edging etc complete all as specified and directed

S & F in fancy type stainless steel handle of size 100 mm long complete all as specified and as directed

S&F in 40mm dia, cupboard knobs fixed with nut, screw & washer of mild steel, bright finished, complete all as specified and directed

S&F Stainless steel soft close hinges, suitable for modular kitchen complete all as specified and as directed. Make : Godrej or Equivalent as approved by GE

S&F steel ventilator with top hung shutter including hinges peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast size 25 x 5 mm of flat iron etc complete all as specified and directed.

M&L for Preparation of newly steel surfaces of any description over 10 cm width or girth & applying two coats synthetic enamel paint complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and remove the debris outside of MD land, complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality not exceeding 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specified and directed.

All as per BOQ srl Item No.55.00 here-in-above but figured glass complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repair complete all as specified and directed.

S & F Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

S & F Aluminium anodized cast type handles 150mm long all as specified and as directed.

S&F SS butt hinges medium weight of size 100 mm complete all as specified and directed.

S & F door stopper of rubber and aluminium alloy body, 150 mm size fixed complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 30 mm complete all as specified and directed

S & F magnetic ball catches of standard type fixed complete all as specified and as directed

S&F tubular curtain rail, stainless steel anodized 20 mm dia including taking down unserviceable rod/rail any description complete all as specified and directed.

S&F stainless steel type brackets suitable to hold the curtain rod with sofio phenol (Lotto) suitable to curtain rod of 20mm dia, decorative type fixed with suitable steel screws and PVC cleats, including taking down unservicable brackets complete all as specified and directed.

Taking down unserviceable GI tubing, supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Refixing 20mm bore water tubing surface/concealed in same/new location after cleaning and application of bituminous paint on concealed portion of tubing including cutting & threading pipe and provision of additional fittings such as socket, tee, elbow, union (if required) complete all as specified and directed. Note : i) Taps, valves if any shall be removed before taking down pipe. ii) Cutting chases and making good shall be measured and paid separately

Cutting chases pinning in making good for brick walls to facing where required and pointing in cement mortar 1:3 to ends or edges of concealed water tubing and similar work including making good cutting not exceeding 10CM girth. Complete all as specified and directed.

S & F in repair 15 mm CP cast copper alloy bib taps fancy type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S & F 15 mm pillar taps, cast copper alloy fancy type , chromium plated screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe including taking down old pillar taps complete all as specified and as directed.

S & F in repairs CP fancy type angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair chromium plated overhead shower rose 125mm dia with swivel joints with and including overhead shower arm 230mm with wall flange , complete all as specified and directed.

S&F in repairs 15mm, Stop valves (concealed), fancy type with CP wall flanges, chromium plated, cast copper alloy with long shank and exposed part kit with fittings sleeve, operating lever concealed part screwed both ends for iron pipe or for unions, including making good the disturbed portion matching with adjacent surfaces, complete all as specified and as directed

S&F in repair, Chromium plated Wall mixer with bend pipe for overhead shower with built-in non return valve with CP wall flanges, complete all as specified and directed by GE

S&F in repair Centre hole wash basin mixer for wash hand basin make Jaquar Product code No CON-CHR-167KNB and equivalent complete all as specified and directed

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr tube & hook (braded Tube) and ABS valve including making connection and fixed in position complete all as specified and directed.

S&F in repair Single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat etc complete all as specified and directed.

S & F in repair PVC connecting pipe 450mm long 15 mm dia both end having brass coupling nut and PVC washer complete all as specified and directed.

S&F Vitreous china white wash down water closet pan (pedestal pattern) with PP soft closing seat cover, hinges, fixing accessories set (excluding flushing cistern and flush pipe), including UPVC (SWR) ‘P’ or ‘S’ trap and connection to drain (or outgoing pipe) and to flush pipe, antisyphonic pipe fixed in repair including dismantling existing water closet etc complete all as specified and directed by GE”

S&F Vitreous china White Squatting Orissa Pattern pan of size 580x440mm, including UPVC ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe, fixed in repair including dismantling existing squatting pan and making good to disturbed floor, complete all as specified and directed.

S& F Vitreous China wash basin, white, flat back, size 550x400mm excluding waste, chain and plug and porcelain stopper but including brackets, including Waste coupling of PTMT(half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) with 32mm bore PVC waste pipe minimum 800mm long with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repairs complete all as specified and as directed.

S&F in repairs, PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including jointing with new PVC long / short flush bend and making good to the disturbed surfaces complete all as per Model No: CIENA PREMIUM Cat Part No B1010102 of CERA Make or techno commercial equivalent in other makes complete all as specified and as directed.

S & F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen with plugs, waste pipe and washer’s including cast iron cantilever brackets, connecting union etc over all size 915 mm x 460 mm with bowl size 410 x 330 x 160 mm complete all as specified and directed.

S&F stainless steel plate rack of 0.63mm thick sheet, size 24''x30''x10'' complete all as specified and as directed including taking down of old unserviceable kitchen plate rack. Make: silvershine Model SSKPR -311 or equivalent as approved by GE.

S&F in repair PVC waste pipe 32/40mm bore not less than 800mm long complete all as specified and direceted

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F in repair Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball scrured for iron pipe of dia 20 mm bore complete all as specified and directed .

S&F in repair for 15 mm dia Gun-metal, golbe or gate valves/, with iron wheel head, screwed both end sor iron pipe and fixed, complete all as specified and directed.

M & L in repair Gun metal Gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed including cutting the old pipes as in repair complete all as specified and directed

S&F in repair Corner glass self assembly consisting of 5.5mm thick sheet glass self 25cm wide with chromium plated bracket guard and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F in repair glass self assembly consisting of 5.5mm thick sheet glass self 12cm wide with chromium plated bracket guard and rail 60cm long and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S & F PVC (SWR) bends any radius 75 mm dia of bore with access door, including taking down old bends all as specified and as directed.

S & F PVC (SWR) branch piece single (single T)equal of bore 75 mm dia with access door in repairs all as specified and as directed

S & F PVC (SWR) branch piece single (single T) equal or unequal of bore 110 mm dia, with access door in repairs all as specified and as directed

S&F UPVC (SWR) bends any radius, 110mm bore with / without access door, complete all as specified and directed.

S & F PVC (SWR) multi-floor trap, plain with chromium plated grating including jointing with solvent cement, 75mm dia, including dismantling the damaged trap, complete all as specified and directed.

S&F in repair PVC floor trap/Nahani Trap with plain/single hole CP grating including jointing to waste pipe in cement joint, of outlet 75 mm.dia, complete all as specified and directed. .

M & L for welding in repairs to steel windows / doors exceeding 2.5 cm but not exceeding 5.00 cm in length and thickness of metal to be welded not exceeding 6mm complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm below or above ground level removing debris outside MD land complete all as specified and directed.

Demolition of cement concrete of any description and any position not otherwise specifically provided for. and disposing off debris to outside the MOD land complete all as specified and directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles and disposing off debris to outside the MOD land complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, as in floor set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match colour of tiles over and including 15mm thick screed bed of CM 1:6 complete all as specified and as directed.

S & F glazed ceramic coloured printed tiles of size 450 x 300X 7mm as in dado set and jointed in neat cement slurry & pointed in white cement mixed with pigment to match with color of tiles over and including 10 mm thick rendering in cement motor 1:3 complete all as specified and directed.

M&L for Vitrified tiles flooring with Light shade 10 mm thick (Square / rectangular), tiles, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for Vitrified tile, skirting/dado, light shade with 10 mm thick tiles of area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, on vertical rates as in skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including backing coat of 10 mm thick CM 1:3 complete all as specified and as directed.

Demolition of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar and removing debris outside MD land complete all as specified and directed.

M&L for 20mm thick Granite work (of any type) (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in cement white (1:2) using marble dust with admixture of pigment to match the shade of granite, including making hole for gas pipe including half rounding the edges of granite, laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring not less than 18 to 20 mm thick (size of stone shall not less than 55cm x 55cm), 75mm wide white marble border around, laid over & including 15mm thick screed base in CM 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirrior finish with machine, complete all as specified and directed.

M&L for Machine cut Kota stone slab not less than 18 to 20mm thick as in riser of steps, skirting, dado and pillar laid over & including 10mm thick rendring in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified and directed.

S& F GI spout 40 mm dia medium grade to be embeded in sunken floor complete all as specified and directed.

M & L for Rendering 10mm thick in CM 1 : 3 on concrete surface even and smooth on roof surface incl water proof liquid finished when concrete is green complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

Demolition of cement concrete in ground floor and paving not exceeding15cm below or above ground level removing debris outside MD land complete all as specified.

M&L for 60mm thick machine pressed rubber moulded precast concrete M-35 interlocking coloured paver block any shape and size conforming to IS-15658-2006 with grey cement and pigment all as specified as directed.

M&L for Sand filling under floors including watering and consolidation complete all as specified and directed.

M&L for Chequered cement concrete commercial Tiles 30cm x 30cm x 20 to 22mm thick of with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished laid and over 15mm Screed in CM 1:4 complete all as specified and directed.

M&L for 75mm thick PCC type D-2, (1:4:8) using 40mm graded mechanically crushed stone aggregate as in sub base of paving/Inter Locking , Hard standing Etc complete all as specified and directed

M&L for 25 mm thick PCC 1 : 2 : 4 type B0 (using 12.50 mm graded mechanically crushed stone aggregate) as floor rough to receive tile screed/bedding layer complete all as specified and directed

M&L for roof treatment as follows:- Cleaning of dust Removal fo all loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface including removing of vegetation/plantation with no loose material on surface. Repair all joints and cracks with Highly elastic Bituminous cold applied putty of Tarplasic having penetration after setting upto 8mm. Levelling of surface to give proper slope will be done as per site requirements with Shalipatch or equivalent make of approved by GE cold applied, Bituminous Mortar & Cold Emulsion cum waterproofing Liquid of Shalikote-T-10 or equivalent make of approved by GE, Created SSD condition on surface with water. Prime the surface with Tarfelt LM or equivalent make of approved by GE mixed with portable water in the ration of 1 :1 and apply @400gm per Sqm (As per Surface Conditions). . Apply first coat of Tarfelt LM or equivalent make of approved by GE having elongation 200% conforming to ASTM-C-412 & having crack bridging of 8mm confirming to ASTM-C-836 with tensile strength after 7 days 0.50 mm conforming to ASTM-C-412 with no diluation of water on primed surface while the surface is still tacky with consumption of 700gm per Sqm. . Lay Geotex of 45 GSM/ Fibre mesh simultaneously and paste it properly with overlap of 50mm. . Allow the first coat to dry for 10 to 12 Hrs. . Apply 2nd coat on cured first coat with consumption @ 700gm per Sqm in opposite direction of first coat by Brush or Roller. . Allow it to dry for 10-12 hrs after apply 3rd coat with consumption @ 700gm per Sqm. Ensure final curing time of 36 hrs before allowing/ carrying out any further work. Conduct ponding test after min 7 day applying two coats of U V Resistand Elastomeric Exterior Axcrylic Weather resistant water proof coating of Shalicryl-215 or equivalent make of approved by GE having elongation of 300% after curing of 14 days confirming to ASTM D- 6083-- for U V Protection of Bituminous Elastomeric Acrylic Emulsified Liquid Membranc of Tarfelt LM or equivalent make of approved by GE to give long life and prevent its deterioration from sunlight. Note:- Application of water proofing treatment will be done by Authorised Applicator only.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and directed.

M & L Rendering /screed bed 15 mm thick in CM 1 : 3 on concrete surface even and smooth on roof surface, Wall surface incl water proof liquid finished when concrete is green complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,gulley gutter and ridges fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron of mild steel work of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-290(Gde E-165) complete all as specified and directed.

M&L for posts and struts in wall fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by the Engineer-in-Charge

M&L for providing cement concrete in roof, kerbs , interlocking tiles or rounded or chamfered on edged type B-1 1:2:4 ( 20 mm graded mechanically crushed stone aggregate) complete all as specified and directed.

M&L For PCC 1:3:6type C-2 using 40 mm graded mechanically crushed stone aggregate ,Cement concrete in foundations, filling and mass-concrete complete all as specified and directed.

Demolition of RCC of any description & in any position (reinforcement cut as required to facilitate demolition) and disposing off rubbish outside MD land complete all as specified and directed.

M&L for TMT bars upto 10mm dia and above bentt to length bent to shape required including cranking bending etc and binding with mild steel wire (annealed) not less then 0.90mm complete all as specified and directed

M&L for Precast RCC 1:2:4 type B1 (using 20mm mechanically crushed stone aggregate) as in cover slab of drain, culvert and the like set in CM 1:4 complete all as specified and directed.

M&L for RCC 1:2:4 type B-1,nominal mix using 20 mm graded mechanically crushed stone aggregates as,slab, shelves in fins, fascia louvers, parapet and railing complete all as specified and as directed.

M&L for granular textured homogenous wall finishing system consisting of two componet system of dry granules (25 Kgs Pack ) Made of 92% silica particles coated with fade resistant pigments ,100% arcylic polymer bondring agent(5KG pack) with the applied thickness of the coating being between 0.8mm to 1.2 mm to be applied on curved ,smooth level plastered surface , as per direction /supervision of Engr-in charge , all complete , above textured coating should confirm to surface spread of flame class of BS 476 Part 7 :1971 and pull of strength of the coating to meet JISE 6909 all as specified and as manufacture specification /instruction .complete all as specified and directed

Disconnecting existing PVC water tank of capacity not exceeding 500 ltr fixed on roof by setting aside (or lowering, if required) for cleaning and removing all scale and dirt from tanks and from mouths of circulating pipes etc and hoisting/refixing/reconnecting in same/new position including writing date of cleaning on each tank with white paint, height/size of letters/figures not less than 10cm in height, and refixing existing serviceable ball valves complete all as specified and directed.”

Disconnecting existing PVC water tank of capacity exceeding 500 ltr but not exceeding 1000 ltr fixed on roof by setting aside (or lowering, if required) for cleaning and removing all scale and dirt from tanks and from mouths of circulating pipes etc and hoisting/refixing/reconnecting in same/new position including writing date of cleaning on each tank with white paint, height/size of letters/figures not less than 10cm in height, and refixing existing serviceable ball valves complete all as specified and directed.”

Taking down old water tank cover and Supply and fixing Polyethylene water storage tank covers circular or any other type with hinges suitable for 500Ltrs/1000 ltrs capacity tanks all as specified and as directed.

M & L for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Ltrs per Sqm of the vertical surfaces of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M & L for antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 Ltres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for Anti-termite treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and pluging 12mm dia hloles with cement mortar 1:2(1cement:2 coarse sand) to match the existing floors, complete all as specified and directed.

M&L for Anti-termite treatment at point of contract of wood work by chemical emulsion(in oil and kerosene based solution) @ 0.5 litre per hole by drilling 6mm dia hloles at a downward angle of 45 degree at 150mm centre to centre and sealing the same. with cement mortar 1:2(1cement:2 coarse sand) to match the existing floors, complete all as specified and directed.

S&F 300 mm long Mild steel sliding door bolt with hasp & stapple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section, complete all as specified and directed.

Please Enable Macros to View BoQ information