Renovation of Work Shop building at WRPL, Viramgam

Amount

Security Door (Work Shop and Work Floor seperator)

Supplying, fitting & fixing in position fully glazed anodised aluminium doors of AJIT INDIA or equivalent make using aluminium extruded sections of INDAL glazed with 5.5 mm thick plain glass pans special gasket felt and aluminium, beading hydraulic floor mounted double action door closer, rubber lining for air tightness etc. and all fixtures and fastening complete as per approved Manufacturer's specifications. As per Arch. Std. Openable/ Fixed.

Providing and fixing Latch lock of "Godrej" with handles,key & necessary screws etc. complete (6 levers).

Office room for New FF ARC

Supplying, fitting & fixing in position fully glazed anodised aluminium doors of AJIT INDIA or equivalent make using aluminium extruded sections of INDAL glazed with 5.5 mm thick plain glass pans special gasket felt and aluminium, beading hydraulic floor mounted double action door closer, rubber lining for air tightness etc. and all fixtures and fastening complete as per approved Manufacturer's specifications. As per Arch. Std. Openable/ Fixed.

Providing and fixing Latch lock of "Godrej" with handles,key & necessary screws etc. complete (6 levers).

Providing 6mm thick plain faced in cement plaster in CM 1:3 (1 cement : 3 fine sand) on underside of ceiling and other concrete surfaces including scaffolding, finishing smooth, curing all complete as per specifications and directions of the Engineer-in-Charge.

Designing, providing, fabricating and fixing profiled sheeting 06337 730-1020mm cover width, 28-30mm crests @ 186-333mm c/c manufactured out of 0.45mm BMT (Base Metal Thickness) Hi-Tensile steel (minimum yield strength of 550 Mpa) coated with hot dip metalic galvalume/zincalume coating AZ 150 or equivalent as per AS 1397 and super polyster XRW quality paint coat as per AS/NZS2728 (category-3) of approved colour for roofing, cladding, gutters, rain water pipes, spouts etc. The total mass of the coating on both sides shall be 150 gms/sqm (zinc (45%)/ alum (55%). The total paint coat thickness shall be 35 microns, comprising of 20 microns exterior coat of super polyster XRW on top surface and 5 micron super polyester on back surface over 5 micron primer coats on both surfaces including side and end laps. The sheets shall have wide pans with 2-3 stiffening ribs for effective water shedding and special male/female ends with full return legs on side laps for purlins support and anti-capilary flute in side lap. The sheets shall be fixed using polymer coated hot dip galvanised hex head self drilling asteners as per AS:3566 class 3 on each crest of sheets for connection with purlins and polymer coated hot dipped stitching fasteners at 300mm c/c on all sides and end laps etc. Approved sealing tapes shall be used on side laps and end laps of sheets and closer to be provided at the last end of sheet. The measurement shall be based on per unit of finished/laid area. Item to include curved sheets also wherever required. The contractor shall give minimum 10 year guarantee for the sheets against deterioration, disintegration, loss of lustre, variation in colour etc and leakages across laps, fasteners etc. The contractor is to submit design and shop drawing for approval on the sheet profile, design and details before installation." The area of sheet coverings shall be measured on the flat surface i.e. without allowance for laps and ribs.

Dress changing partition for Technicians

Supplying, fitting & fixing in position fully glazed anodised aluminium doors of AJIT INDIA or equivalent make using aluminium extruded sections of INDAL glazed with 5.5 mm thick plain glass pans special gasket felt and aluminium, beading hydraulic floor mounted double action door closer, rubber lining for air tightness etc. and all fixtures and fastening complete as per approved Manufacturer's specifications. As per Arch. Std. Openable/ Fixed.

Providing and fixing Latch lock of "Godrej" with handles,key & necessary screws etc. complete (6 levers).

Electrical works

High Bay LED Lighting Fixture (Suspended Type) and fitting (Outdoor Type, As per technical specification Annexure-I)

Industrial LED Flood Light/ High Mast Fixture, fitting and all accessories such as ballast, capacitor etc. (Outdoor Type, As per technical specification Annexure-I)

Ceiling fan with electronic regulator & other accessories and fittingsetc. of with the following sweepsize:- 56" Sweep

Point wiring Supplying, installation and testing with 1.5 Sq.mm stranded PVCinsulated copper conductor wires for phase & neutral of 650V gradeincluding earthing by providing 1.5 Sq.mm earth insulated continutitywire of copper in PVC conduit (Supply & installation of PVC conduitcovered elsewhere in SOR) recessed on wall/ceiling/ false celingincluding supply & installation of switch boxes,junction boxes, pullboxes, bushes, screws, check nuts, bends, modular switches and sockets .The circuit wiring with 4 Sq.mm PVC copper wire from D.B. toswitchboard as required is also in the scope of the contractor.

1 light point controlled by 1 switch

Fan Point : Wiring with PVC insulated 2.5 sqmm copperconductor wire for fan points (1 fan point controlled by 1 modularswitch) including providing space for electronic regulator in switch box, providing and fixing fan hook in the ceiling as per specifications anddrawings.

Power point (16/6Amps) : Wiring for 250 V single phase andneutral 16 amps modular power plug point with PVC insulated 4 sq.mm.copper conductor wires for phase &neutral, 650 V grade includingearthing, the third pin with 2.5 sq. mm copper conductor earthinginsulated continuity wire, complete with providing and fixing of 6 pin16/6A modular socket and 20/10 A modular switch (1 plug point percircuit) as per specifications and drawings

Power point (6 Amps) : Wiring as in item no. 1 for 250 Vsingle phase and neutral 6 amps Y modular plug point with PVC insulated2.5 sq. mm. copper conductor wires for phase & neutral, 650 V gradeincluding earthing, the third pin with 1.5 sq. mm copper conductorearthing insulated continuity wire, complete with providing and fixingof 5 pin 6A modular socket and 10 A modular switch (1 plug point percircuit) as per specifications and drawings.

Lighting Distribution Board / AC Distribution BoardSupply , installation, testing and commissioning of TPN lighting / ACDistribution board of approved make as per appendix -1, with rating andfeeders as per specification. The DB shall be of IP-42 protection classand shall conform to IS 8623. The board shall be fitted with an acrylicdoor as per specifications and drawings

Type III Distribution Board : Double Door EURODB of Havells orequivalent approved make having bus bar 200 A TPN, 1 Incomer 125 A FPMCB Isolator with 125 A FP RCCB (Senstivity 100 mA) alongwith 3 numbers63 A TPN MCB as per specification

Painting

Surface preparation, supplying and painting two or more coats of weather proof acrylic smooth exterior emulsion paint of make ASIAN (APEX), BERGER or NEROLAC or equivalent on exterior walls over one coat of cement primer and wall putty where required as per specifications and of approved color and make including all scraping , removing unwanted material and scaffolding all complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work/concreate including smoothening the surface by sand papering etc complete with all labour and materials

M/S CHANDAN KUMAR

Uday Construction