Construction work of Bus terminal in Ranikhet (Almora)

Amount

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):15.8.3 From brick work in cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete..

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Sepration Membrane of Impermeable Plastic Sheeting 125micron Thick

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade 'A' sealing compound conforming to IS: 1834.

Steel work welded in built-up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor,apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of building shall be measurd for payment.)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All work upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

White washing with lime to give an even shade : New work (three or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 10.14.1 Profile B 10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm

Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete :150 mm

Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Steel work welded in built-up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in-charge: With Type N - Normal 50 mm thick

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing white viterous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing water closet water closet squatting pan (Indian Type W.C Pan) with 100mm sand cast iron 'P' or 'S' trap, 10 ltrs low level, PVC flushing cistern with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever requiredand as per direction of Engineer -In-charge: White Vitreous China Orissa pattern W.C pan of size 580 x 440 mm with integral type foot rests.

Providing and fixing C.P. brass short body bib cock with flange of approved quality confirming to IS: 8931 15mm nomonal bore

Providing and fixing wash basin with CI/MS brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fitting and brackets, cutting and making good the walls wherever required. White Vitreous China wash basin (oval) size550 x 400 mm with single 15mm CP brass pillar tap

Providing and fixing wash basin with CI/MS brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fitting and brackets, cutting and making good the walls wherever required. White Vitreous China flat back wash basin size550 x 400 mm with single 15mm CP brass pillar tap

Providing & fixing PTMT Bottle trap for wash basin and sink Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass union and G.I clamps complete, including painting and brakets, cutting and making good the walls and floor wherever required One urinal basin with 5 litre white PVC automatic flushing cistern

Providing and fixing C.P. brass quality angle valve15 mm dia. For basin mixer and gyser points of approved quality, confirming to IS : 8931 15mm nomonal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confirming to IS : 8931. 15mm nomonal bore

Providing & fixing PTMT liquid soap container109mm wide,125mm high and 112mm distance from wall of standard shape and brackets of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long,200mm wide with a minimum distance of 37mm from wall face with concealed fitting arrangement of approved quality and colour weighing not less than 88 gms.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing & fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washer complete.

Providing and fixing toilet paper holder C.P. brass

Providing and fixing soil, waste and vent pipes: 100 mm dia Centrifugally cast (spun) iron socketed pipe as per IS 3989.

Providing and fixing soil, waste and vent pipes: 100 mm dia Centrifugally cast (spun) iron socketed pipe as per IS 3989 75 mm

Providing and fixing M.S holder-bat clamps of approved design to sand cast iron/sand cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1cement:2coarse sand: 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc For 100 mm dia pipe

Providing and fixing M.S holder-bat clamps of approved design to sand cast iron/sand cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1cement:2coarse sand: 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc For 75 mm dia pipe

Providing and fixing bend of required degre with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Providing and fixing plain bend of required degree 100 mm Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Providing and fixing plain bend of required degree 75 mm Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Providing and fixing single equal plain junction of required degree with access door, insersion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S & S as per IS 3989

Providing and fixing single equal plain junction of required degree with access door, insersion rubber washer 3 mm thick, bolts and nuts complete. 75x75x75 mm Sand cast iron S & S as per IS 3989

Providing and fixing double equal plain inverted branch of required degree 100x100x100x100 mm Sand cast iron S & S as per IS 3989

Providing and fixing terminal guard. 100 mm Sand cast iron S & S as per IS 3989

Providing and fixing terminal guard. 75 mm Sand cast iron S & S as per IS 3989

Providing and fixing collar 100 mm Sand cast iron S & S as per IS 3989

Providing and fixing collar 75 mm Sand cast iron S & S as per IS 3989

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 100 mm

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 75 mm

Providing and fixing M.S stays and clamps for sand cast iron / Centrifugally Cast (Spun) Iron Pipes iron pipes of diameter. 100 mm

Providing and fixing M.S stays and clamps for sand cast iron / Centrifugally Cast (Spun) Iron Pipes iron pipes of diameter. 75 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This include jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. 50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This include jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. 62.50 mm nominal outer dia Pipes

Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 15 mm nominal bore

Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 20 mm nominal bore

Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 25 mm nominal bore

Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 32 mm nominal bore

Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 40 mm nominal bore

Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 50 mm nominal obore

Providing and placing on terrace (at all floor levels polyethylene water storage tank ISI : 12701 marked water storage tank with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base suport for tank

Constructing masonary chamber 30x30xx50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement : f fine sand) for gate valve with C. I. susface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 ( 1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with F. P. S. bricks

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm Dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110mm Bend

Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing 40mm dia with length not less than 700mm waste pipe for sink and wash basin. complete job.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :100 mm dia. R.C.C. pipe

Supply, installation, testing and commissioning of horizontal single stage centrifugal type factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP-55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles AC. Capacity 2280 LPM at 70m Head & 3.5 Kg/cm2 delivery pressure for Fire Hydrant Network.

Capacity 180 LPM at 70m Head & 3.5 Kg/cm2 (Jockey Pump).

Supply, installation, testing and commissioning of horizontal single stage centrifugal pumping set with CI volute and bronze impeller with mechanical seals directly coupled to automatic Diesel Engine complete with all accessories like self starting by means of Battery powered electric starter motor, Paper Filter type air cleaner, exhaust silencer etc. complete in all respects. The engine & the pump will be mounted on common base plate on anti-vibration mountings. Capacity 2280 LPM at 70m Head & 3.5 Kg/cm2 delivery pressure for Fire Hydrant & Sprinkler Network.

Providing & fixing 150 mm diameter M.S. Class 'C' diesel pump exhaust pipe includings all fittings, like bends, tees etc. clamps / structural steel supports. The pipe shall be provided with 75mm thick fiberglass insulation & covering the insulation with 500 g polythene sheet giving proper overlaps & sealing the joints with suitable adhesive compound. The pipe shall be provided with 24 gauge aluminium sheet cladding

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drainarrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150 mm dia

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve &nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying and fixing single headed internal hydrant valve with stantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal /Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way-150 mm dia M.S. Pipe

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Constructing masonary chamber 90 x 90 x100 cm. inside with 75 class designation brickwork in cement mortar 1:5 ( 1 cement : 5 fine sand) for sluice valve with CI surface box 100 mm top dia. 180 mm bottom dia. And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and inside plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with FPS bricks

Providing and fixing C.I. double acting air valves of approved quality with bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if reqd. will be paid separately) 50 mm dia.

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) Class II

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 150 mm dia.

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 80 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 100 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 80 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 100 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 200 mm dia

Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required

Providing laying, testing & ommissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 nominal bore (class C)

Providing laying, testing & ommissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 200 nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 100 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 80 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 65 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 50 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 40 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 32 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the all/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 25 mm nominal bore (class C)

Providing, fixing, testing & ommissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven chanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges,emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :80mm dia

Providing, fixing, testing & ommissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven chanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges,emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :150mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Horizontally Side wall type

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent type Sprinkler

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1200mm

Supplying and Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with charcoal/ coke and salt as required.

Supplying and laying 25 mm x 5 mm. G.I. strip in 40 mm dia. G.I. Pipe from earth electrode, including connection with GI nut, bolt, spring, washer excavation and re-filling etc as required.

Providing & fixing 25mm x 5mm G.I. strip on surface or in recess for connections etc. as required.

Providing and Fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, fabricating and installing following size of perforated painted with powder coating M.S. cable trays,with perforation not more than 17.5%, in covenient section, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying, fabricating and installing following size of perforated painted with powder coating M.S. cable trays,with perforation not more than 17.5%, in covenient section, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size not exceeding 35 sqmm on surface as required.

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of folloing size on wall surface as required. Aboved 35 sq mm and upto 95 sq mm (clamed with 25x3mm MS flat clam)

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 120 sq. mm. Armoured Aluminium cable.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 35 sq. mm. Armoured Aluminium cable.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 16 sq. mm. Armoured Aluminium cable.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 5C x 1.5 Sq. mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed steel conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.( Lift well )

Wiring for group controlled (looped) light point / fan point / exhaust fan point/ call bell point (without independent switch etc.) with1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.-group-C

Wiring for circuit wiring alongwith earth wire with the following sizes of HR-FR-LSH-lead free copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copperconductor single core cable for loop earthing as required. (FOR POWER PLUG )

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire for floor panel to L- DB

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire for floor panel to P-DB

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required.

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 16 Amp universal modular socket outlet and 15/16 amps modular switch,connection, painting etc as required.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and fixing of Following sizes of PVC conduit along with the accessories like Junction boxes, bends, socket, fish wire etc. on surface/recess with M.S. Clamps, nuts and bolts including cutting of the wall and making good the same in case of recessed conduit as required. for LV 20mm

Supplying and fixing of Following sizes of PVC conduit along with the accessories like Junction boxes, bends, socket, fish wire etc. on surface/recess with M.S. Clamps, nuts and bolts including cutting of the wall and making good the same in case of recessed conduit as required. for LV 25mm

Supplying and fixing of Following sizes of PVC conduit along with the accessories like Junction boxes, bends, socket, fish wire etc. on surface/recess with M.S. Clamps, nuts and bolts including cutting of the wall and making good the same in case of recessed conduit as required. for LV 32mm

Supplying and fixing of Following sizes of PVC conduit along with the accessories like Junction boxes, bends, socket, fish wire etc. on surface/recess with M.S. Clamps, nuts and bolts including cutting of the wall and making good the same in case of recessed conduit as required. for LV 40mm

Supply, fixing, connecting and testing of telephone / computer / TV modular sockets modular plate anodised MS box and blanking plate in surface / recessed including connectionetc as required. RJ-11 telephone socket two line with shutter

Supplying and drawing following pair, 0.5 sq.mm. FR PVC insulated copper conductor, unarmoured telephone cable in existing surface/ recessed steel/ PVC conduit as required. 2 pair Telephone cable ( 0.5 sq.mm. )

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator) 8 way (4 + 24), Double door L-DB + P DB+U DB

Supplying and fixing upto following amps rating, 240/415 volts, “C”curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. 6-32 Amp (10KA) SP MCB 'C' Series

Installation, testing and commissioning of pre-wired,fluorescent fitting / compact fluorescent fitting/ LED Light fitting of all types,complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc.as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable,including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation, testing and commissioning of exhaust fan up to 450 mm sweep in the existing opening,including making the hole to suit the size of the above fan, making good the damage complete , connection , etc as required.-M/C ROOM & PUMP ROOM

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supply and Installation 6 SWG G.I. wire on surface or in recess for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 95 sq. mm and upto 185 sq. mm

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 95 sq. mm and upto 185 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 4Cx10 sq. mm (25mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 4Cx16 sq. mm (28mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 4 X 25 sq. mm (28mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 50 sq. mm (35mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 70 sq. mm (38mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 95 sq. mm (45mm

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 150 sq. mm (50mm)

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 185 sq. mm (57mm)

Laying of one number XLPE power cable of 33 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Upto 120 sq. mm

H.T Termination: Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 120 Sq.mm

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11KV grade as required 120 Sq.mm

Hot Dipped Galvanized Iron Cable Tray 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as requiredSupplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement) 150 mm width X 50 mm depth X 1.6 mm thickness

Hot Dipped Galvanized Iron Cable Tray 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as requiredSupplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement) 300 mm width X 50 mm depth X 1.6 mm thickness

Hot Dipped Galvanized Iron Cable Tray 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as requiredSupplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement) 450 mm width X 50 mm depth X 2.0 mm thickness

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single Red colour on front side as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required 150 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required 63 mm dia (OD-63 mm & ID-51 mm nominal

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal)

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required Above 6.5 meter and upto 8.0 meter

Suspended floors, roofs, landings, balconies and access platform

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

In all kind of soil upto 3.0m to 4.5m. depth

In all kind of soil upto 4.5 m to 6.0m. depth

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: With 20x20mm square bar

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. Drilling of 300mm dia bore hole manually.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Gravel/Soil-Aggregate Base (Table 400.2) Grading C Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Cement Concrete Pavement Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 Cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Landscapping and Horticultural work

Supply and fixing of Fire Shaft door fabricated out of G.I. Sheet and frame, door shall be 900mm x 1500mm min with double leaf. & fixed with 4 mm thick Glass, suitable Rubber beeding and Locking arrangment. Quoted rate shall be included alll fasterners etc, and complete shutter shall be powder coated of approved colour both inside and out side.

Hose cabinet stand mounted type fabricated out of M.S. sheet of 16 swg. With glass fronted (4mm thick glass with rubber beading) door and size of the cabinet shall be 600x750x250mm Quoted rate shall be inlcludes suitable stand for mounting for ground level with sup[orts all fastners etc, and cabinet shall be painted/powder coated of approved colour both inside and out side.

SS 63mm dia single outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

63mm dia twin outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

Providing/Fixing Fire man axe. Make.

CO2 type Fire exitinguisher ISI marked confirming to IS:15683 lates. Capacity 4.5 kg complete with delivery hose horn, squeeze grip release valve, locking arrangement, operating temperature -30°c to +55°c, supplied with body bearing IS 7285 mark and approved valve as per IS 3224. Co2 Gas as per IS:15222. externally painted with PO Red Shade No. 538 of IS 5, operation manual and floor stand or wall mount Bracket including accessories as required as per site condition. 4.5KG

Powder Fire exitinguisher (stored Pressure Type) (Powder pressurized with dry nitrogen gas at 15 bar) capacity 4kg duly ISI marked conforming to IS:15683:2006/latest, with IS 14609 ISI marked ABC powder complete with squeeze grip release valve, discharge pipe, locking arrangment, pressure gauge, operation maual, Body Hydrotested at 35 bar, operating temperature--30°c to +55°c, external epoxy powder coating with PO Red shade No. 538 of IS 5, and floor stand or wall mount Bracket including accessories as required as per site condition. 4.5 KG

Providing and fixing mechanical foam type Trolley Mounted Fire Extinguisher of bearing to IS:10568/IS13385/IS13386 with dis Capacity 45 Lit.

Providing and fixing Carbon Dioxide Type Trolley Mounted Fire Extinguisher of as per IS: 2878 with discharge time of 10 to 20 sec/15 to 36sec/20 to 60sec respectively. 22.5 Kg. CO2 Fire Extinguisher

FIRE ALARAM

Data -I/O (RJ-45 Connectors) + Dats Face Plate

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB),having a sensitivity current upto 100 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp SPN RCCB with 100 ma fault current rating

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB),having a sensitivity current upto 100 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amp SPN RCCB with100 ma fault current rating

Supplying and fixing upto following amps rating, 240/415 volts, “C”curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. 63A FP MCB

Supplying and fixing upto following amps rating, 240/415 volts, “C”curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. 40A FP MCB

Supply of lighting fixtures of surface mounted 15W LED Round Downlighter luminaire. The LED source used shall be complying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaire of a minimum of 100 lms/W with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.95, THD<10% and Surge Protection of atleast 3.5KV.

Supply of lighting fixtures of surface mounted 12W LED Round Downlighter luminaire. The LED source used shall be complying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaire of a minimum of 100 lms/W with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.95, THD<10% and Surge Protection of atleast 3.5KV.

20 W linear 4ft LED integrated batten made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. These end caps are snap-fitted to the fixture.High efficiency long life LED with lumen efficacy of 130 lm/W with viewing angle of 120º.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection.Can be fixed directly into the wall/ ceiling by means of mounting SS clips provided with the fixture. Lumen Output of 2110 lumens with System efficacy of >105lm/W .CRI >80, Color temperature 6500K, THD <20% and PF>0.95,IP20 . Life class of 35,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ.

Supply of 10W LED BulK head Fitting, The LED source used shall be complying with LM80 standards & LED source efficacy >120 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaire of a minimum of 100 lms/W system efficacy with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20%,IP65 and Surge Protection of atleast 5KV.

Supply of 120W flood light

Supply of 200W flood light

Supply of 200 W+/-1 W Linear Low Glare LED High bay luminaire, surface/ suspension mounted, Aluminum extruded housing with powder coating, PC lens diffuser, system lumen efficacy 145 lm/W with minimum system lumens of 29000 and having availability of beam angle of 60 degree and assymertic beam, and with option of tilting arrangement . The luminaire shall have IP66 protection. The LED shall be compliant with Useful L70B50 life of >75000 Hrs. Driver efficiency should be 85% in input voltage range of 140V to 280V (nominal rated voltage – 240V) with 6 KV internal surge protection.Make: Philips, Wipro, Trilux.

Supply of Led fixture 600mmX600mm 40 W+/- 1W Surface Mounted with HET diffuser with minimum system lumen efficacy of 120lm/W and system lumen of 4800 lm with CRCA Housing and with P.F.>0.95,THD<10%,CCT 5700 K/4000L, internal surge protection 2.5KV with input voltage range of 150V-270V,CRI 80, UGR<22.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70 ..Make Philips/Wipro/Trilux.

Supply of backlit non slim surface led downlighter in 12 W +/- 1 W in Round Shape with with minimum system lumen efficacy of 120 lm/W and minimum system lumens 1440 lumen with Pressure Die cast Aluminium heat sink with and HET diffuser and polycarbonate mounting box P.F.>0.95 ,THD<10% ,CCT 5700K/4000K, CRI 80, UGR<23,IP20 protection.The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2.5kV inbuilt in Driver .Make Philips/Wipro/Trilux.

Supply of backlit non slim surface led downlighter in 15 W +/- 1 W in Round Shape with with minimum system lumen efficacy of 120 lm/W and minimum system lumens 1800 lumen with Pressure Die cast Aluminium heat sink with and HET diffuser and polycarbonate mounting box P.F.>0.95 ,THD<10% ,CCT 5700K/4000K, CRI 80, UGR<23,IP20 protection.The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2.5kV inbuilt in Driver .Make Philips/Wipro/Trilux,

Supply of 40 W Round Hollow ring shaped suspended fixture having Housing made up of extruded Aluminum powder coated White/Black Housing with 100lm/W ,THD<10%,PF>=0.95, IP20 Protection, CRI 80 and CCT of 4000K/5700K with High efficiency, non-yellowing PMMA diffuser having dia of 800 mm. The LEDs have minimum life of 50000 hrs at L70 and have Surge prortection of 2.5 KV. Make Philips/Wipro/Trilux.

Supply of surface/Suspension mounted cylindrical shape COB LED downlighter 20W +/- 1W Fixture having inset clear glass diffuser with extruded aluminium black housing having system lumen efficacy of 80 lm/W with P.F.>0.95 and THD<10% with beam angle 36 degree .The LEDs with minimum life of 50000 Hrs. The LEDs used in the luminaire shall have CCT of ANSI Bin 4000 K and CRI of minimum 80. Make: Philips, Wipro, Trilux.

Supply of 25 W+/-1W hexagonal shaped suspended fixture having Housing made up of extruded Aluminum powder coated White/Black Housing with minimum system lumen efficacy of 125lm/W ,THD<10%, PF>=0.95, IP20 Protection, CRI 80 and CCT of 4000K/5700K with Hexagonal shaped Full HET Plastic Diffuser having dia of 600 mm The LEDs with minimum life of 50000 Hrs and have Surge prortection of 2.5 KV. Make Philips/Wipro/Trilux.

Supply of Led fixture 600mmX600mm 33 W+/- 1W Suspension Mounted Fixture having system efficacy of minimum 95lm/W Light Light engine and diffuser only on the edges and hollow in between with Drop Down HET PMMA diffuser. Fixture having minimum system lumen efficacy of 95lm/W with extruded aluminium housing with P.F.>0.95 with THD<10% ,CRI 80,CCT 5700 K/4000K .The LED with Useful life of 50000 Hrs at L70. Make: Philips, Wipro, Trilux.

Supply of following Ceiling Fan : 1200mm Sweep similar to Havells CAT no. - samart /RR Kabil

Supplying of Heavy Duty Exhaust Fans 300 mm, 1400 RPM

Supply of UL approved low carbon high tensile steel rod with copper coating of min 254 micron JK Chemrode - 0110 CBR the dia should be 25 mm with length of 10 feet ( 3000 mm) . The rod shall be as per IEC 62561-2 and approved by UL 467. The rod shall be tested from NABL lab for current discharge not less then 46kA peak. The Chemrode shall be surrounded with 25 kg ( 1 bag) of Earth enhance materiel JK Reslow according to IEC 62561-7 and the Chemical resistance value shall not increase more then 0.067 Ωm and same will be tested from NABL lab. along with earth pit chamber made up polyplastic. Size of -254x330x260 MM (Model similar to PPC01)

SITC of Vertical Electrolytic Copper Lighting Arrester of 16 mm dia, 1000 mm long with Gun Metal base plate . Model similar to APSAT116C+APSTB16-253

SITC 8 mm round aluminium conductor for horizontal lightning protection - run in roof. Model similar to AL8.

SITC of roof conductor holder for 8 mm round aluminium conductor made of Gun Metal for horizontal installation. The distance between each holder should be min of 1 mtr. Model similar to APSRCS50.

SITC of T connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model similar to APSTCRC50

SITC of Cross connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model similar to APSCCRC50

SITC of straight connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model similar to APSPCRC50

SITC of Expansion piece to compensate the expansion of round 8 mm Al conductor when temperature variation . Connection should be in every 20 mtr. Model similar to APSEXP50

EXPANSION PIECE CONNECTOR-

SITC of 8 mm round aluminium conductor as a down conductor mounted in the surface of wall which will carry the lightning current to earth pit. Model similar to AL8.

SITC of Down conductor holder for 8 mm round aluminium conductor of min distance between the wall to the conductor will be of 85 mm. The distance between each holder should be min of 1 mtr. Model similar to APSRCS50

Supply and installation of Test Clamp to disconnect the down conductor from the earth termination network for regular checks of the earth termination resistance value.

SITC of 6 digit lightning strike counter. Model similar to LEC06

Supplying and laying 25 mm x 5mm G.I. strip on surface or in recess for connection etc as required.

Providing and laying of G.I. tape 32 mm x 6 mm from earth electrode directly in ground as required.

SITC OF SF6 insulated, 11kV Extensible Compact VCB (type VCE) contained within a metal clad enclosure having degree of protection to IP-54, suitable for outdoor use, free standing and comprising, Annexure –A BILL OF MATERIAL FOR HT Switch Board: 1 – 630 Amp triple pole, vacuum circuit breaker with independent manually charged spring mechanism and fully rated earth switch with provision for earth of the cable. 1 - Air insulated cable box with gland plate suitable for a bottom entry 3 core cables up to 300 sq. mm. The unit will be complete with: 1 - Mimic diagram on front panel complete with status indicators 1 - Set of positive standard mechanical interlocks 1 - Set of current transformers for protective relays with ratio 100-50/1A 1 - Self powered relay: Ashida/Equivalent Reputed make 1 - Set of VPIS for Circuit breaker 1 - External stud for earthing connections 1 - SF6 gas pressure indicator and SF6 recharging facility 1 - Local ‘PULL TO TRIP’ mechanism for each breaker. 1 - Set of auxiliary terminals 1 - Operating handle MAKE :-LUCY / ABB

1 No.3 phase 50 Hz 630 kVA, 11KV /415V, DYn11, core type double wound with copper conductor oil immersed ONAN cooled Distribution Transformer ON LOAD Tap changer voltage ratio of 11 KV / 415V with HT & LT Cable Box. Tappings +5% to –15% in steps of 1.25% shall be provided at line end of HV winding. .Losses are as per IS -1180 Level 1 (New Ammendment)) Capacity 630 KVA Input terminals suitable for connecting 11KV XLPE aluminium conductor armoured cable enclosed in a cable box. Output terminals suitable for connecting 1.1 KV grade single core aluminium conductor cable enclosed in a cable Box. L.T. Aux. terminals connections - suitable for 1.1 KV grade PVC /XLPE cable on Transformer Part H.T.Aux. terminals – suitable for 11 KV grade XLPE Al. Cable on Transformer Part Output : 415 V +/- 1% , 3 phase 50 Hz ,Unbalanced load Winding temperature indicator with alarm and trip Contacts Pressure release valve / explosion vent to be provided on ther top of the tank. Silica gel breather Oil Temp. Indicator with alarm & trip Contacts

Supply, Erection, Testing and commissioning of indoor type cubicle pattern LT Switch-Board415 V or as called for in individual items, openable in front and back suitable for 3 phase, 4 wire, 50Hz AC supply at an ambient temperature of 45 C. The cubicle should be dust proof, vermin proof, well ventilated and enclosure protection shall be IP-54 as per IS 2147-1962.or as per CPWD specifications, ( Part IV - Sub-station) and IS: 8623 The cubicle should be front operated, floor mounted, free standing with compartments in tier formation, extensible on both sides. The panel to be provided with PVC Sleeved TPN Electrolytic Al. Bus Bar and PVC insulated solid interconnections and also provided with 50x6mm. horizontal tinned copper Earth Bus Bars in each section. UPS Panel. 2 nos. 100A FP by-pass Switch 2 Nos. 100Amps TP+2N ,MCCB with Microprocessor Release adjustable with rotary handle 3 set Phase Indicating LED BUSBAR :- 300 Amps 4 pole aluminum conductor ( CD 0.8A /sq.mm. ) bus bar (PVC sleeve Heat-shrinkable busbar insulation) supported by DMC / FRP insulator (MAIN BUSBAR) OUTGOING 6 Nos. 63Amps FP ,MCB for Spare 6 Nos. 40Amps FP ,MCB 1 No. Type C SPD with indication and fuse. complete panel as above

Fabrication supply, installing,testing & commission and connecting with main LT Panel of indoor type dust and vermin proof hinged and lockable doors at back side made out of 14 SWG CRCA MS Sheet including painting and complete with interconnections, Top entry, cable glands,removable gland plate, plugs, bonding to earth with 2 independent earth connections having 2 nos 25x6mm GI strip at bottom of panel as earth bus ,the construction of panel shall be compartmentalised, very compact, easy in maintenance .provision of ventilation shall be through axial flow fans system Legend plate of suitable size of showing panel no. and name of panel for outgoing feeder and as per the following and as per drawing for Floor Panel complete panel as above

Fabrication supply, installing,testing & commission and connecting with main LT Panel of indoor type dust and vermin proof hinged and lockable doors at back side made out of 14 SWG CRCA MS Sheet including painting and complete with interconnections, Top entry, cable glands,removable gland plate, plugs, bonding to earth with 2 independent earth connections having 2 nos 25x6mm GI strip at bottom of panel as earth bus ,the construction of panel shall be compartmentalised, very compact, easy in maintenance .provision of ventilation shall be through axial flow fans system Legend plate of suitable size of showing panel no. and name of panel for outgoing feeder and as per the following and as per drawing for Ventilation Panel INCOMER:- 1 Nos. 400Amps FP ATS 1 Nos. 400Amps FP ,MCCB with Thermal Magnetic Release adjustable with rotary handle from Rising Main 1 set Phase Indicating LED 1 Nos Multifinction Meter With RS-485 port 1 sets Current Transformer 250/5A, Cl-1.0, 15VA 6 Nos. Control MCB BUSBAR :- 500 Amps 4 pole aluminum conductor ( CD 0.8A /sq.mm. ) bus bar (PVC sleeve Heat-shrinkable busbar insulation) supported by DMC / FRP insulator (MAIN BUSBAR) OUTGOING 8 Nos. 80Amps FP ,MCCB with Thermal Magnetic Release adjustable with rotary handle 1 Nos. 63Amps FP ,MCB 1 Nos. 40Amps FP ,MCB 1 No. Type C SPD with indication and fuse. complete panel as above

Design, Manufacture, Supply, Installation, Testing and Commissioning of Panel Fabricated out of 16 SWG CRCA sheet steel, IP 54, wall / floor mounting type with rain canopy The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid. In case of Fire Panel INCOMER:- 1 Nos. 500Amps FP ,MCCB with Thermal Magnetic Release adjustable with rotary handle 1 Nos. 500Amps FP Contactor 1 set Phase Indicating LED 1 Nos Multifinction Meter With RS-485 port 1 sets Current Transformer 250/5A, Cl-1.0, 15VA 6 Nos. Control MCB BUSBAR :- 600 Amps 4 pole aluminum conductor ( CD 0.8A /sq.mm. ) bus bar (PVC sleeve Heat-shrinkable busbar insulation) supported by DMC / FRP insulator (MAIN BUSBAR) OUTGOING 1 Nos. 400Amps FP ,MCCB with Thermal Magnetic Release adjustable with rotary handle 5 Nos. 63Amps FP ,MCCB with Thermal Magnetic Release adjustable with rotary handle 1 Nos. 40Amps FP ,MCB 1 No. Type C SPD with indication and fuse. complete panel as above

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 4Cx10

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 4Cx16

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 4Cx25

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx35

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx50

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx70

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx95

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx120

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx150

Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5Cx185

Supply and Laying of heavy duty copper armored cables 1.1 KV grade including necessary support clamps at ceiling level and connection legs,glands etc complete in all respects. Control cable 10 core 2.5 Sq.mm

Supply & Testing of following 11 KV( UE) grade multicore Aluminium conductor XLPE insulated cable, insulation screening with extruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required. 3 C x 70 Sq. mm 11 KV (E) H V CABLE LAYING

Supplying and fixing integral post top lantern with 30 watt LED fitting comprises of copper dust finish cast aluminium spigot and spun aluminium canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting, open construction driver and accessories are wired up to terminal block. LED of 1 to 3 W each assembled on single MCPCB, having color temp 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF 0.95 & surge protection 2KV.The colour rendering index of LED light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer.similar to MF PTL LED 656 / oriant

Supply , Installation, Testing & Commissioning of street light 60 W LED with complete with pot optic reflector including connection with 3x2.5sq.mm single core PVC insulated copper conductor cable from junction box to fixture as required

Supply , Installation, Testing & Commissioning of flood light 90 W LED with complete with pot optic reflector including connection with 3x2.5sq.mm single core PVC insulated copper conductor cable from junction box to fixture as required similar to MF FL LED 401 (EC) / Oriant

Supply, Installation, Testing and Commissioning of 202x238x111 (KVPC) Polycarbonate thermoplastics enclosure - junction box with I.P - 65 Protection with cable hinged cover of approved design complete having gasket of internally embedded & made of polyeutherene & should be weather proof, rust proof, dust proof, water proof - box shall be tested as per IEC - 60670-2/60670-22. the box shall have self threaded holes & provision for mounting din rail. with 2 Nos cable gland including supplying & fixing crimping 2 nos lugs & 1 nos 32A connector 6 way for looping the incoming & outgoing cables and also connection of the street light one 6A SP MCB Including Connection of 2x6 sqmm Cable etc as Required

Supplying of 8 mtr long hot dip Galvanized octagonal Pole with top of the pole 70 mm dia (A/F) and bottom of the pole 135 mm dia (A/F) made out of 3mm sheet with MS base plate of size 225mm (NS) x 225mm (NS) x 16mm (NS) on precast RCC foundation complete with suitable size opening inside the pole with flush weather proof door with locking facility preferably with LN key having proper arrangement with Accommodating of 1 Nos. 6 Amp.,10 KA MCB & neutral link 4 way connector suitable for 25 Sqmm cable complete with electrically safe including inside cable termination with thimbles i/c wiring from pole box to fitting with 3x1.5 sq.mm. FRLS PVC insulated copper conductor wire, earth connection, din channel, earth stud and other accessories pertaining to this pole (But without street light fitting) etc as reqd.including providing & laying in position suitable RCC foundation as required for 6 mtr. octagonal hot dip Galvanized Pole as per Manufacturers drawing with 1:1.5:3 concrete (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) including excavation of all kind of earth such as all type of soil/soft rock or hard rock etc. as per existing site condition i/c providing, cutting, bending and placing reinforcement & J type foundation bolts , anchor plate and templates in position as per manufacturer Standard and Providing PVC Pipe for Cable Entry and Exits Including Disposal of Surplus Malba / Softrock / Hardrock Stone etc.as Required.

Transportation of suitable truck mounted drilling machine with all necessary accessories connectiing T&P required for drilling and correction of including leveling etc. complete with all respect as per direction of the Engineer in charge.

Drilling of bore size attachment required drilling in alluvial, bolder, pobbles gravels, Rocky stone sticky clay etc. Inlucind cost of attachment consuble store bits, water pole etc. Complete 175 caseing pipe which will welded together using 2.5 or 3.25 mm diaadvani Oerlinkon cletrodes with plain end and the other end champhered to 50 degree removing pint in the area to be welded inclusive on the cost of bio chargeable and non toxix from flush etc. Complete with all repects as per direction of the Engineer in charge.

Supply of 175 mm dia thick MS ERW casing pipe from approved manufacters complete with all repects confirming IS 4270

Development of tubewell by air compressor.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Development of tubewell by OP Unit 200 mm dia

Supply and fixing of 175 mm dia size M.S. tubewell cap.200 mm clamp

Supply of submersible pump set having discharge 100 LPM of 120 mtr. Head 3 Phase 415V+10% 50 C/s with motor complete in all respects.

Supply of starter cum panel suitable for operation on 3 Phase 415 volts, 50c/s suitable capacity starter cum panel with over and under voltage protection, Ameter, Voltmeter & Phase Indicator complete in all respect.

Supply of 6 sq.mm three core submersible cable for above pumping plant.

Supply & Laying of 16 sq mm al armoured 4 core cable.

Supply and fixing Main Piping and valves as Follows Supply of 50 mm dia 3 mtr. Long MS column pipe assembly both side threaded with socket-120 mtr. Supply of 50 mm size CIDF sluice valve 2 Nos. Supply of 50 mm size CIDF reflux valve-1 Nos spanner set, screw driver, plier, hammer, pipe rinch, screw rinch-01 set Venture (50 x 75) 1 No. Supply of 50 mm size CIDF Redial TEE-1 No Supply of 50 mm size to pump outlet dia reducer and other end flanged 1 no. Supply of heavy duty MSDI clamp Supply of Tubewell cap 1 no Supply of 50 mm size CIDF 90 bend-I No. Nuts Bolts, Rubber/ Fiber packing for jointing above pipers & special-I set Supply of 100 mm dia pressure gauge with control cock & fitting of range 0.20 kg/cm with complete with all fitting 01 set Supply of Tool kit having DE spanner set, ring

Installtion, Testing & Commissioning of pumping Plant with lowering of column pipe and fixing of valve and accessories.

Earthing with G.I. Earth Plate of suitable size including accessories and providing masonary enclusure with cover plate having locking arrangement and watering pipe with charcoal/coke and salt as required with supplying and laying of 25mm x 3 mm G.I. strip inlucding connection/terminating with nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 sets of brass nut bolt& spring washer spaced at 50 mm) as required-2 set.

Testing of pumping plant at site.

Painting of entire installation with two coats of super enamel paint as per direction of Engineer in charge.

Geiological & Hydrological survey.

Testing of Water sample

Cost of Running Maintance for 06 month.