REPAIR AND MAINTENANCE OF CHARPOY GI/BED OF OTM AND MD ACCN AND MISC CHAIRS INCLUDING THEIR PAINTING AND POLISHING UNDER GE NORTH BINNAGURI

Amount

Charpoy GI Pipe with Nylon Newar/Charpoy GI Pipe with Ply Top (Drawing No. FD -220)

Taking out and removing all existing unserviceable worn out nylon newar from Charpoy, tightening the frame and S & F new ply wood 12 mm thick BWR grade (07 layer ) ISI marked including three stiffener of size 900mm x 50mm x 5mm made of MS flat iron and applying two coats of Black synthetic enamel paint over a coat of red oxide, the stiffener shall be welding with long rail of Charpoy GI pipe and ply shall be fixed with support of counter sunk nut, bolts and washer (75mm x 6mm, total 10 Nos) including 3 Nos holes on each long rail and 02 Nos holes on each short rails, complete all as specified and directed.

Taking out and removing all existing unserviceable plywood top from Charpoy GI Pipe, tightening the frame and S & F new plywood top 12 mm thick BWR grade 07 layer ISI marked, with support of counter sunk nut, bolts and washer of size 75mm x 6mm (total 10 Nos ). The existing stiffeners shall be fixed to long rails with welding and applying two coats of black paint, complete all as specified and directed.

Taking out and removing old unserviceable long rail from its position and including separating serviceable position of the same for making short rail and S&F new long rail as per existing shape and size made out of 32mm bore GI pipe medium grade (ISI marked ) and fixed the same in the existing position with making thread at both end complete all as specified and as directed as shown on drawing.

Taking out and removing old unserviceable short rail from its position and including separating serviceable position of the same for making leg and S&F new short rails as per existing size, made out of 32mm bore GI pipe (ISI marked) fixed in the existing position complete all as specified and as directed as shown on drawing.

Taking out and removing old unserviceable legs from its position and S&F new legs from its position and as per existing size made out of 32mm GI pipe med grade and fixed the same in the existing position with making thread at one side, 02 Nos MS clamp fixed on each leg for staying MNF, and washer 40 x 3mm thick welded to bottom of each leg complete all as specified and as directed as shown on drawing.

Taking out and removing old unserviceable stiffeners from its position and S&F new stiffeners to the same in existing position, size 900mm x 50mm x 5mm thick made of MS flat iron and applying two coats of Black synthetic enamel paint over a coat of red oxide complete all as specified and as directed as shown on drawing.

Labour only for making short rail from long rail as obtained from GI Pipe against Serial No 1.03 here-in-before cut to required length including making thread at one or both end whenever required and removing balance short pieces of GI pipe from site complete all as specified and as directed.

Labour only for making leg from short rail as obtained from GI Pipe against Serial No 1.04 here-in-before cut to required length including making thread at one end of each leg as required and removing balance short pieces of GI pipe from site complete as specified and as directed.

Taking out and removing old unserviceable three way Elbow from its position and S & F new 32mm dia three way GI elbow medium grade (ISI marked ) in the existing position complete all as specified and as directed as shown on drawing.

Taking out and removing old unserviceable GI check nut from its position and S & F new 32mm dia and 6mm thick GI medium grade check nut & fixed in the same position complete all as specified and as directed as shown on drawing.

S & F in repair new mild steel clamp by welding made out of flat iron of size 25mm x 3mm thick made in to existing shape and size with one GI washer fixed at the bottom of clamp by welding including painting the steel surface with apply two coats of black synthetic enamel paint (2nd grade quality) over a coat of red oxide primer complete as specified as directed and as shown on drawing.

Taking and removing of unserviceable hard wood shoes from its position and S & F new hard wood shoes round block made of well seasoned 1st class sal wood and fixed with new steel screws to bottom of leg complete shape and size all as specified and directed.

Charpoy IP with Hard Top (Drawing No. FD/MAP-II/ 01)

Taking out old damaged / broken plywood from its position and refixing the same with new 12mm thick plywood (BWR grade) 07 layer shall fixed with counter sunk nut, bolts and washer as per existing shape complete all as specified and as directed.

Taking out old damaged / broken stiffener from its position and refixing the same with new stiffener of size 25mm x 25mm x 16 gauge MS tube shall be fixed through spot welding complete all as specified and as directed. Note : Thickness of metal to be welded shall not exceed 2mm.

S&F new rubber shoes of best quality to the bottom of leg complete all as specified and as directed as shown on drawing.

M&L for one coat of Black synthetic enamel paint (1st grade quality) on all exposed steel surface of Charpoy hard top complete all as specified and as directed.

BED HARD STEEL (Drawing No. FD/E6/MAP/08 (R))

Taking out old damaged / broken plywood from its position and refixing the same with new 12mm thick plywood (BWR grade) 07 layer shall fixed with counter sunk nut, bolts and washer as per existing shape complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken stiffener from its position and refixing the same with new stiffener of size 25mm x 25mm x 16 gauge MS tube shall be fixed through spot welding complete all as specified and as directed as shown on drawing. Note : Thickness of metal to be welded shall not exceed 2mm.

S&F new rubber shoes of best quality to the bottom of leg complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken Head board / foot board from its position and S&F new Head board / foot board made with 18/19 mm thick one side pre-laminated particle board of exterior grade as per existing of Mysore teak face colour complete all as specified and as directed as shown on drawing.

M&L for one coat of Black synthetic enamel paint (1st grade quality) on all exposed steel surface of Bed hard steel complete all as specified and as directed.

Bed Hard Plywood (Drawing No. FD-246/245/213)

Taking out old damaged / broken plywood from its position and refixing the same with new 12mm thick plywood (BWR grade) 07 layer shall fixed with screw as per existing shape complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken long rail from its position and S&F new long rail using 1st class seasoned Teak wood complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken Stiffener from its position and S&F new stiffeners using 1st class seasoned Teak wood complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken Head board from its position and S&F new Head board using 1st class seasoned Teak wood all complete all as specified and as directed as shown on drawing.

Taking out old damaged / broken Foot board from its position and S&F new Foot board using 1st class seasoned Teak wood all complete all as specified and as directed as shown on drawing.

M&L for applying wood touch polish with high glossy finish in all wooden surface of Bed Hard plywood top including preparation of surfaces including applying wood filler wherever required complete all as specified and as directed and as shown on drawing.

Chair Writing (Drawing No. FD-20(M), FD-250/ FD-280)

Taking out old damaged/decayed front leg from its position and S & F new front leg & fixing as per existing size and section in the same position made out of seasoned ‘Teak Wood’ timber including applying wood touch polish with high glossy finish over wood filler on all exposed timber surfaces complete all as specified and as directed as shown on drawing.

All as per serial item No 5.01 here in before but for rear leg.

Taking out old damaged/decayed side rail left/right from its position and S & F new side rails in the same position as per existing shape and size made out well seasoned ‘Teak Wood’ timber with making holes for canning including applying wood touch polish with high glossy finish over wood filler as required on all exposed timber surfaces complete all as specified and as directed as shown on drawing.

All as per Serial item No 5.03 here in before but for Front/Rear rail.

Taking out old damaged/decayed bottom stiffener from its position and S & F new bottom stiffener all as existing shape and size in the same position made out well seasoned ‘Teak Wood’ timber including applying wood touch polish with high glossy finish over wood filler on all exposed timber surfaces complete all as specified and as directed as shown on drawing.

All as per Serial item No 5.05 here in before but for back rest.

All as per Serial item No 5.05 here in before but for hand rest (left/right).

Taking out and removing old unserviceable worn-out of plastic cane from chair writing and recanning the same with white new plastic cane half round oval type 2mm wide, 0.4mm thick for weaving and 4mm wide for boarding (Godrej Pattern) complete all as specified and as directed as shown on drawing.

Taking out of all old unserviceable rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws as approved, complete all as specified and as directed as shown on drawing.

M & L for applying wood touch polish with high glossy finish to all exposed wooden surfaces after preparation of surface including applying wood filler to components wherever required complete all as specified and as directed as shown on drawing.

Chair Dining (Drawing No. FD-16(M)/ FD-228/FD-279/ FD-1105)

Taking out old damaged/broken front leg from its position and S&F new front leg on the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber with providing hard rubber shoe at bottom of leg complete all as specified and as directed as shown on drawing.

All as per ser No 6.01 above but rear leg.

Taking out old damaged / broken seat rail (front / back) from its position of chair dining and S&F new seat rail of front / back side in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber and making holes for canning with slightly rounded on the edges of the holes complete all as specified and as directed as shown on drawing.

All as per ser No 6.03 above but side rails (left / right).

Taking out old damaged / broken leg stiffener from its position and S&F new leg stiffener in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber complete all as specified and as directed as shown on drawing.

All as per Ser No 6.05 above but of back rest.

Taking out and removing all unserviceable worn out plastic cane from seat of chair dining and re-canning the same with new white plastic cane of 2mm wide, 0.4mm thick half round (oval type) for weaving and 4mm wide for bordering as per Godrej pattern complete all as specified and as directed as shown on drawing.

Taking out of all old unserviceable rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws as approved, complete all as specified and as directed as shown on drawing.

M & L for complete polishing of the all exposed wooden surfaces shall be wood touch polished with high glossy finish after necessary preparation of surface matching with replaced/existing parts complete all as specified and as directed as shown on drawing.

Chair Wooden Bottom (Drawing No. FD-56(M)/FD-225)

Taking out old damaged/decayed front leg from its position and S & F new front leg as per existing shape and size in the same position made out of well seasoned ‘Teak Wood’ timber complete all as specified and as directed as shown on drawing.

All as per item Ser No 7.01 here-in-before but for rear leg.

Taking out old damaged/decayed side rail (Right/Left) from its position and S & F new side rail as per existing shape and size in the same position made out of well seasoned ’Teak wood’ timber complete all as specified and as directed as shown on drawing.

All as per item No 7.03 here-in-before but for front / rear rail.

Taking out old damaged/decayed bottom stiffener from its position and S & F new stiffener in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber complete all as specified and as directed as shown on drawing.

All as per item No 7.05 here-in-before but for back rest

Taking out old damaged/decayed ply wood seat from its position and S & F new seat ply of 6mm thick BWR type in the same position as per existing shape and size complete all as specified and as directed as shown on drawing.

Taking out of all old unserviceable rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws as approved, complete all as specified and as directed as shown on drawing.

M/L for applying wood touch polish with high glossy finish to all exposed wooden surfaces including preparation of surfaces applying wood filler to new components complete all as specified and as directed as shown on drawing.

Chair Easy (Drawing No. FD-17(M)/ FD-229)

Taking out old damaged/decayed front leg from its position and S & F new front leg in the same position as per existing shape and size made out of well seasoned ‘Teak Wood’ timber including providing hard rubber ring fixed with screws at the bottom of the leg including applying wood touch polish with high glossy finish over wood filler over exposed new timber surfaces complete all as specified and as directed as shown on drawing.

All as per item No 8.01 above but for rear leg.

Taking out old damaged/decayed back front top rail from its position and S & F new top rail in the same position as per existing shape and size made out of well seasoned ‘Teak wood' timber including making holes for re-canning including applying wood touch polish with high glossy finish over wood filler on exposed new timber surfaces complete all as specified and as directed as shown on drawing.

All as per item Ser No 8.03 above but for side top rail (left/right).

All as per item Ser No 8.03 here-in-before but for rear top rail.

Taking out old damaged/decayed bottom side rail (right/left) from its position and S & F new side rail in the same position as per existing shape and size made out of well seasoned ‘Teak wood timber including applying wood touch polish with high glossy finish over wood filler wherever required overexposed new timber surfaces complete all as specified and as directed as shown on drawing.

all as per item Ser No 8.06 above but for front/rear bottom rail.

Taking out and removing all unserviceable worn out plastic cane from seat and back of chair easy and re-canning the same with new white plastic cane 2mm wide, 0.4mm thick oval type in seat and back by weaving and 4 mm wide for bordering complete all as specified and as directed as shown on drawing.

Taking out old damaged/decayed hand rest from its position and S & F new hand rest in the same position as per existing shape and size made out of well seasoned ‘Teak wood’ timber including applying wood touch polish with high glossy finish over wood filler over exposed new timber surfaces complete all as specified and as directed as shown on drawing.

Taking out of all old unserviceable rubber/PVC shoes and S & F new hard rubber/PVC shoes with screws as approved, complete all as specified and as directed as shown on drawing.

M&L for applying wood touch polish with high glossy finish to exposed wooden surfaces including preparation of surfaces applying wood filler wherever required complete all as specified and as directed as shown on drawing.

Chair Verandah (Drawing No. FD-256/FD-359)

M & L in repairs to broken steel frame not exc 2.5 cm in length by spot welding complete all as specified and as directed as shown on drawing. Note: Material to be welded not to exceed 2.00mm in thickness.

M & L for painting of steel frame of chair verandah with one coat of white synthetic enamel paint (1st grade quality) after preparation of old steel surfaces including applying one coat of red oxide primer and one coat of white synthetic enamel paint over newly welded surfaces complete all as specified and as directed as shown on drawing.

Taking out old existing damaged/ worn out unserviceable plastic cane/newar from seat and back of chair verandah and supply and fix the same seat and back with new white cane 4mm wide 1mm thick half round (oval type) mat pattern as per trade practice complete all as specified and as directed as shown on drawing.

Taking out old unserviceable shoes from leg of chair verandah and S&F new hard rubber shoes of best quality complete all as specified and as directed as shown on drawing.

Chair CB Steel with Arm (Drawing No. FD-75(M))

M & L for spot welding to damaged/broken steel frame of chair CB steel including arms complete all as specified and as directed as shown on drawing. Note: Length of each spot welding 4cm in length and not exc. 2mm in thickness.

Taking out old rusted/damaged/broken flat iron support of chair CB steel with arms and S&F new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as directed as shown on drawing.

Taking out old damaged/broken arm rest and S & F new arm rest in the same position as per existing shape and size made out of well seasoned first class hard wood ‘TEAK WOOD’ timber including applying wood touch polish with high glossy finish to exposed wooden surfaces including preparation of surfaces applying wood filler wherever required complete all as specified and as directed as shown on drawing.

Taking out old damaged/broken seat frame and S & F new seat frame in the same position as per existing shape and size made out of well seasoned first class hard wood ‘TEAK WOOD’ timber with making holes of weaving slightly rounded on the edges and applying wood touch polish with high glossy finish to exposed wooden surfaces including preparation of surfaces applying wood filler wherever required including recanning with plastic cane to seat of chair in white colour half round Godrej pattern with 2mm wide 0.4mm thick for weaving and 4mm wide for bordering and 0.4mm thick gola type, weighing not less than 6 gms per 10 running meters complete all as specified and as directed as shown on drawing.

All as per ser item No 10.04 here in before but back frame complete all as specified and as directed.

Taking out old unserviceable top cap and S&F new plastic cap of best quality in the same position complete all as specified and as directed.

M & L for applying painting to steel frame of chair CB steel with arms with one coat of OG synthetic enamel paint (1st grade quality) after necessary preparation of old painted surfaces by spray machine over one coat of redoxide primer complete all as specified and as directed as shown on drawing.

Taking out old unserviceable shoe & S&F new hard rubber shoe with screw as approved complete all as specified and as directed as shown on drawing.

Chair Writing (Drawing No. FD/E6/MAP/12)

Taking out old damaged / decayed tapestry cloth from seat /back of chair and replace it with new tapestry cloth as per existing shape after approval of tapestry cloth complete all as specified and as directed as shown on drawing. Note : The cost of tapestry cloth shall not be less than Rs. 275/- per mtr.

Taking out old damaged / decayed seat / back of chair and S&F new seat/ back, shall be of 12 mm thick hot pressed plywood up hoistered with fabric and moulded polyurethane foam ( shall be 50 mm thick and moulded with density 50.55 kg per cubic mtr) with pvc lapping all around as per existing shape after approval of tapestry cloth complete all as specified and as directed as shown on drawing. Note : The cost of tapestry cloth shall not be less than Rs. 275/- per mtr.

Taking out old damaged / decayed handle from chair and Supply and fixing a pair of arms made out of black integral skin polyurethane with 75-85 shore 'A' hard ness and reinforced with MS insert along with nut & bolt where required to chair writing complete all as specified and as directed as shown on drawing.

M & L for spot welding to damaged/broken steel frame of chair writing complete all as specified and as directed as shown on drawing. Note : Length of each spot welding 4cm in length and not exc. 2mm in thickness.

Taking out old unserviceable shoe & S&F new hard rubber shoe with screw as approved complete all as specified and as directed as shown on drawing.

M&L for preparation of old painted steel surfaces of chair writing and applying one coat of black enamel paint (1st grade quality) on all exposed steel surfaces complete all as specified and as directed as shown on drawing.

Chair Computer / chair revolving with arms (Drawing No. FD/E6/MAP/01)

Taking out old damaged / decayed tapestry cloth from seat /back of chair and replace it with new tapestry cloth as per existing shape after approval of tapestry cloth complete all as specified and as directed as shown on drawing. Note : The cost of tapestry cloth shall not be less than Rs. 275/- per mtr.

Taking out old damaged / decayed seat / back of chair and S&F new seat/ back, shall be of 12 mm thick hot pressed plywood up hoistered with fabric and moulded polyurethane foam ( shall be 60 mm thick and moulded with density 50.55 kg per cubic mtr) with pvc lapping all around as per existing shape after approval of tapestry cloth complete all as specified and as directed as shown on drawing. Note : The cost of tapestry cloth shall not be less than Rs. 275/- per mtr.

Taking out old damaged / decayed handle from chair and Supply and fixing new a pair of arms made out of black integral skin polyurethane reinforced with MS insert (It shall be scratch and weather resistant ) as per existing shape and size in the same position complete all as specified and as directed as shown on drawing.

Taking out old damaged/unserviceable multi locking hydraulic mechanism from chair and S&F new multi locking hydraulic mechanism as per existing shape and size in the same position complete all as specified and as directed as shown on drawing.

Taking out old damaged / decayed twin wheel castors from chair and S&F of new twin wheel castors as per existing shape and size in the same position complete all as specified and as directed as shown on drawing.

Chair Dining JCO/OR (Drawing No. FD/MAP-II/ 05)

Taking out old damaged/decayed front leg from its position and S & F new front leg as per existing shape and size in the same position made out of well seasoned ‘Teak wood" timber including Hard rubber ring complete all as specified and as directed as shown on drawing.

All as per item Ser No 13.01 here-in-before but for rear leg complete all as specified and as directed as shown on drawing.

Taking out old damaged/decayed seat rail (Front/ back, left/ right) from its position and S & F new seat rail in the same position as per existing shape & size made out of well seasoned ‘Teak wood’ timber complete all as specified and as directed as shown on drawing.

Taking out old damaged/decayed leg stiffener from its position and S & F new leg stiffener as per existing shape and size in the same position made out of well seasoned ‘Teak wood’ timber complete all as specified and as directed as shown on drawing.

All as per item Ser No 13.04 here-in-before but for back rest complete all as specified and as directed as shown on drawing.

Taking out and removing all unserviceable worn out PVC seat frame of Chair Dining JCOs/OR and S & F new PVC seat frame complete all as specified and as directed as shown on drawing

M & L for applying wood touch polish with high glossy finish to all wooden surfaces both old and new surfaces after necessary preparation of surfaces including wood filler to complete all as specified and as directed as shown on drawing.

S & F new seat stiffener fixed to middle of seat rail made out of well seasoned ‘Teak wood’ timber (size 25 x 25mm) , complete all as specified and as directed.

Chair Verandah (Drawing No. FD/MAP-II/ 15)

M&L for spot welding in repairs not exc 2.50cm in length of broken steel frame complete all as specified and as directed as shown on drawing. Note : Material to be welded not to exceed 2.00mm in thickness.

M&L for applying one coat of white synthetic enamel paint (Ist grade quality) on all exposed steel surface of chair verandah including preparation of old painted surface complete all as specified and as directed as shown on drawing.

Taking out old existing damaged / broken seat frame of chair verandah and supply & fix new seat frame complete all as specified and as directed as shown on drawing.

Taking out old existing damaged / broken back frame of chair verandah and supply & fix new back frame complete all as specified and as directed as shown on drawing.

S&F new hard rubber shoes of best quality complete all as specified and as directed as shown on drawing.

M/s. RAMPHAL GARG

PRAVESH KUMAR

M/S MAJUMDER CONSTRUCTION