Special Repair of Upgradation of SHC into HWC At Village Tandwal in Ambala District

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. (HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement. (HSR 8.5(b))

Dismantling roofing first class mud roofing. (HSR 8.8(a))

Removing door and windows (wood and steel) with chowkats by making Recesses in walls when the wall is not to be dismantled. (HSR 8.18) (a) Door

(b) Windows

(c) Ventilators

Scraping. (HSR 8.32) (a) Cement Plaster

(c) White wash and colour wash

Dismantling cement eonglomerate/terrazzo floor 25mm to 50mm thick without concrete base. (HSR 8.26)

Cement concrete 1:4:8 with stone aggregate 40mm Nominal size in foundation and plinth. (HSR 10.39)

Cement concrete 1:11/2:3 with stone aggregate 20mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respects. (HSR 10.81+10.95(a))

Providing and laying 80mm thick Interlocking Paver Blocks (ISI Mark) as per IS 15658:2006/ IRC: SP:63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9)

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.14)

Cement concrete 1:2:4 gola 10 cm X 10 cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Providing fixing PVC rain water pipe 6 Kg. Pressure of “Poly India” brand ISI marked in cement mortar during masonry work. (HSR 13.89(a)) (a) 100mm dia PVC pipe 6 Kg. Pressure

Providing & fixing PVC Bend ISI Mark. (HSR 13.90(a)) (a) 100mm dia PVC Bend

Providing and fixing vitrified tiles of size 600mmx600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of raputed manufecturer like NITCO, AJARIA,SOMANY,ORIENT,JOHNSON & RAK. (HSR 14.89)

Providing and fixing vitrified tiles of size 600mmx600mm of approved make in skirting /dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of raputed manufecturer like NITCO, KAJARIA,SOMANY,ORIENT,JOHNSON & RAK. (HSR 14.90)

Providing and fixing ceramic/anti skid tiles of size 400 mmx400mm,or above size of approved make in floors, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of raputed manufecturer like NITCO, KAJARIA,SOMANY,ORIENT,JOHNSON & RAK. (HSR 14.91)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to I.S.15662 (thickness to be specified by the manufecturer) of approved make in all colors, shades except burgundy ,bottle green, black of any size as approved by Engineer-in- Charge in skirting,risers of steps and dados over 12mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92(a)) (a) Size of ceramic Glazed tiles 200mm x 300mm

12mm thick cement plaster 1:6. (HSR 15.7)

15mm thick cement plaster 1:6 on the rough side of single of half brick wall. (HSR 15.12)

Cement pointing 1:2 deep variety on brick and Tile work. (HSR 15.60)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler,consisting of white lead, linseed oil, varnish and chalk mittii including finishing Preparation of plastered surfaces for oil bound distemper including sand papering. (HSR 16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats on new work. (HSR 16.58)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79(b)) 1st Quality

Cost of aluminium fitting compelte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt). (HSR 17.72(b)) for double lead shutter

Providing and fixing sliding bolt with nuts and screws etc. complete. (HSR 17.83(b)(i)) Size 300mm x 16mm

Factory- manufactured paneled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than tak, conforming ot I.S. specification no. 1003, kiln-seassoned), with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail and 100 mmm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in positon (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in positon) (HSR 17.90) - Note under 17.18)) 35mm thick

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., (non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical syltes, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W. R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in positon. (HSR 17.91(b)) - Note under 17.18)) 35mm thick

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position). (HSR 17.92(ii)) - Note under 17.18)) 35mm thick

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. Note :- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for inforcement. (HSR 18.22)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete. (HSR 18.34) (a) door and window frame of size 89mm X 50mm with 40mm wide single rebate

(d) door and window frame of size 114mm X 50mm with 40mm wide double rebate.

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary Fittings as fully described in item no. 30.3 above. (HSR 30.4(i)) White

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in- Charge) BIDET, SUITE consisting of BIDET SUITE IN VITREOUS CHINAWARE 380 MM HIGH (as approved by the Engineer-In-charge) BEST CHROMIUM PLATED BRASS BIDET FITTINGS FOUR HOLES-BASIN MIXER WITH POP-WASTE ETC., COMPLETE (as Approved by the Engineer-in-charge). COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS AND PAINTINGS OF FITTINGS ETC. (HSR 30.7(i)) White

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. (HSR 30.13(i)) White plastic seat (Solid)

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I BRACKETS for building into wall including Painting; 32 mm C.P BRASS WASTER WITH C.P brass chain and rubber plug; 15 mm C.P BRASS SCREW DOWN PILLAR TAP WITH Jamnuts or couplings best design ( as approved by the Engineer- In-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41(iv)) Size 550mm x 400mm with one no. tap

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE PAPER HOLDERS FIXED INTO wall with C.P Brass screws complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.67(a)) C.P. Brass

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.68) (d)) C.P brass two swivel towel rail 400 mm long

(e)) C.P brass towel ring

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etcs. (HSR 30.70(a)(i)) Soap dish 160mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71(a)(i)) 600mm x 450mm

Providing and fixing in position super quality 65mm i/d opening C.P brass dome type hinged grating weighing about 750 gms fixed in cement mortar 1:2 complete in all respects (as required by the Engineer-in-charge). (HSR 30.74)

Providing and fixing in position 15mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge). (HSR 30.75) (a) Bib cock long body

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge). (HSR 30.76(a)(ii)) Concealed stop cock with flange

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION. (HSR 30.82(b)(iii)) 15mm x 450mm

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASSBALL VALVES IN TANKS. (HSR 30.110(b)(ii)) 20mm internal diameter

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work). (HSR 30.119) 500 Ltr. Capacity

Providing and fixing Poly Carbonate Sheet roofing 6mm thick including frame (iron) complete in all respect. (N.S.)

Note :- In case of any difference in the unit & nomenclature of any of the HSR items of Civil items depicted in the DNIT and that given in HSR the unit and nomenclature given in HSR shall be applicable.

JAGDEEP SINGH

Gurmeet Singh