DEPOSIT Construction of Pump house and Allied works RWSS to Thrikkaruva Grama Panchayath in Thinavila Colony

Amount

Construction of a Pump house 2mx2m, Bleaching powder room1mx1.2m and Chlorine tank facility

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

50.6.1.4:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.1.2:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating less than 275 gm/m2

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

OD130432/2022-2023:Wiring the pump house and Providing 4 nos light point, and 1 No Fan point and one socket etc wiring the pump house using best quality copper wire with pvc pipe and fitting switches, sockets etc in two switch board and supply and fitting 2 nos. 20 w CFL bulbs, 2 nos. tube set, 1 no. sealing fan best quality as per IE rules.

OD130433/2022-2023:Providing chlorination arrangements to the tube well pump house by supplying and fixing 2 nos of PVC tanks with capacity 500 Ltr &300Ltr with the platform out side suitable to bleaching powder solution connecting to the 80 mm GI pumping main near the well including cost of all materials , labour charges etc complete as per the instruction of officer in charge

Automation arrangements

OD130427/2022-2023:Installation charge for sub pump controller kit.

OD130428/2022-2023:Supply of SIM , SIM kit and including plan for 1 year

OD130429/2022-2023:Supply of M POWER module for mobile starter for motor.

OD130430/2022-2023:SUPPLY OF MU-G20 fully automatic star delta starter for automation .

Supply and errection of Pump set

OD130419/2022-2023: Supply, erection, testing and commissioning of Brand new Submersible pump set with all accessories having ISI mark with suitable motor having 35000 LPH sufficient discharge in accordance with the yield of the tube well and against a total head as instructed by the deptl officers, with bronze impellers, SS316 shaft etc working in 3 ph AC main as per IS specification with minimum efficiency of 70% . The rate quoted inclusive of 5m , 80 mm GI B class pipe and specials, 5m 4 sq.mm cable , fully automatic star delta starter of approved manufacturers , interconnection of outlet with existing distribution line using suitable specials, earthing by using suitable copper wire/plate, supply and fixing standard type floor mounted panel board, supplying copper cable of required length and size, providing cable connection from pannel board to starter and starter to motor etc, supply<br>and fixing suitable type CI D/Sluice valve , reflux valve, pressure gauges, power capacitor, single phase and dry<br>running preventors, earthing main switch board with all units as per IE Rules, hire for tools, supplying ,fabricating and<br>fitting meter box as per KSE I rules for fixing the meter & fuse unit of KSEB etc complete as per the direction of<br>departmental officers.

OD148071/2022-2023:Supply of Supply of 80 mm uPVC column pipe including coupling

OD130422/2022-2023: Charges for supplying best quality 3 core 4 sq mm flat copper cable for erection work

OD130424/2022-2023:Fabrcating and supplying 80 mm GI Pumping main from top of the tube well to 110 mm PVC distribution line including providing Tee joint,3 Nos of 80 mm G I bent ,5 Nos MS flange for fitting control valves and foundation to the top of the well mouth using 80 mm GI pipe suitable to proper horizontal alignment, welding together to water tight joint including earth work excavation cost of all materials , labour charges ,hire charges of welding machine, cutting / grinding machine etc

100.98.512:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.0, Size 80mm.

100.31.1.1:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 80mm diameter, Class I.

LIJEESH V

Bidder Name

S.Shaji

LIJEESH V