Up-gradation of RHWE/Girls Hostel at RHR-TS Seobagh, Distt. Kullu (SH- Civil work)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil complete in all leads, lifts and carriage of material as directed by the Engineer-in-Charge. a). Ordinary rock.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m etc. complete in all respect as per satisfaction of Engineer-in-Charge. a).All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level complete in all respect as per satisfaction of Engineer-in-Charge.

a) 1:5:10 (one Cement : five sand : ten graded stone aggregate 40 mm (twenty milimetre) nominal size

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil etc. complete in all respect as per satisfaction of Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one & half coarse sand : three graded stone aggregate 20 mm(twenty milimetre) nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Suspended floors, roofs, landings, balconies and access platform.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement: 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Cold twisted bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick edging 7 cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (one cement : four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Second class teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : a). 4 mm thick glass pane (weight not less than 10 kg per sqm).

Providing and fixing 35 mm thick Second class teak wood glaged shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked MS pressed butt hinges bright finished of required size with necessary screws etc.complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

b). 25 mm thick( for cup board) including ISI marked nickel plated bright finished MS piano hinges with necessary screws

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) 20 mm dia (heavy type)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge. (a). Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 200x10 mm(two hundred into ten milimetre)

b). 150x10mm(one hundred fifty into ten milimetre)

c). 100x10mm(one hundred into ten milimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a)150 mm

Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm (one hundred fifty milimetre)

40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and laying antiskid vitrified floor tiles full body in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, (Kazaria/ Nitco/ Orient bell make), in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete complete in all respect as per satisfaction of Engineer-in-Charge. a). Size of tile 600x600mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge. a)25 mm thick (twenty five milimetre)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (one cement: three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles (Kazaria / Nitco / Oreintbell make) conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dado over 12 mm thick bed of cement Mortar 1:3 (one cement: three sand) and jointing with grey cement slurry @ 3.3Kilogram per Square Metre including pointing in white cement mixed with pigment of matching shade etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a). Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. (a) Single socketed pipes 110 mm(one hundred ten milimetre) diameter

Providing and fixing on wall face unplasticised – PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Coupler 110 mm

20 mm cement plaster of mix:1:4 (1 cement: 4 sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade as required complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge. a)Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade with New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc. in all respect as per satisfaction of Engineer-in-Charge.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. a).With cement mortar 1:4 (one cement : four sand)

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in- Charge. a) For door/ window/ clerestory window

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x45 cm dry brick honey comb shaft with bricks and S.W.drain pipe 100 mm diameter, 1.8 m long complete as per standard design etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm PVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge. (Cera / Hindware make). a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge. (Cera/ Hindware make). a) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Cera/ Hindware make) (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 610x510 mm bowl depth 200mm

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms etc. complete in all respect as per satisfaction of Engineer-in-charge. a) 15 mm nominal bore(Seiko/Smile/Spartan Make)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) 100 mm diameter

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge.(Seiko/Smile/Spartan Make)

Providing and fixing 45 cm length and 15 mm nominal dia uplasticised PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a) 20 mm (twenty milimetre) nominal bore

b) 25 mm (twenty five milimetre) nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 Sintex marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto one metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge

Providing and fixing G.I. Pipes (medium grade) complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a)15 mm dia nominal bore.

b) 20 mm dia nominal bore

Providing and fixing G.I. pipes medium grade complete with G.I. fittings including trenching and refilling etc. complete in all respect as per satisfaction of Engineer-in-charge. (Jindal / Surya make) a). 15 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 25 to 40 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one & half coarse sand (zone- III) : three graded stone aggregate 20 mm(twenty milimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm(forty milimetre) nominal size), inside plastering 12 mm thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement :two coarse sand : four graded stone aggregate 20 mm(twenty milimetre) nominal size) finished with a floating coat of neat cement complete as per standard design complete in all respect as per satisfaction of Engineer-in-Charge. a). Inside size 900x800mm and 450mm deep including 450x610mm dia opening (medium duty) SFRC Man hole cover with frame. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing 32mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) including disposal of malba etc. complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm dia (Seventy five millimetre)

b). 110mm dia (One hundred ten millimetre)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in charge (Finolex/Kisan/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge(Finolex/Vectus/D-plast make).

a) 75mm dia

b) 110mm dia

Providing and fixing PVC size P or S trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make).a) 110mm dia

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing PVC floor trap with grating ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge.(Filolex / Kisan / D-Plast make). a) 110mmx75mm

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a)110mm dia.

Providing and fixing aluminuim hooks and eyes etc. complete in all respect as per satisfaction of Engineer-in-Charge. ) 150 mm.

Providing and fixing 100 x 100mm PVC gully trap with grating brick masonry chamber with water tight SFRC light duty cover with frame as per standard design etc. complete in all respect as per satisfaction of Engineer-in-charge.

Keshav ram

Ankush Bhardwaj