REPAIR TO FENCING BOUNDARY WALL INTERLOCKING/CHEQUERED TILE AT ADM AND DEPOT AREA BADDOWAL UNDER GE LUDHIANA

Amount

Dismantling posts or struts (wood, steel or R.C.C.) any section embedded in Concrete, brick work, masonry, etc, including taking out embedded portion and making good disturbed ground all as specified and directed.

Dismantling barbed wire,fencing wire mesh, any type complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in soft and loose soil and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40 mm thick stone aggregate) as in foundation filling and mass concrete of fencing posts & struts.

S&F for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

S&F for galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips/welding complete all as specified and directed.

S&F for mild steel screw bolts (machine made) with dia of neck between 11mm to 15mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.

S&F for 4mm dia galvanised steel wire, 75x75 mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling, complete all as specified and directed.

M&L for two coat of synthetic enamel paint on new steel surface of any description over 10 cm in width or girth over red oxide primer incl preparation of new surfaces etc complete all as specified.

M&L for one coat of black bituminous paint on new steel surface of any description over 10 cm in width or girth incl preparation of new surfaces etc complete all as specified.

Taking down cement or cement lime plaster including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and fair without using extra cement complete all as specified & directed.

M&L for preparation of new plastered surface of wall and applyng two coats of cement base paint in camouflage pattern complete all as specified and directed .

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level). complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4Type B-1 using 20mm graded stone aggregate as in sub base finished even and fair without using extra cement including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete coloured interlocking paver block with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade laid over including 40mm thick sand layer and necessary cutting and waste as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for providing, cement concrete, (Type B0, 1:2:4, 12.50 mm graded aggregate) along with interlocking/chequered tiles, rounded or chamfered on edges as directed complete all as specified and directed by Engineer-in-Charge.

M&L for coloured chequered cement concrete tiles 30cm x30cm x 25 mm thick, set, jointed and pointed in neat cement slury with grey cement and pigment in floors and including 15 mm thick screed bed in CM (1:6) all as specified & directed by Engineer-in-charge.

CHOUDHARY ENTERPRISES

ANUJ ABROL CONTRACTOR

Kular and Company

B.L. Chaudhri and Co.

M/s R.N Construction Co.