Tender for ARC work of aying, testing and commissioning of 11/22 KV XLPE Cable (XLPE Cable to be Supplied by DGVCL) with Cable End Termination & straight through joint kits (to be supplied by contractor) amounting Rs 80,00,000 undervarious scheme under jurisdiction of Kadodara Ind s/dn of Kadodara Division.

CAPITAL WORK LABOUR RATES FOR FY 2025-26 (WITHOUT GST)

Sr. Item Code Item Unit Rate

Labour charge for excavation of cable trench of 400mm

width x 1200mm depth, in any type of soil for laying of

1 9925000001 cable of size up to 240 mm2 (For additional cable 200 Meter

mm additional width shall be considered i.e. half trench

length is to be considered)

Labour charge for excavation of cable trench of 600mm

width x 1200mm depth, in any type of soil for laying of

2 9925000002 cable of size up to 240 mm2 (For additional cable 200 Meter

mm additional width shall be considered i.e. half trench

length is to be considered)

Labour charge for excavation of cable trench of 400mm

width x 1500mm depth, in any type of soil for laying of

3 9925000003 cable of size up to 240 mm2 (For additional cable 200 Meter

mm additional width shall be considered i.e. half trench

length is to be considered)

Labour charge for laying of 11kV / 22 kV XLPE Cable of

size up to 240 mm2 & preparation of sand layer 100mm

thick, in the cable trench & covering the cable with

mm dia (Inner), thickness 25 mm, 1.0 meter long RCC

half round muffs and providing and fixing of 4inch width

4 9925000004 yellow colour polyethylene tape with printing "CAUTION Meter

ELECTRIC CABLE BELOW" at 0.75 m depth from ground

surface after laying cable in trench. This will provide

indication that electric cable is passing underground so

as to protect cable from mechnical injuries, refilling the

same, as per Instruction of Engineer in Charge (EIC).

Labour charge for horizontal drilling using Auger

machine without damage to surface road at max

mtrs depth & putting of 6.11 kg/cm2 , class-4,Green

color, 110mm O.D. , 8.5mm thickness H.D.P.E. pipe

confirms to IS 4984- 1987(3rd revision) and BIS

certification and laying of 11KV/22KV XLPE cable of size

up to 240 mm2 in HDPE pipe, as per Site Condition

(excluding cost of pipe). The detail map obtained from

HDD machine and excell sheet(hard and soft copy)

indicating the respective depth and distance from

adjacent landmark for each segment for HDD is must

required to be submitted. HDD to be carried out at depth

1.5 mtrs to 2.0 mtrs as per site conditions and as per

instruction of EIC.

Labour charge for horizontal drilling manually without

damage to surface road at max 2.0 mtrs depth & putting

of 6.11 kg/cm2 , class-4,Green color, 110mm

O.D. , 8.5mm thickness H.D.P.E. pipe confirms to IS 4984-

1987(3rd revision) and BIS certification and laying of

11KV/22KV XLPE cable of size up to 240 mm2 size, as

per Site Condition (excluding cost of pipe). The detail

map and excell sheet(hard and soft copy) indicating the

respective depth and distance from adjacent landmark

for each segment of cable to be submitted. Drilling to be

carried out at depth Minimum 1.2 mtrs to 2.0 mtrs as per

site conditions as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D.

8.5 mm thickness

7 9925000007 H.D.P.E. pipe confirms to IS 4984 and BIS certification Meter

for laying of underground 11KV / 22KV XLPE cable up to

Labour work for RCC concreting on disputed location

and repairing of damage portion of road crossing for the

work carried out for roads crossing as well as concreting

& muffing of ploes including all materials (1:2:4)

Providing & fixing concrete stone route marker of

mm width x 150 mm thick x 650 mm height embedded in

earth at least 300 mm below & 350 mm above ground

level respectively at distance approx 50 meters along

the length of cable. The RCC concreting (1:2:4)(all

necessary maeterials will be in bidder's scope) of route

marker is to be carried out 300 mm width x 150 mm

9 9925000009 thick x 300 mm below ground level as per instruction No.

of EIC. The route marker should be with name of

company with approved yellow colour-DGVCL. The

distance from marker to cable and cable depth with

feeder name etc., marked with arrow sign is to be

painted on it.The route marker is to be fixed at location

near to any fixed permanent location (not necessary to

fix exact on top of cable) as per instruction of EIC.

Erection of D.P. (double pole) structure using 9 / 11 Mtr.

RSJ pole with cable connection arrangement along with

10 9925000010 fitting of necessary fabrication for 11KV cable including No.

excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 9 / 11 Mtr RSJ

pole with cable connection arrangement along with

fitting ofnecessary fabrication for 11KV/22 KV cable

including excavation of pit & refilling of earth as per

instruction of EIC. (Exclusive of concreting & muffing of

Erection of D.P. (double pole) structure using 8.0 Mtr.

PSC pole with cable connection arrangement along with

12 9925000012 fitting of necessary fabrication for 11KV cable including No.

excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 8.0 Mtr PSC pole

with cable connection arrangement along with fitting

13 9925000013 ofnecessary fabrication for 11KV/22 KV cable including No.

excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles)

Labour charge for erecting of 11kV / 22 kV XLPE cable of

size up to 240 mm2 on DP Structure with fixing of 02 Nos

14 9925000014 polymer cleats on top and middle part.Polymer cleats,

nut bolts etc. fixing material to be provided by

Providing & fixing of 6.11kg/cm2 , class-4,Green color,

110mm O.D. , 8.5mm thickness H.D.P.E. pipe confirms to

IS 4984 and BIS certification on the erected DP structure

for the mechanical protection of cable by inserting the

cable inside HDPE pipe. The HDPE pipe shall be erected Per

in such a way that 300mm shall be below the ground Job

level and the rest 2700 mm shall be supported on the

DP Structure with 01 No Polymer cleat.All materials

including polymer cleat and Nut bolt to be provided by

Providing and fixing of pipe type earthing from 80 mm dia

class-B GI pipe with pit to be filled with salt & coke and

construction of chamber as per DGVCL Drg. No. dg /100

16 9925000016 for DP and cable. The earthing pit should be joined with No.

cable by G.I. strip of size 1” width & 2 mm thick. All

material GI pipe, Coke, Salt etc will be supplied by

Supply & fixing of heat shrink type end terminations

17 9925000017 (outdoor) for upto 11kV 3C x 185 mm2 size XLPE cable as No.

per DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations

(outdoor) for upto 22 kV

3C x 185 mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat shrink type end terminations

19 9925000019 (indoor) for upto 11kV 3C x 185 mm2 size XLPE cable as No.

per DGVCL technical specification)

Supply & fixing of heat & shrinkable end terminations

(indoor) for upto 22 kV

3C x 185 mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat shrinkable straight through joint

for upto 11kV 3C x

185 mm2 size XLPE cableas per DGVCL technical

Supply & fixing of heat shrinkable straight through joint

22 9925000022 type for upto 22kV 3C x 185 mm2 size XLPE cable as per No.

DGVCL technical specification

Labour charge for excavation of 2100mm long x

1200mm wide x 1200 mm deep joint pits for installation

of 11kV / 22kV Straight through joints as per instruction

of engineer-in-charge & covering the cable with 150 mm

dia (Outer), thickness 25 mm, 1.0 meter long RCC half

round muffs & refilling same as per instruction of EIC .

Providing and fixing of insulating bus bar, made from

11KV/22KV XLPE cable after removal of semi conducting

layer and applying of PVC heat shrinkable anti- tracking

core insulating tubing (1.1KV), on both end terminal

using Aluminium long barrel heavy duty up to 240 sq mm

24 9925000024 lugs, Aluminium bus connector. Taping with PG- clamp No.

for bus conductor as per drawing and as per instruction

of EIC. The Alluminium lugs and PG clamp shall be

covered with 11KV/22KV HT insulating

tapes.(11KV/22KV XLPE cable will be in scope of DGVCL

while all other materials will be in bidder's scope)

Testing of cable at various points and commissioning the

25 9925000025 feeder as per instruction of engineer-in-charge.Test No.

result shall be submitted by contractor with bill.

Preparation and submission of 6 (six) copies, of

complete layout drawings with GIS mapping as per

actual cable routing showing road crossing, HDPE pipe

sleeving, jointing locations, markers etc.

Providing and fixing of Sign Board at junction point Made

out of 2 mm aluminium sheet size 750x300 mm (2.5 x

ft) rectangle, as per design, pretreated with phosphate

process and acid etching coated with one coat of epoxy

primer and two coats of best quality paints, reflectorized

with Hi Intensity retro — reflective sheeting as per the

latest and frame fabricated from suitable size iron angle.

The Sign Board is to be fixed on the base prepared from

channel and bracing angles which is grouted by means

of cement concreting of 1:2:4 for size of 300 mm dia x

800 mm height (500 mm to be grouted in ground). The

details to be displayed on sign board will be given by

InchargeEngineer. (a) Hi intensity Micro prismatic

Providing and fixing of Sign Board (Danger Board) on

Distribution Transformer Centers Made out of 2mm

aluminium sheet size 300x300mm (1X1 ft) as per design,

pre treated with phosphate process and acid etching

coated with one coat of epoxy primer and two coats of

28 9925000028 best quality paints, reflectorized with Hi-Intensity No

retroreflective sheeting as per the latest and frame

fabricated from suitable size iron angle. The Sign Board

(Danger Board is to be fixed at the location as per

instruction of In-charge Engineer. (a) Hi intensity Micro

prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x

75 mm (W) from 3 mm aluminium sheet along with

mm dia aluminium binding wire for fixing of aluminium

tag near end termination joint at DP structure for

identifyng the cable. The details of feeder i.e. 11 / 22 KV

with feeder name shound be punched on the tag by letter

punch of size 16 mm as per instruction of In-charge

Supply & fixing of heat shrink type end terminations

30 9925000030 (outdoor) for 11kV 3C x 240 mm2 size XLPE cable as per No.

DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations

31 9925000031 (outdoor) for 22 kV 3C x 240 mm2 size XLPE cable as No.

per DGVCL technical specification)

Supply & fixing of heat shrink type end terminations

32 9925000032 (indoor) for 11kV 3C x 240 mm2 size XLPE cable as per No.

DGVCL technical specification)

Supply & fixing of heat & shrinkable end terminations

33 9925000033 (indoor) for 22 kV 3C x 240 mm2 size XLPE cable as per No.

DGVCL technical specification

Supply & fixing of heat shrinkable straight through joint

34 9925000034 for 11kV 3C x 240 mm2 size XLPE cableas per DGVCL No.

technical specification.

Supply & fixing of heat shrinkable straight through joint

35 9925000035 type for 22kV 3C x 240 mm2 size XLPE cable as per No.

DGVCL technical specification

Installation, Testing and commissioning of 11 KV,630 A

SCADA Compatible, RRL type3 Way RMU including Two

36 9925000038 numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical

Installation, Testing and commissioning of 11 KV,630 A

SCADA Compatible, RRLL type4 Way RMU including Two

37 9925000039 numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical

Installation, Testing and commissioning of 22KV,630 A

SCADA Compatible, RRL type-3 Way, RMU including Two

38 9925000040 numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical

Installation, Testing and commissioning of 22KV,630 A

SCADA Compatible, RRLL type-4 Way, RMU including

39 9925000041 Two numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical

Construction of plinth for 11KV, RRL type- 3 Way( i.e Two

numbers of Isolator & One number of Breaker) Ring Main

40 9925000042 Unit as per DGVCL's technical specification mentioned Nos

in drawing no: Drg. 11kv-01. All required material will be

supplied by contractor.

Construction of plinth for 11KV, RRLL type4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main

41 9925000043 Unit as per DGVCL's technical specification mentioned Nos

in drawing no:Drg. 11kv-02.AlI required material will be

supplied by contractor.

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two

numbers of Isolator & One number of Breaker) Ring Main

42 9925000044 Unit as per DGVCL's technical specification mentioned Nos

in drawing no: Drg. 22kv-01. All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRLL type4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main

43 9925000045 Unit as per DGVCL's technical specification mentioned Nos

in drawing no:Drg. 22kv-02.All required material will be

supplied by contractor.

Modifications e.g. Providing and fixing ofTerminal

protectors i.e. Re-use able boot (HT Side 11/22KV, LT

Side 1.1KV) including 11/22 KV insulating taps and

L.T.(I.I KV) insulating taps ,Busbar, Tapping from Bus Bar

(11/22 KV XLPE cable) through P.G. Clamp for H.T.

Jumper to D.O. Fuse to bushings of Transformer Center,

providing & Fixing of jumper and providing & fixing of

Heat Shrinkable Anti Tracking CoreInsulating Tubing

44 9925000046 (Insulation Level 11/22 KV) in H.T. jumper , Clamping Nos.

arrangement of cable support frame on both side of

existing Over Head type Distribution Transformer to

utilize in Under Ground cable network as per drawing &

as per instruction of Engineer incharge. All live parts i.e.

PGClamp, connections of D.O.fuses, HT bushings etc .

shall be covered with fixing of 11/22 KV HT insulating

tapes. ( 11/22 KV XLPE cable will be in scope of DGVCL

while all other materials will be in bidder's scope )

Laying of any size of 11/ 22 KV XLPE /PILC Cable in Cable

redaymade trench or in open space Per

46 9925000060 Labour charges for Lying of O/H XLPE cable pole to pole KM

Supply of 150 mm dia (Inner), thickness 25 mm,

meter long RCC half round pipe

Total Estimated Amount (Exl. Gst )

Eighty lac only

Executive Engineer (O&M),

D.G.V.C.L., Kadodara Division