PROVISION OF 2XTIOLET NEAR TECH REPAIR BAY , 01X TOILET A, 01X BATHROOM,02X URINALWITH WHB NEAR P-34 AND SPECIAL REPAIR TO BLDG NO T-23 BS YARD UNDER AGE-BR-I AT GE KH YOL

Amount

SCHEDULE 'A' PART-I Excavation in trenches not exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, all as specified.

Removing excavated material EXC 250m but not exc. 500m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified.

RCC M-20, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or wire staples or wooden beads, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall of bore 110mm complete, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall of bore 75mm complete, all as specified.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4(1 cement : 4 coarse sand), complete all as specified.

PVC (SWR) bends any radius, 110mm bore with ovel access door, all as specified.

PVC (SWR) vent cowl 110mm, complete all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on other than fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

75mm thick Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

25mm thick Plain cement concrete 1:2:4 nominal mix, using 12.5mm graded mechanically crushed stone aggregate over sub base complete all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Spreading and leveling in layers, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, all as specified.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan in one brick thick honey comb walling, built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Supply only intergal water proofing compound, complete all as specified.

Non skid, Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Glazed coloured tiles of size 350x250/450x300x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders, all as specified.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified,including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe , fixed complete , all as specified.

Vitreous China bowl Urinal, flat back 465x355x265mm ,white ( white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed , all as specified.

Salt-glazed stoneware gully traps, round mouthed, type 'P ', of size 150mmx 150mm, complete all as specified.

Angular Stop Cock with Wall Flange , cast copper alloy, fancy type chromium plated, screwed down ,high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed complete, all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed , complete all as specified.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed , complete all as specified.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. laid in trenches complete, all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Bib taps, fancy type CP 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed , all as specified

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm , fixed ,all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm , all as specified.

Butt hinges, medium weight, cold rolled, mild steel stainless 100 mm long, all as specified.

Factory made solid panel PVC ventilator or window shutter 30 mm thick (style) consiisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC C channel heaving a PVC sheet strip of 20 mm width such inside with solvent ement for stiles and plain colour PBC sheets for top rail, lock rail & bottom rail either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame wedded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing.

PVC (SWR) bends any radius, 75mm bore with ovel access door, all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 75mm bore, provided with oval access door all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 110mm, all as specified.

Rotational moulded polyethylene water storage tank 250 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with brass ball float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with brass ball float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Applying two coats of synthetic enamel paint over pre-primed steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Three coats of white wash on newly plastered or un plastered, previously undecorated wall surfaces including preparation of surfaces complete, all as specified.

Mild steel work as in bolt hooks (stay) hook and pintle hinges, bands, straps, hold fasts, clamps, wall ties, cleats, fanhooks etc. or similar small articles conforming to grade Fe-290 grade E-165, all as specified.

Joist channel, angle or tee section fixed independantly without connection plate etc . conforming to grade Fe.410-0.Gde-E-250, steel work ,all as specified.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe 410 -W(Gde-E- 250 quality-A ), complete, all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410-0.Gde-E-250, complete ,all as specified.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165 , all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for roughly finished flat surfaces of concrete, all as specified.

Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Excavation over areas not exc 1.5 metres deep and getting out in any type of soil, all as specified.

Excavation over areas exc 1.5m but not exc 3 metres deep and getting out in any type of soil, all as specified.

Plain cement concrete M-15, nominal mix, type B-2, using 40mm graded mechanically crushed stone aggregate as in floors, 100mm thick, all as specified.

Plain cement concrete M-15, nominal mix, type B-2, using 40mm graded mechanically crushed stone aggregate as in floors, 75mm thick, finished even and smooth without using extra cement all as specified.

Rendering cement plaster 20mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering cement plaster 20mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement.

Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For roughly finished flat surfaces of concrete, all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

Precast RCC M-15 nominal mix, type B-1, using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match, complete all as specified.

Loose filling with brick bat, aggregates of gauge 80-150mm in soakage pit or soakage well.all as specified.

75mm dia cast iron soil,waste and vent pipes, in any length with or without ears with cement joints, fixed to wall.

M&L for 150mm reinforced concrete pipe with collers, class NP2, drain pipes laid in tenches and joints as specified.

M&L PCC 1:4:8 type D2 for concrete bed to 150mm drain pipes Note:- The unit rate include for use of form work (straight or curved).

Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof . all as specified.

Dismantling wrought iron or mild steel work of any description. all as specified.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete,all as specified.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty complete, all as specified.

Preparation of newly plastered wall surfaces and appling two coats of cement base paint over a coat of white wash complete, all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced, complete all as specified.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified.

Machine cut kota stone,18-20 mm thick , as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in vertical surfaces such as skirting/dado/riser to step/pillar aid over and including 10mm thick bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, , all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Pressed steel frames of size 105x60mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 60mm x 25mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick required no of each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) MS work with angle or other section as in window gurad bars, grill (ix) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. if iron scrap retrived under this item shall be sold to contractor under Sch of credit.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Factory made 35mm thick second class hard wood (Sal) rail and style Plain framed, panelled shutter without interlocking rail and with one panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treatedcomplete all as specified.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduits, medium grade, ISI marked not less than 20 mm dia and conforming to IS-9537 (Part-II) 1983 with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire connected to common earth dolly and including pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '97' above, but for one 3 pin 5 Amps socket outlet on the independent board, all as specified and directed.

All as per Srl item No. '97' hereinbefore but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5/6 Amps, all as specified.

Switch socket combination outlet Two -in -One 3 pin 5 amps flush type, 230 volts AC multipurpose all as specified.

Switch socket combination outlet Two -in -One 3 pin 15 amps flush type, 230 volts AC multipurpose all as specified.

MCB SP 6 to 40 Amp, 240 Volts, 10 KA all as specified.

MCB SPN 6 to 40 Amp, 240 Volts, 10 KA all as specified.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 10 Sqmm 2 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying complete all as specified.

Ceiling rose, surface bakelite 65x50mm, three terminals all as specified and directed.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral (double Door), 4 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2009 Part-I and directed by Engr-in-Charge.

Sub class 'B' bricks old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.

Mild steel galvanised light grade 40mm dia tubing with all fitting; laid in trenches, across road or on pole complete all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, all as specified.

LED tube light fitting integral type 1x20W, 230V, connector block etc complete with all accessories internally repwired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Makes mentioned in Appendix 'C'.

LED tube light fitting integral type 1x10W, 230V, connector block etc complete with all accessories internally repwired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. makes mentioned in Appendix 'C'.

Endura Pearl 25 W new generation energy saving and environmental friendly long life LED Bldg security light made up of pressure die case aluminium housing with high power LED as lighting source an lens enbedded PC cover having TOP opening seperate toughted glass/verminproof driver compartment, SPDs with IP66 protenction and impact rresistancee of IK07 connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, Makes mentioned in Appendix 'C'.

35Watt energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source nd lens enbeddedPC cover having IP65 protection and impact resistance of IK07, suitable for pole dia 43mm(max) connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket complete all as specified and as directed. Makes mentioned in Appendix 'C'.

Energyy efficient Exhaust fan, 250mm sweep,1400RPM with louvers shutter and connecting up including provision of three core flexible copper wire of size 1.5 mm Sqmm from connector to ceiling fan complete in all respect all as specified and directed.

surinder kumar jindal & bros.