Construction Work Of Aanganvadi and Renovation Work Of Aanganvadi, As Per Location Chart, At. Jetpur-Navagadh Under I.C.D.S. Grant.

NAME OF WORK:- CONSTRUCTION WORK OF ANGANWADI AND RENOVATION WORK OF ANGANWADI, AS

PER LOCATION CHART, AT. JETPUR-NAVAGADH

TOTAL AMOUNT PUT TO TENDER

TOTAL AMOUNT PUT TO TENDER

PERCENTAGE RATE TENDER

Sr.No. Schedule Amount

1 Schedule - "B"- 1

2 Schedule - "B"- 2

3 Schedule - "B"- 3

4 Schedule - "B"- 4

5 Schedule - "B"- 5

Total Amount Rs.

Total Amount Rs.

I/We am/are willing to carry out the work @ ________% Above / Below_____________Percentage (should be writen in

figures and words) of the Estimated rates mentioned above amount of my / our Tender works out as under.

Estimated Amount Estimated Amount

Put to Tender Rs. 47,98,762=00 Put to Tender Rs. 47,98,762=00

Add …………………….% Rs. Deduct …………………….% Rs.

Total Rs. Total Rs.

(In Words (In Words

Stamp with Signature of Contractor

Cons. Engineer Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: INTEGRATED CHILD DEVELOPMENT SERVICES (ICDS)

NAME OF WORK :- CONSTRUCTION WORK OF ANGANWADI

Location :- Somnath Garden Campus, Takudi Para, At- Jetpur

SCHEDULE - "B-1"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation up to 1.5 mt. depth including sorting out and

stacking of useful materials and disposing of the excavated stuff up to all

lead. (B) Dense or Hard Soil 46.18 164.82 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

all lead. (E) Hard Rock 11.46 657.36 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 20.43 4376.38 Cumt

Providing and laying cement concrete 1:3:6 (1 cement, :3 coarse sand :

6 crushed stone aggregate 20 mm norminal size) and curring complete

including cost of form work in (A) Wall caps/coping 5.98 4115.74 Cumt

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20 cm. In depth

consolidating each deposited layer by ramming and watering. 26.89 137.47 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Beam (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 1.70 7048.79 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) Extra for brick work in

superstructure above floor two level (B) Conventional 27.30 4671.52 Cumt

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1

Cement 4 coarse sand) Extra for brick work in superstructure above

floor two level (B) Conventional 6.18 705.60 Sqmt.

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Lintel (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 0.32 6527.63 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Chhajja (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 0.20 7604.29 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Slab (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 6.39 7480.06 Cumt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level 1336.83 77.29 Kg

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 115.82 242.01 Sqmt.

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i)Cement mortar 1:3 (1-cement:3-sand) and finishing with a

floating coat of neat cement slurry. 49.36 194.94 Sqmt.

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of 12 MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete. 242.42 330.72 Sqmt.

Providing and fixing EZ-27 section door/ windows frame including

welding and fixtures fastening including 3 coats of approved enamel oil

paint etc. complete. 10.21 2491.75 Sqmt

Providing and fixing flush door shutters, solid core construction with

frame of firs class hardwood with cross band and face veneer anodised

alluminium butt hinges eith necessary screws. (B) Non-decorative type

and block board core anodized aluminium butt hinges in flush door

shutters. (2) 35 mm. Thick 10.21 1829.74 Sqmt

Providing upto floor two level precast cement concrete jali or grill 1:2:4

mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm

nominal size) reinforced with 1.6 mm dia. Mild steel wire including

roughening,cleaning, fixing and finishing in cement mortar 1:3 and

curing complete. (D) 75mm Thick 3.16 856.09 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc. complete for light shade

Providing and laying polished kota stone slab 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing and polishing etc.

complete. 15.51 1198.64 Sqmt

Providing and laying white glazed tiles 6 mm. Thick in flooring treads of

steps and landings laid on a Bed of 12 mm. Thick cement mortar 1:3 (1

cement : 3 coarse sand) pointing in white cleaned jointed with white

cement slurry 1.35 964.48 Sqmt

Providing and laying white glazed tiles 6mm thick skrting risers of steps

and dedo on 10mm thick cement plaster 1:3 (1-Cement : 3-Coarse

sand) & jointed with white cement slurry. 16.36 1127.48 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and

oxalic acid etc. as directed. 40.94 779.70 Sqmt

Providing and mixing water proofing material in cement concrete in mix

proportion recommended b the manufacturers. 7.37 49.16 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 165.17 88.39 Sqmt

wall primer of approved brand. 165.17 16.52 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 242.42 122.14 Sqmt

Providing, laying and jointing in true line and level for 110mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing, laying and jointing in true line and level for 160mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(E) 40mm dia. 2.00 663.43 No

Providing and fixing screw down bib taps of following size. (A) Brass

screw down bib tap polished bright. (i) 15mm dia. 5.00 186.83 No

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of

cutting and making good the walls. 4.00 614.19 No

Providing and fixing water closet squatting Pan (Indian type W.C. Pan)

size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern =

White colour 1.00 1034.15 No

Providing and fixing 100mm size "P" or "S" trap for water closet

squatting pan including jointing the trap with the pan and soil pipe in

cement mortar 1:1 [1 cement: 1 coarse sand] [A] Viterous china 1.00 348.22 No

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour. 1.00 1657.09 No

Providing and fixing C.P. brass waste for washbasin or sink. (A)

32mmdia. 1.00 67.91 No

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted

white including cutting holes in walls and making good the same but

excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm

size 1.00 2326.66 No

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x

100mm size P type. 2.00 1292.19 No

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 2000.00 3.95 Litr.

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with briocks having croshing strength not less than

35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3516.51 No

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. 358.12 114.44 Kg.

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 11.53 96.59 Sqmt.

Providing and fixing in position callapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel

pulleys complete with bolts, nuts, locking arrangements, stoppers

handles including applying a priming coat of read lead paint. 2.52 6367.62 Sqmt.

Providing & making educational wall painting (fruits, animals, alphabets,

activity scenes etc.) as per approved design including all materials,

colours, artist labour complete 50.80 846.38 Sqmt.

Providing and fixing 0.90 mt height stainless (304 Grade) steel stair

railling by top rail of 50mm dia.x16G pipe providing vertical support of

32x32 Sq. x 16G Pipe and Hori. Supports Pipe of 16mm x 16G 4 No.

Row including grinding, cleaning and filling the welded spots with SS

finish and including of labour transportation loading, unloading and all

tex etc. complete. 4.49 3289.57 Rmt.

ELECTRICAL WORK

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed

on wall/ceiling complete Cat. III 35.00 449.45 Pt.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME four or more

step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose / H.D.Connector as

directed. (a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete Cat. III 3.00 638.32 No.

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire from mcb db board. (a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories Cat. III 10.00 257.55 No.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed (b)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED efficiency-110 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux make

LED used for luminaire. ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) Cat-lll (A) Tube Light with integral

22-24 Watts, Surge - 2KV,IP-20, 4 feet 15.00 373.70 No

5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet 3.00 165.64 No

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size. (A) with medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm 150.00 82.82 Rmt.

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and accessories (b)

2 wire 6.0 sq. mm 100.00 147.46 Rmt.

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity. (a) 6 to 32 Amp. Cat.III 2.00 578.73 No.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark Cat.III 2.00 112.11 No.

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate including

value of earth resistane of installation. [C] For Electrical Installation

covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant

& Sensitive Computer System(like Automation, SCADA)i.e.

independent Earthing located in other than normal soil i.e. Soft

Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg 1.00 10593.89 No.

providing and erecting Cast iron earth plate size 30 X 30 X 0.35 cms.

buried in specially prepared 2.5 Mtr. deep earth pit complete with

necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug

for earthing of switch gear, conduit run or power plug etc. 1.00 685.79 No.

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth bar

and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB

to house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase incoming and

horizontal single phase outgoing (a) single door (IP-30)

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in

RCC slab with Making the site as original. 3.00 43.43 No.

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep

complete having 3 blades aluminium body and blade sets having

ornamental design shanks , canopy erected with earthing. [ Make shall

be approved by Engineer in Charge] 3.00 2311.89 No.

Outdoor street light fitting side entry with clear acrylic /plastic/

polystyrene cover complete with starter, polyester choke copper wound

complete erected with 40/36 watt tube holders. with lead wire and

connections Cat.III 3.00 942.33 No.

Providing and erecting water cooler having storage capacity 80Ltr. &

cooling capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚ C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by evaporating coil,

thermostats, relay etc. complete with necessary inlet & outlet

connection. The body of water cooler will be made from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post carbon filter auto low

& high pressure switches with following size of storage tank & LPH

capacity & erected as directed [A] 10 Ltr / Hr with 7 Ltr StorageTank

Providing and Fixing SS 304 Foldable Checking bed having size 1.50 X

0.60 X 0.75 mm including using of 25mm dia pipe, SS 2mm thick,

matter of 25.4 (1") of 40 density, cover with regine cloth of approved

quality etc completed as directed by Engineer incharge. 1.00 6060.00 No.

Providing and Placing IT wood writing table having size 1.50 X 0.75 X

0.75 mt with one side drawer with using of 19mm thick WP wood, top

cover with 1 mm thick wood type Formica including using of all

necessary material & labour etc completed as directed by Engineer

incharge 1.00 15150.00 No.

Providing and fixing Fabric cloth Curtain having length 1.8 mtr for

covering of checking area including using of alluminum sliding channel

etc complete as directed by Engineer incharge. 6.75 858.50 Rmt.

Providing and Fixing of SS 304 Hanger for bag including using all

necessary materials like SS rail, screw etc completed as directed by

Engineer Incharge. 20.00 252.50 No.

Providing and Fixing pin cushion display board having size 1.20 X

mt including using of alluminum section frame, 18mm thick WB

plywood, nevy blue Cushion cloth pin etc completed as directed by

Engineer Incharge. 1.00 606.00 No.

Providing and fixing PVC modular kitchen cabinet consisting of base and

wall units, made from high quality rigid PVC boards (minimum 15–18

mm thick), including shutters, shelves, drawers, SS hinges, telescopic

channels, handles, magnetic locks, necessary fittings, cutting, fixing,

complete as per design and direction of Engineer-in-charge.

Providing and fixing foldable MS ladder having 0.90mt wide & 3.60mt

long including rod hinge arrangment at middle with ladder including one

coat of red oxide & two coats of oil paint etc completed as directed by

Engineer incharge. 48.60 110.77 Kg.

Providing and fixing of hook of 10mm or 12mm dia including drilling

hole, fixing of male- female thrade fastner sealing the same with appoxy

compound, finishing the same etc complete as directed by Engineer

incharge. 1.00 303.00 No.

Providing and fixing medical device & equipment standio meter height

measuring scale 2.10mt long including fixing in wall with using of all

heavy SS screw, rail etc complete as directed by Engineer incharge. 1.00 1414.00 No.

Providing and supplying standard PVC (Polyvinyl chloride) Chair with

handle of approved design and make as directed by Engineer incharge

Providing and supplying standard PVC (Polyvinyl chloride) Stool having

size 3.75 X 0.60 X 0.45mtr of approved make as directed by Engineer

incharge. 2.00 606.00 No.

Providing & fixing ABC type fire extinguisher 4 kg ISI marked complete

Providing & fixing SANSUI 3 Star LCD (Liquid Crystal Display) Ultra HD

Product Characteristics

Duty Cycle of Product (Number of operation hours per day X number of

days in week) 8 x

Frame Material Enclosing Display Plastic

Color of product (referring Display Frame material) Black

Total number of in-built speaker(s)

Total audio power output of speaker(s) 20 W

Native Resolution of Display (Pixels) Ultra HD (3840 x 2160)

BEE Star Rating of the product 3 Star

Selected BEE Star Rating as per notification S.O. 2785(E) (UHD_TV

Display Characteristics

Diagonal Display Size (in inches) Between 60 and 70 (152.4 and

Display Technology LCD (Liquid Crystal Display)

Type of Backlight in LCD / Type of LED in Display Technology Direct-lit

Type of Panel Technology ADS (Advanced Super Dimension Switch)

Peak display brightness in product (in nits) Between 300 and

Maximum Horizontal Viewing Angle (in deg) Greater than

Maximum Vertical Viewing Angle (in deg) Greater than

Aspect Ratio of Product 16:9

Connectivity Ports

Connectivity Ports available in product Digital Audio Port (Optical),HDMI

HDMI ports available in product 2.0 port with ARC (Audio Return

USB ports available in product USB - A (2.0)

Additional Ports available in product Ethernet,RF Port

Software Characteristics

Operating System in Product Android

Features Supported Media Player,Bluetooth (v 5.1),Wifi 5,Bluetooth (v

Warranty Duration

Minimum Standard Warranty (Year)

Standard Warranty on Product (in Years) 1 1.00 64528.90 No

DRILLING OF 165MM DIA. BORE & INSTALLATION OF SUBMERSIBLE PUMP

Drilling of 165mm dia by DTH Rig in Rocky Formation in all districts of

Zone-III (Except Surendranagar District.) Bore in all types of rocky strata

by DTH Rig and checking the yield of bore by Air compressor

0 to 150 mtr. Deep 50.00 236.00 Mtr.

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials. (180mm) 10.00 736.00 Mtr.

Providing and fixing bore plug having 100mm height made from M.S.

plate with 3 holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of standard make

From 5mm thick MS plate suitable for 175mm dia pipe 1.00 654.96 No.

Supplying approved make electric motor Single phase Borewell sub

pump motor set MOC: Casing: CI-FG260, Impeller : Bronze & Shaft :

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of MPCB,

overload relay and contactors as per Type II coordination including

digital voltmeter, analogue ammeter with selector switch, run hour

meter, required protective relays & control accessories.

DOL upto 3 HP 1.00 24276.00 No.

Supplying PVC insulated flat submersible cable as per detailed technical

specifications of R/C of GWSSB conforming to IS 694, IEC 60227 /

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification,

press fitted and bolted having nominal diameter as under as per detailed

Technical Specification.

32mm dia PN-10 60.00 36.00 Mtr.

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable

450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe 1.00 370.65 Pair

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: INTEGRATED CHILD DEVELOPMENT SERVICES (ICDS)

NAME OF WORK :- CONSTRUCTION WORK OF ANGANWADI

Location :- Somnath Garden Campus, Bapu Ni Vadi, At- Jetpur

SCHEDULE - "B-2"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation up to 1.5 mt. depth including sorting out and

stacking of useful materials and disposing of the excavated stuff up to all

lead. (B) Dense or Hard Soil 46.18 164.82 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

all lead. (E) Hard Rock 11.46 657.36 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 20.43 4376.38 Cumt

Providing and laying cement concrete 1:3:6 (1 cement, :3 coarse sand :

6 crushed stone aggregate 20 mm norminal size) and curring complete

including cost of form work in (A) Wall caps/coping 5.98 4115.74 Cumt

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20 cm. In depth

consolidating each deposited layer by ramming and watering. 26.89 137.47 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Beam (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 1.70 7048.79 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) Extra for brick work in

superstructure above floor two level (B) Conventional 27.30 4671.52 Cumt

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1

Cement 4 coarse sand) Extra for brick work in superstructure above

floor two level (B) Conventional 6.18 705.60 Sqmt.

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Lintel (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 0.32 6527.63 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Chhajja (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 0.20 7604.29 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Slab (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 6.39 7480.06 Cumt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level 1336.83 77.29 Kg

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 115.82 242.01 Sqmt.

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i)Cement mortar 1:3 (1-cement:3-sand) and finishing with a

floating coat of neat cement slurry. 49.36 194.94 Sqmt.

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of 12 MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete. 242.42 330.72 Sqmt.

Providing and fixing EZ-27 section door/ windows frame including

welding and fixtures fastening including 3 coats of approved enamel oil

paint etc. complete. 10.21 2491.75 Sqmt

Providing and fixing flush door shutters, solid core construction with

frame of firs class hardwood with cross band and face veneer anodised

alluminium butt hinges eith necessary screws. (B) Non-decorative type

and block board core anodized aluminium butt hinges in flush door

shutters. (2) 35 mm. Thick 10.21 1829.74 Sqmt

Providing upto floor two level precast cement concrete jali or grill 1:2:4

mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm

nominal size) reinforced with 1.6 mm dia. Mild steel wire including

roughening,cleaning, fixing and finishing in cement mortar 1:3 and

curing complete. (D) 75mm Thick 3.16 856.09 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc. complete for light shade

Providing and laying polished kota stone slab 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing and polishing etc.

complete. 15.51 1198.64 Sqmt

Providing and laying white glazed tiles 6 mm. Thick in flooring treads of

steps and landings laid on a Bed of 12 mm. Thick cement mortar 1:3 (1

cement : 3 coarse sand) pointing in white cleaned jointed with white

cement slurry 1.35 964.48 Sqmt

Providing and laying white glazed tiles 6mm thick skrting risers of steps

and dedo on 10mm thick cement plaster 1:3 (1-Cement : 3-Coarse

sand) & jointed with white cement slurry. 16.36 1127.48 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and

oxalic acid etc. as directed. 40.94 779.70 Sqmt

Providing and mixing water proofing material in cement concrete in mix

proportion recommended b the manufacturers. 7.37 49.16 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 165.17 88.39 Sqmt

wall primer of approved brand. 165.17 16.52 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 242.42 122.14 Sqmt

Providing, laying and jointing in true line and level for 110mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing, laying and jointing in true line and level for 160mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(E) 40mm dia. 2.00 663.43 No

Providing and fixing screw down bib taps of following size. (A) Brass

screw down bib tap polished bright. (i) 15mm dia. 5.00 186.83 No

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of

cutting and making good the walls. 4.00 614.19 No

Providing and fixing water closet squatting Pan (Indian type W.C. Pan)

size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern =

White colour 1.00 1034.15 No

Providing and fixing 100mm size "P" or "S" trap for water closet

squatting pan including jointing the trap with the pan and soil pipe in

cement mortar 1:1 [1 cement: 1 coarse sand] [A] Viterous china 1.00 348.22 No

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour. 1.00 1657.09 No

Providing and fixing C.P. brass waste for washbasin or sink. (A)

32mmdia. 1.00 67.91 No

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted

white including cutting holes in walls and making good the same but

excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm

size 1.00 2326.66 No

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x

100mm size P type. 2.00 1292.19 No

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 2000.00 3.95 Litr.

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with briocks having croshing strength not less than

35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3516.51 No

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. 358.12 114.44 Kg.

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 11.53 96.59 Sqmt.

Providing and fixing in position callapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel

pulleys complete with bolts, nuts, locking arrangements, stoppers

handles including applying a priming coat of read lead paint. 2.52 6367.62 Sqmt.

Providing & making educational wall painting (fruits, animals, alphabets,

activity scenes etc.) as per approved design including all materials,

colours, artist labour complete 50.80 846.38 Sqmt.

Providing and fixing 0.90 mt height stainless (304 Grade) steel stair

railling by top rail of 50mm dia.x16G pipe providing vertical support of

32x32 Sq. x 16G Pipe and Hori. Supports Pipe of 16mm x 16G 4 No.

Row including grinding, cleaning and filling the welded spots with SS

finish and including of labour transportation loading, unloading and all

tex etc. complete. 4.49 3289.57 Rmt.

ELECTRICAL WORK

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed

on wall/ceiling complete Cat. III 35.00 449.45 Pt.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME four or more

step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose / H.D.Connector as

directed. (a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete Cat. III 3.00 638.32 No.

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire from mcb db board. (a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories Cat. III 10.00 257.55 No.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed (b)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED efficiency-110 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux make

LED used for luminaire. ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) Cat-lll (A) Tube Light with integral

22-24 Watts, Surge - 2KV,IP-20, 4 feet 15.00 373.70 No

5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet 3.00 165.64 No

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size. (A) with medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm 150.00 82.82 Rmt.

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and accessories (b)

2 wire 6.0 sq. mm 100.00 147.46 Rmt.

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity. (a) 6 to 32 Amp. Cat.III 2.00 578.73 No.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark Cat.III 2.00 112.11 No.

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate including

value of earth resistane of installation. [C] For Electrical Installation

covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant

& Sensitive Computer System(like Automation, SCADA)i.e.

independent Earthing located in other than normal soil i.e. Soft

Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg 1.00 10593.89 No.

providing and erecting Cast iron earth plate size 30 X 30 X 0.35 cms.

buried in specially prepared 2.5 Mtr. deep earth pit complete with

necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug

for earthing of switch gear, conduit run or power plug etc. 1.00 685.79 No.

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth bar

and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB

to house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase incoming and

horizontal single phase outgoing (a) single door (IP-30)

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in

RCC slab with Making the site as original. 3.00 43.43 No.

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep

complete having 3 blades aluminium body and blade sets having

ornamental design shanks , canopy erected with earthing. [ Make shall

be approved by Engineer in Charge] 3.00 2311.89 No.

Outdoor street light fitting side entry with clear acrylic /plastic/

polystyrene cover complete with starter, polyester choke copper wound

complete erected with 40/36 watt tube holders. with lead wire and

connections Cat.III 3.00 942.33 No.

Providing and erecting water cooler having storage capacity 80Ltr. &

cooling capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚ C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by evaporating coil,

thermostats, relay etc. complete with necessary inlet & outlet

connection. The body of water cooler will be made from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post carbon filter auto low

& high pressure switches with following size of storage tank & LPH

capacity & erected as directed [A] 10 Ltr / Hr with 7 Ltr StorageTank

Providing and Fixing SS 304 Foldable Checking bed having size 1.50 X

0.60 X 0.75 mm including using of 25mm dia pipe, SS 2mm thick,

matter of 25.4 (1") of 40 density, cover with regine cloth of approved

quality etc completed as directed by Engineer incharge. 1.00 6060.00 No.

Providing and Placing IT wood writing table having size 1.50 X 0.75 X

0.75 mt with one side drawer with using of 19mm thick WP wood, top

cover with 1 mm thick wood type Formica including using of all

necessary material & labour etc completed as directed by Engineer

incharge 1.00 15150.00 No.

Providing and fixing Fabric cloth Curtain having length 1.8 mtr for

covering of checking area including using of alluminum sliding channel

etc complete as directed by Engineer incharge. 6.75 858.50 Rmt.

Providing and Fixing of SS 304 Hanger for bag including using all

necessary materials like SS rail, screw etc completed as directed by

Engineer Incharge. 20.00 252.50 No.

Providing and Fixing pin cushion display board having size 1.20 X

mt including using of alluminum section frame, 18mm thick WB

plywood, nevy blue Cushion cloth pin etc completed as directed by

Engineer Incharge. 1.00 606.00 No.

Providing and fixing PVC modular kitchen cabinet consisting of base and

wall units, made from high quality rigid PVC boards (minimum 15–18

mm thick), including shutters, shelves, drawers, SS hinges, telescopic

channels, handles, magnetic locks, necessary fittings, cutting, fixing,

complete as per design and direction of Engineer-in-charge.

Providing and fixing foldable MS ladder having 0.90mt wide & 3.60mt

long including rod hinge arrangment at middle with ladder including one

coat of red oxide & two coats of oil paint etc completed as directed by

Engineer incharge. 48.60 110.77 Kg.

Providing and fixing of hook of 10mm or 12mm dia including drilling

hole, fixing of male- female thrade fastner sealing the same with appoxy

compound, finishing the same etc complete as directed by Engineer

incharge. 1.00 303.00 No.

Providing and fixing medical device & equipment standio meter height

measuring scale 2.10mt long including fixing in wall with using of all

heavy SS screw, rail etc complete as directed by Engineer incharge. 1.00 1414.00 No.

Providing and supplying standard PVC (Polyvinyl chloride) Chair with

handle of approved design and make as directed by Engineer incharge

Providing and supplying standard PVC (Polyvinyl chloride) Stool having

size 3.75 X 0.60 X 0.45mtr of approved make as directed by Engineer

incharge. 2.00 606.00 No.

Providing & fixing ABC type fire extinguisher 4 kg ISI marked complete

Providing & fixing SANSUI 3 Star LCD (Liquid Crystal Display) Ultra HD

Product Characteristics

Duty Cycle of Product (Number of operation hours per day X number of

days in week) 8 x

Frame Material Enclosing Display Plastic

Color of product (referring Display Frame material) Black

Total number of in-built speaker(s)

Total audio power output of speaker(s) 20 W

Native Resolution of Display (Pixels) Ultra HD (3840 x 2160)

BEE Star Rating of the product 3 Star

Selected BEE Star Rating as per notification S.O. 2785(E) (UHD_TV

Display Characteristics

Diagonal Display Size (in inches) Between 60 and 70 (152.4 and

Display Technology LCD (Liquid Crystal Display)

Type of Backlight in LCD / Type of LED in Display Technology Direct-lit

Type of Panel Technology ADS (Advanced Super Dimension Switch)

Peak display brightness in product (in nits) Between 300 and

Maximum Horizontal Viewing Angle (in deg) Greater than

Maximum Vertical Viewing Angle (in deg) Greater than

Aspect Ratio of Product 16:9

Connectivity Ports

Connectivity Ports available in product Digital Audio Port (Optical),HDMI

HDMI ports available in product 2.0 port with ARC (Audio Return

USB ports available in product USB - A (2.0)

Additional Ports available in product Ethernet,RF Port

Software Characteristics

Operating System in Product Android

Features Supported Media Player,Bluetooth (v 5.1),Wifi 5,Bluetooth (v

Warranty Duration

Minimum Standard Warranty (Year)

Standard Warranty on Product (in Years) 1 1.00 64528.90 No

DRILLING OF 165MM DIA. BORE & INSTALLATION OF SUBMERSIBLE PUMP

Drilling of 165mm dia by DTH Rig in Rocky Formation in all districts of

Zone-III (Except Surendranagar District.) Bore in all types of rocky strata

by DTH Rig and checking the yield of bore by Air compressor

0 to 150 mtr. Deep 50.00 236.00 Mtr.

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials. (180mm) 10.00 736.00 Mtr.

Providing and fixing bore plug having 100mm height made from M.S.

plate with 3 holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of standard make

From 5mm thick MS plate suitable for 175mm dia pipe 1.00 654.96 No.

Supplying approved make electric motor Single phase Borewell sub

pump motor set MOC: Casing: CI-FG260, Impeller : Bronze & Shaft :

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of MPCB,

overload relay and contactors as per Type II coordination including

digital voltmeter, analogue ammeter with selector switch, run hour

meter, required protective relays & control accessories.

DOL upto 3 HP 1.00 24276.00 No.

Supplying PVC insulated flat submersible cable as per detailed technical

specifications of R/C of GWSSB conforming to IS 694, IEC 60227 /

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification,

press fitted and bolted having nominal diameter as under as per detailed

Technical Specification.

32mm dia PN-10 60.00 36.00 Mtr.

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable

450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe 1.00 370.65 Pair

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: INTEGRATED CHILD DEVELOPMENT SERVICES (ICDS)

NAME OF WORK :- CONSTRUCTION WORK OF ANGANWADI

Location :- Navagadh Khataki Vas, At- Jetpur

SCHEDULE - "B-3"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation up to 1.5 mt. depth including sorting out and

stacking of useful materials and disposing of the excavated stuff up to all

lead. (B) Dense or Hard Soil 46.18 164.82 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

all lead. (E) Hard Rock 11.46 657.36 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 20.43 4376.38 Cumt

Providing and laying cement concrete 1:3:6 (1 cement, :3 coarse sand :

6 crushed stone aggregate 20 mm norminal size) and curring complete

including cost of form work in (A) Wall caps/coping 5.98 4115.74 Cumt

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20 cm. In depth

consolidating each deposited layer by ramming and watering. 26.89 137.47 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Beam (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 1.70 7048.79 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) Extra for brick work in

superstructure above floor two level (B) Conventional 27.30 4671.52 Cumt

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1

Cement 4 coarse sand) Extra for brick work in superstructure above

floor two level (B) Conventional 6.18 705.60 Sqmt.

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Lintel (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 0.32 6527.63 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Chhajja (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. 0.20 7604.29 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Slab (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. 6.39 7480.06 Cumt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level 1336.83 77.29 Kg

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 115.82 242.01 Sqmt.

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i)Cement mortar 1:3 (1-cement:3-sand) and finishing with a

floating coat of neat cement slurry. 49.36 194.94 Sqmt.

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of 12 MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete. 242.42 330.72 Sqmt.

Providing and fixing EZ-27 section door/ windows frame including

welding and fixtures fastening including 3 coats of approved enamel oil

paint etc. complete. 10.21 2491.75 Sqmt

Providing and fixing flush door shutters, solid core construction with

frame of firs class hardwood with cross band and face veneer anodised

alluminium butt hinges eith necessary screws. (B) Non-decorative type

and block board core anodized aluminium butt hinges in flush door

shutters. (2) 35 mm. Thick 10.21 1829.74 Sqmt

Providing upto floor two level precast cement concrete jali or grill 1:2:4

mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm

nominal size) reinforced with 1.6 mm dia. Mild steel wire including

roughening,cleaning, fixing and finishing in cement mortar 1:3 and

curing complete. (D) 75mm Thick 3.16 856.09 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc. complete for light shade

Providing and laying polished kota stone slab 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing and polishing etc.

complete. 15.51 1198.64 Sqmt

Providing and laying white glazed tiles 6 mm. Thick in flooring treads of

steps and landings laid on a Bed of 12 mm. Thick cement mortar 1:3 (1

cement : 3 coarse sand) pointing in white cleaned jointed with white

cement slurry 1.35 964.48 Sqmt

Providing and laying white glazed tiles 6mm thick skrting risers of steps

and dedo on 10mm thick cement plaster 1:3 (1-Cement : 3-Coarse

sand) & jointed with white cement slurry. 16.36 1127.48 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and

oxalic acid etc. as directed. 40.94 779.70 Sqmt

Providing and mixing water proofing material in cement concrete in mix

proportion recommended b the manufacturers. 7.37 49.16 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 165.17 88.39 Sqmt

wall primer of approved brand. 165.17 16.52 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 242.42 122.14 Sqmt

Providing, laying and jointing in true line and level for 110mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing, laying and jointing in true line and level for 160mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(E) 40mm dia. 2.00 663.43 No

Providing and fixing screw down bib taps of following size. (A) Brass

screw down bib tap polished bright. (i) 15mm dia. 5.00 186.83 No

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of

cutting and making good the walls. 4.00 614.19 No

Providing and fixing water closet squatting Pan (Indian type W.C. Pan)

size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern =

White colour 1.00 1034.15 No

Providing and fixing 100mm size "P" or "S" trap for water closet

squatting pan including jointing the trap with the pan and soil pipe in

cement mortar 1:1 [1 cement: 1 coarse sand] [A] Viterous china 1.00 348.22 No

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour. 1.00 1657.09 No

Providing and fixing C.P. brass waste for washbasin or sink. (A)

32mmdia. 1.00 67.91 No

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted

white including cutting holes in walls and making good the same but

excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm

size 1.00 2326.66 No

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x

100mm size P type. 2.00 1292.19 No

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 2000.00 3.95 Litr.

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with briocks having croshing strength not less than

35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3516.51 No

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. 358.12 114.44 Kg.

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 11.53 96.59 Sqmt.

Providing and fixing in position callapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel

pulleys complete with bolts, nuts, locking arrangements, stoppers

handles including applying a priming coat of read lead paint. 2.52 6367.62 Sqmt.

Providing & making educational wall painting (fruits, animals, alphabets,

activity scenes etc.) as per approved design including all materials,

colours, artist labour complete 50.80 846.38 Sqmt.

Providing and fixing 0.90 mt height stainless (304 Grade) steel stair

railling by top rail of 50mm dia.x16G pipe providing vertical support of

32x32 Sq. x 16G Pipe and Hori. Supports Pipe of 16mm x 16G 4 No.

Row including grinding, cleaning and filling the welded spots with SS

finish and including of labour transportation loading, unloading and all

tex etc. complete. 4.49 3289.57 Rmt.

ELECTRICAL WORK

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed

on wall/ceiling complete Cat. III 35.00 449.45 Pt.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME four or more

step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose / H.D.Connector as

directed. (a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete Cat. III 3.00 638.32 No.

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire from mcb db board. (a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories Cat. III 10.00 257.55 No.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed (b)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name

120 to 300 V,Power Factor more than 0.9, THD < 10 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED efficiency-110 lumens/watt

LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux make

LED used for luminaire. ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) Cat-lll (A) Tube Light with integral

22-24 Watts, Surge - 2KV,IP-20, 4 feet 15.00 373.70 No

5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet 3.00 165.64 No

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size. (A) with medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm 150.00 82.82 Rmt.

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and accessories (b)

2 wire 6.0 sq. mm 100.00 147.46 Rmt.

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity. (a) 6 to 32 Amp. Cat.III 2.00 578.73 No.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark Cat.III 2.00 112.11 No.

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate including

value of earth resistane of installation. [C] For Electrical Installation

covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant

& Sensitive Computer System(like Automation, SCADA)i.e.

independent Earthing located in other than normal soil i.e. Soft

Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg 1.00 10593.89 No.

providing and erecting Cast iron earth plate size 30 X 30 X 0.35 cms.

buried in specially prepared 2.5 Mtr. deep earth pit complete with

necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug

for earthing of switch gear, conduit run or power plug etc. 1.00 685.79 No.

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth bar

and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB

to house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase incoming and

horizontal single phase outgoing (a) single door (IP-30)

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in

RCC slab with Making the site as original. 3.00 43.43 No.

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep

complete having 3 blades aluminium body and blade sets having

ornamental design shanks , canopy erected with earthing. [ Make shall

be approved by Engineer in Charge] 3.00 2311.89 No.

Outdoor street light fitting side entry with clear acrylic /plastic/

polystyrene cover complete with starter, polyester choke copper wound

complete erected with 40/36 watt tube holders. with lead wire and

connections Cat.III 3.00 942.33 No.

Providing and erecting water cooler having storage capacity 80Ltr. &

cooling capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚ C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by evaporating coil,

thermostats, relay etc. complete with necessary inlet & outlet

connection. The body of water cooler will be made from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post carbon filter auto low

& high pressure switches with following size of storage tank & LPH

capacity & erected as directed [A] 10 Ltr / Hr with 7 Ltr StorageTank

Providing and Fixing SS 304 Foldable Checking bed having size 1.50 X

0.60 X 0.75 mm including using of 25mm dia pipe, SS 2mm thick,

matter of 25.4 (1") of 40 density, cover with regine cloth of approved

quality etc completed as directed by Engineer incharge. 1.00 6060.00 No.

Providing and Placing IT wood writing table having size 1.50 X 0.75 X

0.75 mt with one side drawer with using of 19mm thick WP wood, top

cover with 1 mm thick wood type Formica including using of all

necessary material & labour etc completed as directed by Engineer

incharge 1.00 15150.00 No.

Providing and fixing Fabric cloth Curtain having length 1.8 mtr for

covering of checking area including using of alluminum sliding channel

etc complete as directed by Engineer incharge. 6.75 858.50 Rmt.

Providing and Fixing of SS 304 Hanger for bag including using all

necessary materials like SS rail, screw etc completed as directed by

Engineer Incharge. 20.00 252.50 No.

Providing and Fixing pin cushion display board having size 1.20 X

mt including using of alluminum section frame, 18mm thick WB

plywood, nevy blue Cushion cloth pin etc completed as directed by

Engineer Incharge. 1.00 606.00 No.

Providing and fixing PVC modular kitchen cabinet consisting of base and

wall units, made from high quality rigid PVC boards (minimum 15–18

mm thick), including shutters, shelves, drawers, SS hinges, telescopic

channels, handles, magnetic locks, necessary fittings, cutting, fixing,

complete as per design and direction of Engineer-in-charge.

Providing and fixing foldable MS ladder having 0.90mt wide & 3.60mt

long including rod hinge arrangment at middle with ladder including one

coat of red oxide & two coats of oil paint etc completed as directed by

Engineer incharge. 48.60 110.77 Kg.

Providing and fixing of hook of 10mm or 12mm dia including drilling

hole, fixing of male- female thrade fastner sealing the same with appoxy

compound, finishing the same etc complete as directed by Engineer

incharge. 1.00 303.00 No.

Providing and fixing medical device & equipment standio meter height

measuring scale 2.10mt long including fixing in wall with using of all

heavy SS screw, rail etc complete as directed by Engineer incharge. 1.00 1414.00 No.

Providing and supplying standard PVC (Polyvinyl chloride) Chair with

handle of approved design and make as directed by Engineer incharge

Providing and supplying standard PVC (Polyvinyl chloride) Stool having

size 3.75 X 0.60 X 0.45mtr of approved make as directed by Engineer

incharge. 2.00 606.00 No.

Providing & fixing ABC type fire extinguisher 4 kg ISI marked complete

Providing & fixing SANSUI 3 Star LCD (Liquid Crystal Display) Ultra HD

Product Characteristics

Duty Cycle of Product (Number of operation hours per day X number of

days in week) 8 x

Frame Material Enclosing Display Plastic

Color of product (referring Display Frame material) Black

Total number of in-built speaker(s)

Total audio power output of speaker(s) 20 W

Native Resolution of Display (Pixels) Ultra HD (3840 x 2160)

BEE Star Rating of the product 3 Star

Selected BEE Star Rating as per notification S.O. 2785(E) (UHD_TV

Display Characteristics

Diagonal Display Size (in inches) Between 60 and 70 (152.4 and

Display Technology LCD (Liquid Crystal Display)

Type of Backlight in LCD / Type of LED in Display Technology Direct-lit

Type of Panel Technology ADS (Advanced Super Dimension Switch)

Peak display brightness in product (in nits) Between 300 and

Maximum Horizontal Viewing Angle (in deg) Greater than

Maximum Vertical Viewing Angle (in deg) Greater than

Aspect Ratio of Product 16:9

Connectivity Ports

Connectivity Ports available in product Digital Audio Port (Optical),HDMI

HDMI ports available in product 2.0 port with ARC (Audio Return

USB ports available in product USB - A (2.0)

Additional Ports available in product Ethernet,RF Port

Software Characteristics

Operating System in Product Android

Features Supported Media Player,Bluetooth (v 5.1),Wifi 5,Bluetooth (v

Warranty Duration

Minimum Standard Warranty (Year)

Standard Warranty on Product (in Years) 1 1.00 64528.90 No

DRILLING OF 165MM DIA. BORE & INSTALLATION OF SUBMERSIBLE PUMP

Drilling of 165mm dia by DTH Rig in Rocky Formation in all districts of

Zone-III (Except Surendranagar District.) Bore in all types of rocky strata

by DTH Rig and checking the yield of bore by Air compressor

0 to 150 mtr. Deep 50.00 236.00 Mtr.

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials. (180mm) 10.00 736.00 Mtr.

Providing and fixing bore plug having 100mm height made from M.S.

plate with 3 holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of standard make

From 5mm thick MS plate suitable for 175mm dia pipe 1.00 654.96 No.

Supplying approved make electric motor Single phase Borewell sub

pump motor set MOC: Casing: CI-FG260, Impeller : Bronze & Shaft :

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of MPCB,

overload relay and contactors as per Type II coordination including

digital voltmeter, analogue ammeter with selector switch, run hour

meter, required protective relays & control accessories.

DOL upto 3 HP 1.00 24276.00 No.

Supplying PVC insulated flat submersible cable as per detailed technical

specifications of R/C of GWSSB conforming to IS 694, IEC 60227 /

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification,

press fitted and bolted having nominal diameter as under as per detailed

Technical Specification.

32mm dia PN-10 60.00 36.00 Mtr.

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable

450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe 1.00 370.65 Pair

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: INTEGRATED CHILD DEVELOPMENT SERVICES (ICDS)

NAME OF WORK :- RENOVATION WORK OF AANGADWADI

Location :- Khodiyar Dhar, Navagadh, Aangadwadi, At - Jetpur

SCHEDULE - "B-4"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 158.68 88.39 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete. 125.44 122.14 Sqmt

Applying priming coat of over new steel and other metal surface after

and including preparing the surface by thoroughly cleaning, oil grease,

dirt and other foreign mater and scoured with brushes fine steel wool,

scrapers and sand paper with ready mixed priming paint brushing red le

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brusing interior to give an even shade

including cleaning the surface an even shade including cleaning the

surface of all dirt, dust and other foreign matter. 8.73 96.59 Sqmt

Appliying priming coat over new wood and wood based surface after and

including preparing the surface by throughly cleaning oil, grease, dirt and

other foreign matter, sand papering and knotting. (C) Ready mixed paint

brushing priming for enamel 23.01 44.10 Sqmt

Painting one coats (excluding priming coat) on previously painted wood

and wood based surface with enamel paint, to give an even shade

including cleaning the of all dirt, dust and other foreign matter. 23.01 60.89 Sqmt

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3516.51 No

Providing, laying and jointing in true line and level for 160mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Providing, laying and jointing in true line and level for 110mm diameter

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

Drawing picture on existing wall including finishing surface and all paint,

colour and required material and as per guide nagarpalika engineer

(Related swachchha bharat mission, climate exchage and other save

water etc) 120.00 846.38 Sqmt

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: INTEGRATED CHILD DEVELOPMENT SERVICES (ICDS)

NAME OF WORK :- RENOVATION WORK OF AANGADWADI

Location :- Opp. Bhadar River, Aangadwadi No 1, At - Jetpur

SCHEDULE - "B-5"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 165.17 88.39 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete. 134.28 122.14 Sqmt

Applying priming coat of over new steel and other metal surface after

and including preparing the surface by thoroughly cleaning, oil grease,

dirt and other foreign mater and scoured with brushes fine steel wool,

scrapers and sand paper with ready mixed priming paint brushing red le

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brusing interior to give an even shade

including cleaning the surface an even shade including cleaning the

surface of all dirt, dust and other foreign matter. 6.71 96.59 Sqmt

Providing and fixing flush door shutters, solid core construction with

frame of firs class hardwood with cross band and face veneer anodised

alluminium butt hinges eith necessary screws. (B) Non-decorative type

and block board core anodized aluminium butt hinges in flush door

shutters. (2) 35 mm. Thick 13.36 1829.74 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and

oxalic acid etc. as directed. 40.94 779.70 Sqmt

Providing and mixing water proofing material in cement concrete in mix

proportion recommended b the manufacturers. 7.37 49.16 Lit/Kg

Drawing picture on existing wall including finishing surface and all paint,

colour and required material and as per guide nagarpalika engineer

(Related swachchha bharat mission, climate exchage and other save

water etc) 93.00 846.38 Sqmt

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika