Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹18.4 LAccepted-Finance | L1 | Accepted-Finance L1 | |
| 2 | L2₹18.6 L+₹17,644.33 (0.96%)Rejected-Finance | L2 | Rejected-Finance L2 | |
| 3 | L3₹18.8 L+₹37,645.83 (2.04%)Rejected-Finance | L3 | Rejected-Finance L3 | |
| 4 | L4₹18.9 L+₹43,543.30 (2.36%)Rejected-Finance VILLAGE SERKHI P O PAB MANAL TEHSIL SHILLAI DISTRICT SIRMOUR H P | PAB MANAL | SIRMOUR | HIMACHAL PRADESH | 173027 | L4 | Rejected-Finance L4 |
Tender Value
₹18.0 L
EMD Value
₹34,500
Closing Date
7 Jun 2022, 10:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer
Executive Engineer HPPWD Division Paonta Sahib District Sirmour (HP)
C/O Two Nos.class Room in GSS School Chachetti in Tehsil Paonta Sahib Distt.Sirmour (SH-C/O two room with Varandha in Ist floor including stair case).
2022_PWD_60129_11
Tender/641-690 dated 21.04.2022
Open Tender
Civil Works - Buildings
Item Rate
180 days
Chachheti
Please refer tender document
13 documents required · 13 mandatory
₹500
₹34,500
28 Jun 2022
30 May 2022
7 Jun 2022
30 May 2022
7 Jun 2022
30 May 2022
75 days
Amount
Providing form work with steel plates 3.15mm(three point one five milimetres) thick welded with angle iron in frames 30x30x5mm.(thirty into thirty into five milimetres, so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4.00(four) meters and removal of the same for in-situ reinforced concrete and plain concrete work in :-including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
In flat surfaces such as soffits of suspended floors, roofs, landing and the like floors etc. upto 200mm(two hundred milimetres) in thickness. ( As per code No. 5.9.3 Page 80 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Columns, pillars, posts and struts, square,rectangular or polygonal in plan. ( As per code No. 5.9.6 Page 80 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Stair case with slopping or stepped soffits excluding landing ( As per code No. 5.9.7 Page 80 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Beams, cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1.00 mretres in depth in all heights from floor level. ( As per code No. 5.9.5 Page 80 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Edge of slab and brick in walls under 20cm wide(5.9.16.1, Page 81)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and laying cement concrete 1:4:8 ( one cement : four sand : eight graded crushed stone aggregate 40mm(forty milimetres) nominal size ) and curing complete excluding cost of form work in plinth ( As per code No.4.1.8 page 73)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and laying cement concrete work mechnically mixed & vibrated 1 : 1.5 : 3 ( one cement : one point five sand : three graded crushed stone aggregate 20mm(twenty milimetres) nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :-including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Suspended floor,roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor in all level ( As per code No. 0952020000 Page 160 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Stair cases ( except spiral stair cases ) excluding landing but including preparing of the surface and finishing of nosing upto floor two level. ( As per code No. 0952030000 Page 160 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and laying cement concrete 1:1.5 :3(one cement : one point five sand : three graded stone aggregate 20mm.(twenty milimetres)nominal size) mechnically mixed reinforced concrete Chajjas not exceeding 10cm(ten centimetre) thickness upto floor in all level including finishing the exposed surface with cement mortar 1:3 (one cement : three sand ) to give a smooth and even surface centring/ form work and curing complete excluding the cost of reinforcement. ( as per code No. 09340000 Page 156 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing tor steel for reinforcement for R.C.C. work including bending, binding and placing in position complete upto all floor level Thermo-Mechanically Treated bars of grade Fe-500D or more.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)(6.4.2)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing & fixing 12mm(twelve milimetres) thick prelaminated board both side bwp phenol bonded exterior/interior grade panelled shutters with frame of first class deodar wood for doors, including bright finished / black enamelled iron butt hinges with necessary screws 40mm (forty milimetrs) thick frame ( As per code No.1217200000 Page No. 236 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and fixing 19mm (Nineteen milimetres) thick water proof termite resistant commercial board cub board of size 2.05 x 2.65 x 0.50 (two point zero five into two point six five into zero point five zero )metre deep with shutters having three shelves & vertical partitions of 19mm.(nineteen milimetres) thick board, back side of cub board shall be of 8mm(eight milimetres) ply. All exposed cut portions of the boards shall be fixed with hard wood edging of size 19mm x 6mm(nineteen into six milimetres) complete with paino hinges, brass handles,magnetic catchers & Godrej almirah type locks.The exposed surface of shutter shall be laminated with 1 mm thick limination of approved shade & make with necessary scerws, nails & fevicol etc. complete as per drawingNo.717 job No. 3183.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing & fixing anodized aluminium sliding doors bolts anodized colour & shade with bolts & nuts screws etc. complete.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
300 x 16mm (three hundred into sixteen milimetres) size.
250 x 16mm (two hundred fifty into sixteen milimetre) size .
Providing & Fixing aluminium tower bolts ( Barrel type ) anodized transparent or dyed to required colour with screws etc. co mplete :-including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
250 x 10mm (two hundred fifty into ten milimeetres)( As per code No. 9.97.2)
150 x 10mm (one hundred fifty into ten milimeetres). ( As per code No. 9.97.4 )
Providing & Fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
125 mm One hundred twenty five) size
100 mm (One hundred milimetres) size .
75 mm.(seventy five milimetres) size
Providing and fixing mild steel plain grill of required pattern in frames of steel etc. with mild flats, square or round bars with round headed bolts and nuts or by screws. ( As per Code 9.48.1) Fixed to steel windows by welding including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Precast terrazo tiles 22 mm(twenty two milimeteres) thick with graded marble chips of size upto 12 mm(twelve milimetre), laid in floors, and landings,jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm (Twenty milimetre) thick bed of cement mortar 1:4 (one cement:four coarse sand) : 11.16.1 Light shade pigment using white cement including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Precast terrazo tiles 22 mm(twenty two milimetre) thick with graded marble chips of size upto 12 mm(twelve milimetre), in skirting and risers of steps not exceeding 30 cm(thirty centimetre) in height on 12 mm (twelve milimetere) thick cement plaster 1:3 (one cement : three coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of : 11.18.1 Light shade pigment using white cement including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
6mm (six milimetre) cement plaster to ceiling in cement mortar 1:3 ( one cement : three sand ) ( As per item code 13.16.1)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
15mm.(fifteen milimetres) cement plaster in single coat on the rough side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in grith & finished even & smooth in cement mortar 1:6 ( one cement : six sand ) 13.2.2including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/ concrete/ stone walls for interiorplastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in grith & finished even & smooth in cement mortar 1:6 ( one cement : six sand )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
White washing with lime on un-decorated wall surface to give an even shade on ceiling and / or slopping roof including thoroughly brooming the surface to remove all dirt, dust,mortar drops & loose scale of lime wash & other foregn matter. ( As per Code No.13.37.1 New work (three or more coats) )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Finishing wall with weather proof exterior grade emulsion of approved design ( Apexultima ) or its equarlied on nun-decorated wall surfaces ( two or more coats ) to give an even shade & final finish after throughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand papered smooth complete. ( As per Code No.13.60.1)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.2 110 mm diameter including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm.(ten milimetres) gap for thermal expansion. including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
12.42.5.2 110 mm. (one hundred ten milimetres) PVC plain bend.
Providing & fixing M.S. holder bats clamps of approved design to Cast iron or S.C.I. Pipes embeded in & including cement concrete block 10 x 10 x10 cm of 1:2:4 mix ( one cement : two sand : four graded stone aggregate 20mm.(twenty milimetre) nominal size)& cost of cutting holes & making good the wall etc.150mm diametre for PVC pipe. ( As per item Code No. 12.38.2 )including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm.(thirty five into thirty five into five milimetres or thirty five into five milimetre) flat pieces to the existing Tiron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing & fixing windows & ventilators frames manufacture from mild steel channels 75x40 mm.(seventy five into forty milimetre) for end frame & for centre frame 75 x 40mm(seventy five into forty milimetre) & mild steel flat 75 x 4mm.(seventy five into four milimetre) in combination welded together to make one frame to making square steel section with 20x 4mm(twenty into four milimetre) & 12 x 4 mm(twelve into four milimetre) mild steel flat together to make one frame to making square steel section with 20x 4mm & 12 x 4 mm mild steel flat structure of rolled steel section T-7B including glass pans 4mm thick in glazing panel & wire gauge shutters of designation 85G with wire of dia 0.56mm & fixed glazing fixed with T-section including priming coat as including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing and fixing angle iron cup board frames manufactured M.S. angle iron 25x25x5mm (Twenty five into Twenty five into five milimetre) thickness including hinges, jamb, lock jamb, beed and if required angle thrashold of Mild steel angles 25 x25x5mm (Twenty five into Twenty five into five milimetre) thickness welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel nut hinges 2.5mm ( Two point five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface.including all leads lifts and carriage of materials as per the direction of Engineer Incharge.
Providing & fixing moulded hand rail of M.S. hollow pipe 50mm(fifty milimetre) dia welded in stright length over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete ( M.S.flat & balusters of railing shall be measured & paid separately ).including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Providing & fixing mild steel fan clamp type-I of 16mm (sixteen milimetres) dia M.S. bars bent to Shape withhooked ends in RCC slab during laying including painting the exposed portion of loop all as per standard design complete. ( As per item code 10.17)including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.
Painting two coats(excluding priming coat) on new steel and steel based and other metal surfaces with readymixed paint to give an even shade including cleaning the surface all dirt, dust and other foreign matter, sand papering and stoping.including carriage of materials with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge. a)with enamel paint other than white.
Applying a priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil,grease,dirt and other foreign sand papering and knotting with ready mixed paint brushing with white lead for priming including carriage of materials with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge.
Painting two coats(excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping.including carriage of materials with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge. a)with enamel paint other than white.
REHMAN MOHD
mehboob hassanb
yeshpal singh
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .