Construction of Tezpur Chowk bazar at tezpur under CIDF

Amount

Civil works

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to PL 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, griders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform.

Columns, pillars, piers, abutments, posts and struts

Stairs, (excluding landings), except spiral staircase

Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size de rived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse agg. and fine agg. derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth LVL.Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth & up to floor V level.; Concrete of M30 grade with minimum cement content of 350kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse agg. and fine agg. derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

12 mm cement plaster finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

12 mm cement plaster finished with a floating coat of neat cement of mix :1:3 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand).

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).

Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints

Providing and fixing sheet covering over expansion joints with iron screws as per design.Aluminium fluted strips 3.15 mm thick.200 mm wide

Providing and filling in position, blown bitumen in expansion joints.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content/ With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.M/S Flat

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with local sand, with common burnt clay non modular bricks.

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm. 11.41A.3 - Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08%and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymermodified quick-set tile adhesive (Water based) conforming to IS: 15477,in average 3mm thickness

8.31:- Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Second class teak wood

9.147D:- Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Float glass panes-5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :125x85x5.5 mm (heavy type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete.250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete:125mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Providing and fixing bright finished brass door latch with necessary screws etc. complete. 300x16x5 mm

Item no.7/22.5:- Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto PL Thermo-Mechanically Treated bars of grade Fe-500D or more.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters

Providing and fixing ball bearing for rolling shutters

Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture.

Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture.

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).

Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineerin- charge.

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead.Of sectional area 40 square centimetres and above

Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:G.S. Sheet

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to PL 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete

Boring

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all comp. as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.All Types of Soil___300mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.100 mm nominal size dia metre

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia having minimum wall thickness 5.00 mm

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150MM dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150 mm clamp each

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150mm dia

Supplying, fitting, fixing of Panel board of 2HP complete as dircted by the department.

Supplying, fitting, fixing of Cable Rope for submersible pump complete as directed by the department.

Supplying, fitting, fixing of Submersible Cable (Electric wire) for submersible pump complete as directed by the department.

Supplying, fitting, fixing of Submersible Pump 2 HP complete as directed by the department.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Sanitary Works

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required :Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern

Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Cast Iron Floor Trap

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. (For PWD)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.(For PWD)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps(For PWD)

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material bymechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge

Providing,running & maintenance of 1 vehicle on monthlu basis new in good and running condition,viz. bolero,scorpio etc for total run upto 3000 km in a month.All necessary taxes for operating the vehicle should be fully paid and all necessary papers shall be provided in the vehicle as required in the motor vehicle act.The vehicle shall be available 12 hours as required by engineers in charge for all days including Sundays & Holidays.The drivers should possess valid driving license.The agency shall bear all the expenses in keeping the vehicle in smooth running condition such as fuel,lubrication oil etc & necessaryincluding Salary for the driver to be borne by the agency

PLUMBING/PHE

Providing, fixing, testing and commissioning in position SWR PVC PIPE TYPE-B(4Kg/cm2.) ring fit pipe conforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offsets, cowl, access pieces/plugs, including all vertical and horizontal heavy duty MS pipe supports & clamps, wall etc. jointing with PVC Adhesive joints including cutting holes in walls and making good the same with necessary fittings as per direction of Engineer in Charge. (Make: Ashirvad/ Supreme/ Astral Makes) Type 'A' , Solvent cement joint inside toile 75 mm OD

160mm OD External rain water pipe

Vertical piping with Rubber Ring joint 75 mm OD

Providing & fixing in position Multi Inlet PVC floor traps for thr following depth of self cleansing design with outlet size of 75mm diameter of approved make, Including making connection with PVC soil/waste pipes using rubber gaskets, embeding the trap in 150 mm thick PCC 1:2:4 etc., complete all as specified & directed. (Make: Ashirvad/ Supreme/ Astral Makes) 175mm deep PVC floor traps-In Toilets

Providing, fixing, testing and commissioning in position SWR PVC PIPE TYPE-A ring fit pipe conforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offsets, access pieces/plugs, including all vertical and horizontal heavy duty MS pipe supports & clamps, wall etc. jointing rubber ring including cutting holes in walls and making good the same with necessary fittings as per direction of Engineer in Charge. (Make: Ashirvad/ Supreme/ Astral Makes) 75 mm OD

Providing and fixing in position Side wall parapet grating made of CI body with Aluminium grate and four SS screws to fit for inlet of rain water pipes at terrace level in CM 1:2, including making bores in the roof, setting in position and forming smooth rain water inlet gutter to direct rain water into the rain water pipe etc., complete all as specified and directed. For terrace rain water. (Make: Near Aco neco) 75mm outlet.

160mm outlet.

Supply, installation, testing & commissioning of Submersible type drain sump pump having CI casing & SS impeller. The scope shall also include necessary PVC piping with delivery isolation valve & NRV with starter panel, float switch for auto pump operation,etc. complete. for OHT transfer aplications ( Domestic & flushing). (Make :- Shakthi, Lubi, Kirloskar or equivalent) 2.8lps at 30m head (1 working + 1 standby)

1.4lps at 30m head (1 working + 1 standby)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with S.S. tringular plate for Eureopean type W.C.

C.P. brass toilet paper holder of standard size

C.P. Brass angle valve 15 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

40 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal dia Pipes

65 mm nominal dia Pipes

80 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 65 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 65 mm nominal bore Vertical

80 mm nominal bore Vertical

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With Sewer bricks conforming to IS : 4885

ELECTRICAL

Wiring, Light Fixtures, Fans, Exhaust Fans Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium class PVC conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.. Group C Note: The average length of the conduit and wire exceeding the standard length indicated in Group C shall be paid at running meter basis under conduit(Item code:1.36 to 1.38) and wires(Item code:1.3) line item

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C Note: The average length of the conduit and wire exceeding the standard length indicated in Group C shall be paid at running meter basis under conduit(S.No:1.15 to 1.17) and wires(S.No:1.3) line item

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit ( Thickness not less than 2mm) as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

MCB CONTROLLED POINT:- Wiring for the following light points with 2.5 sq.mm PVC insulated FRLS copper conductor 1100 volts grade stranded flexible wires of approved make in surface/concealed 25 mm dia PVC conduit controlled by SP MCB provided in the DB and earthing the point with 2.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. (Cost of MCB not to be included) Primary Points ( up to 8mt. Length)

Loop Points ( up to 5mt. Length)

6-10 lights controlled by a MCB (Avg length 60 meters)

11-12 lights controlled by a MCB (Avg length 80 meters)

Supplying and fixing of following sizes of Medium class PVC conduit along with accesories in concealed manner including cutting the wall and making good the same in case of recessed conduit As required. (For Electrical & ELV Systems) 20 mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6A, multi socket outlet controlled by 2 no. 5/6A switch , connections etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch

3 pin 5/6 A socket outlet

Supplying and fixing following size modules , GI Box along with modular base and cover plate for modular switches in recess etc as required. 3 module (100mmx75mm)

4 module (125mmx75mm)

8 module (125mmx125mm)

12 module (200mmx150mm)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply and fixing of metal fan hook box of 10 mm M.S. round bar , bounded to to RCC bar up to 50 mm length each side & pierced through a 16 SWG thick MS bowl 100 mm dia , depth up to 75 mm , complete erected in position . With one coat of red oxide paint and 2 coats of synthetic paint .

DISTRIBUTION MCCB, MCB & DB Supplying and fixing following way, single pole and neutral, sheet steel, pre wired MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way, double door

6 way, double door

8 way, double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, pre wired MCB distribution board 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 Way( 4+18) TPN DB, Double door

8 Way( 4+24) TPN DB, Double door

MCB Supplying and fixing, Single pole 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating,Double pole 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40A Four Pole MCB rating, 415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

RCCB Supplying and Fixing 25 DP RCCB (30mA) 10KA in the existing MCB DB complete etc as required.

Supplying and Fixing 40 DP RCCB (30mA) 10KA in the existing MCB DB complete etc as required.

CABLE TRAY ARRANGEMENT Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thicknes

600 mm width X 75 mm depth X 2.0 mm thickness

EARTHING Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 40 x 6 mm strip GI on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing & fixing of Earthing with GI earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosure with coverplate having locking arrangement and watering pipe of 2.7 mtrs long etc with charcoal / coke and salt as required

Earthing with copper earth plate 600 mm X 600 mm X 3.0 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Supply and laying of following 1100 volts grade FRLS PVC insulated copper conductor wire including copper thimbles, fixing hardware as required. Single core 4sq.mm Green colour Rates shall also include the following : All fixing accessories such as brass saddles, brass screws raw plugs etc. Jointing by rivetting and brazing after rivetting in case of copper and welding / bolting in case of GI earthing. Cutting chases holes and making good the same wherever required. Effecting adequate and proper interconnections. Use of copper thimbles. Earthing system shall comply to IS:3043-1987. All earthing pits shall be interconnected.

Supply, loading, transportation unloading and storages at site , shifting from storage place to site of following sizes of XLPE insulated PVC sheathed, FRLS, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS amended upto date and as per specifications.All cables shall be tagged. 50 Sq.mm x 3.5C Al. Cable

70 Sq.mm x 3.5C Al. Cable

95 Sq.mm x 3.5C Al. Cable

240 Sq.mm x 3.5 Core Al. Cable

Supply, loading, transportation unloading and storages at site , shifting from storage place to site of following sizes of XLPE insulated PVC sheathed, FRLS, Copper conductor armoured power cable of 1.1 KV grade conforming to IS amended upto date and as per specifications.All cables shall be tagged. 10 Sq.mm x 4 Core CU. Cable

MV cable laying in existing Hume Pipe :Laying of one number PVC insulated XLPE insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. Above 185 sq.mm and up to 400 sq. mm

Laying and Fixing of one no. PVC insulated and PVC sheathed /xlpe power cable of 1.1 grade of following size on cable tray as required Above 35 sq.mm up to 95 sq.mm ( clamped with 25x3mm MS flat clamp)

Above 185 sq.mm up to 400 sq.mm ((clamped with 40x3mm MS flat clamp)

MV CABLE TERMINATIONS Supplying and making end termination with brass compression gland and Aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5c 50 Sqmm

3.5c 70 Sqmm

3.5c 95 Sqmm

3.5c 240 Sqmm

Supplying and making indoor end termination with brass double compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 4c 10 sqmm

Supplying,Installation, testing and commissioning of cubical type LT panel suitable for 415V, 3 Phase,4 wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing completed 7 tank process of powder coating in approved shade,DMC/SMC bus bar supports,with short circuit withstand capacity for 1 sec, bottom base channel of MS section not less that 100 mm x 50mm x 5mm thick, fabrication shall be done transportable sections,entire panel shall have a common copper earth bar of size 25mmx5mm at the rear with 2 no's earth stud,solid connections from main bus bar to switchgears with required size of alunimium bus bars and control wiring PVC insulated copper conductor S/C cable alleys,cable gland plates in two half,i/c providing following switch gears: (with all necessary hardware, accessories as required for complete installation as per specifications and single line digram).The fault level indicated in panel is the minimum requirement. However vendor should consider the fault level at components/busbar as follows, Upto 250A- 25kA, 250A to 400A-36kA, above 400A - 50kA. All MCBs fault level should be 10kA. All RYB indication lamps including voltmeter shall be protected with 2A control MCB. The busbar rating indicated is the final rating after considering the derating factor. All multifunction meters shall be provided with RS485 Port. Size of the MFM shall be 96mmx96mm. THE PANELS SPEC SHALL BE AS PER SLD DWG NO: CB-ELE-SLD-01 MAIN LT PANEL-1

UTILITY PANEL

GF FEEDER PANEL-1,2,3,4

1F,2F FEEDER PANEL-1,2,3,4

MISCELLANEOUS & PROTECTIVE DEVICES Supply and fixing in position the approved “Shock Treatment Charts” written in English and Local Language. These charts shall be framed in teak wood frame and covered with glass of approved shape and size as specified by Local Electricity Authorities written in English & Local Languages.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply and fixing in position the approved single line diagram in paper framed in 1000 x 800 mm size glass frame in the sub station.

The first aid kit should be identified with the ISO graphical symbol for first aid (from ISO 7010) which is an equal white cross on a green background. It can be assembled in almost any type of container. Standard kits often come in durabel plastic boxes, fabric pouches on in wall mounted cabinets. It is recommended that all kits are in a clean, waterproof container to keep the contents safe and aseptic. The kits should also be checked for any damage to the contents or expiry..

Supply and providing ISI marked electrical 1.1 kV grade 3 mm thick anti-skid rubber mat as per IS:15652-2006 with up to date ammendment.

Providing pair of rubber hand gloves suitable for working on 1.1KV supply.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supply Installation,Testing & Commissioning of Fire Extinguisher

LIGHTING FIXTURES Supply, Installation, Testing and Commissioning of LED Luminairewith aluminium extruded profile finished in white powder coating, snap fit high translucent frosted PMMA diffuser and high reflective aluminium reflector complete with electronic driver, Power factor ≥ 0.95, THD ≤ 10%, rated life of L-70@50000 hrs with system lumen output ≥ lumen and system luminious efficacy ≥ 95lm/W. The Luminaire shall have a CRI ≥ 80 Surface mounted circular 18W LED light fixture Model number : LCDSPLN-R-18-CDL of make CROMPTON or equivalent

Supply, Installation, Testing and Commissioning of LED Luminairewith aluminium extruded profile finished in white powder coating, snap fit high translucent frosted PMMA diffuser and high reflective aluminium reflector complete with electronic driver, Power factor ≥ 0.95, THD ≤ 10%, rated life of L-70@50000 hrs with system lumen output ≥ lumen and system luminious efficacy ≥ 95lm/W. The Luminaire shall have a CRI ≥ 80 recessed square dounlighter LED Light fixture 9W. Model number : LD80-530-XXX-60-XX / LD81 of make Wipro or equivalent

Supply, Installation, Testing and Commissioning of 1x10W LED Mirror light fixture. Model number : BN021C LED10SPSU CDL GR of make Philips or equivalent

Supply, Installation, Testing and Commissioning of 1x18W LED 4 feet Batten light fixture. Model number : LL20-221-XXX-65-NE of make Wipro or equivalent

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV Grade Solid Aluminium conductor stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour, extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable including connection etc. as specified and directed by the deptt. a.6.00 Sq.mm 2 Core Aluminiumarmoured U.G. cable.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (But without charcoal/ coke and salt ) as required.

Supplying, installation, testing and commissioning of the following flood light of LED luminaries complete with all accessories as required complete with necessary support with 2.5 sq.mm. P.V.C. insulated S.C. copper conductor as required and as directed by the department. Khaitan make 100 Watt LED Luminaries for Flood Light.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

SITC of 300/305 mm Sweep Exhaust Fan (Make- Usha model- Aeroclean)

Supplying of 1200 mm sweep anti dust decorative fan with air delivery not less than 240 cum / minute and speed not less than 380 rpm suitable for 230 V, 50 Hz single phase AC supply or at low voltage etc. completed as required.

SUPPLY INSTALLATION ,TESTING& COMMISSIONING OF 62.5 KVA DG Supply Installation,Testing & Commissioning of 62.5 KVA DG(Annexure-I)

Supply, loading, transportation unloading and storages at site , shifting from storage place to site of following sizes of XLPE insulated PVC sheathed, FRLS, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS amended upto date and as per specifications.All cables shall be tagged. 50 Sq.mm x 3.5C Al. Cable

Supplying and making end termination with brass compression gland and Aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5c 50 Sqmm

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing & fixing of Earthing with GI earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosure with coverplate having locking arrangement and watering pipe of 2.7 mtrs long etc with charcoal / coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3.0 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Cost of DG Pad & Shed(As Per Annexure-II)

UMTANG TIMUNG