SPECIAL REPAIR TO CERTAIN BLDGS IN ARMY AREA JODHPUR UNDER GE SHIKARGARH

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc; overall thickness and removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all as specified and as directed by Engineer in charge.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. Note : (WPC shell be measured separately and paid for under respective item of schedule). (ii) First coat of bitumen primer confirming to IS 3384 @0.300 Kg/ Sqm over plastered surafces (iii) Second layer of 3.0 mm thick APP modified polymeric membrane with centre core of Single non woven polyster reinforcement and having weight 3.6 Kg/ Sqm with mineral gravel finish on top complete laid with blown type bitumen grade 85/25 @ 1.20 Kg/ Sqm complete all as specified and as directed. (iv) Finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against UV, including preparing of surfaces of roof (second coat apply after 24 hrs or as per manufacturing instructions).

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates filling over roof for making good depression/ undulation of existing roof surfaces roof slab/ floor padding/ roof kerbs rounded or chamfered on edges coping etc; complete all as specified and as directed.

Dismantling stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified.

M&L Jodhpur stone roof slabs, self faced exceeding 10cm but not exceeding 12.5 cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3, complete all as specified and as directed.

-ditto- all as per above item but, except stone complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-1,using 20mm graded stone aggregates as in coping to parapet walls including necessary formwork complete all as specified and as directed.

Supply only integral water proofing liquid ISI marked Make: Pidiproof LW or equivalent

Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site all as specified and as directed.

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide.

M&L for virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for virified ceramic tiles 10 mm thick (square/ rectangular) polished, as in skirting (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.

M&L for 16-18mm thick green marble work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for 16 -18mm thick granite (BLACK colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for Jodhpur stone slabs, machine cut (dressed face) 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted (vertical or horrizontal) and set, jointed and grouted cement mortar 1:3 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab making with cutting of groove as required etc; complete all as specified and as directed.

M&L for Jodhpur stone slab patti machine cut, 40 to 50mm thick set in over and including 15mm thick cm 1:4 and jointed & pointed in neat cement slurry as in floors, plinth protection, including provision of construction joints as required etc; complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified.

M&L for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg/Sqcm, of shape and colour as approved by GE , laid over 25mm thick compacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed.

M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified.

Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

-ditto- all as per above item but, except stone complete all as specified and as directed.

M&L for brick work with fly ash bricks (old size bricks), straight or curved on plan exc 6mtr mean radius, built in cement mortar (1:6) complete all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

M&L for Pre-cast cement concrete block type C1, 1:3:6 (20mm graded aggregate) as in masonry with solid blocks, exc. 10 cm in width and setting in cement Mortar 1:6 complete all as specified and as directed.

-ditto- all as per above item No 28 but, except concrete block complete all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed

M&L for rendering 15 mm thick in CM 1:6 over stone masonary, concrete surfaces, finished even and smooth (without using extra cement), all as specified and as directed.

M&L for 15 mm thick rendering on stone masonary wall surfaces in CM 1:4 finished fair and even all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for carrying out water proofing treatment for sunken portion in the following stages - (i) Taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish of the pemises , cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00kg/sqm and grouting 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (ii) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXITpidifin 2k manufactured by M/s Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (10mm thick cement mortar (1:4) along with liquid water proofing compound approved make as per manufacturer's instructions) on top surfaces of sunken slab after preprations as mentioned above. Method of application for acrylic cementitious water proofing coating achieved as per manufacturers instruction complete all as specified and directed.

Dismantling cast iron work of any description and in any position complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

Fixing only in repair 100mm bore any type of soil, waste and vent pipes in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

Fixing only in repair 100mm bore any type of soil, waste and vent pipes in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

Fixing only in repair 75mm bore any type of soil, waste and vent pipes in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

Fixing only in repair 75mm bore any type of soil, waste and vent pipes in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 100mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 75mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 100mm bore pipe cast iron cowls, complete all as specified.

Fixing only in repair 100mm bore pipe cast iron or any type cowls, complete all as specified.

S&F 75mm bore pipe cast iron cowls, complete all as specified.

Fixing only in repair 75mm bore pipe cast iron or any type cowls, complete all as specified.

M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

Fixing only in repair any type or cast iron up 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

S&F for 75mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

M&L cement concrete type E-2, 1:5:10 (40mm graded crushed stone aggregate) as in sunken portion complete all as specified.

S&F 40mm bore steel water tubing medium grade galvanised inserted at the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specifide.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.00 sqm each and removing from site or to store as directed by Engineer incharge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site or to store as directed by Engineer incharge.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and removing from site or to store as directed by Engineer incharge.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the shutter in same opening after easing and adjusting complete as directed by Engineer incharge.

M&L for fabrication of aluminium powder coated window/ vents any pattern & design (openable with hinges, sliding, tilt and turn, casement , fixed type, villa type, ventilators) fabricated with anodized aluminium rectangular or any type section in frame with approved design & patterns including provn of fixing galvanised mild steel wire cloth on the outer side of frame etc; fixed in position all as specified and directed. Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately under respective Items of Sch 'A'.

Pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

Pressed steel framed made out of 1.25mm thick MS sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc., complete all as specified

Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified

M&L 40mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both side complete all as specified.

Factory made 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified.

S&F of Factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8/10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (with provision of fixing for cooler if required) all as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 fixed in repairs i.e, incl taking down and removal of old steel windows from site or to store complete all as specified and directed. Note:- (i) Guard bar/ grill shall be measured and paid separately under respective item of Sch 'A'. (ii) Drg No. mentioned is for reference only and may be seen any of the office during working hours.

M&L for fabrication of aluminium powder coated window/ vents any pattern & design (openable with hinges, sliding, tilt and turn, casement , fixed type, villa type, ventilators) fabricated with anodized aluminium rectangular or any type section in frame with approved design & patterns including provn of fixing galvanised mild steel wire cloth on the outer side of frame etc; fixed in position all as specified and directed. Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately under respective Items of Sch 'A'.

S&F Sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed.

.-Ditto- all as per above item No 73 but 4mm thick frosted glass complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.

Mild steel round bars welded to steel windows or ventilators as in guard bars framed or unframed complete all as specified & as directed by Engineer incharge. Note: - Guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. Cost of factory welding & Shop coat of primer is deemed to be included in quoted rates.

Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing S&F. Make : Rajshree Doors or equivalent as approved by GE.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. Make : Rajshree Doors or equivalent as approved by GE.

S & F 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed.

S&F mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified.

Mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified.

300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified.

S&F Mild steel rat tail rod pattern helical door spring of size 300mm including roller and roller plate fixing to iron frame by welding complete all as specified & as directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise specifically provided for (framed/ unframed work) complete all as specified.

S&F framed work as in doors chowkats of MS angle iron or MS hollow square/ rectangular any type/ size with gusset plates, rails, braces,cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to FE- 290 (Gde-E- 165) complete all as specified and directed by Engineer-in-charge.

Demolition of RCC work as in Roofs, floors (other than ground floors), beams, stair cases, landing, chajjas and similar suspended work incl (reinforcement cut as required to facilitate demolition)

M&L for reinf cement concrete 1:2:4 type B1 using 20 mm graded stone agg as in copings, kneelers, apex stones, bed plates, kerbs lintels upto 1.5m clear span, cills, steps; seismic and other similar bands including necessary formwork, not provided including weathering, slightly rounded or chamfered angles and throating,

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, includingcranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia

M&L for Mild steel TMT bars 6 mm to 8mm dia over bent to shape required, including cranking, bending & binding as in stirrups / rings

M&L for providing steel scafolding & formwork etc for supporting RCC Slabs etc for carrying out the rehabilitation works complete all as specified & directed . Note:- The steel scaffolding & formwork etc catered for in the items above is for supporting the RCC members during the period of their structural rehabilitation. The scaffolding & formwork shall not be removed until the RCC members have gained sufficient strength. The decision of GE shall be final conslusive & binding in respect of the extent to which the formwork is to be provided & time of its removal.

M&L for providing steel scafolding & formwork etc for supporting RCC Beams etc for carrying out the rehabilitation works complete all as specified & directed . Note:- The steel scaffolding & formwork etc catered for in the items above is for supporting the RCC members during the period of their structural rehabilitation. The scaffolding & formwork shall not be removed until the RCC members have gained sufficient strength. The decision of GE shall be final conslusive & binding in respect of the extent to which the formwork is to be provided & time of its removal.

M&L Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete

Prelaminated particle board 18/ 19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with wooden beading as required fixed in repairs i.e., including taking down and removal of old unserviceable boarding of any description and in any position complete all as specified and as directed.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F hydraulic hings for cabin door shutter of mild steel bright finish or elecrogalvanised, fixede with screw etc; complete all as specified.

S&F Mild steel butt hinges 100mm long, medium weight cold rolled fixed with steel chowakats etc; complete all as specified.

S&F Mild steel single action helical hinges 150-200mm long, suitable for 1000-1250mm wide wooden door fixed with steel chowakats etc; complete all as specified.

S&F ball catches with 8mm dia steel ball and brass body and stiking plate incluing letting and fixed in repairs.

S&F ball bearing single extension drawer slide (runner) 300-450mm clear slide and 25-30mm wide,fixed with screws etc complete all as specified.

S&F alluminium anodised handles 100 mm long fixed to windows all as specified and directed.

S&F 50mm dia polished hard wood knobs fixed with screw complete fixed in repairs.

Decorative mild steel curtain rods 32mm dia (powder/ PVC coated) including fixing brackets & side cups complete fixed in repairs i.e., including taking down the existing unserviceable curtain rods complete all as specified and directed

S&F Powder coated aluminium anodised deco grill weighing not less than 1.40 kg/ sqm and fixing necessary joining cleats/ frame etc; complete all as specified.

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Supply, fixing, Jointing and testing 15 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

Supply, fixing, Jointing and testing 20 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

Supply, fixing, Jointing and testing 25 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

Fixing only 15mm bore steel water tubing any grade with all new fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Fixing only 20mm bore steel water tubing any grade with all new fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Fixing only 25mm bore steel water tubing any grade with all new fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Vitreous China wash down water closet pan (Pedestal Pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube (Make of Jet 'Praayag' Cat Part No 5211 or Equivalent) incl making connection to inlet flush pipe, & to 'P' or 'S' drain trap, incl supply of long special 'P' or 'S' trap fixed in repair complete and making good the disturbed portion etc. all as specified and directed.

Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified.

S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. all as specified.

S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified.

S&F in repair for Vitreous china urinal, half stall type, white,complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement , suitable PVC waste pipe with brass unions, including making all connections to existing connections,complete all as specified and as directed.

Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified.

Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting refixing in position complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer in white colour hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified.

S&F in repair 15mm bore chromium plated Bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repair for Pillar tap, brass, 15mm dia, with capston heads, chromium plated, fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed.

S&F in repair 15mm bore stop valve/ angle stop cock chromium plated, fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified.

S&F in repair Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc; complete all as specified.

S&F in repair CP towel rail 450mm long fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified.

S&F in repair CP greating doom 100mm dia complete all as specified.

Supply and fixing 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed.

S&F in repair PVC SWR type 'B' socketed rain water pipes 110mm dia conforming to IS: 4985/ IS: 13592 complete all as specified and as directed.

S&F in repair PVC SWR bend/shoe of PVC 110mm dia suitable for 110 mm bore / dia PVC SWR rain water pipes complete all as specified and as directed.

Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer incharge.

Preparing new plastered surfaces and M&L for applying chalk whitening/ concrete primer incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion on new plastered surfaces all as directed by Engr in charge.

Preparing new plastered surfaces and M&L for applying concrete primer incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of cement base paint on new plastered surfaces all as directed by Engr in charge.

Preparation of new plastered surfaces of walls etc. & applying three coats of lime white wash on walls complete all as specified.

Preparation of new plastered surfaces of ceiling etc. & applying three coats of lime white wash on ceiling complete all as specified.

Preparing old plastered surfaces brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of distempered or painted surfaces and M&L for applying one coat of distemper oil emulsion on old plastered surfaces all as directed by Engr in charge.

Preparing old surfaces incl brooming surfaces, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil or greasy spots incl washing rubbing down and stopping of distempered and painted surfaces and M&L for applying one coat of cement base paint on walls etc., complete all as specified and as directed.

Preparation of old decorated plastered surfaces of walls etc. & applying one coat of white wash complete all as specified.

Preparation of old decorated plastered surfaces of ceiling etc. & applying one coat of white wash on ceiling complete all as specified.

Taking down carefully aluminum/copper point wiring (light/fan/ socket/ power) complete including fittings such as switch, socket, ceiling roses light fittings etc and and making good disturbed surface of wall all as specified and directed by Engineer-in-Charge.

Material and labour for point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC FRLS insulated unsheathed 1100 Volt grade cable in and incl PVC FRLS CONCEALED CONDUIT PIPE (ISI Marked) with all accessories including new pressed steel terminal boxes (sunk in wall ) with 3.00 mm thick plastic laminated sheet top cover or PVC FRLS board including PVC FRLS top cover with 1.50 sq mm insulated unsheathed PVC FRLS multistranded covered copper conductor for common earth and connecting to earth dolly and making good disturbed surface of wall incl matching the colour of wall/ceiling with extisting wall/ceiling colour all as specified and directed for One light /security light / Exhausat / Fan point controlled by one switch one way

---Ditto--- as per item No 143 above but for one socket out let 5 Amps 5 Pin on same board with other switch

---Ditto--- as per item No 143 above but for one socket out let 5 Amps 5 pin on independent board

All as per item No 143 here in before but with single core multistranded cable of size 4.0 Sqmm for one 15 Amps socket outlet on independent board and multistanded insulated copper earth continuity conductor of size 4.0 Sq mm all as specified and directed

Material and labour for Modular point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC FRLS insulated unsheathed 1100 Volt grade cable in and incl PVC FRLS CONCEALED CONDUIT PIPE (ISI Marked) with all accessories including new pressed steel terminal boxes (sunk in wall ) with 3.00 mm thick with top cover for modular fitting with 1.50 sq mm insulated unsheathed PVC FRLS multistranded copper conductor for common earth and connecting to earth dolly and making good disturbed surface of wall incl matching the colour of wall/ceiling with extisting wall/ceiling colour all as specified and directed for One light/Fan/Call bell point controlled by one switch one way

---ditto---as per item No 147 above but for one socket out let 5 Amps 5 Pin on same board with other switch

---ditto--- as per item No 147 above but for one socket out let 5 Amps 5 pin on independent board

---ditto--- as per item No 147 above but for one light point controlled by two switch two way

All as per item No 147 here in before but with single core multistranded cable of size 4.0 Sqmm for one 15 Amps socket outlet on independent board and multistanded insulated copper earth continuity conductor of size 4.0 Sq mm all as specified and directed

Supply and fixing switch Modular type 6 Amps two way.

Material and labour for bell push Modular type 6 Amps .

Supply and fixing switch Modular type 6 Amps single pole one way.

Supply and fixing Modular socket out let 2 in 1 multi pin 5/6 Amps 2 module.

Supply and fixing switch Modular15/16 Amps one way 240 volts

Supply and fixing Modular socket outlet in repair 2 in 1, 3 pin, 5 and 15 Amps socket outlet 240 volts SP

Supply and fixing Modular electronic fan regulator 2 module

Supply and fixing Ceiling rose on PVC FRLS board size 65 X 50 mm three terminal Complete.

Material and labour for Elect bell AC 230 Volts single phase musical type.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single MCB SP 20 Amps.

Supply and fixing Lamp Holder, PVC FRLS/polycarbonate type with back plate suitable for batten fittings.

Decorative wall light fixture made up of Polycarbonate, of capacity 12W (B-22 base)

Supply and fixing concealed sub main wiring with 2X10 Sqmm single core copper conductor (Multistandered) in concealed PVC FRLS conduit of suitable size as required, including single core 6.0 Sqmm copper conductor as earth continuity all as directed. NOTE: Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit.

Supply and fixing switch piano flush type 5 Amps single pole one way.

Supply and fixing socket out let 2 in 1 multi pin 5 Amps flush type universal.

Supply and fixing switch piano15/16 Amps one way 240 volts

Supply and fixing socket outlet in repair 2 in 1, 3 pin, 5 and 15 Amps socket outlet 240 volts SP

Supply and fixing box type powder coated luminaire LED 1X10 watt LED tube light with all accessories and necessary connection.

Supply and fixing LED batten 20 Watt inbuilt rod and driver complete with all accessories and necessary connections.

Supply and fixing Pressure die-cast IP 66 LED streetlight 60 Watt with all accessories, necessary connection incl GI pipe of suitable size of bore dia, clamps, nuts and bolts.

Supply and fixing double door manufacturer MCB DB SPN 12 way flush in wall comprising of sheet metal enclosure powder coated fitted with bus bar 200 Amps 240 volts.

S7F Vertical DB double door suitable for A frame FP MCCB 160 A made out of CRCA mild steel sheeet surface with insulated material like polyster or with epoxy coating VTPN 4 way 415 v with bus bar rating 400 A dust and vermin proof suitable for incorporation of MCBs and MCCB etc and making all necessary connection concealed flush to wall surface complete all as specified and directed.

S&F MCCB A Frame thermal adjustable magnetic setting Ics = 75% 25 KA 415V 160 Amp 4 Pole MCCB with over load and short circuit protection complete all as directed

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanised earth lead wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 25 mm bore including provision of concrete pit made from PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2009 Part-I and connecting to Poles all as specified or indicated including testing on complete all as specified and as directed by Engineer-in-Charge.

M&L for Taking down elctric energy and keep in safe custody for refix after complete of work by making all necessary connection.

M&L for Disconnecting all water/electric connection and taking down water heater geyser from existing position and keep in safe custody for refix after completion of work by making all necessary connection.

M&L for Taking down exhaust fan from existing position and keep in safe custody for refix after complete of work by making all necessary connection.

M&L for Taking down ceiling fan from existing position and keep in safe custody for refix after complete of work by making all necessary connection.

Supply and fixing in repair 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissionin

Supply and fixing MCB SPN, 40/63 Amp, C Curve 240 volts.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 16 sq mm 2 core

`-ditto- as per item no 182 but for size 50 sqmm 3 core

M & L for GI pipe light grade of 50 mm bore with necessary fittings laying in treanches, floors, fixed to wall/poles all as reqd at site and all as directed by the Engineer-in-charge.

Excavation in trenches not exceeding 1.5 m wide and not exeeding 1.5 m in depth and getting out in soft/loose soil for removing/laying of cable etc as directed by Engineer-In-Charge.

Returning, filling excavated soil in trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each all as directed by Engineer-In-Charge.

Removing surplus excavated soil to a distance not exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point.

M&L filling in trenches with fine sand cushioning for LT UG cable including compacting after filling complete all as specified and directed. Note : sand to be filled 23cm and carefully punned to 18 cm thickness. Punned thickness will be measured for the purpose of payment

Supply and laying un-reinforced precast concrete cable covers, factory made, class-LV, Type-1, flat, as per IS 5820, of size 300mmx 180mmx40mm laid dry complete all as specified and as directed. Make : Hind Upleta / Mehtab/ Hind Mosaic/Lucky Concrete Skg/Jodh

Bhagwati Construction Company

M/S HARIOM CONSTRUCTION COMPANY

M/S Dharam Chand Lal Chand Jain