Providing Galvalume sheet roofing and toilet facility for crop physiology laboratory at RARS Anakapalle

Providing Galvalume sheet roofing and toilet facility for Crop Physiology Laboratory at RARS, Anakapalle.

Dismantling, clearing away and carefully stacking useful materials for re-use and disposal of unserviceable materials with 100m lead as directed by the Executive Engineer duly taking actual pre-measurements before dismantling including all labour charges etc., complete Asbestos Cement Roof Sheet

Dismantling, clearing away and carefully stacking useful materials for re-use and disposal of unserviceable materials with 100m lead as directed by the Executive Engineer duly taking actual pre-measurements before dismantling including all labour charges etc., complete Wrought and framed timber in roofs or floors

Painting two coats with synthetic enamel paint Grade-II VOC (Volatile Organic Compound) content less than 50 grams/litre over primer coat of wood primer of approved brand to old wood work including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., and complete for finished item of work in all floors.

Providing M.S Sections for purlins 50mm M.S hollow Square pipes with necessary materials and cost and conveyance of all materials and labour charges etc for fabrication and fixing as per design including labour and machinery charges., complete as directed by the department

Painting two coats with synthetic enamel paint Grade-II VOC (Volatile Organic Compound) content less than 50 grams/litre over primer coat of red oxide to new iron work including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., and complete for finished item of work in all floors.

Supplying and fixing of Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.50mm thickness, Coating: Alu-Zinc coating AZ150 GSM. Tensile Strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting Thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours fixed with Self driven screws 14 mm dia with neoprene washers & including a coat of approved steel primer and two coats of approved paint on over lapping of sheets complete (up to a pitch of 600) etc., complete excluding the cost of purlins, rafters, trusses including cost and conveyance of all materials, labour charges complete for finished item of work in all floors.

Fly ash Cement Block Masonry work in CM(1:6) prop (Cement: Screened sand) in superstructure with fly ash cement/lime solid blocks of size 290mm x 200mm x 140mm from approved source having minimum crushing strength of 50 Kg/Sqem. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504).

Plastering 12 mm thick in single coat in CM (1:5) including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting Grooves as directed by Engineer in charge etc., complete for Internal & Even faces of Brick Wall and RCC exposed faces for finished item of work.

Roof Slab 100mm thick: VRCC M- 20 Nominal mix ( 1:1.5:3) (Cement:fine aggregate: coarse aggregate) (using 400kgs of cement) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including Adjustable Jack screw Props and Acro span Hire Charges For Centering & Scaffolding including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, and excluding seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete including Hire Charges For Centering & Scaffolding but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)

Providing Thermo Mechanically Treated (TMT) (Fe 500 grade as per IS 1786-2008) of different diameters for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc.,and overheads & contractors profit complete for finished item of work. (APSS No.126)

Providing Kadapa slab 40mm thick and not less than 0.457 M x 0.457 M and fixing with CM 1:3 including all incidental, operational, labour charges etc., complete for finished item of work.

Supply & application White washing three coats with white cement paint of approved quality to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, but excluding conveyance charges of materials for:-White wash - White washing 3 coats with white cement

Supply & Fixing of Stainless sink 36"x18" (914.4 x 457.2 mm) 1 mm thick with accessories and all labour charges etc., complete for finished item of work.

Supplying, installing and commissioning approved make European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of Hindustan / Neycer or Parryware make white glazed with 'S' trap,supplying and fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996 and 10 litres capacity single flush PVC low level cistern Parryware or equivalent with internal components and CP short bend and fixed using required size of nails and screws, 12.7mm PVC connections with brass union nuts CP coated and 12.70mm dia. NP bib tap 400 grams Seiko or equivalent complete including cost and conveyance of all materials to site, for finished item of work for all floors.

Supply and fixing of Bibcock cum Health Faucet with 1 m long flexible tube and wall hook with 7 years warranty Chrome plated including cost and conyeyance of all materials to site, labour charges, etc., complete for finished item of work.

Supplying and fixing Indian make Flat Back Wash Hand Basin (HSW/Parryware/ Neycer) 1st quality conforming to IS:2556-Part-4:1972 of size 550mm x 400mm with 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/Senior/Nice/ Esso or equivalent complete with standard CI brackets including wooden blocks ,1 No.12.70mm PVC connection with brass union nuts CP coated , 1 No.12.70mm NP bib tap 400 gms Seiko or equivalent , 31.75mm dia. PVC flexible waste pipe 914.4mm length of 1st quality including cost and conveyance of all materials to site, labour charges etc. complete for finished item of work.

Supply and Fixing of 4"(101.6mm) multi floor trap with Jali - UPVC/SWR pipe fittings as per site requirements with standard practice for a floors including cost and conveyance of all materials to site, labour charges, overheads & contractors profit etc., complete for finished item of work.

28.60 mm OD Pipe: Supplying and fixing of Ashirvad / Ajay / Astral Flow Guard or equivalent CPVC pipes and fittings SDR 11 to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper tube sizes ½" to 2") for hot and cold water (IS 15778: 2007) including cost and conveyance of all materials to site, labour charges for fixing etc., complete for finished item of work at all floor levels.

22.20 mm OD Pipe: Supplying and fixing of Ashirvad / Ajay / Astral Flow Guard or equivalent CPVC pipes and fittings SDR 11 to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper tube sizes ½" to 2") for hot and cold water (IS 15778: 2007) including cost and conveyance of all materials to site, labour charges for fixing etc., complete for finished item of work at all floor levels.

75 mm dia pipe: Supplying and fixing of SWR/PVC pipes (as per ISI standards) 4 kg/sqcm and fixing all special such as plain bends, off sets, door bends, single junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including coast and conveyance of all materials, labour charges etc., complete for finished item of work at all floor levels.

110 mm dia pipe: Supplying and fixing of SWR/PVC pipes (as per ISI standards) 4 kg/sqcm and fixing all special such as plain bends, off sets, door bends, single junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including coast and conveyance of all materials, labour charges etc., complete for finished item of work at all floor levels.

Constructing 457.2mm x 457.2mm (1'6" x1'6") brick in CM(1:6) prop. Masonary Inspection chamber upto 914.4mm (3'0")and fitted withlight weight 457.2mm x 457.2mm (1'6" x1'6") C.I. Frame and cover of 20 Kg including excavating pits upto a depth of 450mm (1'-6") in all sorts of soils (excluding rock) and laying cement concrete (1:4:8) 150mm thick using 40mm HBG mtal and P.C.C. (1:2:4) prop. benching and channel 100mm thick as per standard specification and including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, cost all incidental and operational, labour charges like mixing cement mortar, constructing masonary, lift charges, lift charges, curing etc., complete for finished item of work as per standard specification.

Providing cess pool with RCC rings dia 1.20 mtrs with 40 mm thick 230 mm height of precast RCC Rings including cover excavation of pit 1.50 mtrs dia up to a depth of 2.4 mtrs lowering the RCC rings 10 nos in the well and providing pointing with C.M 1:3 prop includingthe refilling the excavated earth and cost and conyeyance of all materials labour charges etc., complete as directed by the department.

Supply & Fixing of tested NP bib taps heavy duty of short body seiko / ESSO or equilent make at all levels of size 12.70mm dia of Indian make first quality including cost and conveyance of all materials, labour charges etc., complete for finished item of work.

Gully trap: Supplying and fixing 150.00mm x 100.00mm SWG gully trap conforming to ISI 651 & 4127 with CI grating and constructing brick masonry intermediate chamber in CM (1:6) prop. and fitted with RCC cover 3" thick as directed by Engineer-in-charge including cost and conveyance of all materials to site, labour charges etc., complete for finished item of work.

Supplying and fixing of RAJSHRI or equivalent SINGLE SIDE PRELAM SOLID PANEL PVC DOOR FRAME (CHOUKHAT) Providing and fixing factory made Pac single side prelam door frame of the size 50mm x 47mm with a wall thickness of 5mm, made out of extruded 5mm rigid Pac single side prelam sheet, meter cut at two corners and joined with 2 no’s of 150mm long brackets of 1515mm MS Square tube. The two vertical door profiles are to be reinforced with 19mm x 19mm MS Square tube of 19guage. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using pac fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 no’s for horizontal member etc., complete as per manufacture specification and direction of Engineer-in-charge.

Supply and fixing of door shutters made of rigid PVC extruded hollow section of 20mm X 200 mm with the wall thickness of 1.0mm +/- 0.1mm equally divided into 4 no's with tongue and groove locking arrangements. The shutter frame is made of 30mm X 79mm with the wall thickness of 1.5mm+/-0.15mm section mitre-cut and joined at 4 corners with 125mm X 225mm plastic brackets. The shutter shall be horizontally reinforced with 2 no's of 8mm PVC rods. Teak wood batons shall be reinforced inside the door shutter during the fabrication of the door shutter at those points wherever the hardware is fixed onto the door shutter complete as directed by the engineer in charge including labour charges for fixing.