ADDN ALTN AND SPL REPAIR OF SELECTED OLD MD ACCN AT DHANUSH MARG VADODARA UNDER GE (A) VADODARA

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level).

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for drain etc.

Demolition of stone slabs and tiles of any description or thickness laid in floors & fixed on wall, laid bedded & pointed in any mortar.

Dismantling wrought iron or mild steel work of any description not otherwise provided for steel gate and similar work

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each

Taking down chowkats or frame with shutter (without taking off shutter from the frame) exc 1.5 Sq m but n.exc 4.00 Sq m each

Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge.

Dismantling of water storage tank of capacity 500 ltrs and above upto1000 ltrs capacity.

Dismantling cast iron pipes, jointed in cement mortar for 100 mm bore including fittings in any location and position

Dismantling cast iron pipes, jointed in cement mortar for 75 mm bore including fittings in any location and position

M & L for 75 mm thick PCC 1:3:6 mix type C1 using 20 mm graded stone aggregate as in plinth protection and paving finishing concrerte surface even and smooth without using extra cement.

M & L for brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6

Used and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed.

All as per Item No 21 above but 5mm dia and over upto and including 10 mm dia for stirrups, spacers and binders etc

M & L for reinforced cement concrete (Nominal Mix) 1:1.5:3 type A-0 using 12.5mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed

M & L for reinforced cement concrete (Nominal Mix) 1:1.5:3 type A-0 using 12.5mm graded stone aggregate as Beams, cantilevers, bressummers, lintels over 1.5m span etc all as specified and as directed

M & L for reinforced cement concrete (Nominal Mix) 1:1.5:3 type A-0 using 12.5mm graded stone aggregate as in Chajjas etc all as specified and as directed

M & L for Cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) as in haunching, roof kerbs or mud stops, rounded or chamfered on edges.

Supply and fix in repairs for providing precast cement concrete type B0 (1:2:4) using 12.5mm graded stone aggregate set in cement mortar 1:4 as in louvers and jallies 40mm thick including all mouldings

M&L for preparation of reinforcement and apply two coats of corrosion resisting rust remover suitable time to be provided between two coats according to manufacturer's instructions to resist further detoriation of reinforcement etc complete all as specified and as directed ( Total surface area of conc to be measured )

M&L for apply Epoxy Bonding agent (2 part solvent free epox based bonding agent) to old concrete surface/mortar before applying the plastering to the surface complete all as specified and as directed

Providing and laying super fluid microconcrete -roffe crec repairs (or equivalent as specified in the list of brand names) in beam bottoms, columns, slabs etc, including mixing with 5mm to 10mm size aggregates, waterproof ply wood/steel plate shuttering, pouring, temping, consolidating, curing etc complete as per manufacturer's specifications and consultants Instructions. Note :- This item shall be paid on the basis of actual consumption of Micro concrete.

M & L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia, roof bands etc and making good with PCC (1:11/2:3) type A0 (using 12.5 mm graded stone aggregate) in any slab and in any position finished the surface even and smooth with out using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement) if required complete and applying three coats of white wash/two coats of cement base paint to match with the existing surface as directed by the Engr- in -Charge .

Roughning of old unserviceable PCC floor surface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile

M&L for Vitrified tiles coloured 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and match with and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 all as specified and directed

M&L for Vitrified tiles coloured 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including backing coat 10 mm thick in CM 1:3 all as specified and directed

M&L for non skid colour ceramic tile 7 to 8 mm thick joint free area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm , as in floors etc set over and including high performence adhesive manufactured by Somani ezifix tile adhesive or equivalent mixed in cement as per manufacturer's instructions and jointed with polymer modified cementetious grout manufactured by Somani ezy grout or equivalnet of pigment matching to tile color with and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 (Tile pattern and design may be as suggested by Engineer-in-Charge)

M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including high performence adhesive manufactured by Somani ezifix tile adhesive or equivalent mixed in cement as per manufacturer's instruction and jointed with polymer modified cementetious grout manufactured by Somani ezy grout or equivalnet of pigment matching to tile color with and including 10mm thick rendering for screed bed on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles (Tile pattern and decoration may be as suggested by Engineer-in-charge).

M & L for 18-20mm thick Granite (of any type) work (table rubbed and polished) fixed as in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. all as specifed and as directed. (Note : Type and source of granite as approved by GE)

M & L for 16 to 18 mm thick machine cut green marbel stone in single piece fixed in riser of steps, skirting, dado, window (Jambs/Cills), and pillar laid over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with and including 10 mm thick plastering in cement mortar 1 : 4 complete all as specified

M & L for 16 to 18 mm thick machine cut green marbel stone laid as in flooring, in steps in single piece over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with and including 15 mm thick plastering in cement mortar 1 : 6 complete all as specified

S&F in repairs 1.25mm thick mild steel sheeting in wall clading, steel gates and similar work cut to size, holes punched; including necessary application of welding to frame and cutting to old rusted steel sheet all as specified and as directed

S&F in repairs framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming to IS Fe-290 (Gde E165) complete all as specified and as directed

M&L for necessary welding in repairs to steel surface not exc 6 mm thick and area n.exc 2.5 Cm in length

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

M&L rendering 15 mm thick in two layer 10 mm & 5 mm on fair faces of brick work or concrete sur-faces of wall 05 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 Note :- WPC will be measured and paid separately.

M&L for 15 mm thick rendering or plastering work in CM (1:4) in isolated widths or in width not forming part of general plastering such as in bands, sunk panels cornices skiring drip moulds and similar work exc 15 cm but n.exc 30 cm in width or girth including cutting to edges

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of ceiling in cement mortar 1:3 finished even and smooth (without using extra cement)

Supply only Integral water proofing compound all as specified and directed.

M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of 1 to 2mm average thickness Birla/ J.K wall care putty and one coat of cement base primer. Note : Putty shall be measured and paid separately under relevant Item of BOQ

M & L for complete removal of old existing treatment by scrapping and or rubbing of wall and applying two coats of oil bound distamper over a coat of 1 to 2mm average thickness Birla/ equivalent wall care putty and one coat of primer. Note : Putty shall be measured and paid separately under relevant Item of BOQ

M&L preparing new/old plastered surfaces of wall and applying 1 to 2 mm thick layer of Birla/J K Wall care Putty smooth & even finished all as specified and directed. .

M & L for preparing new plastered surfaces of wall and applying two coats cement base paint over a coat of primer on external wall.

M & L for preparing old decorated surfaces of wall and applying two coats of cement base paint on external wall

M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash.

M & L for preparing old plastered surfaces of ceiling and applying two coats of white wash on ceiling to match with the existing surfaces.

Taking down and refixing in the same opening of shutter of any description n.exc 1 Sqm each

Taking down and refixing of shutter of any description exc. 1 sqm and n.exc. 2 sqm each in same opening.

M&L for 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), surface finish with 6mm thick external teak wood lipping fixed with nails, color and pattern as approved by Engineer-in-Charge/GE.

S & F factory made 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats.

S&F Powder coated (minimum thickness of powder coating 50 micron) aluminium frame section (minimum thickness 1.50 mm for bottom and 1.20mm for top and sides for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Powder coated (minimum thickness of powder coating 50 micron) aluminium window/ventilator shutters section (minimum thickness 1.50 mm for bottom and 1.20mm for top and sides) , side hung/sliding type aluminium sections including necessary joining cleats, sash bars, glazing clips rubber neoprene packing, anodised aluminium snap beading, screws and grill etc as per manufactures instruction & trade pactee.

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips, all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S & F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolt, if required hooks(stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 310-O or Fe 410-O.

M & L Cement concrete type C1, 1:3:6 (using 20 mm graded stone aggregate) as in coping, bed plate for hold fast etc. including necessary form work if required.

M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/PVC door frame with screw complete all as specified and directed.

S & F 200mm long aluminium anodised barrel tower bolt of extruded section and fixed

S & F in repairs 200mm long Aluminium anodised barrel tower bolt of extruded section and fixed

S & F 150 mm size extruded aluminium alloy handles, febricated type anodised

S & F 250 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters

S & F 2nd class HW small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each

S & F solid PVC door frame of size 50mmx47mm made out of 5mm prelam PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing and matching with door shutter shade. The door frame shall be tied to the wall using 75/100mm long MS screw and PVC fasteners as directed .

S & F 30mm thick factory made both sides prelam panel PVC door shutter consisting of frame made out of MS tube of 19 gauges thickness and size 19mm x 19mm for stiles, top and bottom rails, MS frame shall have a coat of steel primer of approved make and manufacture. MS frame shall be covered with 5mm thick heat moulded prelam PVC C channel size 30mm thickness, 70mm width, out of which 50mm should be flat and 20mm shall be tappered in 45 degree < on either sides forming stiles and 5mm, 95mm wide prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide. prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tappered on both sides to form lock rail. Top rail, bottom rail and lock rail shall be provided either sides of the panel 10mm (5mm x2) thick 20mm wide cross PVC sheet shall be provided as gap insert for top rail, and bottom rail paneling of 5mm thick both side prelam PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with 7mm (5mm+2mm) thick 15mm wide. PVC sheet beading on inner side and jointed together with solvant cement adhesive, an additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of C channel using PVC solvant adhesive etc. complete all as specified and directed.

S & F 125 mm aluminium alloy handles, extruded type anodised all as specified.

S & F 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S & F tubular curtain rails 25mm dia of stainless steel 202 grade complete all as specified directed

S & F in repairs stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE) as directed

S&F CP corner glass shelf of size 300mm x 300mm with bracket Make Prayag or equivalent make.

S&F in repair CP towel rail 600mm long with lower hangers

S & F in repair CP Towel ring brass chromuim plated all as specified.

S & F 25 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on one side and the other side covered with decorative choice lamination (factory laminated) face veneer with lipping/ frame to match

M&L Teak wood lipping, 3 to 6 mm thick fixed with nail for 18/19 mm thick block board

S & F in repairs 18/19mm thick veneered particle board interior grade, solid core, general purposes type with face veneers of type 'BB' fixed with screws to timber frame work complete all as specfied and as directed.

S & F pressed steel doors frame (thickness of MS sheet 1.25mm) with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete and stainless steel hinges will be measured and paid saperately under respective items.

S & F pressed steel doors frame with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete and stainless steel hinges will be measured and paid saperately under respective items.

M & L for cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in filling hollow portion of pressed steel door frame

M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M & L for preparing old steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint.

M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M & L for preparing old wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint to match the existing surfaces.

S&F glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S & F in repairs Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm including suitable waste coupling and waste pipe of size 32mm bore.

Supply & Fix in repairs of stainless steel wall mounted plate rack of size 880x880X 220 mm and thickness of sheet not less than 0.50mm with provn for keeping plates and other crockery fixed with screw and rawal plug etc on wall complete all as specified and as directed

S & F in repairs Chromium plated soap dish heavy duty fixed with brass screw complete all as directed. Make Prayag Cat Part No BA-05 or equivelent make.

S & F 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Refixing 15mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc)

S & F 20mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Refixing 20mm bore steel tubibg and connections in new or old position (Walls, ceiling, floors, etc)

S & F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Refixing 25mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc)

S&F 40 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe

S & F 500 Ltrs Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S & F 1000 Ltrs Rotational moulded polyethylene water storage tanks three layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

Disconnecting existing tanks of capacity exc 500 ltrs but n exc 1000 ltrs capacity, setting aside (or lowering if required) for repairs cleaning etc and hoisting if required reconnecting and re fixing in position. Cleaning and removing of all scale and dirt etc from tanks and from mouths of circulating pipes etc. including all necessary fittings if required complete all as specified and as direct

S & F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed

S & F in repairs Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complete screwed for iron pipe or brass ferrule and fixed

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including taking out old pipe any type all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including taking out old pipe any type all as specified and as directed.

S & F in repairs 110mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F in repairs 110mm bore PVC (SWR) bends any radius with oval access door all as specified and as directed.

S & F in repairs 110mm bore PVC (SWR) shoe

S & F in repairs 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal or with parallel branches with access door all as specified and as directed

S & F 110mm PVC (SWR) vent cowl all as specified and as directed

S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed.

S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed.

S & F 110mm PVC (SWR) junction single, (Single T, 'Y' type) equal or unequal all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including taking out old pipe any type all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches including taking out old pipe any type all as specified and as directed.

S & F in repairs 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F in repairs 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed.

S & F 75mm PVC (SWR) junction single, (Single, 'Y' type T) equal or unequal all as specified and as directed.

S & F 75mm PVC (SWR) vent cowl all as specified and as directed

S & F in repair 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent all as specified and as directed.

S & F in repair SGSW gully trap of size 150x100mm jointing to waste pipe fixed to cement concrete type B1 1:2:4 for 75mm bore all as specified and as directed.

S & F stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed

S &F repairs vitrous china wash down water closet pan (pedestal pettern) white including white plastic water closet seat cover and back with flat bottom and cover mild steel chromium plated and aluminium anodised hinging device (excluding flushing cistern and flush pipe) but including fixing bolt and necessary connection with existing pipes complete all sepecified and directed.

Supply and fixed in repairs PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band 32mm complete all as specified.

S & F in repair CP wall mixer three in one system for mixing hot and cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed.

S&F of CP Sink mixer with swinging casted spout (wall mounted model) with connecting legs & wall flanges

S & F in repairs 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule

S&F bib cock 2 way with wall flange

S & F in repairs stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed

S & F as in repairs 125mm dia chromium plated shower rose with swivel joints with 300mm long CP arms including fixing to GI union complete

S&F as in repairs Toilet paper holder with flap recessed type (stainless steel) fixed with chromium plated screws & PVC cleats complete Make : Prayag (Cat Part No BA-88) or equivalent make

S & F in repair of chromium plated Health faucet 15mm dia 1 mtr long tube acrylic type complete wall hanging arrangement complete all as directed.

S & F toilet jet sprey made out of stainless steel flexible tube of 15 mm dia all as specified and directed.

S & F in repairs 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S&F in repair vitreous china Wash hand basin, white, flat back size 550x400 mm except taps, CP waste coupling but incl brackets cutting for and pinning in ends of brackets, or erected stand all as specified.

S&F in repair vitreous china Wash hand basin, white, bowel type size 550x400 mm except taps, CP waste coupling but incl brackets cutting for and pinning in ends of brackets, or erected stand all as specified.

Supply and fixing CP Centre hole Wash Basin mixer (Swan Neck) three in One 15 mm bore pipe complet all as specified.

S & F 32 mm dia stainless steel waste coupling for wash hand basin in repairs all as specified and directed.

S & F SS bottle trap for wash hand basin all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm

Removing existing water profing membrane treatment /tarfelt roof treatment except concrete padding roughening of concrete surface cleaning and washing down the surfaces with water and removing debrish/rubbish material to a distance exc. 1.5 Km but not exc. 5.0 KM out side MD land complete all as specified and directed. Note : This item shall be carried out at places where demolition of PCC padding is not involved . Wherever demolition of PCC padding under the existing water proofing membrane /tarfelt roof treatment is involved the taking down of the roof treatment membrane etc shall be measured and deemed included with demolition of PCC.

M&L PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPC @ 2% by wt of cement finished surface even and smooth without using extra cement for laying of WPT all as specified and directed. (WPC will be measured and paid separately). thickness nexc 50 mm

M&L for 10 mm thick plaster on roof surface with CM 1:3 mixed with water proofing compound @3% by weight of cement. Plaster will be carried out such a manner when PCC padding is green plaster surface should be even and smooth without using extra cement all as directed. Note . (WPC will be measured and paid separately).

M&L for water Proofing treatment to top of roof slabs by applying one coat of bituminious oil based/polymerized primer confirming to IS-3384 @ 0.30 Ltrs/Sqm, and laying actetic polypropylene (APP) modified membrane pre fabricated (centre core) with thermal insulation with polythene finish on upper side of membrane, reinforced with non woven polyester, of minimum weight not less than 3.50 Kg/Sqm, 3 mm thick (minimum) laid by torch application method with minimum 75 mm side overlaps and minium 100 mm end overlaps and applying two coats of aluminium paint @ 0.20 ltr//Sqm over APP membrane complete all as specified and directed by Engr-In-Charge

M&L for water Proofing treatment to top of roof slabs by applying one coat of bituminious oil based/polymerized primer confirming to IS-3384 @ 0.30 Ltrs/Sqm, and laying actetic polypropylene (APP) modified membrane pre fabricated, reinforced with non woven polyester (centre core) with thermal insulation with polythene finish on upper side of membrane, of minimum weight not less than 3.50 Kg/Sqm 3 mm thick (minimum) laid by torch application method with minimum 75 mm side overlaps and minimum 100 mm end overlaps a complete all as specified and directed by Engr-In-Charge

S&F Cutting out cracks to V-section in existing roof or terracing n.exc 15 cm girth, cleaning out and filling solidly with hot mixtuire of bitumin and clean dry sand 1:1 (by weight) or with crack 'X' Mke Dr. Fixit or equivalent

M & L for Cement concrete tiles 25cm x 25cm x 22mm thick, m a c h i n e pressed; set jointed and pointed in neat cement slurry with WPC @ 3% by wt of cement in floors/roof top laid over and including 15mm thick cement screed in cm 1:6 complete all as specified and directed (WPC will be measured and paid separately).

All as per Item No 152.00 above but except tiles complete all as specified and directed (WPC will be measured and paid separately).

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cable/pipe etc or for shaft, walls, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan & n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified & directed.

M&L for concrete bed to drain pipes 100mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including demolition of damaged concrete complete

M & L for cutting into exising manholes for connecting new drains, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished & reforming benching as required for internal dia of pipe 150mm.

Returning, filling in excavated approved soil spreading, levelling, watering and well ramming in layer n exc 25mm each in soft/loose soil complete

Removing of excavation material n exc 50 mtr and deposited where directed at a level n exc 1.50 mtr above the starting point in soft/loose soil complete.

M&L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in benching of man hole and coping including form work complete

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms mould stopped ends.

M&L for Providing precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone agg in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to matchcomplete all as specified and directed. (reinforcement shall be measured and paid separately)

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, Cooler Stand and similar work con- forming to Fe.290.Gde-E-165 all as specified and directed.

S&F Structural Steel as in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete conforming to Fe.290.Gde-E-165 all as specified and directed.

M&L for 15 mm thick plaster in sunken portion with CM 1:3 mixed with water proofing compound @2% by weight of cement plaster surface should be even and smooth without using extra cement all as directed. Note . (WPC will be measured and paid separately).

M & L for 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded aggregate) with water proofing compound @ 2% by weight of cement for laying floor tiles. Note (WPC will be measured and paid separately).

Providing and fixing factory made 18(+0.7mm) thick PVC sheet one sided pre laminated sheet cabinet shutter. 18 mm(+0.7mm) thick sheet shutter of density 600 kg/m3 bent at 90o and finished all edges at all level for making edges, Lipping/bending or 0.5 mm thk PVC sheet lipping at all four edges using bonding tape etc complete all as per directions of enginer in Charge, Manufacturers's speciifcations

M&L for Pre polished chequred cement concrete tiles of size 30cm x 30cm x 25mm thick set and jointed and pointed in neat cement slurry in floor with grey cement and pigment over and including 15mm thick screed bed or bedding layer in cement mortor 1:4 complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20 - 25mm thick set over and including high performence adhisive manufactured by somani ezifix tile adhisive or equivalent mixed in cement as per manufacturer instruction and jointed with polymer modified cementetious grout manufactured by somani ezy grout or equivalnet of pigment matching to tile color including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6

M & L for preparing old plastered surfaces of walls and applying two coats of white wash.

M & L for preparing new plastered surfaces of walls and applying three coats of white wash.

M & L for 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in shutter.

M & L for MS 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete.

S&F Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed size 300 mm

S&F butt hinges medium wt 100 mm size cold rolled steel

INTERNAL ELETRIFICATION Taking down existing unserviceable copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc all as specified and directed

Modular Point wiring M & L for modular Point wiring using approved colour coding as per IS (RYBN), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, rigid PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), in modular boxes sunken in wall ( with earth dolly) with Modular switch cover (PVC) of suitable module for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site as given in Item No. 176.01 to 176.08 (NOTE: Modular Switch and socket, modular sunken boxes modular switch cover inner and outer to be measured and paid for separately:-

(a) One light point controlled by one switch 6Amps (one way)

(b) One fan point controlled by one switch 6Amps (one way)

(c) One bell point controlled by one switch 6Amps (one way)

(d) One exhaust fan point controlled by one switch 6Amps (one way)

(e) One 3 pin switch socket combination 6Amps on the independent board.

(f) One 3 pin socket outlet on same board with other switches.

(g) All as described above but point wiring with using 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed cable 1100 volt grade and 2.50 sqmm PVC insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

(h) One light point controlled by two 2 - way switches, with cables 1.5 sq. mm size

Point wiring for piano type switch and sockets M & L for Point wiring using approved colour coding as per IS (RYBN), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site as given in Item No. 177.01 to 177.03 (NOTE: Piano type Switch and sockets measured and paid for separately:-

(a) One light point controlled by one 5/6 amps one way switch

(b) One Ceiling fan point controlled by one 5/6 amps one way switch and one fan regulator

(c) One Socket outlet, three/five pin, 5 Amp, controlled by by one 5/6 amps one way switch or switch/socket combination 5 amps, 5 pin with other switches on same board

M&L MODULAR switch 1 way 6Amps, 1 module

Supply and fixing Modular type switch 2 way 6A, 1module, 230 V,AC 50Hz ISI Marked with valid CML No. complete

Supply and fixing Modular type socket outlet multipurpose having provision for 3 pin 6A and 2 pin 6A, 2 module, 230 V,AC 50Hz ISI Marked with valid CML No. complete all as per

M&L Modular switch 1 way 16A, 1 module

M&L Socket 6A/16A - 2/3 pin combined , 2 module

S&F Modular electronic type fan step regulator, 120W - 2 module

S&F Modular white or Ivory cover plate with frame, 1 module

S&F Modular white or Ivory cover plate with frame, 2 module

S&F Modular white or Ivory cover plate with frame, 3 module

S&F Modular white or Ivory cover plate with frame, 4 module

S&F Modular white or Ivory cover plate with frame, 6 module

S&F Modular white or Ivory cover plate with frame, 8 module

S&F Modular white or Ivory cover plate with frame, 12 module

Supply and fixing of modular blank Dummy models module

M&L for Metal flush box 1/2 module

M&L for Metal flush box 3 module

M&L for Metal flush box 4 module

M&L for Metal flush box 6 module

M&L for Metal flush box 8 module

M&L for Metal flush box 12 module

S&F ceiling rose 65x17mm three terminals 3 phase/PVC/polycarbonate, isolated body

Supply and fixing Switch piano; flush type, single pole 230V AC 50Hz one way, 5/6 Amp IS:3854 marked with valid CML No. complete all as specified.

M&L switch socket combination 2 in 1, 5 pin 6 amps flush type.

S & F stepped type electronic fan regulator flush type

S& F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting.

Supply and fixing Modular Bell push 6A 1 module, 230V

Supply and fixing of bell 230V Ac single phase module

S&F Sheet Metal Enclosure with socket plug top and MCBs double pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 240V, 20 Amps

S&F decorative mirror type LED tube light fitting 1x9/10 watt including LED tubular lamp with IP20 protection, inbuilt driver etc complete with all accessoris internally pre-wired including connecting up with twin core twisted flexible copper conductor cable of 1.0 Sqmm size complete all as specified and directed

S&F decorative box type LED tube light fitting 1x20/18 watt including LED tubular lamp with IP20 protection, inbuilt driver etc complete with all accessories internally pre-wired incluidng connecting up with twin core twisted flexible copper conductor cable of 1.0 Sqmm size complete all as specified and directed

S&F LED Security light fitting made out of pressure die cast aluminium powder coated housing high impact resistant 4mm thick toughened glass cover and matrix of power LEDs inbuilt electronic driver upto 10 KV surge protection fitted with adjustable pole adapter to enable on site tilt angle setting depending on road geometry CCT3000-6000 CRI greater than 70, input power 30 W system with 100 lumens per watt output operating voltage 160--260V with connection by three core PVC insulated multistaranded copper conductor sheathed cable of size 1.0 Sqmm fixed with & copper conductor sheathed cable of size 1.0 Sqmm fixed with complete all as specified and directed. Note :- (a) The LED lights shall have guarantee for 5 years from date of completion of contract, any defects noticed during this period shall have be rectified/ Parts replaced immediately, security amount of 10% of the cost of the item shall be retained with the Deptt till end of the guarantee period. (b) LED light manufacturer lab shall be accredited to NABL.

M&L for replacement of 25 mm bore light grade GI pipe fixed as bracket, on poles/buildings any type, not less than 1.0 m long and bent to shape as required complete with suitable clamp made out of 25x4mm Flat Iron duly fixed 12mm dia nuts, bolts, washers etc.suitable for steel tubular / PCC pole complete all as specified and directed by Engineer-in-Charge.

M&L earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part I and testing on completion including necessary excavation and earth work in any type of soil,PCC(1:3:6)type C1 chamber, with cast iron frame,funnel with watering pipe 20mm dia medium grade,wire mesh and lugs,GI protection pipw,15mm dia,medium grade,7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

Supply and fixing ceiling fan 1200 mm sweep 5 star rating including fixing of down rod and connection complete with & including of flexible three core PVC insulated multi-stranded copper conductor cable of size 0.50 sq mm from ceiling rose/connector to fan complete all as specified and directed. Model - Asset 50 of Make : Crompton Greaves or equivalent in Bajaj/Havells

Supply, fixing, testing & commissioning of exhaust fan 300 mm sweep 5 star rating with minimum airflow/air delivery 1710 cmh, totally enclosed heavy duty motor, die cast aluminium rotor mounted on double ball bearing, IP-55, polarity-4, 230 Volt AC supply (single phase), rated power sheathed copper conductor cable from ceiling rose to fan. Make : CG/Bajaj/Havells or equivalent. similar to Cormpton Greaves model No Transair 12" - Reversible,

Taking down existing UNSV Water heater including all accessories and to be deposited in AGE E/M store yard

S & F 25 litre storage water heater, rated power consumption not more than 1500w, current leakage protection device, multi functional safety valve, high precision thermostat control, preset thermal output, high working pressure 0.8Mpa ideal for high rise building, vertical mounting, Operating voltage 230 volts including all fittings complete & provision of flexible three core PVC insulated multi - stranded copper conductor cable, Make : HAVELLS cat part No GHWASESWH025 or equivalent make mentioned in Appx 'B'. Note : Old ceiling fans, exhaust fans, water heaters retrieved against respective items of BOQ shall be deposited to AGE E/M Store Yard of Baroda

EXTERNAL ELECTRIFICATION M&L for sand cushoning, to UG cable with using river sand locally available and punning to provide required cover for UG cables all as directed by the the Engineer in Charge.

M&L brick protection cover to electric cable with class 'B' bricks laid dry and flat abutting each other with gap between adjacent not exceeding 10mm.

Supply and laying or fixing or passing through pipe,XLPE insulated PVC sheathed armoured heavy duty electric cable with aluminium conducto1100 volts grade cross sectional area 50 sqmm 3.5 Core .

M&L for galvanized steel tubing light Grade of 40 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

Taking down carefully Old LT Cable of any size all as specified and directed by Engineer in Charge and removing from site of work

EXTERNAL WATER SUPPLY Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 50 mm bore of pipe complete all as specified.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 25 mm bore of pipe complete all as specified.

S&F 50 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 50 mm dia

M&L brick masonary valve pit chamber of size 750mm X 750mm X 750mm (internal dimension) complete with MS angle iron frame work (Angle Iron size 40mm X 40mm X 6mm) & 3mm MS sheet top cover openable through hinges including necessary locking arrangement, rendering complete and painting with two coat of black bituminous paint over a one coat red oxide primer

Taking down Old GI Steel tubing of 50/25 mm dia complete all as specified and directed

Taking down Old Gun metal gate valve of 50/25 mm dia complete all as specified and directed