Construction of Open GYM in Naduvattom Junction at Malayattoor Neeleswaram Grama Panchayath

Construction of Open GYM

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

50.6.1.4 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

OD241746/2025-2026 Providing and Planting of Buffalo grass for Lawn in Ordinary soil including Breaking clods, Watering, Ramming and Sectioning of spoil bank etc., including all labour charges, etc., complete

16.79 Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

16.91.1 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

10.16.2 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

OD242472/2025-2026 Supplying and fixing machine finished granite stone sitting bench of 1.5 m length, slab thickness not less than 50 mm, 450 mm clear height from ground level, 450 mm wide sitting slab, 450 mm wide back rest including cost of conveying, loading, unloading,material and labour charges etc. complete as per the direction of departmental officers

OD241750/2025-2026 Designing and Fixing Inauguration/signage Board including cost of board, lettering, fixing, conveying etc all complete As per the Direction Of Departmental officers

OD242462/2025-2026 FUN RIDER- Providing and fixing Rider - FFE 023 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe- for MAIN FRAME, Minimum 32 NB GI BCLASS pipe for SEAT FRAME, Minimum 40 NB & 25 NB B CLASS GI BCLASS Pipe for HANDLE FRAME, Minimum 32NB & 25NB GI B-CLASS pipe with two handles for LEG REST, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for FOOT REST & SEAT REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

OD242464/2025-2026 ABB TRAINER- Providing and fixing ABB Trainer - FFE 025 (Make FUN PLAY )using, Minimum 80 NB GI B-class Pipe for MAIN FRAME, Minimum 32 NB GI Bclass Pipe for SIDE FRAME, Minimum 25 NB G.I. PIPES for INTERMEDIATE PIPE, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

OD242465/2025-2026 CYCLE- Providing and fixing Cycle - FFE 024 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

OD242466/2025-2026 ONE SEATING CUM 2 STANDING TWISTER- Providing and fixing ONE SEATING CUM 2 STANDING TWISTER - FFE 019D (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for MAIN FRAME, Minimum 25 NB GI BCLASS Pipe for HANDLE FRAME, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for TWISTER DISC, Minimum 25 NB & 20 NB GI Bclass Pipe for SEATING FRAME, Minimum 80 NB GI B-class Pipe for SEATING FRAME STAND, Minimum 80 NB GI B-CLASS Pipe for TWISTER STAND, Minimum 25 NB GI B-CLASS Pipe for TWISTER HANDLE FRAME, LLDP Plastic- TWISTER DISC, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

OD242467/2025-2026 CHEST PRESS CUM SHOULDER PRESS- Providing and fixing Chest press cum shoulder press - FFE 007 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for CENTER FRAME, Minimum 40 NB & 32 NB GI B-CLASS Pipe for MAIN FRAME, Minimum 32 NB & 25 NB GI B-CLASS Pipe for HANDLE FRAME, Minimum 32 NB & 25 NB & 40 NB GI BCLASS Pipe for CONNECTING PIPE, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for SEAT & BACK REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge