Construction of CAD works for FIS Kasol in Tehsil Sadar District Bilaspur (SH Laying jointing and testing in trenches HDPE pipes for distribution system and construction of 39 Nos field outlet assembly).

Amount

Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work, jumper work, blasting work in soft/hard rock, chiseling wedging out of rock where blasting is prohibited saturated soil stacking the excavated soil in all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm layers, when required into sides of foundation etc. consolidating each deposited layer by ramming and watering and then deposing of all surplus excavated earth as directed within all leads and lifts.

Laying jointing and testing in trenches HDPE pipe of following diameter and class as per IS: 4984-2016 grade PE-80 and jointing the pipes through push type compression joints by hydraulically operated machine complete with butt (heat) fusion welded joints with necessary fittings such as bends, tees, reducers etc. fabricated in accordance with IS: 8360 and IS: 8008 with latest amendements and shall be provided as per site conditions. The flanging of the pipes shall be made as and where required conforming to IS: code 8008 and 7634, stud ends shall be fussion welded on pipes & flanges shall be provided with slip on covered by epoxy coating / plastic powder. The flanges should be conform to ANSI B 16.5 with necessary nuts and bolts (Earth work in trenches to be measured and paid for separately) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

90mm dia HDPE pipe Pe-80 PN-4

110 mm dia HDPE pipe Pe-80 PN-4

125 mm dia HDPE pipe Pe-80 PN-4

140 mm dia HDPE pipe Pe-80 PN-4

160 mm dia HDPE pipe Pe-80 PN-4

180 mm dia HDPE pipe Pe-80 PN-4

Providing and laying cement concrete 1:4:8 (1cement:4sand:8 graded stone agg. 40mmnominal size) and curing complete excluding the cost of form work in foundation and plinth in all depths and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1.1.5:3 (1cmeent: 1:5 sand: 3 graded stone agg.20mm nominal size finishing and curing complete excluding the cost of form work for RCC work in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and laying pre-cast slab in nominal cement concrete 1:1.5:3 and curing complete excluding the cost of form work in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centering below supporting floor two ceiling not exceeding 4 mtr and removal of the same for in-situ reinforced concrete and plain concrete work in :-

Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like and to the entire satisfaction of the Engineer-in-charge.

Boulder filling at bottom in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Fitting and accessories

110mmdia PN-4.0/5.0/6.0/ 8.0 HDPE pipe

110mmdia PN-6 HDPE pipe end

110mmdia PN-6 HDPE 90 degree bends

110mmdia PN-6 HDPE QC pump connector

Providing mild/tor steel reinforcement for RCC work including bending binding and placing in position complete in all depths and heights and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing in position RCC pipe of following dia, class and length for outlets and to the entire satisfaction of the Engineer-in-charge.

RCC pipe of 900mm dia NP-2.0

RCC pipe of 350mm dia NP2.0

Providing and fixing of Cast Iron Sluice valve Kirloskar/Leader make of 80mm dia with hand wheel as per IS: 14846-2000 class-PN-1 including brass spindle as per 2906-1984 complete with bolts, nuts, rubber insertion etc. (The tail piece if required shall be measured and paid for separately) and to the entire satisfaction of the Engineer-in-charge.

Steel work welded in built up section including cutting, hoisting fixing in position and applying a priming coat of red lead paint in gratings framed guard, bars, ladders, railing brackets and similar works and to the entire satisfaction of the Engineer-in-charge.

Miscellanious for locking arrangement and other accessories etc and to the entire satisfaction of the Engineer-in-charge.

SHIV KANT PRASHAR

Basant Lal

Sh.Rattan Lal