Illumination and Electrification work of Dandeshwar Temple near Shree Jageshwar Dham, Almora

Amount

Supply installation, testing & ommissioning of LT panel suitable for 415 V, 3 phase 4 wire 50 Hz AC supply system, RYB LED indicators, VAF digital metering. Cable entry and outgoing are only with suitable sizes of screwless glands, including with all accessories copper bus bar, din rails, earth links, neutral links, glands, locks, connectors, operation complete with all respects. (as per the SLD attached no. LUC/D.D/SLD/T1A) Cubical : Supplying and erecting GI sheet 1.6 mm (16 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. Supplying and erecting bus bar chamber triple pole with neutral with four copper bars, 500V, 100A complete as per specification (1.)Supplying, erecting & marking FPMCCB micro-processor 100A B series in provided distribution board as per specification -1 Nos (2)Supplying, erecting & marking TPN MCB 6A to 32A, B series in provided distribution board as per specification -5 Nos (3)Supplying, erecting & marking SPN MCB 6A to 32A, B series (for lighting) in provided distribution board as per specification - 7 Nos (4)Supplying, installation & marking of surge arrestor / surge protection device at the main distribution board after the incoming breaker of type 1+2 tested for Imax 100 kA for three phase and neutral as per specification no. CP-SPD -1 Nos(5) Supplying, installation & marking of 100A ATS -1 Nos (6)Supplying & erecting single phase 2 wire system having in built astronomical adjustable programmable timer with minimum 5 years battery backup, 2 pole contactor upto 80 A, with maintenance mode to switch ON - 3 Nos

Supply,installation, testing and commissioning of the servo voltage stablizer of following ratings, 3-phase, Copper winding, 50HZ Frequency, Unbalanced input voltage and unbalanced load, Volt/ampere meter CT's, input voltage range- 360V-480V, output voltage range- 410-420V adjustable 30KVA

Supplying, erecting and commissioning of diesel generating set with alternator of 30 kVA output continuous rating, 3 phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 RPM with AMF Panel and approved by CPCB 4

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing the following rating, four pole, (three phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 40 A 4p

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A Isolator

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for the inductive load of following poles in the existing MCB DB complete with connections, testing and commissioninq etc. as required. Single pole

Supply, installation, testing and commissioning of the PC (Polycarbonate) Termination junction box (IP66), terminal with 2 clamping units per pole 5-pole per pole, 4 x 4 mm² r / f, included cable entry: 3 x ESM 40, sealing range Ø 17-30 mm with one cable entries M 32 from the rear side lid fasteners sealable without accessories external brackets for wall fixing included colour: grey, RAL 7035, rated insulation voltage Ui = 690 V a.c./d.c., in accordance with IEC 60670-22, Incoming - 1 no. 4 core 4.0/2.5 sq mm copper armoured cable Outgoing - 2 nos. 3 core 2.5/1.5 sq mm copper armoured cable. Built-in dimensions W 210 x H 155 x D 92 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Supply installation testing & commisioning of Empty box (IP66) with installation equipment on DIN rails or mounting plates (order separately) with opaque lid fastener for tool operation sealable box walls without knockouts external brackets for wall fixing included, colour: grey, RAL 7035, material: PC (polycarbonate) mounting plate, glands and complete with all required accessories and hardware to complete the job in all resepcts. Built in dimensions W 170 x H 220 x D 96 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Supply installation testing & commisioning of Empty box (IP66) with installation equipment on DIN rails or mounting plates (order separately) with opaque lid fastener for tool operation sealable box walls without knockouts external brackets for wall fixing included, colour: grey, RAL 7035, material: PC (polycarbonate) mounting plate, glands and complete with all required accessories and hardware to complete the job in all resepcts. built in dimensions W 215 x H 320 x D 106 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Providing & erecting steel perforated type cable tray manufactured from 16 swg (1.6 mm thick) Steel sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in the approved manner.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm dia.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm dia.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supply installation testing & commissioning of 6.0-meter height 75mm dia, C class MS pole, anthracite grey paint, with plate mounting arrangement, plate size 450mm X 450mm X 20mm suitable for bracketless direct lighting fixture installation.

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of the following size in the existing RCC/ HUME/ METAL/DWC pipe as required. Upto 35 sq. mm

Supply of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground/DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 3.5C x 25 Sq.mm. Aluminum XLPE armored cable

Supply, connection, testing and commissioning of heavy duty, medium voltage,XLPE (IS 7098 - PART-II) insulated, Stranded AL / Cu conductorArmoured / Flexible cables as per specification & IS. The cable shall have outer sheeth of XLPE and inner sheath of PVC with stranded AL conductor wherever specified. The cable shall be laid underground in excavated trench / prepared trench / hume pipes when laid outside the building. Cable shall be laid throught preapred trench / cable tray / duct / hume pipe / channel / floor trunks etc when laid inside the building as instructed by PMC/Site Incharge.The scope shall include:1) Supply of Cables.(With Non Returnable Drums)2) Delivery of the cables at site.3) Unloading at site store.4) Shifting of cable from site store to place of installation.5) Connection of cable with proper tagging as specified ni specifications.6) Supply & fixing of cable clamps, brackets, supports, route markers etc. where ever required to fix the cables safely.7) Earthing the glands and armouring with earthing clamp and jumper and also connecting to common earth bar.8) Testing of insulation and continuity of cable and submission of reports to the client's representative. 9) To prepare submission drawing and to take approval of consultant at each stage.10) To prepare & submit as-built drawing and handing over document to end user.11) Rate shall be inclusive of route markers at 15mtr intervals 12) Each run of cable to be tested with 1KV meggar13) Proper cables tags of Aluminium shall be made and feeder shall be written. 4C x 6 Sq.mm. CU XLPE armored cable

--- Do--- but size 4C x 4 Sq.mm. CU XLPE armored cable

--- Do--- but size 3C x 4 Sq.mm. CU XLPE armored cable

--- Do--- but size 3C x 2.5 Sq.mm. CU XLPE armored cable

Supply and Providing heavy duty double compression brass gland and lugs end terminations,IP 66 complete,SIBG type, for the cable specified under above item with Bi-metallic lugs using crimping tool, Insulation tape, Identification tags etc., including end termination and Earthing of Gland. 4C x 6 Sq.mm. CU XLPE armored cable

--- Do--- but size 4C x 4 Sq.mm. CU XLPE armored cable

--- Do--- but size 3C x 4 Sq.mm. CU XLPE armored cable

--- Do--- but size 3C x 2.5 Sq.mm. CU XLPE armored cable

--- Do--- but size 3.5C x 35 Sq.mm. Aluminum XLPE armored cable

DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

1000mm ±15% Linear LED 25W, 1500 lumens - 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 1000mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 25 watts, 1500 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

1000mm ±15% Linear LED 15W, 750 lumens- 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 1000mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 15 watts, 750 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

500mm ±15% Linear LED 8W, 450 lumens- 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 500mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 8 watts, 450 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

300mm ±15% Linear LED 8W, 450 lumens- 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 300mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 8 watts, 450 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Neon Flex LED 20W/M, 1200 lumen/M- RGBW: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, Neon flex light mouting climps (as per application). The power consumption should be 20 watts per meter, 1200 lumens per meter delivered, diffused, CCT-RGBW. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Ring Flex Washer LED 20W/M, 1200lumen/M- RGBW: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 1000mm dia ring flex light mouting climbs (as per application). The power consumption should be 20 watts per meter, 1200 lumens per meter delivered, diffused, CCT-RGBW. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 50W, 4000lumens- 3000K/4000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP66, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should be 50 watts, 4000 delivered lumens, 30° beam angle with a tolerance of ±15%, CCT-3000K/4000K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 100W- Blue color: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP66, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should be 100 watts, 40° beam angle with a tolerance of ±15%, CCT-Blue color. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

1000mm ±15% Linear LED 10W- 2700K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 1000mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 10 watts, 600 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, CCT-2700K. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC non dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Diya Bollard Flickring LED 10W- 2700K: Supply installation testing & commissioning of exterior-rated decorative floor mounted IP67 or better, 200mm high bollard, and mounting brackets/clamps (as per application). The power consumption should be flickering 10 watts, diffused, CCT 2700K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV, diffused tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integrated non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK08. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Decorative light LED 10W, 600lumen- 3000K: Supply installation testing & commissioning of exterior-rated decorative floor mounted IP66 or IP67, 450mm dia light, and mounting brackets/clamps (as per application). The power consumption should be 10 watts, 600 lumens delivered, diffused, CCT 3000K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV, diffused tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integrated non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are included. Minimum IK08. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 15W, 800lumens- 2700K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP66, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should be 15 watts, 800 delivered lumens, 8° beam angle with a tolerance of ±15%, CCT-2700K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

500mm ±15% Linear LED 25W, 1500lumens- RGBW: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or better, 500mm ±15% long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should be 25 watts, 1500 lumens delivered, 10 x 30° beam angle with a tolerance of ±15%, CCT-RGBW. The housing material should be extruded aluminum, a powder-coated finish, The luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses a clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote 24V DC dimmable (IP67) with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. The lifetime of the luminaire (L70 @ Ta-35deg C L80B10) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS-certified. This includes all the required hardware, DMX controller and software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Supply installation testing & commissioning of Full range environmental rated (IP55 or better) In Ground or Above ground Landscape PA/ Music loudspeaker with one downward firing 4.5" (114 mm) advanced composite environmental full-range driver. Domed port grille for clear, consistent sound quality, The Speaker shall have a rated impedance of 4 Ω and shall have a line voltage matching (step down) transformer with taps at 80 watts or better. The nominal dispersion of the loudspeaker shall be 360° horizontal and 50° vertical at least.

Supply installation testing & commissioning of OF12-Channel Mixing Console Max. 6 Mic / 12 Line Inputs (4 mono + 4 stereo). 2 GROUP Buses + 1 Stereo Bus. 2 AUX (incl. FX). D-PRE” mic preamps with an inverted Darlington circuit. 1-Knob compressors. High-grade effects: SPX with 24 programs. 24-bit / 192kHz 2in / 2out USB Audio functions. Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter. Includes Cubase AI DAW software download version. PAD switch on mono inputs. +48V phantom power XLR balanced outputs. Internal universal power supply for worldwide use.

Supply installation testing & commissioning of Dynamic cardioid microphone for speech and vocals with noiseless on/ off switch Cuts through high on-stage levels Clear reproduction with a high presence Consistent sound quality (varying distances, moving off-axis) Handles high sound pressure levels Isolates handling noise, hum compensating coil Excellent feedback rejection.

Supply installation testing & commissioning of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant.

Supply installation testing & commissioning of 2 core Twisted, shielded balanced Audio and control cable with 22AWG or better 7 strand annealed bare copper conductors, Semi-Rigid PVC insulation, Riser rated PVC jacket. UL 444, UL 13 CMR rated.

Supply installation testing & commissioning of Outdoor rated surface mounted powder coated aluminium alloy having wall thickness of minimum 3MM on all sides, with width limited to 140 MM or less & height limited to 60 MM or less, to house IP67 rated two light fixtures as per the BoQ, wiring management and IP68 GEL connectors for internal connections, and to withstand load of 20 MM to 50 MM thick stone on top, for walkover application. It should have proper end caps to cover and protect the wiring. as per detail drawing given.

Supply installation testing & commissioning of Outdoor rated floor recessed stainless steel as per IS-277, Powder Coated, and SS-202/304/316. Width 100mm, Height 50mm, this includes all types of hardware and accessories.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.120 mm dia (OD-120 mm & ID-103 mm nominal)

Supply, installation, testing and commissioning of UTP 4 pair Cat6 cable in existing surface/recessed PVC or steel conduit. Make : D-Link/Moles/AMP CAT6 4 Pair 23 AWG UTP cable ,.Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz. Construction: 4 twisted pairs separated by internal X shaped, 4 channel, polymer spine / full separator. Half shall not be accepted. cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 Conductor Solid bare Copper and Jacket FR PVC and UL approved CM rated cable and Outer jacket sheath of the cable shall be LSZH. Insulation :High Density Polyethylene ,Attenuation (< 17 db), Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR.Dielectric Strength of cable should be 1.0KV dc,Cable support Conductor Resistance < 9.38 Ω /100m,Capacitance Unbalance of cable should max 330pF/100m

SITC of 24-Port Gigabit Smart Managed PoE Switch 24 x 10/100/1000BASE-T PoE ports ; 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface ; 193 W PoE budget Network Security The LAN switch shall support IEEE 802.1x to allow dynamic, port-based security, providing user authentication. It shall support RADIUS authentication to enable centralized control of the switch and restrict unauthorized users from altering the configuration. It shall have built in mechanism to protect the switch against traffic flooding caused by virus attack VLAN The LAN switch shall have IEEE 802.1Q VLAN encapsulation. Up to 255 VLANs per switch. It shall have Management Vlan It shall have Asymmetric Vlan Performance The Switch shall have Non-blocking wire speed switch fabric , The Switch shall have Min. 56 Gbps Back plane or higher , The Switch shall support Min. 16K Mac address The Switch shall support Min. 256 VLANs , The Switch Should support Jumbo Frame (up to 9,216 Bytes) Approved Makes- CISCO / HP / SIEMENS / /D Link

Supply, installation, testing and commissioning of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm Approved Make : Shetiya/Anchor

Supply, Installation, Testing & Commissiong of IP BULLET CAMERA(Outdoor) Supply of 5MP IR Bullet camera with 1/2.9‑inch CMOS, Total sensor pixels 3072 (H) x 1728 (V); up to 25fps; Sensitivity – Measured according to IEC 62676 Part 5 (1/30, F1.6), Color 0.379 lx, Mono 0.042 lx, With IR 0.0 lx, 120dB WDR, H.265; H.264; M- JPEG, Automatic Electronic Shutter (AES); Intelligent Dynamic Noise Reduction, Intelligent Defog, Rule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), Privacy Masking, Pixel counter, Memory card slot, IR Range 30mtr, Automatic Varifocal 3.2 to 10 mm, Alarm Input 1/1, Audio Input/output, RJ45, G.711, Audio Streaming Full-duplex / half duplex, ONVIF Profile S, G & T, IP66, IK10, PoE, CE, FCC, UL certified. SD card support up to 2TB. FTP, Dropbox and e-mailapplications Approved Makes- Bosch/Axis/Pelco

Supply, Installation, Testing & Commissioning of 16-channel network video recorder (NVR), Real-time recording: Up to 16 channels 1080P @ 4Mbps, Operating System LINUX, H.265, H.264 high quality decoding, RAID-0/1/5/6/10 support, motion detection, 3 USB 2.0 ports, USB storage device, 2 RJ-45 port, 1 RS-232, Hot swap, 2 bay HDDs, Support ONVIF Profile S, HTTP/HTTPS, TCP/IP, RTSP, UDP, NTP, HTTPS, DHCP, IP Search protocols can support Approved Makes- Bosch/Axis/Pelco

Hard Drive Disk: SITC of Surveillance HDD 8 TB for 30 days storage at D1 resolution. Approved Makes- Seagate/WD

Supply, Installation, Testing and Commissioning of 55 Inch Professional LED Display , Size : 55 Inch diagonal , Brightness : 440 nits , 4K (3,840 x 2,160), Professional Slim Blade Stand Display with 4K , HDR Processor X1, HDR (HDR10, HLG, Dolby Vision), Direct LED, Dynamic contrast ratio up to 400,000:1,4K X-Reality PROT RILUMINOS PRO technology, 24/7 Portrait ,Tilt functionality, Flexible Conten t Layout with HTML5, 16GB On Board Storage ,Motion flow XR,HDCP 2.3 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 20W Speakers / Android™ OS system, Viewing angle 178 degree, Pro Mode, Pro Display using Apple Air Play & Chromecast Approved Makes- SAMSUNG / SONY / LG

Supply, Installation, Testing & Commissioning of loaded UTP CAT6 Gigabit modular Patch Panel for 24 ports in 1U form factor, with universal A/B labeling Loaded with suitable monetarization with all necessary accessories to complete connectivity.

Supply, Installation, Testing and Commissioning of 1 mtr. Cat 6 Patch cord.

Supply ,installaiton, testing and commissioning of RJ-45 socket outlet point with suitable Front Plate, CRCA sheet steel box with all necessary accessories & hardware etc. with require all accessories to finish the job

SITC of Wall mounted network Rack for 19U switch mounting with fixing accessorie set.

3 KVA On Line UPS with 1 hr Power Backup Supply, Installation, Testing and Commissioning of 3 KVA single phase online UPS model for 60 minute back-up with 8 nos 12 volt 42 AH SMF batteries (Quanta/Exide ),including MS Rack and battery interconnector(1 phase in .1 phase out ) as required complete in all respect Make : Numeric/APC

Comprehensive Annual Maintenance Contract Charges of entire project for 5 years.

FRIENDS ELECTRICALS (BID ID -347938)

M/S TRADING ENGINEERS (BID ID -349012)