Establishment of Critical Care Block (CCB) and Communicable Disease Centre (CDC) at AGMC and GBP Hospital Complex, Agartala, Tripura West / Building portion including retaining wall internal water supply, Sanitary installation, Sewage and Drainage wo

Amount

SUB-HEAD : EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. - All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. - All kinds of soil

Extra for additional lift of 1.5m or part thereof. - All kinds of soil

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Providing Pre-constructional anti- termite treatment conforming to IS- 6313 (part II) using chloropyrifos EC 20 Emulsion or equivalent of 1% concentration by weight for creating barrier under and all around foundation pits, wall trenches, basement excavation, backfill in immediate contact with foundation and treating the top surface of plinth filling, junction of wall & floor, along the external perimeter of building, expansion joints, surrounding of pipes, water conduits and at places suggested and as directed by Engineer-In Charge covering 10 years guarantee. [Plinth area of LG-2 will be considered for payment]

SUB-HEAD : CEMENT CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - - All work upto plinth level:

1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size)

1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size)

Centering shuttering including struttings, propping etc. and removal of form work for:

Foundations, footings, bases for columns.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

SUB-HEAD : REINFORCED CEMENT CONCRETE WORK

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- - All work upto plinth level:

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases excluding the cost of centring, shuttering, finishing and reinforcement-

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) / Upto Floor Five Level

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) / Above floor V level for each Four Floors or part thereof

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with

1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Centering shuttering including struttings, propping etc. and removal of form work for:

Foundations, footings, bases for columns etc. for mass concrete with steel formwork

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply

Suspended floors, roofs, landings, balconies and access platform with M.S. plates and props

Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply

Columns, Pillars, Piers, Abutments, Posts and Struts with M.S. shutters

Stairs (excluding landings) except spiral-staircases with wooden plank

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.

Weather shade, Chajjas, corbels etc., including edges.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size).

Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits

50 mm thick

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.

All works upto plinth level - Reinforced cement concrete grade M-30 B.M.C/R.M.C

All works upto Floor five level - Reinforced cement concrete grade M-30 B.M.C/R.M.C

R.C.C./B.M.C./R.M.C. work above floor five level for each four floors or part thereof - Reinforced cement concrete grade M-30 B.M.C/R.M.C

Providing and fixing Bird wired mesh / Wired febric (24 Swg, 12.5 mm size) in strips of 250 mm width or as required properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members complete as directed by Engineer-in-Charge.

SUB-HEAD : PILE WORK

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct Mud Circulation (DMC) or Bailer and Chisel Technique by Tripod and Mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads. (Length of pile for payment shall be measured upto bottom of pile cap). Note: Truck Mounted rotary / TMR / Tubewell Boring Machine shall not be used.

600 mm dia piles.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in­charge:- Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic Method of Testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-Charge. Single pile above 50 tonne and upto 100 tonne safe capacity pile:-

Initial test (Test Load 2.5 times the safe Capacity).

Routine test (Test Load 1.5 times the safe Capacity).

SUB-HEAD : BRICK WORK

First class brick work in foundation and plinth including cost of all materials as required complete :-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete :-

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

First class brick work in superstructure above floor-V level for each four floors or part thereof by mechanical means by lifting material using mobile crane as required complete.:-

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Half brick masonry work in superstructure above floor-V level for each four floors or part thereof by mechanical means by lifting material using mobile crane as required complete.:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Extra for providing & placing in position 2 nos 6mm dia MS bars at every 6th course of full brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:-

In cement mortar 1:6 ( 1 cement : 6 fine sand ).

Extra for providing & placing in position 2 nos 6mm dia MS bars at every 4th course of half brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:-

In cement mortar 1:4 ( 1 cement : 4 fine sand ).

SUB-HEAD : WOOD & PVC WORK

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/ Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 125 mm

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass (weight not less than 10ks/Sqm) panes including black enamelled ISI marked MS butt hinges with necessary screws.

Local Teak wood - 35 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors including cost of 5.5mm thick glass (overall area of door shutter to be measured) :

Rectangular or square

Providing 50 × 50 × 50 mm Gamair wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 fine sand) and making good the walls etc.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets including fixing with 25 × 3 mm M.S. flat 10 cm long and rawl plugs 50 mm long (designation 10 no.) etc. all complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality)

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Single rubber stopper

Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws.

Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter).

Lead Lined doors - Painted a) Providing and fixing of hollow metal door at all levels from ISO 9001- 2015 certified manufacturer. All hollow metal general doors with or without vision panel. Pressed galvanised steel Single /Double leaf to required sizes of approved make Shakti Hormann or approved equivalent which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. b) Door frame shall be double rebate profile of size 143 x 57mm made out of 1.6mm (14gauge) thick galvanized steel sheet. Frames shall be butted and field assembled with bolts. The inside face of the frame face trim to rebate height should be protected with 1.6mm thick lead line. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the strike jamb. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for doors on the clear masonry opening.

c) Door leaf shall be 48mm thick fully flush double skin door. Door leaf shall be manufactured from 1.2mm (18guage) thick galvanised steel sheet. The internal construction of the door should be rigid with lead line of 1.6mm thick all across the inside of the exposed surface. In addition the door should have steel channel reinforcement with a basic infill of honeycomb core. All doors should be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers as per ANSI Standard. The edges should be interlocked with lock seam. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Hardware shall be of approved make. d) Vision panel of size 200 x 300mm to be provided. Lead line glass of 8.5mm with radiation shield shall be provided with beeding arrangement. e) All doors and frames shall be finished Pure Polyster Powder coated and shall have passed minimum 500 hours of salt sprey test. f) Rate should include supply and installation of door and hardware as a complete assembly as mentioned in the door and hardware schedule. The hollow section of the frame shall be filled with puff Lead line Door Double leaf of size : 1800 x 2250 with hardware complete

SS Door for CSSD Providing and fixing of hollow metal door at all levels from ISO 9001- 2000 certified manufacturer. All hollow metal general doors with or without vision panel. Pressed Stainless steel Single /Double leaf to required sizes of approved make Shakti Hormann or approved equivalent which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. Door frame shall be Single rebate profile of size 125 x 60mm made out of 1.60mm thick Stainless steel sheet (14 gauge). Frames should be mitered and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be filled with PUF as recommended by the manufacturer.

Door leaf should be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 1.2mm (18 guage) thick Stainless steel sheet. The internal construction of the door should be rigid with steel stiffeners/ pads and reinforcement. The infill material shall be resin bonded honeycomb core. All doors should be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be Double side as per joinery details with a screw on glass beeding on the inside. The glass should be 5mm clear toughened glass. All doors and frames shall be finished satin Stainless Steel. Rate should include supply and installation of door and hardware as a complete assembly as mentioned in the door and hardware schedule. The hollow section of the frame shall be filled with puff Multipurpose Door Single leaf of Door size: 1250 x 2250mm with vision panel 200 x 300mm with hardware complete

Providing and fixing Automatic Sliding Hermetic (airtight) OT door having 1500 mm x 2100 mm size of stainless steel door leaf with stainless steel frame with inner core Polyurethane foam or honeycomb structure for sound proof and insulation with anti-bacterial and anti-static finishes, having rubber gaskets along the frame to ensure an airtight seal with special track design for hermetic sealing when fully closed, fully automatic via a motorized sliding mechanism, with options for manual operation in case of emergency, infrared sensors, foot sensor with obstacle detection and anti-pinch mechanism, having Touchscreen control interface outside and inside the OT, Integration with access control (keypad or biometric) for restricted areas, Automatic interlocking for OT with sterile conditions, Hermetic sealing up to ISO Class 5 (Cleanroom standards), Low operating noise, typically below 50 dB, fire-rated version, Integrated glass window with lead lining for X-ray protection, Lead-lining available for radiation-protected environments, Automatic emergency release with power supply 220V AC, 50/60Hz, compliance with CE certified, ISO 14644, and other OT standards.

SUB-HEAD : STEEL WORK

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:-

80x 1.25mm M.S. laths with 1.25 mm thick top cover.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-

In stringers, treads, landing etc. of stair cases including use of chequered plate wherever required, all complete.

Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:-

M.S. tube

Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing, fabricating, transporting, assembling and erection in position of Steel members for steel colunms, built up beams using structural tubular sections (confirming to IS 2062 -1999 grade B Fe 410, normalized control cooled , yield strength + 250 MPa as per latest IS Code) to the required profile & shape as called for as per the drawing & specifications and of approved make including the shear connectors /studs and fusion weld to top of horizontal member. This item also includes prepration of shop drawings and their approval, necessary templates, adequate temporary supports, scaffolding & staging, all cutting, grinding, sliding & all labour tools, plants & equipments & operations etc. required to complete the job as per drawing & specification. Every precaution to be taken to prevent rusting of sections. This item also includes all test on materials & welded fabricated parts as per specification and direction of Engineer - in - Charge. Temporary bolts & nuts ( grade EN 8 ) to be used during assembling & shall be removed before site erection. All site erection bolts shall be HSFG type only. The item to include cost of sand blasting on materials, application of primer and epoxy paint in internal & external in fabrication shop & final painting on site including all touch up works after erection as per technical specification.

SUB-HEAD : ALUMINIUM WORK & STRUCTURAL GLAZING

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer­in­charge. (Glazing and paneling and dash fasteners to be paid for separately) :-

For fixed portion of approved quality:- - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-

With float glass panes of 5.5 mm thickness ( weight not less than 13.50 kg / sqm )

With Toughened glass panes of 12 mm thickness

Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealant over backer rod of approved quality etc. complete as per architectural drawing and direction of the Engineer-in charge.

Upto 5 mm depth and 5 mm width.

Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:-

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-

Anodised aluminium of grade AC 15.

Providing and fixing SS Mosquito mesh in anodised (anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodising must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) aluminium shutter fixed in sliding/openable/fixed windows conforming to IS: 1948-1961 as per drawing and directed by Engineer-in-charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing 6mm thick Suede Finish Greenlam Clads, Rehau, Exidec, Trespa, Fundermax Exterior Grade High Pressure Compact Laminates having 1300mm x 3050mm board size made out of urea free, thermosetting phenolic resins treated Kraft papers as core material and Amino plastic resin treated decor papers along with UV protection film on both side finish surfaces. Clads should conform to European Fire Rating norms of Bs1d0 when classified in accordance with EN 13501-1: 2007, the Fire Retardant Additive must be Halogen free in order to protect environment. It should have Antibacterial and Antifungal properties (conforming to JIS Z2801:2010 and ASTM G21-2015 standards respectively). Clads should have density >1350 kg/m3, Anti-graffiti properties and Resistant to climatic shock, UV light, Grey Scale contrast (1500 hours of exposure-rating-4), Artificial weathering (including light fastness) with a Grey Scale Rating not worse than 4 after exposure to 650 MJ/m2, Acid Rain, Corrosion (on a salt spray test for 700 hours) as per applicable specifications conforming to latest and applicable EN 438-6: 2016 EDF Grade quality standards. It should be CE certified for constancy of performance described

by in Annexure ZA of the standard EN 438-7:2005 under systern-1. The product to be warrantied against manufacturing defects and performance characteristics (as per manufacturer product warranty) for a period of 12 years from the date of billing from factory. Clads should be installed on Aluminum tubular substructure in the size of 50mm x 25mm x 1.8mm or as per site requirement laid vertically at 450 mm c/c distance with the help of 5mm diameter colour matching rivets as per manufacturer specifications. The aluminum tubular substructure should be fixed on wall with the help of dead load bearing brackets and wind load bracket by 10mm fastener. Wind load bracket will have vertical slot & dead load bracket will have in horizontal slot. Maintain 6mm both horizontal and vertical gap between two installed clads panels. Shade/design of clads should be finalized under direction of Engineer-in-charge.

SUB-HEAD : FLOORING AND SKIRTING WORK

Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips [40mm wide and 4 mm thick] etc. all complete as per direction of Engineer-in-charge.

40 mm thick with 20 mm stone aggregate

Extra for making chequers of approved pattern in Cement Concrete floors, steps, landing, pavements etc. complete.

Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.

600 mm X 300 mm in all shades and design

Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.

Anti-skid Tiles - 300 mm x 300 mm in all shades and designs

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.

Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) - Size of tile 1200 mm x 600 mm x 10 mm (min.) thick

Providing and laying 1st class quality vitrified tiles at skirting in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. all complete as per direction of the Engineer-in-charge

Glazed Vitrified Tiles - Full Body (Glossy) - Size of tile 1200 mm x 150 mm x 10 mm (min.) thick

Providing and laying 1st class quality vitrified tiles at dado in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. all complete as per direction of the Engineer-in-charge

Glazed Vitrified Tiles - Full Body (Glossy) - Size of tile 600 mm x 600 mm x 10 mm (min.) thick

Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge.

In dark shade using ordinary cement

Providing and laying Mirror Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab.

Providing and laying Mirror Polished Granite stone flooring in treads of steps & risers and skirting in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab (using single length upto 2.00m).

Providing edge moulding to approved thickness granite stone counters, vanities, treads of steps etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge. i) 14 mm thick Granite work

Providing and fixing machine cut, mirror/ eggshell polished , Granite stone cladding in lift lobby/dado/passage, in required design and pattern wherever required of size 600 x 1200 mm, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 fine sand) laid with stainless steel fasteners cleats etc. and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

14(+2) mm thick stone slab

Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

14 mm thick Granite of any colour and shade duly approved:- - Area of slab over 0.50 sqm.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and approved thickness fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):-

Granite of any colour and shade duly approved of 14 mm thick (75 x 50 cm).

Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. [The window sills shall be laid in stepped manner with external sill level lower than internal sill level: No seperate payment shall be considered for stepped sill laying]

Granite of any colour and shade duly approved of 14 mm thick

Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.

Kota stone slab 25mm thick

Providing and fixing approved colour homogeneous 2 mm thick of single layered flexible anti static Vinyl flooring (spica of Tusker Vinyl Floorings) in roll form over I.P.S. / Kota stone flooring with approved adhesive, all joints to be soldered by PVC rods as per manufacturers specification etc. complete as per direction of Engineer-in-Charge including proper levels and cleaning. (Roll width minimum 2.0m, weight of P.V.C. flooring 90 kg/30 sqm. I.P.S. / Kota stone shall be paid seperately).

Providing and fixing approved colour homogeneous 1 mm thick wall covering capila of Tusker Vinyl in roll form over wall with approved adhesive, all joints to be soldered by PVC rods as per manufacturers specification etc. complete as per direction of Engineer-in-Charge including proper levels and cleaning.

Providing and laying 2mm thick antifungal self levelling Epoxy flooring on concrete substrate including covering at floor wall junction & including necessary surface preparation using cleaning, dedusting, levelling with cement mortar 1:4 (1 cement : 4 fine sand) of required thickness etc., applying suitable primer including Aisle or zone marking in different colours etc. complete as per manufacturers specifications and as directed by Engineer In Charge.

80 mm thick factory made c.c. interlocking paver block of M-35 Grade Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern.

SUB-HEAD : ROOFING AND CEILING WORK

Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in-charge.

0.50mm thickness

Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm:

0.50mm thickness

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45 x15 x 0.90mm running at the spacing of 1200 mm c/ c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing &

including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595 mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8 mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Coupler - 110mm

Single equal tee without door - 110 x 110 x 110 mm

Single equal tee with door - 110 x 110 x 110 mm

Bend 87.5 degree - 110mm

Plain shoe - 110 mm

Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete.

Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC rain water pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete as per direction of Engineer-in-charge.

SUB-HEAD : FINISHING WORK

12 mm cement plaster of mix

In cement mortar 1 : 4 ( 1 cement : 4 fine sand )

In cement mortar 1 : 6 ( 1 cement : 6 fine sand )

15 mm cement plaster on the rough side of single or half brick wall of mix:

Cement mortar 1:6 (1 cement : 6 fine sand)

6 mm cement plaster of mix:

In cement mortar 1 : 3 ( 1 cement : 3 fine sand )

Neat cement punning.

Extra for plastering exterior walls of height more than 10m from GL for every additional height of 3 m or part thereof complete.

Above 10m upto 13m

Above 13m upto 16m

Above 16m upto 19m

Above 19m upto 22m

Above 22m upto 25m

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :

New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:

New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Two Coats

Wall painting with premium anti-bacterial acrylic emulsion paint of interior grade, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour over and including priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

Two Coats

Finishing with Epoxy paint ( two or more coats) of approved brand and manufacture at all locations prepared and applied as per manufacturer's specification including appropriate priming coat, preparation of surface etc. complete [Payment shall be made after submission of Test Certificate issued by the Manufacturer].

On concrete wall / Brick wall

SUB-HEAD : WATER PROOFING WORK

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:

Kickers (320 mm wide, 5 mm thick)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :

Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size)

Providing, mixing and applying SBR polymer (of approved make @ minimum 2% by wt. of cement used) modified plain/reinforced cement concrete for structural members having minimum characteristic compressive strength [with ordinary portland cement, fine sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness and as per direction of the Engineer-in-charge. Note: Rates shall be for finished surface area of concrete and shall include the cost of labour, concrete and appropriate approved Super- Plasticiser for rendering concrete as flowable and SBR polymer but shall exclude cost of reinforcement, bond coat, Shear Keys, centering and shuttering, strutting, propping etc (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)

50mm thick in Grade M 25 with cement content not less than 418 kg per cum

SUB-HEAD : CRASH GUARD, CORNER GUARD, NAME BOARDS & SIGNAGES

Providing and fixing Hand Rail Crash Guard 140mm x 30 mm thick, aluminium retainer thickness 2 mm with uPVC snipfeet top 20mm thickness having ABS and Anti-bacterial.

Providing and fixing Corner Guard 1200mm x 15 mm thick, aluminium retainer thickness 2 mm with uPVC snipfeet.

Providing and fixing Corner Guard for columns at parking area size W 100 x H 800 x 8 mm colour black with yellow or white reflective stickers having body materials modified Themoplastics (Polymer Rubberized) fixed on wall & corner of column with six 2" screws

Providing & fixing Aluminium profile based Name boards as per required sizes with 3mm foam base & vynil letters, as per sample approved by Architects etc. all complete and asper fire exit norms & as per the design & instructions of Architect.

Signage Type 1- Providing & fixing signage plates made of anodized aluminium sections with computer grade vinyl lettering and polycarbonate sheet on top for protection of size 300 x 100 mm complete as per instructions and as directed and necessary graphic diagrams, symbols or matter, fastners etc of Engineer In charge.

Providing & Fixing in position signage board in aluminium extruded brown anodized section or as approved with etters in vinayl on one or both side covered with acrylic sheet as per approved sample by architect with required fitting, fixtures etc. including VAT, Excise duty, Octroi, service tax and other tax, duties charges levies loading / unloading transportation, installing etc all complete. Bed Number Size : 4" x 5"

SUB-HEAD : PLUMBING WORKS

Supply, Installation, Testing, and Commissioning of 2‐Bay Scrub Sink, with Infrared Photo sensor, Digital Timer with user defined Time interval 1, 3, 5 and 10 minutes,1 no. mixture valve and 1 No. solenoid valves along with Manual Option Foot Operated mechanism/ Foot switch. Anti‐splash metal body construction made of Stainless Steel Grade 304 polished finished. The Scrub Sink is provided with front access panel for maintenance and repairs. 1 – Position size 1600 mm long as per directin of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing SS grabbars set for accessible toilets comprising of 4 No. Grabbars as specified: (1NO. wing grabbar +1 NO. Lshaped grabbar + 2NO. straight grabbars=1 typical set) a) Swing grabbar (1NO) Providing a S.S.304 SWING HANDICAP GRABBAR- 700mm and of DIA:32MM and thickness 1.5mm of the roved brand and make. b) L Shaped grabbar (1NO) Providing S.S.304 LSHAPED DISABLED GRABBAR of SIZE-600MM(H)X600MM(D) and 32MM DIA .and thickness 1.5 mm of the approved brand and make. c) Straight grabbar (2NO) Providing S.S. 304 GRAB RAIL (600MM),32MMDIA. and thickness 1.5mm of the approved brand and make.

Providing and fixing White Vitreous China of 'Hindware & Parryware' make or equivalent under counter type Oval wash basin of size 550x 480mm with CI brackets suitable for mounting below granite counter including waste fitting with CP brass bottle trap, angle valve with CP connection etc. complete as specified. [Oval Wash Basin Hindware Model No. 10051 OR consider equivalent make].

Providing and fixing JAQUAR MAKE, PRESSMATIC Taps Model No. 031 Pillarcock Auto closing system etc complete.

Providing & fixing in position 'Jacquar Continental' make CPJet Spray with flexible CP supply pipe, and all other accessories, complete.

Providing & fixing 2-way Bib cock JAQUARMAKE, ORNAMIX Model No. 10041 etc. complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required :

Size 600x450x200mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe - 32 mm dia

Flexible pipe - 32 mm dia

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.

450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.

Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:

Coupler - 110mm

Single pushfit Coupler - 110 mm

Single equal tee without door - 110 x 110 x 110 mm

Single equal tee with door - 110 x 110 x 110 mm

Bend 87.5 degree - 110mm

Plain shoe - 110 mm

Double equal junction of required degree without door - 110x110x110 x110 mm

Double equal junction of required degree with door - 110x110x110 x110 mm

Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete.

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand):

100 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. - Internal work - Exposed on wall.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. - Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. - External work

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

62.50 mm nominal inner dia .Pipes.

75 mm nominal inner dia .Pipes.

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing brass stop cock of approved quality :

15 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

25 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end):

25 mm nominal bore - Vertical

40 mm nominal bore - Vertical

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length - 15 mm nominal bore

30 cm length - 20 mm nominal bore

45 cm length - 15 mm nominal bore

45 cm length - 20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:

100 mm diameter

Constructing masonry Chamber 30x30x50 cm, inside , in brick work in cement mortar 1:4 (1 cement :4 fine sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

With Second Class bricks

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms.

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete :

150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design:

150 mm diameter S.W, pipe

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 14.37 complete as per standard design :

For 500x700 mm size

Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8.

Providing weepholes in brick masonry / stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or PVC pipe (110 mm OD of 6.0 kg/cm^2 pressure) extending through the full width of the structures with slope of 1(V): 20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7.

SUB-HEAD : INTERNAL ELECTRIFICATION WORKS

Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required.

Wiring for 2 way controlling light point with 3x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type 2 way switch, cover plate, GI box including necessary connection etc. as required.

Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin etc. as required.

Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin etc. as required.

Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:-

2 X 1.5 + 1 X 1.5 sq mm

2 X 2.5 + 1 X 1.5 sq mm

2 X 4 + 1 X 1.5 sq mm

4 X 4 + 2 X 1.5 sq mm

4 X 6 + 2 X 2.5 sq mm

4 X 10 + 2 X 4 sq mm

4 X 16 + 2 X 6 sq mm

4 X 25 + 2 X 10 sq mm

4 X 35 + 2 X 10 sq mm

Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.

19/20 mm dia

25 mm dia

Supplying and fixing of the following electrical accessories including necessary connection etc. as required.

3mm thick bakelite sheet

Supplying and fixing of the following modular accessories including necessary connection etc. as required.

4 step fan regulator (1M):-

RJ11 telephone socket outlet (1M):-

RJ45 LAN socket outlet (1M):-

Louvers/opaque type LED foot lamp (4M):-

20/25 amps single phase motor starter switch (2M):-

Supply and fixing of 25mm x 5mm GI strip on wall/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals.

Supply and fixing of 32mm x 6 mm GI strip on walls/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals.

Supply and fixing of 25mm x 3mm Copper on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals.

Supply and fixing of 32mm x 6 mm Copper strip on walls/ floor of the building for hoizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals.

Suppying installation testing and comissioning of following of ESE (Early Streamer Emission) Materials i/c necessary connection etc as required

OPR-Early Streamer emission (ESE) Lighting protection airterminal should complies with OPR 60 Level II (63 Mtr - 5Mtr Height) (make ABB/ERICO/DEHN)

Mounting Mast to hold early streamer emission OPR 60, of robust design with mounting mast of 2 met to couple OPR (make ABB/ERICO/DEHN)

Mounting Mast of 3 met with base plate and guy wire (Make ABB/ERICO/DEHN)

Lightning stroke counter(Make ABB/ERICO/DEHN)

17.2 mm Copper bonded earth rod 3 met tested with IEC 62561 (Make ABB/ERICO/DEHN)

25 kg bag of Ground Resistance Improvement Compound Fursecem powder (Make ABB/ERICO/DEHN)

Rod to tape clamp (25 x 3 tape to 17 mm rod) of copper alloy (Make ABB/ERICO/DEHN)

Inspection pit cover plate with IEC 62561 (Make ABB/ERICO/DEHN)

Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in existing PVC Casing Capping/ conduit in recess/surface including connection etc. as required:-

1 x 70 sq mm PVC Insulated copper conductor cable

Providing earthing system with maintenance free earthing electrode of 50 mm dia & 3 mtr long of dual electrode technology filled with highly conductive compound and back fill compound of 2 nos. 25 kg bag, terminal size 32mmx 6mm including accessories with masonry enclosure of CI cover plate size 12"x 12" having locking arrangement including CC works etc as required:-

Supplying & fixing of 900 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) :-

Supplying & fixing of 1200 mm sweep white color AC ceiling fan with brush less dirrect current (BLDC) motor having class B insulation, power factor not less than 0.9 complete with 300 mm down rod, canopies, shackle kit, 3nos blades, safety rope including wiring the down rod with 2x1.5 sqmm PVC insulated copper conductor cable(FR) (BEE 5 star/minimum service value 6.0 m3/min/W & tolerance as per IS:374-2019) : -

Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:-

Supplying & installation of 300 mm sweep metalic body exhaust fan including connection etc as required:-

Supplying & installation of 380 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) :-

Supplying & installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required:-

Supplying & installation of shutter for 380/450 mm sweep metalic body exhaust fan in the existing hole as required:-

Supplying & installation of metalic fan clamp box of standard size with 3mm thick bakelite/plastic cover as required:-

Supplying and fixing of 20 mm dia extra down rod (GI Pipe Medium Guage) with necessary hole for installation of ceiling fan as required.

Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc as required:

Supplying and fixing of following vertical storage water heater 5 star catagory complete with 15 amps top, connection pipes including necessary connection etc as required.

15 litre storage capacity:-

25 litre storage capacity:-

Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-

Surface mounted integrated 10 watt LED batten with polycarbonate diffuser:-

Surface mounted box type batten suitable for single 18/20 watt integrated LED tube lamp (without lamp):-

Recessed/Surface mounted 2ft x 2ft decorative 36 watt LED panel light with integral driver and high quality polycarbonate diffuser:-

Recessed round/Square shaped 15 watt LED downlight with integral driver and high quality polycarbonate diffuser:-

Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-

90 watt LED street light fixture with integral driver and secondary lens (IP 66):-

9 watt/10 watt LED Bollard light with high quality polycarbonate diffuser (IP 65):-

Supplying and fixing of 70 mm top dia, 130 mm bottom dia, 3 mm thick hot dip galvanized 7 mtr long octagonal pole of base plate 220x220x12- mm with 1000 mm long single/double armed bracket with 70 mm top and foundation bolt and template etc. as required.

Single armed bracket

Double armed bracket

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size):-

Centering shuttering including struttings, propping etc. and removal of form work for: Foundations, footings, bases for columns etc. for mass concrete with timber plank:-

Supplying & installation of 900mmx600mmx300mm floor mounted powder coated weather proof outdoor metal cabinet made of 16 gauge MS sheet supported with 4 nos legs made of 40mmx5mm MS angle complete with single door with locking arrangemet as per dirrection of site engineer:-

Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:-

18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100lm/watt):-

9 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :-

Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.

(2+10) / 12 way SPN MCB DB (double door):-

8 way horizontal TPN MCB DB (Double door):-

12 way horizontal TPN MCB DB (Double door):-

Supplying and installation of powder coated steel sheet enclosure for 415 volts MCCB (TP/FP) complete with necessary connection etc as required:-

Enclosure suitable for MCCB above 100 amps upto 250 amps:-

Supplying, installation, testing & commissioning of powder coated prewired panel board suitable for 415 volts TP MCCB as incomer & outgoing including busbar & connection as required of the following ratings & sizes:-

6 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

8 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

12 way TP MCCB outgoing & TP MCCB incomer upto 400 amps:-

Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-

6 to 32 amps SP MCB:-

6 to 32 amps DP MCB:-

40/50/63 amps FP MCB:-

Supplying & installation of TP/FP MCCB of following ratings in the existing MCCB enclosure/ panel board including connection etc as required (Ics=100% of Icu with adjustable settings):-

16 to 100 amps TP MCCB, Breaking capacity 16/18KA (Thermal Magnetic):-

125 amps TP MCCB, Breaking capacity 25KA (Thermal Magnetic):-

160 amps TP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-

200 amps TP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-

250 amps TP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

320 amps TP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

400 amps TP MCCB, Breaking capacity 36KA (Thermal Magnetic) :-

Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required

3.5 core 4 Sq mm

3.5 core 6 Sq mm

3.5 core 10 Sq mm

3.5 core 25 Sq mm

3.5 core 35 Sq mm

3.5 core 50 Sq mm

3.5 core 70 Sq mm

3.5 core 95 Sq mm

3.5 core 150 Sq mm

3.5 core 185 Sq mm

3.5 core 240 Sq mm

3.5 core 300 Sq mm

4 core 4 Sq mm

4 core 16 Sq mm

4 core 25 Sq mm

4 core 35 Sq mm

4 core 50 Sq mm

4 core 70 Sq mm

4 core 95 Sq mm

4 core 120 Sq mm

4 core 150 Sq mm

4 core 185 Sq mm

4 core 240 Sq mm

4 core 300 Sq mm

Supplying and laying of following sizes XLPE insulated PVC sheathed copper conductor Un-armoured cable including necessary connection etc as required.

3 core 1.5 Sq mm

Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -

Supplying and fixing of heat shrinkable cable end termination kits of following sizes : -

2 core 16 sq mm or 4 core 10/16 sqmm size:-

3.5 core or 4 core 240/300 sqmm size:-

Supplying and fixing of thermoplastic cable junction box with connectors suitable for following sizes cable : -

1.5 sqmm - 4 sqmm Cable:-

4 sqmm - 10 sqmm Cable:-

Excavation of earth for cable trench of 800mm depth & 300mm width in all kinds of soil including back filling of cable trench with the excavated soil with 20cm layer of sand, 3.5 nos bricks per metre for protection including ramming, consolidating to the original shape as per dirrection of Site Engineer :-

Drawing of armoured/un-armoured cable with proper saddling etc as required:-

Supplying and fixing of following Cable tray made of hot dip galvanised iron:-

30 mm x 50mm, 2mm thick

54 mm x 100 mm, 2mm thick

105mm x 150mm, 2mm thick

70mm x 300 mm, 2.5 mm thick

70mm x 450 mm, 2.5 mm thick

70mm x 600 mm, 2.5 mm thick

70mm x 750 mm, 2.5 mm thick

70mm x 1000 mm, 2.5 mm thick

LT PANEL Supplying, installation, testing & commissioning of cubical type, extensible, bolted construction TTA LT Panel as per IEC-61439-1&2 test61439-1&2 , IAC as per IEC-61641 for 50KA for 0.3 sec. Panel shall be supplied with a double door arrangement. Global Door/ glass door IK10 tested shall be provided as front door to allow maintenance staff to visually access device status, meter readings, indicating lamp status without opening the door ,IP54 ingress protection when door closed, IP20 protection in door open condition.Global door shall be provided with Ergonomic handles with locking (key RONIS n° 405). Panel shall be suitable for 415 V, 3 Phase, 4 wire 50 Hz AC supply system of suitable size fabricated in compartmentalized design, made of CRCA sheet steel of 2mm thick , 3mm thick for gland plates i/c cleaning & finishing complete with 9 tank process for powder coating in approved shade,the frame shall be of bolted design made of Galvanized iron with 9 fold structure for better rigidity and strength with 275GSM ( no welding frame to be considered) , having 2000 Amp capacity extensible type TPN Aluminium bus bars with colour coated heat shrinkable sleeves,moulded type busbar insulator ( FRP insulator not acceptable)with short circuit withstand capacity of 50KA for 1 Sec.,maximum height of the panel shall be limited to 2231mm bottom base channel of MS section not less than 100mm x 50mm x 3mm thick. Fabrication shall be done in trasportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5 Sq.mm FRLS . PVC insulated copper conductor S/C cable for voltage & Current respectively, cable alleys, cable gland plates in two half, i/c providing following switch gears : Panel shall be provided with QR scanner code to log the SLD of the panel digitally and all the catalogue of the equipement installed inside the panel.

Outgoing Incomer : 433V (Uimp=12KV peak), Icu@433V=Ics=Icw for 1 sec =50KA, 800A EDO type 4P Air Circuit breaker with break time (<40 mili sesond) , manual draw out type with microprocessor based LSIGN release having adjustable overload with alarm indicator and time delay, short circuit with time delay, Instantaneous current, Earth fault with time delay and adjustable neutral protection - N, N/2, OFF, test facility and inbuilt Metring for Current-, last 10 trip history, breaker ageing data with Spring Charge Signal Switch, reday to close contact, ; comprising of at least 5 current settings in LSIG and 5 time settings in LSG, ACB shall have Undervoltage release. ready to close indication shall be provided with breaker . ACB shall have Undervoltage release, both side spreader links. Breaker should be compatable type with 3rd party SCADA / Energy monitoring system..... 02 Nos (01 for HVAC System & 01 No for Spare) Each set comprising of 1 no. 400 A Icu=Ics=36 kA FP VTVM MCCB with O/L (70%-100%) In,S/C release 5-10 In with Aux Contact for On/Off/Trip/ with extended rotary Operating Handle' & 'Door Interlock. 1.- Indicating lamps ON/OFF/TRIP),Set of Control MCB & accessories as required....complete 14 sets. Each set comprising of 1 no. 315 A Icu=Ics=36 kA FP VTVM MCCB with O/L (70%-100%) In,S/C release 5-10 In with Aux Contact for On/Off/Trip/ with extended rotary Operating Handle' & 'Door Interlock. 1.- Indicating lamps ON/OFF/TRIP), Set of Control MCB & accessories as required....complete 06 sets. Each set comprising of 1 no. 200 A Icu=Ics=36 kA FP VTVM MCCB with O/L (70%-100%) In,S/C release 5-10 In with Aux Contact for On/Off/Trip/ with extended rotary Operating Handle' & 'Door Interlock. 1.- Indicating lamps ON/OFF/TRIP), Set of Control MCB & accessories as required....complete 03 sets.

RISING MAIN AND PLUG IN BOX Supplying, installation, testing and comissioning of indoor sandwitch Rising main system which shall be light weight low impedance non ventilated naturally cooled and totally enclosed in a housing of 1.6 mm electrogalvanized sheet with an epoxy powder coated paint finish for protection against mechanical damages and dust accumulation, compact and sandwich type with degree of protection IP 54 For each rising main lengh and fitting fire stop or barriers shall be included as an integral part while on both internal and external surface, metal trunky shall be galvanised with epoxy powder coated by an automated electrostatic process the Busbars shall be insulated throughout their length by epoxy coating, the insulating material shall be of class-H 180 Degree C Joints shall be checked for tightness with de-energising the busbar trunking runs, and shall be maintenance free system of 1 bolt type with throw bolts The Bus duct shall be provided with fire barriers at each of the floor with 4 Hours fire ratings The Plug in box shall have suitable space for terminating XLPE Armoured aluminium cables of sizes ranged from 3.5 C / 4 C x 25 Sqmm to 240 Sqmm The Horizontal Bus duct shall be supported by GI Hangers at every 1.5 meters. The vertical bus duct shall be supported by Spring Hangers not more than 3mtrs Apart The rate shall include all allied and implied items required for complete commissioning of the system

B) PLUG IN HOLE Plug in openings shall be 3 nos on every 3000mm straight lenghth spaced at every 650mm a) Lighting Rising Main Bus Duct Run from Lower Ground Floor 2 to Third Floor Rating in AMPS: 160A Conductor: High Conductivity Al Service: Indoor Short Cicuit rating: 35kA Impedance value: As per IS The Rising Main Bus Duct shall be provided with Class F type insulation and thickness 1.6mm Construction: 3phase 4 wire with 50% neutral and 2R of 50 x 10 mm Al strip through out the length of bus duct for earthing

b) Power Rising Main Bus Duct Run from Lower Ground Floor 2 to Third Floor Rating in AMPS: 250 A Conductor: High Conductivity Al Service: Indoor Short Cicuit rating: 35kA Impedance value: As per IS The Rising Main Bus Duct shall be provided with Class F type insulation and thickness 1.6mm Construction: 3phase 4 wire with 50% neutral and 2R of 50 x 10 mm Al strip through out the length of bus duct for earthing

c) UPS Rising Main Bus Duct Run from Lower Ground Floor 2 to Third Floor Rating in AMPS: 200 A Conductor: High Conductivity Al Service: Indoor Short Cicuit rating: 35kA Impedance value: As per IS The Rising Main Bus Duct shall be provided with Class F type insulation and thickness 1.6mm Construction: 3phase 4 wire with 50% neutral and 2R of 50 x 10 mm Al strip through out the length of bus duct for earthing

C) PLUG IN BOX The plug in box shall be with safety lock: Plug in units rated 400A and below shall be mechanically interlocked with the bus duct housing to prevent the installation of removal of Plug in units while the switch is in the ON Position. The plug shall have suitable space for terminating armoured aluminium cables of Sizes ranged from 3.5C/4C x 25sqmm to 240 Sqmm

Lighting Rising main Plug in box - With Moulded case circuit breaker: 4 pole 160A

Power Rising main Plug in box - With Moulded case circuit breaker: 4 pole 250A

UPS Rising main Plug in box - With Moulded case circuit breaker: 4 pole 200A

D) SITC of Tap Up Box MT in Sandwich busbar

FIRE ALARM AND DETECTION SYSTEM

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 3 Loop Fire Alarm control panel . Panel shall be running on full digital protocol with 32 bit Microprocessor . The Panel shall be complete with 6" color touch screen LCD Display with 690 characters. Each addressable loop shall be capable of taking 250 addresses per loop configuring either as all detectors or modules or any mix of both. The system shall be polarity insensitive and 4000 event memory. The panel shall support degrade mode operation or shall have redundant CPU and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition. (make: Siemens/Simplex/Notifier)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable multi-criteria detector (optical and thermal sensors) complete with standard base, facility to mount in different comprehensive environment, Tri-color detector-status LED with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in detector shall consider Isolator base in place of standard base OR separate Isolator before and after every detector to comply the same without any extra cost. (Make: Siemens/Simplex/Notifier)

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual Pull Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), T-45 Key Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC and <=95%. MCP shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every MCP to comply the same without any extra cost. . (make: Siemens/Simplex/Notifier)

SITC of Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and 75cd flashintg at 1 Hz for visual indication. . (make: Siemens/Simplex/Notifier)

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same without any extra cost. (For AHU & Staircase Pressurization Fans, Hooters / Sounders / Strobes etc.). (make: Siemens/Simplex/Notifier)

Supplying and fixing of 2 x 1.5 sqmm Round flexible (FRLS) wire with necessary connection etc as required

Supplying & laying of UTP CAT 6, 305 meters,Core diameter: 0.565mm,OFC,CM,orange (Make: HIKVISION /Derwiser/ D-link)

Supplying & laying of 6 core SM mode Fibre optics cable. (Make: Any renouned brand with ISO/IEC-1180, 9/125u, OS2 Outdoor, as per ITU/T 652D. BELLCORE GR 20 / IEC 794-1, Qualifies as per ICEA-640. & BIS certificate that ensures that the product is technically sound) (Make: Finolex/Opterna)

SUB HEAD : MECHANICAL WORKS

MEDICAL GAS PIPE LINE SYSTEM OXYGEN SYSTEM

Providing and fitting, fixing Oxygen main manifold of size 10 + 10 cylinders complete with middle frame with chain for individual cylinder alongwith tail pipe ,NRV for every cylinder and isolation valve,safety valve etc. as required for the complete manifold system as per standards.

Providing and fitting, fixing Oxygen emergency minor manifold of size 2 + 2 cylinders complete with middle frame with chain for individual cylinder alongwith tail pipe ,NRV for every cylinder and isolation valve,safety valve etc. as required for the complete manifold system as per standards.

Providing and fitting, fixing of fully automatic Control panel for Oxygen having constant delivery flow capacity of minimum 1000 lpm at 4.2 bar pressure as per standard.

Providing and fitting, fixing of high flow Oxygen regulator for emergency minor manifold.

Oxygen Flowmeter & Humidifier Bottle with matching adapters: Back Pressure Compensated Flow meter within a range of 0-15 LPM where 0-5 LPM should be with expanded scale. Humidifier bottle should be made of unbreakable polycarbonate materials and autoclavable at 121 degree Centigrade (to be supplied along with required low pressure tubing and face mask) as per standard

Providing and fitting, fixing of surface/panel.pendant mounted front loading double lock Oxygen Outlets with matching Adapter (BS Type) as per standards

MEDICAL AIR SYSTEM

Providng and installation of Compressed Air system complete with 10 HP reciprocating motor with isolation valve as per technical specifications and terms and conditions.

Providing and erection of 1000 Litres capacity vertical air receiver with safety valve

Providing, fitting, fixing, testing and commissioning of duplex 4 stage air filtration system as per ISO 8573.1

Providing and fitting, fixing of air dryer system.

Providing and fitting, fixing of control panel for Air compressors.

Providing and fitting, fixing of surface/panel.pendant mounted front loading double lock medical Air 4-bar Outlets with matching Adapter (BS Type)

Providing and fitting, fixing of output pressure regulator system with 2 regulators with gauges, 4 isolation valves, and inter connecting piping.

HP colour coded black tubing having anti static core as per ISO standards.

VACUUM SYSTEM

Providing and installation of 5 HP vacuum pump each having piston displacement with filter..

Providing and erection of 1000 Litres capacity Vacuum receiver.

Providing and fitting, fixing of control panel for Vacuum system.

Providing and fitting, fixing of surface/panel/pendant mounted front loading double lock Vacuum Outlets with matching Adapter (BS Type) and necessary accessories.

Providing and fitting, fixing of Ward vacuum Unit : It shall include vacuum regulator along with 0-760 mm of Hg vacuum gauge,600 ml capacity reusable poly carbonate collection bottle with overflow safety trap and autoclavable at 121 degree Centigrade with plastic slide wall mounted type (to be supplied along with required low pressure tubing with catheter).

Providing and fitting,fixing of Theatre Vacuum Unit: It shall be trolley mounted. The unit shall include one regulator along with 0-760 mm of Hg vacuum gauge mounted on the trolley stand, having two reusable collection bottles each of 2000 ml capacity and made of unbreakable polycarbonate materials, autoclavable at 121° Centigrade, having over flow safety trap, mounted on the base of trolley unit made of aluminium along with castor wheels and connected with regulator & low pressure tube inter-connections (along with required low pressure tubing with catheter).

HP colour coded yellow tubing having anti-static core as per ISO systems.

LP Tubing having anti static core as per ISO standards

NITROUS OXIDE SYSTEM

Providing and fitting, fixing of control panel for N2O 4 manifolds.

Providng and fitting, fixing of N2O manifold 4 + 4 cylinder.

Providing and fitting, fixing N2O emergency minor manifold of 1 + 1 cylinder.

Providing and fitting, fixing of surface/panel/pendant mounted front loading double lock Nitrous Oxide Outlets with matching Adapter (BS Type) and necessary accessories.

Providing and fitting, fixing of high flow N2O regulator for emergency minor manifold.

Pipeline accessories

Providing and fitting, fixing area alarm electronic control:

For 2 gases-Oxygen & Vacuum.

For 3 gases- Oxygen, N2O & Vacuum.

For 4 gases-Oxygen, N2O, Air & Vacuum.

Providing and fitting, fixing of Area valve service unit with Nist Connector as per standard.

2 gas valve box configuration with size 15 O2, 22 VAC

3 gas valve box configuration with size 15 O2, M AIR 22 VAC

2 gas valve box configuration with size 15 O2,15 N2O M AIR 22 VAC

Providing and fitting, fixing of coversion kit with 5 m long pipe:

For Oxygen

For Nitrous Oxide

For Air

For Vacuum

Providing and fitting, fixing of low pressure pipe for vacuum.

Providing and laying of Medical Grade Copper pipe (As per EN-13348 and relevant ASTM) of different diameters in the different systems:

Copper pipe, 12 mm dia.

Copper pipe, 15 mm dia.

Copper pipe, 22 mm dia.

Copper Pipe, 28 mm dia.

Copper Pipe, 42 mm dia.

Copper pipe, 54 mm dia.

Providing and fitting, fixing of isolation valve assembly of different diameters with fittings in the Different systems:

Isolation valve assembly with fittings, 12 mm dia

Isolation valve assembly with fittings, 15 mm dia

Isolation valve assembly with fittings, 22 mm dia

Isolation valve assembly with fittings, 28 mm dia

Isolation valve assembly with fittings, 42 mm dia

Isolation valve assembly with fittings, 54 mm dia

FIRE PROTECTION SYSTEM

SITC of ISI marked Providing & Fittingfixing of CO2 Fire Extinguisher 2 kg capacity Cylinder.

SITC of ISI marked CO2 gas type Fire Extinguisher of of 4.5 kg capacity made from seamless cylinder with control valve,fitted with discharge adopter, complete with initial gas charge, carrying handle and wall mounting bracket etc. as complete as required.

SITC of ISI marked ABC stored pressure type Fire Extinguisher of 6 kg capacity of welded cylinder squeeze lever discharge valve fitted with pressure gauge with initial discharge tube discharge hose and nozzle suspention bracket charged with mono amonium phosphate base ABC powder and pressuirsed with nitrogen gas etc. as complete as required.

Providing & Fitting fixing of Dry Chemical Powder (DCP) Fire Extinguisher 6 kg capacity Cylinder.

SITC of ISI marked Providing & Fittingfixing of AFFF Fire Extinguisher.

SLFTC of M.S. Pipes on surface Supplying, Laying, Fixing, Testing & commissioning of following sizes (NB)of ISI mark heavy class TATA/ JINDAL M.S pipes including cutting threadingwelding etc. and providing all fittings e.g. Elbows. Reducers. Clamps, Hangers, Flanges, Gaskets. Nuts& Bolts cost including providing two coats of synthetic enamel paints of approved shades over a coat of primer. prior to application to primer the surface should be clean for any dirt, rusts, rough substance etc. including painting of legends of both direction arrow asper approval of the project manager.

200 mm dia (wall thickness 6.3 mm)

150 mm dia

100 mm dia

80 mm dia

40 mm dia

25 mm dia

150 mm dia (underground pipe line..etc).

Providing and fixing internal fire hydrant comprising of SS Fire Hydrant Valve 80 mm inlet with single headed with single outlet with control and fitted with63mm dia instantaneous female coupling on the outlet complete with orifice flange as required, blankcap and chain locations as per drawings (inlet flanges to I.S 5290-1977 class C.

S/I/T/C of electric motor driven automatic pressurization pump (JOCKEY FIRE PUMP)consisting of : (Kirloskar / mather platt make) suitable for discharge of 180 LPM at a total head of 55M. Common base plate fabricated out of MS Channel Suitable pump foundation with vibration damping arrangement by cushy foot or similar mountings as required 180LPM @55m Head.

180 lpm at 55 m Head.

S/I/T/C of Electric Motor Driven Fire pumping (Sprinkler pump) set (Kirloskar /Mather platt make)suitable for automatic operation consisting of thefollowing for delivery of 2280LPM at a total head of 55M so as to ensure aminimum pressure of 3.5kg/sq.cm at highest andfarthest outlet of the specified flow and minimum 5.50kg/sqcm at the pump outlet. Commonbase plate fabricated out of MS channel Suitable pump foundation with vibrationdamping arrangement by cushy foot or similarmountings as required.

1620 LPM @55m Head.

S/I/T/C of Diesel Engine Driven Fire pump suitable for automatic operation consisting of the following and Part V-1985 and relevant BISspecifications. i) Horizontal Split casing centrifugal pump suitable for delivery of 2280LPM at a total head of 55M so as to ensure a minimum pressure of 5.50 Kg sq cm at the Suitable cement concrete foundation with vibration damping arrangement and cushy foot mounting as required.

1620 lpm at 56 m Head

S/I/T/C of Electric Motor Driven Fire pumping (Hydrant pump) set (Kirloskar/Mather platt make) suitable for automatic operation consisting of the following for delivery of 2280LPM at a total head of 55M so as to ensure a minimum pressure of 3.5kg/sq.cm at highest and farthest outlet of the specified flow and minimum 5.50kg/sqcm at the pump outlet. The pump shall be of horizontal End suction type with cast iron body, bronze impeller and stainless steel shaft directly coupled through a flexible coupling with electric motor. Common base plate fabricated out of MS channel of size 75 x 150mm iv) Suitable pump foundation with vibration damping arrangement by cushy foot or similar mountings as required 1620LPM @55m Head.

Sluice valve 150mm

Providing and fixing butterfly valve confirming to type P.N.1.6 of IS 13095-1991 complete with flanges, bolts, nuts, gasket etc. as per specifications complete in all respect hydraulically tested to 20kg/sqcm.

150 mm dia.

100 mm dia.

80 mm dia.

65 mm dia.

50 mm dia.

Providing and fixing cast iron double flanged horizontal type with gunmetal seat non-return valve confirming to class - I of IS : 5312 including nuts, bolts, 1.5 mm thick compressed asbestos gasket including painting complete.

150 mm dia .

100 mm dia.

65 mm dia.

Providing and fixing standard short sizeSS branch pipe with gunmetel nozzle 16mm dia outlet with standard male instaneous spring lock type 63 mm dia coupling. Branch pipe and nozzle shall confirm to IS : 903-1985.

Stainless Steel (Grade 304).

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. forsuitable dia MS pipe connection conforming to IS 904 as required.

4 way - 150 mm dia M.S. Pipe

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories.

Pendent Sprinkler

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith syntheticenamel paint of approved shade as required.

Providing and fixing first aid fire hose reel equipment confirming to IS : 884-1969 with up to date amendments finished with post office red spray paint and complete with following as required : (i) 20mm dia. 36.5 meters long hose tubing of approved make confirming to IS : 5132- 1969 with up to date amendments. (ii) Swinging type hose guide fixing bracket assembly (iii) 25mm dia gate valve (iv) 6mm outlet SS nozzle with shut off valve as required.

Providing and fixing 63 mm dia 15 m long Reinforced Rubber lined (RRL) woven jacketed hose tested to bursting pressure 32 kg/sqcm including gunmetal male and female instantaneous type-coupling approved by fire authority, machine would with G.I wire complete in all respects. Hose shall conform to I.S 636 Type II and coupling to I.S 903-1985 WITH ISI certification.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. asrequired.

Providing & fixing of pressure gauge in M.S. pipe line including connection etc. asrequired.

Providing & fixing of Double Door Hose Box with 12 swg and Fiber glass at front with key case.

Supplying and fixing air vessel made of 250mmdia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories,pressure.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mountedin M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing and commissioning of 25 mm ball valve.

Supplying, installation, testing and commissioning of half inch ball valve.

Supplying, installation, testing andcommissioning of foot valve.

150 mm dia.

100 mm dia.

Supplying, installation, testing & commissioning of manual call boxes ofMS construction in surface/recess with stainless steel chain & hammer.

Supplying, installation, testing &commissioning of hooter.

Supplying, installation, testing & commissioning of auto pump controller.

Supplying, installation, testing & commissioning of air release valve is typically used in water or irrigation schemes to ensure that any entrained airin the water system is automatically released in order to maximize thesystem performance.

Design, Supply, installation, testing and commissioning of CO2 Gas fire suppression system with CO2 cylinder and required length of automatic bursting tube inside LT panel as required for installation of complete system along with the complete items as per the specificaion, approved make, asper site.

Air Cooled Screw Chiller

Type of Compressor : Screw Compressor enclosure: Semi-hermetic Type of Refrigerant : R134a Compressor: Multiple Independent refrigeration circuits: Multiple Pre-coated fins for condenser coil :Not Required Third party BMS Compatibilty: BACNET/MODBUS Unit mounted starter: Star delta VFD for compressors: Not required Chiller plant manager - Required (Shall be suitable for Variable primary operation) Low noise condenser fans :Required Single Point Disconnect switch:Required Approval: ARI standard 550-92/Eurovent certified Evaporator Fouling Resistance: 0.0005 (FPS Units) Chilled Water Leaving the Evaporator : 7 Deg C Chilled Water Entering the Evaporator : 12 Deg C Ambient Conditions (summer): 37.8 DB/28.3 deg C WB C.O.P at ARI condition >or=2.8 Flow : 267 USGPM Operation: 2 Working+ 1 Standby Refrigeration load: 100 TR

Chilled Water Pumps - Variable / Constant Primary

Factory mounted centrifugal Back pull out / Inline chilled water pump with electric Motor on a common base, suitable for 415±10%, 50 Cycle and all basic components, Couplings, Coupling guard, Stainless steel shaft, Bronze impeller, Mechanical seal, Bronze shaft sleeves and wearing rings,bearings, Foundation bolts, Inertia Base, Nuts, Supports and Corrosion-resistant finish etc. & all necessary accessories as per relevant std. Pumps shall be insulated with Insulation of same material & thickness as the connected pipe. Aluminium cladding shall be provided for the insulation. VFD to be supplied by pump manufacture as per required quantity for Block 1 & Block 2. The pump shall vbe with necessary Logic controller, DP sensor & Control panel. Minimum Motor Efficiency shall be 70% Types of pump: End Suction "USGPM: 267 Head: 50m (Variable pump)" Working: 2 Stand By:1 Types of pump: End Suction

Closed Expansion tank with pressurising unit

Tank shall be precharged steel expansion tank with replaceble heavy duty butyl rubber bladder complete with necessary panel having complete accessories as pumps (1W+1S) system, pressure switch/sensors, makeup water tank with float valve. Tank shall have 50 mm connection & 20 mm drain and charging valve connection Tank 500 litres capacity. Max operating pressure:16 bar

Centrifugal Air Separator

Air Separator shall have required flange connections for the pipe connection. It shall be insulated with the same material of chilled water pipe. Header size:150 mm dia Chilled water Flow: 694 USGPM

Insulation for Buried Chilled water pipes with 50/75 mm thick Expanded Polystyrene of minium 16 kg/m3 density, TF quality, black polythene sheet covered with 24G chicken wire mesh & finished with 12mm thick sand cement plaster and 2 layers of bituminous tar felt. Dia 150mm -75mm thick

Valves

Cast iron butterfly valve complete with gaskets, flanges etc., PN 10 class rating. Valve shall be insulated as per specifications.

150 mm dia

100 mm dia

Motorised modulating globe Valves two way type with extended neck/spindle, matching flanges, hot dipped galvanized bolts and nuts Including insulation. Valves should be rated for PN 10-pressure rating for chillers safety bypass.

100 mm dia

Gun metal screwed type balancing valves for sizes upto 80 mm dia. and Cast iron flanged type for sizes 100 mm & above & PN 10 Class rating. Valve shall be insulated as per specifications.

125 mm dia

100 mm dia

Y-Type Strainer complete with Cast Iron Valve body, Flanges, Bolts, Nuts, Gaskets, Filter, Mesh less than 20, 1.6 mm thick Screen, PN 16 rating. Valve shall be insulated as per specifications.

150 mm dia

125 mm dia

Rubber Bellows PN 16 rating for primary pumps

100 mm dia

150 mm Dial type pressure gauges 0-10 bar range with Ball Valve

150 mm Dial type Temperature Gauge 0-50 deg. range.

Drain with standard ball valves PN 16 rating.

Air Purge valves

PN 16 rating.

AIR HANDLING UNITS (AHU) - TYPE 1

(1) 30.0 TR & 10000 CFM; 125 mm Static Pressure - 8 row coil.

(2) 14.0 TR & 4500 CFM; 125 mm Static Pressure - 8 row coil

(2) 11.0 TR & 3600 CFM; 125 mm Static Pressure - 8 row coil

AIR HANDLING UNITS (AHU)-TYPE 2

CEILING SUSPENDED AIR HANDLING UNITS

(1) 8.0 TR & 3050 CFM; 45 mm Static Pressure - 6 row coil,

(2) 9 TR & 3400 CFM; 40 mm Static Pressure - 4 row coil,

(3) 11 TR & 3600 CFM; 45 mm Static Pressure - 4 row coil,

(4) 6 TR & 2000 CFM; 45 mm Static Pressure - 4 row coil,

(4) 5 TR & 1600 CFM; 45 mm Static Pressure - 4 row coil,

(4) 4 TR & 1300 CFM; 45 mm Static Pressure - 4 row coil,

(4) 3 TR & 1100 CFM; 45 mm Static Pressure - 4 row coil,

TREATED FRESH AIR UNITS (TFA)

Double skin 50mm thick Ceiling suspended Air handling units with Fresh air & Supply air damper wih canvass connection, Cleanable Pre-filter with 90% efficiency down to 10 micron, 8 RWD Copper tube cooling coil with Aluminum fins, Supply fan with backward blade, necessary electrical and control panel, drain pan, control panel,etc. Motor shall be suitable for 415V+/-10% V & 50Hz AC supply. Noise level should be less than 70dbA at a distance of 1m from the unit. Heater banks shall be controlled by Thyristor controller. (a) Thermal break profile: Required (1) 4.0 TR & 1400 CFM; 50 mm Static Pressure - 8 row coil,

Fan Coil Units (FCU)

Chilled water type horizontal Fan Coil Units (FCU), Blow through type with 3R cooling coil, Cleanable fabric filter, main condensate extended insulated SS drain pan, Thermal overload protection & permanently lubricated 6 Pole motor suitable for 220+/-6V, 50 Hz, forward curved double width centrifugal fan, completed with factory fitted 2-way on/off Motorised valve complete with modulating actuators, thermostat and control wiring, ball valve with strainer, ball valve without strainer, balancing valve, drain pipe provision and necessory supports.

Providing & Installation & commissioning of Ventilation system of following required flow rate , appropiate fan diameter and efficiency, permissible noise level as per standard, minimum Outlet velocity 5.41m/s of appropiate rating installed in a insulated weather proof enclosure (3000 x1200 x 925) with pannel thickness 48 mm in/c intake suction, pre filter(MERV-8), Bag type fine Filter, (MERV-13), Motor(IE-2), Spring Isolator, Hepa Filter(MERV-17) etc.complete as per direction of the Engineer in charge to maintain negetive pressure as per requirement.

minimum 1000 CFM, 80 Static PR(mm wg)

minimum 2000 CFM, 80 Static PR(mm wg)

Providing & Installation & commissioning of Variable frequency Device for speed controlling of Ventilation system etc.complete as per direction of the Engineer in charge.

Providing ,installation & commissioning of Room pressure Gauges for measuring of negative & possative pressure of the room etc.complete as per direction of the Engineer in charge.

CHILLED WATER PIPING WITH INSULATION-EPS

Chilled water Mild steel pipes (Medium Class) with all necessary fittings like bends, elbows, tees, reducers, hanger, supports, etc and shall be as perlS 1239 upto 150mm dia and as per IS 3589. for 200mm dia & above with Insulation of chilled water pipes with EPS of 24 kg/Cu.m density, TF quality, covered with 24G GI mesh, 250 microns black polythelene sheeet and with GI Pre-coated sheet cladding.

Dia 20mm - (50 mm thick)

Dia 25mm (50 mm thick)

Dia 32mm (50 mm thick)

Dia 40mm-(50 mm thick)

Dia 50mm (50 mm thick)

Dia 65mm (50 mm thick)

Dia 80mm (50 mm thick)

Dia 100mm (50 mm thick)

Dia 125mm (50 mm thick)

Dia 150mm-(75 mm thick)

Valves

Cast iron butterfly valve complete with gaskets, flanges etc., PN 10 class rating. Valve shall be insulated as per specifications.

Dia 50mm

Dia 65mm

Dia 80mm

Cast iron ball valve with strainer complete with gaskets, flanges etc., PN 10 class rating. Valve shall be insulated as per specifications.

Dia 32mm

Dia 40mm

Cast iron ball valve without strainer complete with gaskets, flanges etc., PN 10 class rating. Valve shall be insulated as per specifications.

Dia 32mm

Dia 40mm

Pressure Independent Balancing & Control valve (PIBCV) with Test plugs The valves and actuators for AHU's shall be compatible with BMS. Actuatiors shall be suitable to receive 0-10V or 4-20 mA signal from BMS,complete with thermostat & control wiring, Flanges, Bolts, Nuts, Gaskets &/ PN 10 rating. Valve shall be insulated as per specifications. Also, the actuator shall work based on thermostat. The thermostat shall be provided with actuators.

Dia 32mm

Dia 40mm

Dia 50mm

Dia 65mm

Dia 80mm

Y-Type Strainer complete with Cast Iron Valve body, Flanges, Bolts, Nuts, Gaskets, Filter, Mesh less than 20, 1.6 mm thick Screen, PN 16 rating. Valve shall be insulated as per specifications.

Dia 32mm

Dia 40mm

Dia 50mm

Dia 65mm

Dia 80mm

150 mm Dial type pressure gauges 0-10 bar range with Ball Valve

150 mm Dial type Temperature Gauge 0-50 Deg. range.

Purge Valves PN 10 rating

Drain with standard ball valves PN 10 rating.

Dia 40mm

Dia 32mm

UPVC pipes insulated with 9 mm thick superlon insulation

Dia 65 mm

Dia 50 mm

Dia 40 mm

Dia 32 mm

Dia 25 mm

Temperature cum RH control panel for operation theater AHU. The control panel shall consists of temperature & RH sensor and able to control inside temperature by modulating three-way valve for Block 3 & PIBCV valve for Block 1 & Block 2 and control RH by regulating heaters through Thyrisor drive.

Duct Thermal insulation with 19 mm thick closed cell Self Adhesive Nitrile rubber meeting Class 0 as per BS 476 Part 7. The insulation shall have factory laminated Al foil /eqvi.. The joints shall be covered with Self adhesive tape of same material (No brown tape).

Supply, Installation, Testing and Commissioning of Duct acoustic Insulation with 15 mm thick open cell Nitrile rubber - Armasound/ Equivalent.

Duct Thermal insulation with 13 mm thick closed cell Self adhesive Nitrile rubber meeting Class O as per BS 476 Part 7. The insulation shall have factory laminated Al foil /eqvi.. The joints shall be covered with Self adhesive tape of same material (No brown tape).

Double skin plenum made out of 25 mm thick PUF of dersity 38kg/cu.m. sandwiched in between 220 Aluminum Inner & outer skins complete with Aluminum extruded profiles and Nylon comers. Intemal size of the plenum shail be 2540 x 1980 x 660 mm (Height) with 25 x 25 x 3 mm Aluminum angles fixed inside to accommodate sufficient Nos of HEPA Sitters of size 610 x 610 x 152 mm,306 x 305 x 152 and UV GERMICIDAL LAMPS. The HEPA filters shall have an efficiency of 99.99% down to 0.3 micron and shall be of outer size 610 x 610 mm and 306 x 305 mm complote with Aluminum frames. The fiters shall be removable from the bottom/top and the face of the plenum shall be covered with 16G stainless steel perforated sheet having 3mm dia perforations and 70% of free area.

Duct Velocity sensor with 4-20mA/0-10VDC output, shall be able to adjust the speed of the VFD through PID loop funtion.

Supply, fitting and fixing of HEPA Sitters of size 610 x 610 x 152 mm,306 x 305 x 152 and UV GERMICIDAL LAMPS. The HEPA filters shall have an efficiency of 99.99% down to 0.3 micron and shall be of outer size 610 x 610 mm and 306 x 305 mm complote with Aluminum frames. The fiters shall be removable from the bottom/top and the face of the plenum shall be covered with 16G stainless steel perforated sheet having 3mm dia perforations and 70% of free area.

FAN FILTER UNIT

Supply, Installation, testing & commisioning of Fan unit units with micro-glass fiber filter media & H13/H14 fiter grade, with liltering efficiency of 99.99% down to 0.3 3 micron, media depth shall be 48 mm & M.O.C. shall be Aluminium., with TRIAC speed controllers. (a) Size: 1210 mm (L) x 610 mm (W) x 335 mm (H) (BMT ICU Supp

Direct Drive Fans

Ducted inline fan with direct connection two speed motors, thermal over load protection, suitable for single phase power supply and back draft shutter. Sound level shall be less than 55 dBA@1m distance. Exhaust Fans

1100 CFM & 15 mmwc Total Static Pressure

850 CFM & 15 mmwc Total Static Pressure

700 CFM & 15 mmwc Total Static Pressure

450 CFM & 15 mmwc Total Static Pressure

400 CFM & 10 mmwc Total Static Pressure

250 CFM & 10 mmwc Total Static Pressure

200 CFM & 10 mmwo Total Static Pressure

150 CFM & 10 mmwe Total Static Pressure

Supply, installation, testing and commissioning of forward/ backward curved Centrifugal DIDW fan complete with connection & as per the specification and shall be suitable for out door applications, necessary protection for the fans, Outlet dampens, Vibration isolators, Canvass connection & as per the specification and shall be suitable for out door applications. The outlet velocity should not exceed 10m/s and noise level shall not exceed 70dBA 1 m distance. Motor shall be Eff 1 type.

3500 CFM & 20 mmwc Total Static Pressure

2500 CFM & 20 mmwc Total Stafic Pressure

2000 CFM & 20 mmwc Total Static Pressure

1500 CFM & 15 mmwc Total Static Pressure

1200 CFM & 15 mmwo Total Static Pressure

Single skin venditation unit with backward curved/forward curved centrifugal DIDW fan, fan, Cleanable pre filter 90% effeciency down to 10 micron and outlet dampers with frerstanding Canvass connection. Outlet velocity shall be less than 9.5 m/s & Suitable for out door applications Sound levels vel shall be less than 71 dBA 1 m distance, Motor shalt be Eff 1 Type.

2100 CFM & 20 mmwe Total Static Press

Wall mounted Propeller type single phase Exhaust fan complete with motor, wall cowl with bird screen etc., as per Specification and drawings Sound level shall be less than 55 dBA 1 in distance.

Dia 150 mm, Pole 4, Speed 1300 Rpm

Dia 200 mm, Pole-4, Speed 1300 Rpm

Dia 255 mm, Pole 4, Speed 1300 Rpm

Dia 315 mm, Pole 4, Speed 1300 Rpm

Supply, installation, testing and commissioning of forward/ backward curved Centrifugal DIOW fan complete with connection & as per the specification and shall be suitable for out door applications, necessary protection for the fans, Outlet dampers, Vibration isolators, Canvass connection & as per the specification and shall be suitable for out door applications. The outlet velocity should not exceed 10m/s and noise level shall not exceed 70dBA @1 m distance Motor Shall be Eff 1 Type.

750 CFM & 25 mmwe Total Static Pressure

3050 CFM & 25 mmwc Total Static Pressure

2300 CFM & 15 mmwc Total Static Pressure

Factory fabricated Galvanized sheet metal duct work Including bends for supply air system complete with flanges, gaskets & supports elc., ducts to be fabricated/erected as per IS 277/15 665

Al powder coated diffusers/griles with MS Opposed blade Collar damper.

GI Manual Opposed blade Volume Control Dampers with 18G frame & 20G blades

GI, Fusible link, Fire dampers 375 mm long with sleeve as per UL 555 Standard.

Aluminium Door Louvers for Exhaust system

Al powder coated Exhaust air louvers with Collar dampers and Cowl & Bird Screen

Al powder coated fresh air louvers with Collar dampers and Bird Screen

Supply, installation, testing and commissioning of 2 x 2.5 KW strip type duct/plenum mounted air heaters for monsoon reheat complete with gyserstat for AHU. Heaters will be complete with humidstat for each step and control waring with 1.5 Sqmm copper conductor.

Tube axial fan complete with class 'F motor (TEFC, Sq.onge induction, 415 V, 50 Hz, IP 55 protection), outlet velocity shall be less than 14.0 m/s, the fan shall be suitable for floor mounting. Casing Mild steel. Sound level shail be less than 85 dBA @ 1m distance for LIFT WELL PRESSURIZATION. The fan Shall Suitable for Outdoor applications.

12000 CFM & 30 mm. Total static pressure

Supplying and laying of PVC insulated FRLS Multistranded CU Conductor Wire with 6 runs of 1.5Sqmm complete with all accessories wiring termination etc from thermostat to FCU Unit (Circuit Wiring)

Supplying and laying of PVC insulated FRLS Multistranded CU Conductor Wire with 2 runs of 1.5 Sqmm complete with all accessories wiring termination etc from thermostat to FCU Unit (Circuit Wiring)

Supplying and laying of following sizes electrical welded MS conduit to be concealed in slab/wall/surface mounted with necessary accessories like bend, couples etc. the rate shall include rough plastering metal junction boxes of suitable size at regular intervals.

20 mm dia 1.6 mm thick MS Conduit

25 mm dia 1.6 mm thick MS Conduit

Supplying and laying of following sizes of FRLS heavy duty PVC conduit to be concealed with slab/wall/surface mounted with necessary accessories like bend, couples, saddles at every 600mm etc. the rate shall include rough plastering metal junction boxes of suitable size at regular intervals.

20 mm dia 2 mm thick MS Conduit

25 mm dia 2 mm thick MS Conduit

MACKINTOSH BURN LIMITED (BID ID -162820)