PROVN OF TOILET BLOCK FOR LADIES AND GENTS AT SSE AND SPL REPAIR TO SERVENT QTR AND PATH OF QTR NO. P-1744 IN SSE AT ARMY AREA JODHPUR UNDER GE (ARMY) NO. 01

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in any type soil complete all as specified.

Excavation in trenches n exc 1.5m wide and n exc 1.5mtr depth and getting out in any type soil complete all as specified.

Returning filling in,including spreading,levelling,watering and well ramming in layers n exc 25cm in soil complete all as specified.

Removing excavated soil n.exc 50mtr and depositing where directed at a level n exc 1.5 mtr above the starting point.

M&L for hardcore of broken stone or boulders of guage n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15cm thick, watered and rammed to a true surface.

M&L for cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified

Material & labour Providing precast cement concrete solid building blocks masonery 1:2:4 Type B1 (Using 20 mm graded stone aggregates) or slabs exc. 10cm in width with plain, joints setting in mortar built in CM (1:6) as in as in walls complete all as specified and directed.

Material & labour for Providing precast cement concrete solid building blocks masonery 1:2:4 Type B1 (Using 20 mm graded stone aggregates) or slabs 10cm thick with plain or interlocking joints setting in mortar built in CM (1:4) as in as in walls complete all as specified and directed.

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 1-1/2 : 3 (using 20mm graded aggregate) as in footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 1-1/2 : 3 (using 20mm graded aggregate) as in column, pillars, piers, posts and strut etc.

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 1-1/2 : 3 (using 20mm graded aggregate) as Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 1-1/2 : 3 (using 20mm graded aggregate) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Use and waste of formwork to sides of concrete foundation, footings, bases of column, rafts, plinth beams and similar work vertical or to batter rough finished surface flat of concrete, With water tightness.

Use and waste of Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Circular on plan complete all as specified and directed by Engr-in-Charge.

Use and waste of Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; exc. 200m thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

Use and waste of formwork to Edges of concrete flats, treads, breaks in floors.concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC band in walls, sloping and similar work for fair finished surfaces. Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Material & labour for 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Ditto, but on stone masonary surface or other than fair faces of brick masonry complete all as specified and directed by Engr-in-Charge.

Material & labour for 15 mm thick rendering on stone masonry surface or other than fair faces of brick work or concrete surfaces,in CM (1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

Ditto, but using integral water proofing liquid compund as per manufactures instruction complete all as specified and directed by Engr-in-Charge. Note :- INPC shall be measured & paid separately.

Material & labour for 5 mm thick rendering in CM 1:3 on ceiling/Chajja surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for PCC (1:4:8) type D-2, 75 mm thick (using 40 mm graded stone agg) as sub base complete all as specified.

M&L Non-skid coloured ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing complete all as specified.

M&L Coloured Glazed ceramic tiles in vertical surfaces tiles 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.09 Sqm but n exc 0.16 Sqm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) omplete all as specified.

M&L for Solid PVC Door frame of size 50mm x 47mm made out of 5mm PVC sheet reinforced suitable for solid PVC door suppling & fixing in opening, complete all as specified.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F Butt hinges, 100 mm long of stainless steel complete all as specified & directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised size of handle 150 mm

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed length of bolt 150 mm

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy.

Supply and fixing Aluminium anodised ventilator frame and shutter incl all fittings etc including jointing cleat for fixing complete.

S&F stainless steel I- Max hinges for suitable to aluminium ventilators complete all as specified and directed

S&F aluminium alloy wire cloth o.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples.

S&F 3 mm thick sheet glass ordinary quality frosted on one side and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge.

Supply & fix 3mm thick figured glass, pin headed, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

M&L for 20m thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, counter type platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as specified and as directed.

S&F Counter type wash basin white/coloured of size 630x450mm, including CP fixed over Garnite and RCC slab inclduing 15mm bore Swan neck pillar taps cast copper alloy chromium plated fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe fixed with CP Waste coupling 32m and waste pipe complete all as specified and as directed.

S&F Vitreous China wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including provision of lime concrete bedding white and making good floor including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed.

S&F Vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

S&F Vitreous China squatting plate urinal type with including providing & fixing of plugs bedding floor in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

Supply & fix PVC low level flushing cistern of 10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls incl stack clamps of 50mm x 3 mm MS flat iron with bolts & nuts.

M&L PVC SWR floor trap, plain with grating including joining to waste pipe fixed in cement concrete type B-1 (1:2:4) 75 mm dia complete all as specified.

M&L PVC (SWR) multifloor trap 75 mm dia with grating including jointing with solvent cement complete.

S&F PVC (SWR) 110mm bore pipes single socketed in any length witlh rubber ring joints laid in trenches or in floors all as spd

S&F PVC (SWR) 75mm bore pipes single socketed in anoy length witlh rubber ring joints laid in trenches or in floors complete all as specified.

S&F PVC (SWR) bend 110mm dia radius with oval access door complete all as specified.

PVC (SWR), junction single, (Single T) equal or unequal 110 mm bore

S&F PVC (SWR) bends with access door of radius 75mm dia

S&F PVC Connection 15 x450mm size with PTMT Nuts at both ends with rubber washers complete all as specified.

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/Urinal complete all as specified & directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminium alloy brackets and gaurd and railing 60cm long complete all as specified

S& F Brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges

S&F 15mm bore fancy type CP Bib tap (long body) brass with capstan head screw down for iron pipe or for brass furrel complete all as specfified.

Supply & fix angular valve, 15 mm bore, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F Unplaticised PVC 40 mm bore pipes of pressure rating 10 Kg/CM2 fixed complete to wall ceilings or in floor etc including necessary specials.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) over roof as in roof kerb to match the existing.

M&L for rendering over roof slab with CM 1:4, 20 mm thick finished even and smooth (without using extra lime or cement mixed with water proofing compound, all as specified and directed. Note:- WPC shall be measured & paid separately.

Material & labour for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen, over laid with 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm as per manufacturer’s instructions and finished top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm complete all as specified and directed.

Supply only integral water proofing compound.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for applying two coats of cement based paint over a coat of primer including preparation on newly plastered surface of wall.

M&L 75 mm thick PCC 1 : 3 : 6, type C1, (by using 20mm graded stone aggregate) for plinth pretection finishing even and smooth without using extra cement, Including expansion joint every three metre and change in direction and joint tobe filled with sealing compound Gde A complete all as specified and directed.

M&L 50 mm thick PCC 1 : 3 : 6, type C1, (by using 20mm graded stone aggregate) for plinth pretection finishing even and smooth without using extra cement, Including expansion joint every three metre and change in direction and joint tobe filled with sealing compound Gde A complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including one 20mm ball brass valve with polythene float and fly nut complete all as specified and directed.

Supplying and laying of CPVC pipes, 20 mm outer dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall complete all as specified.

Supplying and laying of CPVC pipes, 25 mm outer dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall complete all as specified.

M&Lfor 100 mm thick PCC (1:4:8) type D-2 using 40 mm stone aggregate as in Sub Base

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 40 mm bore and fixed

S &F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore and fixed

M&L for connecting 40 mm bore GI pipe from existing water supply line including necessary excavation , clamping making holes to existing pipe line

S & F 40 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

S & F 25 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

M&L for squarred rubble walling Jodhpur type regular course, well bonded, bedded & solidly hearted, built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throating including use and waste of necessary form work etc complete all as specified

M&L for Providing precast cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in cover slab for man hloes set in CM 1:6.

S&F Mild Steel TMT bars 6mm dia to 8mm dia , cut to length , bent to shape required, incld cranking, bending spirally for hooping for columns, hooking ends and binding with and incld mild steel wire (annealed) not less thaan 0.90mm dia or securing with clips

S&F 150mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars all as specified and directed by engr in charge

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to pipe including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore.

M&L for Cutting into existing manholes for connecting new drain pipe and making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4th Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required.

Demolition of concrete of any description and in any position not other wise specifically provided for complete all as specified and directed

M&L for type C1 1:3:6 (20 mm graded aggregate) Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar in CM 1 : 6 , complete

All as per item No. 86 above but except block

Demolition of PCC as in ground floors and pavings n. exc. 15 cm thick (below or above GL) complete all as directed.

M&L for 25 mm thick Cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) as in sub floors etc incl finishing the surface even & rough to receive screeding complete all as specified and directed by Engr-in-Charge.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match .

M&L for Machine cut kota stone slab flooring 17-20 mm thick over 15 mm thick cement screed bed in CM 1:6 laid and jointed with grey cement clurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

All as per item No. 91.00 here-in-above but as in dado/skirting inluding 10 mm thick screed bed in Cm 1:4 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles digital print series in vertical surface 300x450 mm size 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match . Note :- The tiles shall be in one or more colour patterns incl highlighters all as approved & directed at site .

M&L for Double charged light coloured Vitrified Ceramic tiles 9-10 mm thick area of each tiles not exc 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

All as per item No. 94.00 here-in-above but as in in vertical surface as in dado/skirting.

M&L digital ceramic heavy duty parking tiles 8 to 10 mm thick (square / rectangular) area of each tile exc. 0.08 Sqm but n. exc. 0.16 Sqm as in floors etc, and set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm thick screed bed in CM 1:4 and including demolition, complete all as per specified & directed by Engg.-in-charge.

M&L for 15 mm thick Screed bed or bedding layer of CM1:4 for laying floor finishes .

M&L for 10 mm thick rendering in CM1:3 over stone masonry surfaces & finished even & rough to receive tiles.

M&L for RCC nominal mix type B-1 (1:2:4) using 20 mm graded stone aggregate on walls, beams and columns in floors, roofs, landings, balconies, canopies and in shelves and the like including necessary form workk complete all as directed

Taking down steel water tubing 15 mm dia and connections, including cleaning for re-fixing or remove to store all as specified.

All as above but 20 mm dia

S & F in repair pre-painted galvalume aluminium sheets zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M& L for Steel work in tubular trusses including special shaped washer etc complete using EWR or induction butt welded Tubes conforming to I.S. 1161-1998 grade St 240

M&L in repairs of 4 mm thick prepainted and designer type E-board in false ceiling (flat or sloping) of size fixed to and including anodised aluminium snap grid frame size of grid 605 x 605 mm, 4 mm GI wire for hanging and including dismantling, complete all as specified and as directed by Engg.-in-charge.

M& L for Preparation of new/old plastered surfaces & applying two coat of wall care putty to remove all depressions etc incl sandpapering the surfaces & obtain a smooth surfaces complete all as specified & directed.

M&L for applying 2 coats of Oil Bound distemper over putty applied surfaces . The OBD shall be in one or more colours/ shades all as directed at site.

M& L for Preparation of new surfces plastered /pointed & applying two coats of exterior emulsion paint over a coat of suitable primer,complete all as specified and as directed.

M&L in repair for 15-18 mm thick Udaipur green stone machine cut mirror polished laid in flooring over 15 mm thick screeding in CM 1:4 complete incl rubbing & polishing complete.( size of stone shall not be less than 58x58 cm),complete all as specified and as directed.

S&F as in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed fixed.

S&F in replacement 500 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms, including complete all as specified and as directed.

S&F 15mm bore CP brass concealed stop cock screwed for iron pipe or ferrule and fixed complete all as specified and directed

S&F Over head Shower rose 150x150 mm of ABS Body chrome plated with grey face plate & with arm having swivel joint cromium plated best quality

S&F Light coloured (Ivory) vitreous china, wash hand basin of size 550mm X 400mm flat back with pedestal Including bracket , CP waste coupling ,chain and plug, 2 Nos PVC connection 15 mm size & 45-60cm long & PVC Waste coupling & flexible waste pipe complete all as directed.

S&F in replacement in vitreous china squatting Pan, Orissa Pattern of size 580X440mm white (ISI marked) with integral foot rests and cast iron `P' or `S' trap front or back inlet Including flush pipe 40mm dia HDPE pipe etc, fixed in repairs Including connection to trap etc and provision of cement concrete bedding and making good to floor completely all as directed.

S&F of Pillar taps, fancy type Cast copper alloy, with capstan heads chromium plated, screwed down high pressure, with or without lettered 'Hot" or Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15mm bore pipe

S&F in replacement Stainless steel sink with draining board,made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as directed.

S&F Stainless steel plate rack of size 30"x24"x10" size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks /fittings complete all as per sample .

S&F Corner Glass shelf 250mm superior quality with CP tubular framing & brackets complete all as per sample.

Dismentling of cast iron/PVC soil waste & vent pipes 100 mm dia incl all fittings etc complete.

Dismentling of cast iron/PVC soil waste & vent pipes 75 mm dia incl all fittings etc complete.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with oval acess door

S&F 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with oval acess door

S&F in repair curtain rod stainless steel finish of pipe 22 to 25 mm dia including Purpose made brackets trade pattern for decorative type curtain rods and Decorative finials (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area nexc 1.50 Sqm & removal to store

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50Sqm but nexc 4 Sqm

Taking down steel windows/vents complete with guard bars, wire cloths including frame & remove from site complete all as specified.

S&F mild steel framed work such as in door frame, grills gratings,etc,with ends of bar shouldered and /or riveted .or forged into spikes , framed guard bars, ladders all as specified and directed conforming to Fe-290 Grd E-165.

S&F 35 mm thick flush shutters, solid core construction with block board core and plywood face panels, including 1mm thick laminated commercial type on both sides fixed with suitable adhesive, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F 35 mm thick factory made second class hardwood Plain Gauged door shutter (three panel) with lock rail. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S & F Factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (suspension grade), calcium caronate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum nd screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , odulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category of being termite / borer proof, water / moiture proof and fire retardant and fixing with stainless steel butt hinges of required ie with necessary full body threaded star headed counter sunk SS screws, all as per direction of engr-in-charge complete all as directed

S & F Factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows & other frames/chowkkat of size 45x85 mm comprising of virgin polymer of K value 58-60 (suspension grade), calcium caronate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mmiter joints after applying PVC solvent cement and screwed with full dody threaded star headed SS screws having minimum density of 650 kg/cum nd screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength 58 N/mm2 , modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category of being termite / borer proof, water / moiture proof and fire retardant and fixed in positin with suitable MS hold fast /lugs/SS dash fasteners f required dia and length complete, all as per direction of engr-in-charge complete all as directed

S&F Aluminium alloy, anodised, sliding door bolt 300mm size with hasp, staple (bolt type) and fixing clips of sheet,cast orextruded sections& fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Mild steel Butt hinges, medium weight, cold rolled mild steel, and fixed 100 mm size

S&F 125 mm size single action spring hinge bright finished body of mild steel with steel wire spring heavy duty all as per the sample complete all as spd & directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire & avg width of appertuer 1.40 mm fixed to Anodised aliminium framework of windows / vents & door shutters etc ccomplete.

S&F steel windows with side hung shutters incl box type hinges with steel handles peg stays complete with glazing bars dovetailed or welded.

All as per item No. 138.00 here-in-above but without glazing bar

S&F steel ventilator with top hung shutter incl hinges, steel peg stay complete .

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over & including M&L single coat of pink primer complete all as specified and as directed .

M& L for fabrication of powder coated aluminium frame work as in frames for aluminium windows with or without rebate or for sliding windows(two track/three track ) , ventilators etc with louvers having suitable mechanism for tilting , deco grill, U shaped fillets for securing Jallies etc & the likes complete all as per sample kept in GE Office & fixed in position complete all as directed Note : Glass panes in louvers & stainless steel wire cloth shall be measured & paid for seperately,

M& L for Pre powder coated aluminium window shutters prepared for sliding or hanging etc including handles, tower bolt and hinges complete using section having wt not exc 0.50 kg/RM all as directed & specified

M& L for 4.80 mm thick plain Sheet glass tinted , ordinary quality and glazing withsecured in wooden beads or snap fit glazinng clips square exc 0.5 sq. m in each pane

M&L for 30 mm thick PCC (1:2:4) type B-0 using 12.50 mm stone aggregate as in floor including 28 mm width glass dividing strips 3 mm thick complete all as specified and directed

M& L for 150 mm bore Salt-glazed stoneware drain pipes of grade 'A' laid in trenches and jointed as specified

M&L for modular point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FR-LSH cable (RYBN) 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FR-LSH cable (Green) 1100 Volts grade as earth continuity wire connected to earth dolly and including modular sunken galvanized terminal boxes of same make of switch/ socket/ regulator with sleek and curvy cover plates, for mounting of modular switches, sockets, fan regulators complete for the following :-

One light Fan point controlled by one, one way switch

One socket outlet 3 pin 5 or 6 Amps socket outlet on independent board.

One socket outlet 3 pin 5 or 6 Amps socket outlet on same board.

All as per Srl item No. 149.00 here-in-before but with 4 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board

S&F modular switch 1 way 6 Amp, 1 module complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module complete all as specified and directed.

S&F modular socket 6 Amp/16 Amp, 6 pin combined 2 module complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F sheet metal enclosures 230 volt SPN 4 way with 200 Amp rated bus bar, double door DB's suitable for provn for a MCB One SPN 32 Amps as incoming and 2 Nos of SP Outgoing complete all as specified and directed by Engr-in-charge. Note : MCB/RCCB TPN/SPN/SP measured and paid saperatly.

Supply and fixing MCB SPN 32A,10KA Breaking capacity

S&F of Exhaust fan made of sturdy Engineering Plastic complete with louvers shutters voltage 230V, 50HZ RPM 1200 copper winding of sweep 300m

Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 10 sqmm 2 core all as diredted by Engr - in - charge. Note : Earth work and brick work measured and paid separately

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

Taking down carefully UNSV of any size/ any type cable and all as directed.

M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, all as specified, directed and shown on drgs for The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge.

One light point controlled by one, one way switch

One fan/ Exhaust Fan point controlled by one way switch.

One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per srl item no. 162.00 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

Supply and fixing bell push AC, 230 Volts, 5 Amps incl dismentling of old unserviceable bell push of any make .

Supply and fixing bell AC ding dong type 230 volts

S&F Switch piano type, single pole, one way, 6 amps, 230 volts, complete all as specified and directed. .

S&F Socket, two-in-one, 3 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed. .

S&F Switch piano type, single pole, one way, 16 amps, 230 volts, complete all as specified and directed. .

S&F Socket, 6 pin, 6/16 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed..

S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed..

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge. Make: Philips/Havells/Bajaj

S&F Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed. .

S&F electric storage water heater of capacity 25 litres BEE 5 star rated including proper installing arrangment on wall surface with suitable Anchor bolt fatser and Geyser connections for hot and cold water supply made of stainless steel wire braided connrtector with chrome finish heavy duty nuts of 15mm size with suitable lengh etc complete all as directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long all as specified and directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable complete all as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). All as specified and directed by eng-in-charge.

S&F of Heavy duty Exhaust fan 300 mm sweep, 900 RPM, copper winding including louvers with cutting chases on brick wall and grounting with nut bolts complete all as specified and directed by Engr-in-charge

S&F MCB, B Curve type, 10 kA, 63Amp, SPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

Supply and fixing as MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and directed by the Engr-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, nnected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 5 connected to Earthing test point all as ecified or indicated including testing on completion( Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover & GI 15 mm dia protection pipe upto 7.5 mtr. lead etc. complete )

Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 2 core all as diredted by Engr - in - charge. Note : Earth work and brick work measured and paid separately

Supply and lay sand for sand cushioning for cable protection in trenches all as directed and specified in SSR Part - 1.Note:. for the purpose of payment only punned thickness will be measured.

Supply and laying Un reinforced Precast concrete cable cover, of class LV, type-2 flat size 300 mm x 180 mm x 40mm all as directed

Supply and fix GI tubing medium grade of 40 mm dia for cable protection.

Ashwani Associates (BID ID -3277644)

Sejal construction company (BID ID -3282845)

M/S SUMAN ENTERPRISES (BID ID -3282026)