Construction of Auditorium Block under Vinod Bihari Mahto Koylanchal University, Dhanbad

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing average 150mm thick dry rammed khoa beaten to112mm.(compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thckness is achieved, curing and carriage of water with all leads,making proper slope and blending the top with cement morter (1:10) all complete as per building specification and direction of E/I

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. @ Size of Tile 600x600 mm .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.,

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately) - White sand stone - 30mm thick gang saw cut stone

Providing and fixing carpet floor and dado tiles on existing surface as per approved colour and design fixing in approve design all complete as per direction of engineer in charge100% solution dyed universal nylon 6 material/ polypropelene/ polyester make Thickness - 7.5 mm ASTM E648-10 Class 1 certifies

Providing and fixing 15 mm thick Laminated wood flooring/Skirting with top layer of 3 mm th. Oak wood & bottom layer of 10+2 mm of spruce wood, Shade with planed, levelled smooth etc. all complete as specified and as directed by the Engineer-in-Charge. Providing and fixing 15 mm thick wooden PARKUET flooring with approved soild wood, Shade with planed, levelled smooth etc. all complete as specified and as directed by the Engineer-in-Charge

Epoxy flooring on basement deck whichis colorful, low VOC, solvent free, epoxy car park flooring solution, fire resistance EN 13501-1, slip resistance as per method described in BS 7976-2, thermal tolerance upto 60 degree, impermeable, upto 5 mm thickness

Providing and laying cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : ,….. 1:2:4(1cement:2coarse sand (zone-III):4 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) included attached buttresses, string or lacing courses ,….. 1:2:4 (1 cement: 2 coarse sand(zone III):4 graded stone concrete 40mm nominal size)

Providing 50 mm thick cement concrete flooring (1:2:4) with 20 mm to 6mm size graded stone chips finished with floating coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/l

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Reinforced cement concrete work in beams, suspended floor, roofs having slove uo to 15° landing , balconis , shelves, chajjas , lintels, bands, plains window sills , stairases and spiral stair cases above plinth level up to floor five level , excluding cost of centering, shuttering , finishing and reinforcement . 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 grade stone aggregate 20mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for :- Columns, Pillars, Piers, Abutments, Posts and Struts

Providing designation 100 A brick work with fly ash lime brick ( flag) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. ( 1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints , cost of screening materials , raking out joints to 150 mm depth , curing , taxes and royalty all complete

Providing Designation 100A 112 mm thick reinforced B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 12 mm. cement plaster ( 1: 6) with clean coarse sand of F.M. 1.5 including screening , curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete - exluding textured paint area

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper ,applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction E/I.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing and fixing in position wall panelling of redence Esto channelled Wood panels of width 128mm, thickness of 16mm and length 2440 mm made up of high density fiber board with minimum density of 800 Kg/m3 substrate with a laminated facing/wood veneer as per the approved shade / species & finish with melamine balancing layer on the reverse side. The boards shall have a special perforation pattern of 2mm groove & 14mm pitch. The panels shall have fire resistance of Class I, BS 476 part 7. The edges of the panels shall be "tonguedand- grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece and backed with 50mm thick glass wool layer as directed by the Engineer-in-Charge. The panel shall be mounted on special channels using clips as approved by the Engineer-in-charge.

Providing & fixing of modular toilet cubicles (Sturdo Classique of Greenply Industries or Titan Standard 12 mm series of Merino of approved equivalent) consisting of high pressure 12 mm thick compact laminate board as per IS 2046 (Indian Standards) and as per fire retardant BS-476/97 standards with phenolic core panels for partitions of intermediate divider, doors and pilasters(. The cubicle shall have dimensions of 1200 mm depth x 850 mm width x 2050 mm height with a door size of minimum head rail on top of panels and panels shall be fixed on the floor with a clearance of maximum 150 mm using stainless steel satin finish adjustable legs screwed to the floor included stainless steel (SS) lock set, SS door knob, SS gravity self closing hinge, SS coat hook with door stopper, SS U channel, SS head rail, SS adjustable foot, SS tabular holder, SS head rail wall bracket, SS head rail corner connection and SS noise reducing tape, etc. (all SS accessories shall be of Grade 304) as per direction of Engineer-Incharg

Providing and Fixing of GRC screen of approved make 30mm thick (sieds/borders 50 mm thick) including cost of fastners & fixtures at site complete as per the direction of Engineer in charge (unistone or equivalent)

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. 10 MM 10%

providing Tor steel reinforcement of 20mm,25mm,& 28mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)@ 12.29kg/sqm (Mumpty Room)

Providing and fixing glazed railing with stainless steel ( Grade 304) frame work made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1 mm thick

Providing and fixing bright finished brass 100 mm mortice latch andlock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm. At 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and fixing Credence Astra soft fiber acoustical false ceiling micro- look edged tiles at all heights of size 595X595X15 mm. The tiles should have Humidity Resistance (RH) of 90%, thermal insulation ≥ 0.5 (m² k / w) & moisture rate ≤ 1% (JC/T670-2005), light Reflectance of >85%, and fire retardant as per Class A in true horizontal level suspended on interlocking T- Grid of hot dipped all round galvanized iron section of 0.30 mm thickness (galvanized @120 gsm) comprising main T runners of 15x32 mm of length 3000 mm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Styrofill Geofoam Blocks, Thickness Dead Load 15KG/M3, Load Bearing Capacity – 2.5 Tons / M2

Design and Execution of Post tensioned beam along with Post tensioning Strand

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm

Excavation in soil by manual means : Excavation for roadway in using manual meams including laoding in truck for carrying of cut earth to embankmant site with all lifts and lead upto 1000 metres.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Cost of drilling 200mm X 165mm X 125mm deep bore well in all kinds of soil and rock in rural area for installation of pump set withhydraulic DTH rig machine , all complete including supplying all materials , tools , drilling rig , air compresser and equipments, as well as fuel , lubricants and cost of transportation of rig machine and other vehical up to the site up to the site ( basic rates ) . (a) From 0.00 M to 50.00 M below G.L

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200mm Nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Supplying and stacking at site dump manure from approved source,including carriage upto 5 km complete (manure measured in stacks will bereduced by 8% for payment) :Screened through sieve of I.S. designation 4.75 mm

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Topiary of Ficus Panda

Marigold jaffri

Dracaena

Rabbit Dustbin

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm, FRLS PVC insulated copper conductor single core cable etc. as required.Group B

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm, FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Twin control point wiring in PVc conduit,with modular type switch: wiring for twin control light point with 1.5sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, 2 way modular type switch, modular plate, suitable size GI box as required.

Wiring for circuit / submain wiring along with earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. 2 x 2.5 sq.mm + 1x 2.5 sq.mm earth wire

2 x 4 sq.mm +1x 4 sq.mm earth wire

2 x 6 sq.mm +1x 6 sq.mm earth wire

2 x 10 sq.mm +1x 6 sq.mm earth wire

4 x 6 sq.mm +2x 6 sq.mm earth wire

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

S/F Modular boxes, base & cover plate - Supplying and fixing following size/modulaes G.I. box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 (78mm x 78mm x 45mm)

4/5 module (78mm x 140mm x 50mm)

6 module (78mm x 205mm x 50mm)

8/9 module (78mm x 230mm x 60mm)

12 module (135mm x 205mm x 60mm)

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F Modular type switch socket - Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required 5/6 amps, one way switch

5/6 amps, two way switch

15/16 amps, one way switch

5/6 amps, 3 pin socket outlet

15/16 amps, 6 pin socket outlet

Supply and fixing 2 pin, 5A ceiling rose on the existing junction box / wooden block including connection etc as required.

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan upto 450mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Providing and fixing following rating, breaking capacity four pole MCCB, existing cubical panel board / DB including drilling holes in cubicle panel, making connections etc as required. 630 Amp, 35kA, adjustable thermal setting

Supplying and fixing following way single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnection, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 12 way double door

Supplying and fixing following way horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnection, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 4 way Double Door

6 way Double Door

8 way Double Door

Supplying and fixing following way vertical type three pole and neutral,sheet ,MCB distribution board, 415 volts, on surface / recess complete with tinned copper busbar, neutral bus bar, earth dinbar ,din bar, detachable gland plate, interconnections,phosphatized and powder painted,including earthing, etc. as required. , (but without MCB's and incomer), as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required). 4 way (8+12),double door, vertical type

8 way (8+24 ),Double door, vertical type

Supplying and fixing following,240 volts, C series minature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connection,testing and commissioning etc.as required 6/32 amps,Single pole

6/32 amps,Double pole

6/32amps TPN

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double p ole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps `C' curve, SP, MCB in sheet steel enclosure on surface or in recess, with chained metal cover for the socket outlet and complete with connections testing and commissioning etc, as required.

Supply & installing following size of perforated Hot dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforations not more than 17.5%, including bends, tees, cross member, reducer etc in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including GI bolts & nuts etc as required. 300 mm width x 62.5 mm depth x 2 mm thickness

Chemical earthing using 50mm dia Earthing electrode 2m length, backfill compound chemical 4 bag(per bag 25kg), earth cutting removingand installation charge.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4mm dia copper wire on surface or in recess for loop earthing as required.

MV cable laying upto 400 sq.mm. in ground - Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 120 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

PVC/XLPE insulated PVC sheathed heavy duty armoured electrical cable with aluminium conductor for voltage up to and including 1100 volts (Conforms to IS 1554, part 1) 3.5C x 120 sq.mm

Providing and supplying in standard lengths High Density Polyethylene Pipe (HDPE Pipe) 25mm to 500mm dia confirming to IS 4984/14151/12786 / 13488 (Latest Revision with necessary jointing materials like mechanical connector i.e. thread/ insert joint / quick release coupler joint / compression fitting joint or flanged joints excluding coupler / specials and taxes. Note: The Rates are F.O.R at worksite in Jharkhand including Royalty, inspection Charges and other taxes HDPE material grade of PE 100 - PN06 (dia in mm) : 250 mm

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required. 10/12W LED Tube light

20/22W LED Tube light

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722 with all necessary accessories as required 12 W LED Square down light

2'x2' LED Panel light

Supplying and fixing of 15" (380mm)metal exhaust fan

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200MM(48") BLDC 5 STAR RATING CIELING FAN

Supply & erection of LED 10W Bulk Head: Supply and erection commissioning of LED bulk head comprising of pressure die cast housing with acrylic diffuser(IP 65 protection)d clear glass. Make- Bajaj /Havells/Jaquar)

Supply of Wallmounted Fan(16"/400mm): Supplying and fitting of 400 mm Sweep wallmounted fan , including connection with 1.5 sq mm copper wire with all accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC.

LED Flood Light 150W:Supply installation Testing and Commissioning of LED flood lighting( 150W ) luminarie with prssure die cast housing and toughened glass cover (IP-66 protection in existing pole/ pipe for supply voltage 100-270 volts AC, 50Hz. Luminarie shall confirming to IS:10322 part-5/ section -5 and shall be conecessary accessories as per required. ( Make -Wipro/Bajaj / Havells/ Jaquar)

Supply, installation, testing & commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman?s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless steel faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding, electrical panel, logic control panel and shaft lighting etc required for the erection of the elevators as required. Position of Machine Directly above the lift well - elevator shall be of gearless type (suitable for lift well size 2200mm (W)X 2100m(D)) complete as per technical specification, micro processor based simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 900mm wide X 2000mm height capacity (minimum 408 Kgs)8 Passenger Lift , car size of 1800x1700x2200 (mm wide*mm depth *mm height*mm C - value) Inside dimensions and entrance at front side on all the serving floors, provided with Hairline finish stainless steel panel on all four side and ceiling, complete as per specifications. 6floors & 6stops ,Total travel height is maximum upto 20 M

Providing and fixing C.P. brass 2 way bib cock of Jaquar make or equivalent (FLP-5041PM) conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall 40 mm nominal outer dia pipes UPTAKE PIPE

FLUSH water supply

Cold water supply

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 15 mm nominal outer dia pipes Cold water supply

Flush water supply

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm nominal outer dia pipes Cold water supply

Flush water supply

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm nominal outer dia pipes

Providing and fixing C.P. brass angle valve with flanges of approved quality of Jaquar (FLP-5053PM) or equivalent make as per direction of the Engineer-in-charge. 15 mm nominal bore

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Supplying fitting and fixing vitreous Rimless EWC With cistern for extended wall Hung WC with PP Soft Close Seat Cover, Hinges, Dual Flush Cistern fitting with flow rate of 3/6 LPF of Jaquar make(FLS-WHT-5353PPZ) or equivalent as per specification and direction of E/I. (a) lit. 6/3 litre level Vitreous Cistem

Supplying, fitting and fixing Handshower health faucet -1 meter long easy flex tube in chrome finish (ALD- 579) and wall hook of approved quality of Jaquar or equivalent make for european type W.C pan as per direction of the Engineer-in-charge.

Supplying fitting and fixing vitreous Rimless WC for Handicapped Toilet with UF Soft Close Seat Cover (DIS-WHT-93753P180UF), Hinges, Dual Flush Cistern fitting with flow rate of 3/6 LPF of Jaquar make(DIS-WHT-93201) or equivalent as per specification and direction of E/I.

Supplying fitting and fixing vitreous white glazed earthen ware wall Hung wash hand basin size 565x450x195mm (CNS-WHT-303) with full pedestal (CNS-WHT-811) of Parry/Hindustan/ Jaquar or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste Coupling(ALD-705) , 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal (URS-WHT-13261) of ‘Hindustan/Parry /jaquar" or any other approved I.S.S make with with all fittings with C.I.or R.S. brackets, standard size G.I. flush pipe with fitting clamps,15mm Auto Closing Pressmatic Urinal Valve(PRS-077) 15mm P.V.C./Alkthene pipe 450mm long as per specification and direction of E/I. (a) Flat back (355mmx340mmx535mm)

Supplying fitting and fixing of special type of C.P bath room fittings for V.I.P buildings (Kohler, Jaguar, Grohe or Equivalent) jointof approved make including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Central hole basin mixer (FLP-5001BPM) of make Jaquar or equivalent

Sink mixer with swinging casted spout (FLP-5179BPM) of make Jaquar or equivalent

Wall mixer with provision for over head shower with elbow coupling and wall flange ( FLP-5273PM)

Angular Stop Cock (Long Thread) (ISI Marked) (FLP-5053PM)

Concealed stop cock reduce (ALD-089CQT) with exposed part lever and flange (FLP-5083KPM)

Towel Rail 24" (ACN-1111SM) of make Jaquar or equivalent

Towel Ring (ACN-1121BN) of make Jaquar or equivalent

Soap dish (ACN-1131N) of make Jaquar or equivalent

Tumbler Holder (ACN-1141N) of make Jaquar or equivalent

Toilet Paper Holder (ACN-1151N) of make jaquar or equivalent

Glass Shelf 600mm long (ACN-1171N) of make Jaquar or equivalent.

GRAB ROD

Supplying and fixing H.C.I. Fitting of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I. (J) Floor trap with grantings 100 MM DIA

Supplying, fitting and following items complete with all materials as per specification and direction of E/I (b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. Brass revolving fitting 3mm ply wood board and C.P. Hinges to fix with mirror. (i) 600mm X 450mm size

Supply, fixing, testing and commsisioning of PVC (Class-3 ,0.6Mpa) SWR quality IS 13592 soil waste vent pipe including all fittings shall be 13591 , Eg: Bends, tees, elbows collars, juction, inspection doors, cowls, offset acess pipes, jointing with PVC solution, in making bores punctures in slab and wall and making good of the same, including running of pipes ceiling suspended with brackets and fasteners, cost shall include providing steel brackets and fasterners. ( Make : Finolex / Supreme / Prince ) a. 75mm dia

b. 110mm dia

Supply, fixing, testing and commsisioning PVC soil waste vent pipe of Class 3 (6 Kgf/cm2) conforming to IS 4985-2000 including all fittings (IS 7834 for moulded fittings and IS 10124 for fabricated fittings), Eg: Bends, tees, elbows collars, juction, inspection doors, cowls, offset acess pipes, jointing with PVC solvent, running of pipes suspended from the ceiling with brackets and fasteners, chasing / chipping walls using groove cutting machine, making bores / core cutting in slab / beam / wall and making good of the same, cost shall include providing steel brackets, MS angle supports, Pipe supports (all MS angle supports / frames to be painted with two coats of primer) and fasterners. The cost shall include transportation, lead and lift all complete as required a. 40mm dia

b.63mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with sealring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including fittings etc (i) Single socketed pipes. 160mm diametre

Polythene water storage tank of mark with cover and Suitable locking system in double layer confirming to IS: 12701-1996 with Latest revision. flushing water tank

fire water tank

(B) Providing double flange sluice valve (Size 50 mm to 1200 mm) confirming for IS2906/14846 including worn gear arrangements as per test pressure stailess steel spindle, caps, transportation etc. all complete. With bypass arrangment pn1.6 50 mm dia

,Design, Supplying, installation, testing and commissioning of solar water heating system with heat exchanger type including electrical heater backup, make up water tank complete in all respect as per direction of E/c

Supplying submersible pump sets confirming to IS 8034 anc motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V±10%, 3PH, 50 Hz, A.C. supply with cable guard, thrus carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. Submersible Pump set 100 mm dia (with Polypropylene/ Noryl Impeller) up to 20 stages 3 hp

Supplying, installation, testing and commissioning of electric driven Terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head

4 C 10 Sq.mm XLPE pvc sheathed Aluminium Armoud with aluminium conductor

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm nominal dia

80 mm nominal dia

25 mm nominal dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 150 mm nominal dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 150 mm nominal dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia

Supply and fixing of Pressure Gauge with needle valve & cock.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supply and fixing of Air Release Valve 25mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supply installation testing and commissioning of Double door Hose Box. .

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless steel(grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 ,20 mm nominal internal dia gun metal globe valve & nozzle.30m Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm nominal dia

80 mm nominal dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 150 mm nominal dia

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Junction Box

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable fire Monitor module complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supply installation testing and commissioning of ISI marked ABC 2 kg Capacity with ISI Certificate.

Supply installation testing and commissioning of ISI marked ABC 6 kg Capacity with ISI Certificate.

Supply installation testing and commissioning of CO2 4.5 Kg capacities. The extinguisher shall confirm to IS 2878 and have Certification mark and with Certificate.

Direct Driven Vane Axial Fan (TDC 800/C16/G/5-5V/33° (315))

Direct Driven Vane Axial fan with Smoke spill motor (TDC 800/C16/G/5-5V/33° (315))

Centrifugal Jet fan. The Jet fans are Rated for 300 Deg. C @ 2 Hrs. (IJC II 50)

Design,supplying, installation, testing and commissioning of audio visual in Auditorium as per the following specifications

SITC of POE+ Layer 2 Fully Manageable Network Switch consists of Fixed 1RU chassis 24 PoE 1G BaseT, 2 fixed RJ45/SFP+ combo (1G/10G), 2 fixed 1G/10G SFP+ uplink/VFL ports. Internal AC PSU (380 budget), includes country specific power cord, guides and 19" rack mount kit. Inclusive of stacking cable.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper

SITC Gigabit optical transceiver SFP. Supports monomode fiber over 1310nm wavelength nominal) with an LC connector. Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper

6 Port LIU Switch : SITC of 6 Port Loaded LIU with SC Unit for 6 SM fiber Single Mode fibres OS2 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 6 Fiber Capacity & 6 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Legrand/Panduit/RIT/Siemon)

24 Port LIU Switch : SITC of 24 Port Loaded LIU with SC Unit for 24 MM fiber Single Mode fibres SM OS2 (12 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter SM (Make:Legrand/Panduit/RIT/Siemon)

SITC of Fiber Duplex Patch Cords SC-LC SM Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon)

Supply and laying of 6 core Single mode OS2 Loose tube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. (Make:Legrand/Panduit/RIT/Siemon)

SITC of Fully Loaded 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon)

SITC of Straight LAN Patch Chord-2 Mtr (Make:Legrand/Panduit/RIT/Siemon)

SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon)

Supplying, delivery, installation, testing and commissioning of Flush mounted Cat 6 Information Single Outlet Box.on GI concealed Modular Switch Board including connections and making good the damages caused complete as required & as per Direction of Engineer-In-Charge.(Make:Legrand/Panduit/RIT/Siemon)

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

SITC of Fully Loaded 9U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 iPreffered Make-Legrand/Netrack/President/Valrack

Supply, delivery, installation & testing of Modular G.I. box 18 SWG Sheet ISI marked with Modular base & cover for1 or 2 module telephone/Data socket outlet..(Make- Legrand/Panduit/Ortronics)

78 mm X 140 mm X 50 mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preferred Make- AKG/NORPACK/Polycab/Dauphin 20 mm

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.The Cat6 Cable Should have the follwing specaifications furnished below. 1 Run CAT6 UTP Cable (for Network only . (Make:Legrand/Panduit/RIT/Siemon)

SITC of Telephone Tag Block): IP-65( weather proof). Preferred Make-Krone 20 Pair Krone BOX fully loaded without IPM

Wiring to Telephone Socket Outlet from Junction Box with 0.5 mm2 Four Pair Copper Conductor Telephone Wire run inside prelaid PVC Conduit complete including termination, testing etc complete as required and as per Direction of Engineer-In-Charge. 2 Pair (Make: Polycab/ Finolex/Anchor)

SITC of Single Phase Online 5 KVA UPS Preffered Make-Delta/Numeric/APC/Vertiv

SITC of 65 AH SMF Battery with 24 months Warranty

SITC of MS Battery Rack suitable for 15 to 20 UPS Battery installation

Supply, fitting, fixing, commissioning and testing of 16 Sq. MM Copper Conductor Multi strand PVC Sheilded FRLS Wire with suitable Copper LUGS for Battery Interconnection and suitable 25 Sq. mm copper wire of 2 length of 10 mtrs each for UPS to Battery excluding cable from PANEL to UPS and UPS to panel. Make- Polycab/Havells/KEI

Chemical Earthing

SITC of 5MP Fixed Lens Network Bullet Camera with following Technical Specifications; Preffered Make: Honeywell/Bosch/Hikvision/Pelco/Sony

SITC of 5MP Fixed Lens Network Dome Camera with following Technical Specifications; Preffered Make: Honeywell/Bosch/Hikvision/Pelco/Sony

SITC of 8 TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD

Supply, Installation, Testing and Commissioning of 55" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, Viewing Angle : 178° h/v, response time : 8ms, Display Colors- 16.7 Mill; Built in Speaker-10W+10W ; Inputs : HDMI x 2, DVI‐D, DisplayPort, Audio, RS‐232 Control, 100‐240 VAC @ 50/60Hz Power Supply, 24x7 Operation.; Preferred Make LG/Samsung/Panasonic

Outdoor Unit: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .Make - Hitachi / Daikin/ Mitsubishi Heavy 216 HP Outdoor Units

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fansection with low noise fan/dynamically balanced blower, multi speed motor, coil section with DX Coppercoil, electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, asrequired. The unit shall have automatic force shutdown provision in case off ireon receiving signal from BMS System. The cooling capacity of indoor unit will be at air in let conditions of 27Degree CD Band 19 Degree CWB temperature. 2.8 TR

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic mediapre-filter, fan section with low noise fan/dynamically balanced blower, multi speed motor, coilsection with DX coppercoil, electronice xpansionvalve, outercabinet, cord less remote control, drainpan, necessary accessories etc., suitable for operationon 230V±10%, 50Hz, single phase AC supply, complete as required.The unit shall have automatic force shutdown provision incase of fire on receiving signal from BMS system. The cooling capacity of indoor unit will be at air in let conditions of 27Degree C DB and 19 Degree C WB temperature. 0.8 TR

Supplying, installation, testing and commissioning of factory built floor mountedchilled water double skin typehorizontal/ vertical AHU made of 25 mm thick panels consisting of pre-plasticized galvanized sheet, and inner sheet of plain G.I. casing of thickness 0.8mm both inner & outer layer with with polyurethane foam (PUF) insulation factory injected between them by injection moduling machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling oil section with aluminium finned copper tubes(tubes thickness not less than 0.5mm)cooling coil of 6 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air pre filters, belt drive pakage with TEFC drive motor of efficiency class IE3 suitable for 415+10% volts, 50Hz, 3 phase ac supply suitabley designed for variable frequency drive applications, drain connections, stainless steel(18G) drain pan with PUF insulation, 150mm dia, dial type pressure gauges(2 nos) and industrial type thermometers (2 nos) at the inlet and outlet of coil. Auto purge valve wherever required. Necessary vibration isolation arrangement etc complete as per specificationand of following capacities, etc. AHU will have UV light to control mold & bacteria, reduce colds & flues germs are not re-circulated by the HVAC system, reduce smell & odors. Also, its Maintain a cleaner coil, improving cooling efficiency and reducing electricity costs and are more effective in humid climates than dry climates. Make : Zeco / Edgetech / VTS 4300 CMH

Supply & installation of Air Handling Expansion Kit for connection between Air Handling Unit & Outdoor Unit

Supply & Installation of Aluminium Extruded bottom loading HEPA Box with bottom operated arrangement, differential pressure measuring points along with Gel Seal Minipleate HEPA filter EU- 13 having Efficiency of 99.97% down to particle size of 0.3 Microns. It can be replaced from room side. Sizes :- 3m x 2m x 2m Make - Spectrum / Equivalent Laminar Air flow Unit with HEPA Filter

Supply,Installation,testingandcommissioningincludingvaccumiazationandNitrogentestingoffollowingnominalsizesofsoft/harddrawncopperrefrigerantpipingforVRV/VRFsystem,completewithfittings,withsuitableadjustableringtypehangersupports,jointing/brazingincludingaccessories,insulatedwithXPLEClass-Otubularinsulation/withClass-OclosedcellelastometricnitrilerubbertubularsleevessectionsofspecifiedthicknessasgivenbelowforSuctionandLiquidlines,allaccessoriesasperspecifications etc. as required : 12.7mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

15.86mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

15.86mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

19 mmdia(OD)(Harddrawn)withtubethickness1.2mmwith19mm thick insulation

28.58mmdia(OD)(Harddrawn)withtubethickness1.2mmwith19mm thick insulation

31.8mmdia(OD)(Harddrawn)withtubethickness1.62mmwith19mm thick insulation

Supply & Installation of Control wiring for AHU Indoor Unit to Outdoor Unit of 4 Core x 2.5 Sq. mm copper cable with suitable PVC conduit from Outdoor Units to Indoor Units

Supply & Installation of PVC drain pipe with Nitrile Rubber insulation along with necessary fittings as required 25 mm

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes , hangers, supports etc as per approved drawings and specifications of following sheet thickeness complete as required.. Duct construction as per SMACNA/ASHRAE/ISHRAE standard provides. Thickeness 22G (0.80 mm) Sheet

Thickness 24G (0.63 mm) sheet

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class"0") insulation on existing duct after applying two coats of cold setting adhesive. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 mm thick

Supply & installation of PPGI return air riser with filter (10 micron), Aluminium perforated grille, VCD etc.

Supply and Commissioning of AHU systems including additional referigernt R410A in all respect to complete the system as per site requirements

Supply & fixing of Pan type Humidifier with required thermostatic control for OT. Humidifiers made of stainless steel are clad in GPSP/Aluminium sheets and insulated with fibreglass. Units are available in both wall-mounted and floor-mounted designs. Water is heated to 60-70 degrees Celsius in the tank by a warm-up heater, thereby reducing the response time. Water is converted to vapour using tubular heating elements. These elements consists of helical coil of 80% Nickel 20% Chromium alloy resistance wire.

Linear Grilles

Diffuser (2 Feet x 2 Feet)

Volume Control Damper for Air Control

AUDITORIUM CHAIR

amoc 3 Seater Sofa With Genuine Leather Cover

Graphic Modular Table With Marine Ply Table Top and Wooden/Engineer wood Understructure Graphic (Centre Table Wooden )

CAFÉ TABLE Size - 1200 x 900 Material - Ms Frame with 25 mm Particle Board on Top Fixed type

CAFE CHAIR

Deck roller blind

CEMENT(3 Km radius)

SAND(25 Km radius)

Bricks(18 Km radius)

AGGREGATE(25 KM )

Add GST 18 %

Add Labour cess 1%

M/S RANG BAHADUR SINGH (BID ID -689639)