8456/E8 SPL REPAIR TO LT UG CABLE, EARTHING, LA AND OTHER ALLIED WORKS AT SASF AND PROVISION OF 150 X CEILING FANS, 50 X EXHAUST FAN AND HEAVY DUTY DESERT COOLERS, WATER COOLER AT SHAHJAHNPUR CANTT UNDER GE (EAST) BAREILLY

Amount

Excavation in trenches n. exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying under ground LT XLPE cable and getting soft/loose soil complete.

M&L Returning , filling in including spreading, levelling, watering and well ramming in laying not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

M&L Removing excavated material (soils) to a distance not exceeding 50 m and depositing whare directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Material and labour for river fine sand, washed and screened dry for caushioning to under ground cable in trenches below and around under ground cable including spreading and levelling punning complete.

M&L for laying bricks, sub class 'B' for protection of cable, in trenches, laid in dry flat across the cable with length of whole bricks complete all as specified and directed.

Taking down/out old defective cable from trench/floor/road/wall/pipe /pole service connection of any size testing and checking of cable of any material complete all as specified & directed.

Supply and laying XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) with stranded aluminum conductor 1100 Volts grade of size 50 Sqmm 3.5 core complete all as specified & directed.

All as per item no .7 size here in before but 35 Sqmm 3.5 core .

All as per item no.7 size here in before but 25 Sqmm 3.5 core .

All as per item no.7 size here in before but 16 Sqmm 3.5 core .

All as per item no.7 size here in before but 10 Sqmm 4 core .

All as per above item No.7 same as 10 sqmm 2 core

S & F steel tubing GI Light grade 32 mm bore for fixing of tapping of incoming and outgoing point complete all as specified and directed.

S & F steel tubing GI Light grade 40mm bore for fixing of tapping of incoming and outgoing point complete all as specified and directed.

S & F in replacement of GI tubing light grade 80mm nominal bore for cable protection fixed with clamps of M.S. Flat iron 25x3mm, GI nuts, bolts and washers to poles/under floor/under roads/alongwith walls including two coats of aluminium paint over a coat of red oxide primer on clamps complete including taking up of old UNSV GI tubing complete all as specified and directed by Engr-in-Charge.

M & L for Boring under Road / PCC by using manual tool for inserting, including GI pipe of 80mm size for protection of cable complete all as specified and as directed by the Engineer-In-Charge.

M & L for Cutting of existing RCC Floor/PCC/Tiles for electrical cable and supply and fix tube, 'light grade, galvanised 25mm dia, necessary connection to TPN DB from LT control panel and making good to the disturbed surfaces of floor from RCC including to match the existing type etc all as directed

Supply and fix Junction box cover made of PVC super fine quality fixed to pole connector block din rail suitable size of aluminium bus bar locking arrangement complete all as specified and as directed.

M & L Cupper wire with Two core 2.5 sqmm PVC insulated 1100 volts grade connected from Security light to DB/main board with PVC conduit complete all as specified and as directed.

Taking down/out old defective rusted iron pole from LT line connection of any size testing and checking of cable of any material complete all as specified & directed.

Supply and fix in replacement Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0metres long) complete all as specified and as directed

M&L Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate for coping around poles, including necessary form work finishing even and smooth complite all as specified and directed .

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in pole/stay/ plinth etc in foundation filling completed all as directed by Engr-in-Charge.

M&L for jointing and testing of straight through termination joint (heat shrinkable) suitable for 3.5 core (Earthed) underground XLPE cable of size 10 to 50 sq mm including taking down existing unserviceable joint complete all as specified and as directed.

Supply and fix in replacement of single pointed Air termination aluminium rod 12 mm dia 300mm long fix with saddle all as specified and directed by Engr-in-Charge.

Supply and Fix in replacement of earthing strip GI 25 x 3.15 mm complete with saddle and fixing screws etc. For roof conductors and down conductors above ground up to test point to Electrical equipment including taking up of old UNSV earthing strip complete all as specified and directed by Engr-in-Charge.

M&Lfor earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick, buried directly in ground, vertically to a depth not less than 2.25 mtr deep below ground level with top edge of the earth plate at depth not less than 1.5 mtr below ground level earth plate surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, earth lead GI strip 32x6mm dia by means of bolts, nuts, check-nuts and washers of galvanized iron and thimbles and of earth wire protected by galvanized iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh complete including excavation and earth work, PCC chamber and cover in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in lieu of CI cover and frame etc all as specified and shown in electrical plate No. 3 of SSR-2009 (Part-I).

Material & Labour for supply,installing,testing & commissioning of factory made LT panel outdoor type for LT distribution switch gear and control gear,floor mounted ,cubical type modular compartment, dust and vermin proof with neoprene gasket fabricated out of CRCA sheet of thick ness not less than 3.15 mm (CPRI Approved) complete with bus bar chamber & cupper Bus bar of four wire system 415 volt with heat shrinkable insulator sleeve suitable for 315 A for phases and for neutral having openable front and rear shutters with suitable locking arrangement epoxy powder spray painted with one coat primercomplete including PCC 1:2:4 type B-1 using 20 mm graded stone agregate foundation raised base angle iron size 50mm x50mmx6mm thick 60cm up and 60cm ground level complete all as specified and directed by the Engr in Charge of the following components:- Contractor should arrange factory visit to Engr-in-charge at own arrangement for LT Pannel manufacturing.

(a) INCOMING :- (i) Supply and fix 4 Pole MCCB ,200 Amp 50 Hz 415 V, With Thermal based Release type Capacity 35 KA complete all as specified and directed =01 Nos (b) OUTGOING :- (i) Supply and fix 4 Pole MCCB ,100 Amp 50 Hz 415 V, With Thermal based Release type Capacity 25 KA complete all as specified and directed =04 Nos (c) Supply and fix R Y B Phase LED based indicator lamp sets comprising of three colours complete all as specified and directed =01 set (d). Ammeter 0 - 400 Amps, Digital display, flush mounted 3 phase 4 wire with slector switch including CTs of required capacity =01 Set (e) Voltmeter 0 - 600 Volts, Digital display, flush mounted 3 phase 4 wire with slector switch - 01 set. (g) Supply and fix time switches 415 V three Phase of 20 Amp rating with contactor fitted inside steel enclosure.

Supply and fix testing and commissioning Out door type Bus bar made out of MS CRCA sheet 2mm thick of size 0.60 Mtrx0.60mtrx0.30 mtr consisting aluminium Bus Bar of rating 200 Amps working 4 wire system 415 volt mounted on various insulator with cable earth alleys including steel flexible pipe as per required length at site with new aluminium lugs of suitable size including making connection properly of existing cables of any size/type for existing new incoming and outgoing cables complete all as specified and as directed by Engr-In-Charge. Note : Bus Bar mounting stand made out of angle iron of size 50mm x50mm x 6mm, 600 mm high and size suitable to mount the panel including foundation of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with and including excavation and earth work in any type of soil complete.Contractor should arrange factory visit to Engr-in-charge at own arrangement for LT Pannel manufacturing.

Supply, installation, commis-sioning of Water cooler fully stainless steel, electric driven single phase having approx storage 80 litre and nominal cooling capacity of 40 litre per hour all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 1KVA.

M & L for Point wiring in concealed PVC conduit using stranded copper conductor cable of size 2.5 Sqmm, PVC insulated unsheathed FRLS cable complete with all fittings and accessories but using existing sunken cast iron or pressed steel terminal box for mounting of switches, sockets, fan regulators etc but providing new cover 3mm thick laminated,(Hylem) sheet top cover fastened with chromium plated screws and 2.5 Sqmm PVC insulated stranded copper conductor FRLS cable as continues earth wire connected to common earth dolly all as directed and as specified for One 3 pin socket outlet 15 Amp on independent board for the following :- NOTE: for wiring in ceiling portion conduit shall be fixed with surface of ceiling/with trusses etc.

S &F switch piano flush type polycarbonate SP one way 15 Amps complete all as specified and directed

S&F socket out let 3 pin 5/15 Amp multipurpose, flush type 240 volt complete.

S & F and installation of desert cooler heavy duty electric driven product dimension 960x570x1570 tank water capacity 120 ltr fitted with heavy duty fan & motor RPM 1350(single phase), having nominal air flow capacity of 10000 M3/ per hour,fan blade size-24 inch ,honeycomb cooling pad including opening door three side with tulu pump,wheel lcoking arrangement and other accessories complete all as specified and as directed by Engr-In-Charge

Material and Labour for Point wiring with 1.5 Sq mm copper conductor single core PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC conduit concealed and conduit accessories of suitable dia medium grade and pressed steel terminal boxes suitable for swiches size and duly painted with red oxide metal primer including fixing/grouting sunken/ surface as per site requirement covered with suitable for fixing switches / sockets/ regulators including fixing all accessories etc including running up of 1.5 Sq mm copper conductor PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for the following :- (a). One light/fan point controlled by one switch

S & F Switch piano type single pole one way flush type 5 Amps capacity 230 volts.

Supply & fix 1200mm Glaze BLDC ceiling fan (white) complete with remote control and electronic type regulator and accessories 230 V,1200 mm sweep. 5 star rated all as per specified and as directed by Engr -In-Charge

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers all as per specified and as directed by Engr -In-Charge

Cutting of wall for exhaust fan of any size and sweep and necessary fitting such as nut bolt and washers & Fastner and to make as per existing colour to match the wall all as per specified and as directed by Engr-In-Charge

M/S WASEEM KHAN CONTRACTOR (BID ID -3458877)

M/S CHAUHAN ELECTRIC WORKS (BID ID -3461322)

Shikhar ji Enterprises (BID ID -3461491)

M/S SHAHABUDDIN AND SONS (BID ID -3457998)

VINYAK TRADERS (BID ID -3460944)