ADDITION ALTERATION AND SPECIAL REPAIR TO BATHROOM OF 300 SERIES AND 315 KB AND 316 KB AT KATARIBAGH, NAVAL BASE KOCHI

Amount

Dismantling of floor hearth or wall tilling tiles including CM bedding (but not backing) and disposing the rubbish off the premises as directed

Demolition of cement Concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M&L for 25mm thick plain Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in levelling course in floor complete all as specified.

Material and labour for non skid coloured ceramic tiles 7 to 8 mm thick square/rectangular area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including provision of CM screed 15 mm thick in CM (1:6) all as specified and directed.

Material and labour for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including provision of backing coat 10 mm thick in CM (1:4) all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes or top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 ) used instead of exposed portion of PVC sheet beading.wood grain printed colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified.

S&F in repair powder coated aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap eading, screws etc. complete all as specified

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with inimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

Supply and fix aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples all as specified and directed.

Supply and fix 4mm thick frosted glass pin head type and glazing with oil putty / beads in squares not exceeding 0.5 Sqm in each pane all as specified and directed.

Supply and fix stainless steel butt hinges medium weight for 100mm size all as specified and directed.

Supply and fix extruded aluminium alloy handles fabricated type anodised 150 mm size all as specified and directed.

All as per item No 14 here-in-before but 100mm size.

Supply and fix aluminium anodised barrel tower bolt extruded section of 150 mm long all as specified and directed.

M& L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, Type C1, 1:3:6 (using 20mm graded stone aggregate), complete all as specified and as directed.

M&L for rendering 10mm thick on brick or concrete wall surfaces with cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M& L for rendering 15 mm thick CM 1:4 with approved water proofing compound on fair surfaces of brick work or concrete surfaces, finished even and smooth all as specified and directed Note: WPC shall be measured and paid separately.

M&L Preparing new surfaces distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification of two or more coats over a coat with alkali resistant priming paint complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed.

Supply and fix in repairs Snow white vitreous China wash down water closet single piece (pedestal pattern) with slim soft close seat cover (including fixing bolts) including removing old one and connection to drain and flush pipe. Make: Cera CAMPBELL Cat. No.S1013158 or eqivalent make of Hindware / Parryware

Supply and fix in repairs vitreous China wash hand basin of size 580 x 450 mm white, flat back with and including waste fittings brass chromium plated 32 mm with long and fly nut screwed shank excluding taps, waste chain and plug and porcelain stopper but including cast iron brackets all as specified and directed.

S&F in repair pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Pillar Tap with aerator Parryware Cart Part No.Crust T3102A1 or equivalent make of Hindware/Cera

S&F in repair SS grating square 125 mm size with centre circular section removal and fixing type complete all as specified. Make : Hindware/Cera/Parryware

S&F in repairs, PVC bathroom cabinet (white) of size 420 x 300 x 100mm (approx), with one single shutter and built in mirror in front of shutter complete all as psecified and as directed. Make : Hindware/Parryware/Cera

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glassshelf 12 cm wide with chromium plated guard and railing size 60cm long (with brass bracket complete. Make : Hindware/Parryware/Cera

S&F in repairs, corner glass shelf of 5mm thick plain sheet glass and with brass, chromium plated bracket complete all as psecified and as directed. Make : Hindware/Parryware/Cera

S&F in repair SS toilet paper holder including fixing screws complete all as specified. Make : Jaquar Cat No.AKP-35751P/equivalent make of Parryware/CERA

S&F in repair looking mirror beveled edge of size 45x60cm fixed to wooden plugs with chromium plated brass screws and cup washers. complete all as specified and as directed.

S&F 75 mm PVC (SWR) floor trap, plain with grating including ointing with solvent cement all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F 75 mm PVC (SWR) bends any radius all as specified and directed.

S&F 110mm PVC (SWR) bends any radius all as specified and directed.

Taking down cement plastered on Brick/Concrete wall and ceiling including racking out joints, hacking for key, scrubbing down with watercomplete all as specified and as directed.

M & L for 5 mm thick rendering in cement mortar 1:3 on fair faces of of ceiling surfaces finished even and smooth complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for complete removal of existing treatment from wall surfaces complete all as specified.

M&L for 3mm thick wall care putty on wall complete all as specified.

M&L for preparation of new decorated surfaces of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L for preparation of new decorated surfaces of new wall surface and applying three coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls including cornices (plastered or unplastered) and applying two coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated surfaces of ceiling including cornices (plastered or unplastered) and applying two coat of white wash complete all as specified and as directed.

M&L for preperation of old painted wooden surfaces of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preperation of old painted steel surfaces of any description over 10cm width or girth and applying one finishing coat of synthetic enamel paint complete all as specified and as directed.

M&L for writing letters of figures (BLOCK, ROMAN, ITALIAN OR INDIAN) n exc 30cm high all as specified and directed Note : Writing shall be done with thick paint so that they stand out boldly.

Taking down chowkats with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm all as specified and directed.

Taking down shutter and removing to store exc 1 sq. m and n exc 2 sq. m each all as specified and directed.

Cutting holes in brick wall built in cement mortar, depth of embedded exceeding half brick and not exceeding one brick and making goof dismantled portion in cement concrete 1:2:4 type B1 for inserting hold fast all as specified and directed.

Supply and fix mild steel hold fast, clamps plain angle cleats and similar small articles confirming Fe-400-

Supply and fix 2nd class hard wood plain, solid, straight chowkat and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as specified.

Supply and fix 2nd class hard wood 35mm thick glazed,gauged and skeleton door shutters, open rebated and prepared to receive glass,gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass,gauze,etc, size of members of shutters as specified in SSR Part I, Section 8,clause 8.24(a) complete all as specified and directed.

S&F 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter, with wood free EPS 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawingcomplete all as specified.

Material and labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces exceeding 10 cm width or girth including preparation of new surface all as specified and directed.

Supply and fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

All as per item No 59 here-in-before but fixed in repair all as specified and directed.

S&F in repairs 18/19 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber frame-work Cub board shutter, self etc complete all as specified and as directed .

S&F in repair 100mm size of Hasp and staple, safety type,Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and directed.

S&F in repair Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

Supply and fix in repair door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in repair in floor, 140mm over length of cover plats all as specified and directed.

Supply and fix butt hinges medium weight cold rolled mild steel powder coated with mild steel hinges pin for 100mm size all as specified and directed.

Supply and fix aluminium anodised barrel tower bolt extruded section of 200 mm long complete all as specified and directed..

Supply and fix 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for Virified Ceramic tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

All as per item no. 68 above but as in vertical surface over rendering 10mm thick in cement mortar 1:4 complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite over 10mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

Rounding to edges of stone slabs one edge, of any situations complete all as specified and as directed.

Dismantling single layer mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling tile battens of any size including tiling fillets spaced exc 15 cm centre to centre complete all as specified and directed.

Dismantling timber scantlings under 40 Sq cm in section for unframed work in fillets, rails, posts, rafters, purlins etc, in unframed works complete all as specified and as directed.

M&L for roof tiles mangalore pattern interlocking at side joints laid dry complete all as specifiede and as directed.

M&L for ridge or hip tiles to suit mangalore pattern of roofing tiles bedded and jointed in cement mortar 1:6 complete all as specifiede and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and as directed.

S&F 0.71mm thick plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straightflashing(length and girth as fixed) complete all as specified and as directed.

S&F 0.63 mm galvanised corrugated mild steel sheeting with two corrugation side lap fixed with L-type ot J-type or cranked hook bolts in roofs and walls, etc with grade of zinc coating 275 complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50mm thick, on an colour, having tensil strength of 550 Mpa as in roof fixes with self tapping screws all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover filllets complete all as specified and as directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.4923-1997 grade St.-240 all as specified and directed.

M&L for 4 mm thick non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium frame work with screws as in ceiling complete all as specified and as directed.

S&F 4mm thick aluminium composite panel of exterior grade with 0.50 mm thick of aluminium layers on both faces, wrapping by routing of joints, wrapping, bending or turning up/mitred angles as per site requirement and fixing with adhesive (Araldite) by popcorn pins and flat pressed the sheets using musking tape till the banding remein solid, complete all specified and as directed.

M&L for Preparation of new steel surfaces and applying two coats of anti corrosive paint over a coat of appropriate primer complete all as specified.

Taking down of old wooden kitchen cabinets set including frame complete all as specified and as directed

Dismantling boarding, any description, fixed in any position with nails all as specified and directed.

M&L for18mm thick Marine plywood modular kitchen cabinets, inside depth not less than 0.50M , water proof, termite & Borer proof, corrosion free with Decorative laminate 1mm thick both side shutter and auto closer counter sunk hinges, stainless steel handles complete all as directed . ( Note :(i) Only front facing area of cabinet will be measured for payment. (ii) Stainless steel baskets mentioned as supply only under Sl. item No. 03 of this AE shall be fixed under this item as the unit rate quoted against this item is inclusive of this fixing provision) all as specified and as directed.

Supply only a set of stainless steel baskets with fittings as in modular kitchen cabinet as per following details :- (i) Plate basket 21"x19"x8" - 01 No (ii) Plane basket 21"x19"x8" - 01 No. (iii) Plane basket 17"x19"x8" - 01 No. (iv) Cutlery basket 17"x19"x4" - 01 No. (v) Cup & Saucer basket 17"x19"x4" - 01 No. (vi) Single pull out 8" - 01 No. (vii) GT- PT & Drip tray 22" - 01 No. (viii) Telescopic channels of appropriate size - 06 Nos. Make : First quality of Sleek/ Ebco/ Dolin) all as specified and as directed

M&L for 18mm thick Marine plywood, water proof, termite & Borer proof, corrosion free with Decorative laminate 1mm thick both side for cupboard shutter, self, Drawer, including auto closing hinges all as specified and as directed.

S&F stainless steel sink with drainage board made out of 1mm thick sheet kitchen or laboratory with plugs, washers including beding lime cement mortar to dwarf wall or including fixing cantilever brackets fixed to wall and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm including waste coupling 40 mm and waste pipe complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry/Pre-cast cement conrete block built in cement mortar including all quoins, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed.

S & F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls(jointing shall be done with solvent cement) complete all as specified and as directed .

Supply and fixing in repair plastic water closet seat for single piece closet, snow white , closed pattern with flat bottom, and cover and mild steel chromium plated or alumininsed hinging device. Make : Parryware EWC Seat cover E 8305 Ultra Solid white or equivalent make of Cera/Hindware

Supply and fix Towel Rack 600mm long with Lower Hangers, Stainless Steel with brackets fixed in repairs 60cm long complete all as specified. Make :Jaquar AKP-35781PFS equivalent to Parryware/Cera

S&F in repair Towel Ring Round with Round Flange complete all as specified. Make : Jaquar Cart part No. ACN-1121BN/ equivalent make of Cera/Hindware

Supply and fix in repair stainless steel curtain rail bright finished 25 mm dia decorative type complete all as specified and as directed.

Supply and fix in repair stainless steel bright finished decorative brackets/finials for curtain rail 25mm dia complete all as specified and as directed.

M&L for Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

M&L for At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

S&F, on wall/ concealed on wall, 40mm dia. High pressure CPVC pipes SDR-13.5 & Plain CPVC SDR 11 fittings including all necessary fittings, solvents, complete all as specified and directed. Make: Supreme/ Eurotech/ Astral/ SFMC

S&F on wall/ concealed on wall, 25mm dia. High pressure CPVC pipes SDR-13.5 & Plain CPVC SDR 11 fittings including all necessary fittings, solvents, complete all as specified and directed. Make: Supreme/ Eurotech/ Astral/ SFMC

S&F on wall/ concealed on wall, 20mm dia. High pressure CPVC pipes SDR-13.5 & Plain CPVC SDR 11 fittings including all necessary fittings, solvents, complete all as specified and directed. Make: Supreme/ Eurotech/ Astral/ SFMC

Supply and fixed in repairs, 15mm size Chromium Plated fancy type Bib Taps, quarter turn with flange and aerator, short body, cast copper alloy with crutch or butterfly handle, screwed for GI/ CPVC pipe, complete all as specified and as directed. Make : Cera Cat. Part No. F2004151 or any other make from the approved list of manufactures.

Supply and fixed in repairs, 15mm size Chromium Plated cast copper alloy Bib Cock, short body with flange and nozzle for garden/ washing machine, complete all as specified and as directed. Make : CERA Model No. F 2003153 or any other make from the approved list of manufactures.

Supply and fixed in repairs, 15mm size Chromium Plated cast copper alloy Angle Valve, half turn with flange, for fixing with CPVC pipe, complete all as specified and as directed. Make : CERA Model No. F 2004201 or any other make from the approved list of manufactures.

Supply and fixed in repairs, 15mm size Swivel Overhead Shower (minimum weight 40 grams) of PTMT, any colour with shower arm (minimum weight 40 grams) 195mm long with bend of 45 degree with flange, fixing with CPVC Pipe, complete all as specified and as directed. Make : CERA Model No. F 7020104 or any other make from the approved list of manufactures.

Supply and fixed in repairs, 450mm long, 15mm dia. PVC Connection with brass union on both sides to suit 15mm GI pipe, complete all as specified and directed.

Supply and fixed in repairs, Health Faucet, ABS body with wall hook and one metre SS braided rubber hose pipe, complete all as per specified and directed. Make : CERA Model No. F 8030102 or any other make from the approved list of manufactures.

S&F in repairs, Wall Mixer (3-in-1) with arrangement of both Telephonic Shower and Over Head Shower, with 210mm long bend pipe, complete all as specified and as directed. Make : CERA Model No. F 2002403 or any other make from the approved list of manufactures.

Supply and fixed in repairs, Chromium Plated cast copper alloy Kitchen Sink Cock, quarter turn, wall mounted with swivel spout not less than 150 mm and wall flange complete all as specified and as directed. Make : Model No. F 2004251 of CERA or any other make from the approved list of manufactures.

M&L for cutting chases on walls, floors etc. not exceeding 10cm girth and making good the disturbed surface to match with the existing surface after removing the existing concealed pipe/ laying new pipe, complete all as specified and directed.

Supply and Fixing 1000 litres capacity Rotational Moulded Polyethylene Water Storage Tanks (Cylindrical, vertical with closed top), hoisted & fixed in position, complete all as specified and as directed. Make : Sintex (ISI)/ Aquatech

S&F in repairs, 25mm dia. CPVC Ball Valve suitable for CPVC pipe including necessary fittings, complete all as specified and directed. Make: Supreme/ Eurotech/ Astral/ SFMC

S&F in repairs, 20mm dia. CPVC Ball Valve suitable for CPVC pipe including necessary fittings, complete all as specified and directed. Make: Supreme/ Eurotech/ Astral/ SFMC

Supply only 12mm dia. Chromium Plated Pipe for 'Hot and Cold' water, of suitable length, with two brass adopter and connecting up, complete all as specified and directed

Supply and fixing 25 litre capacity Electric Water Heater, Storage type, steel body with copper inner tank and heating element upto 2 KW, BEE 5 Star rated, with all accessories such as safety valve, thermostat, NRV, connection piece etc., complete all as specified and as directed.

supply and fixing in repair centrifugal mini booster pump 0.5 HP, 0.37 KW ,pressure setting range 2.0 to 4.5 kg/cm, tank capacity 24 ltrs ,rust preventive aluminium die casted motor body, fitted with hot water seal, F-class insulation, suitable for hot water application all as specified and directed by engineer in charge. Make:- Cat part no -VB1.H1s of V-gaurd or equivalent model of kirloskar ,bajaj .Head-: 3-6 mtr Note :- Quoted rate shall Include provision of suitable type PVC canopy for protection of booster pump as per direction by engineer in charge. attach .

S&F Concealed stop cock 15 mm 15mm size Chromium Plated cast copper alloy Bib Cock, short body with flange complete all as specified and as directed

Taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, c/ rosess, holders and bracket fittings with battens / conduits / wires,T/L fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

S&F Light / fan point wiring with 1.5 Sqmm PVC insulated sheathed FRLS multistranded single core copper conductor cable in PVC concealed conduit rigid non metalic (ISI marked) fixed concealed on wall/ roof except beam, column and RCC roof including chases cutting incl suitable size/ cap of sunken box for modular switch and socket and modular white cover plate, flush metal box etc including 1.5 Sqmm PVC insulated copper conductor as earth continuity wire for One light point controlled by one switch and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board all as specified and directed.

One 3 pin 5 Amp socket outlet point controlled by one switch on same board all as specified and directed.

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size all as specified and directed.

All as per item No. 128 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed, stranded copper conductor cable all as specified and directed.

All as per item No. 128 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC insulated, unsheathed, stranded copper conductor cable.

M&L Switch modular type 6 amps, 1 module single pole one way duly ISI marked, complete all as specified and directed.

M&L Switch modular type 16 amps, 1 module single pole one way duly ISI marked, complete all as specified and directed.

S&F Socket outlet modular type 6A - 2 in 1,without shutter, 2 module, duly ISI marked, complete all as specified and directed.

S&F Socket outlet modular type 16A, 3 pin combined, 2 module, duly ISI marked, complete all as specified and directed.

M&L Bell push modular type 6 amps, 1 module single pole one way duly ISI marked, complete all as specified and directed.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F of 20 W LED 6500 k trim cosmo surface round slim surface mounted LED panel with premium diffuser to ensoure glare free &even light distrubuition

S&F of LED Decorative wall light fitting 9 Watt 230 V AC not less than 120 lumens /watt. Made up of polycarbonate, outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete make HAVELLS or equivalent make in the approved manufactures list

Supply and fixing LED lights fitting 1x 20W, 220V,AC not less then 120 lumens/watt, 4 feet, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F in replacement of LED street light fitting 35 Watt, not less than 120 Lumens/ Watt, 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC not less then 120 lumens/watt .decorative type with driver holder and LED lamp including connecting up with three core flexiblecopper conductor cable of suitable size complete

S&F Door Bell Ding Dong single phase 240 volts, white in colour, duly ISI marked complete all as specified and directed..

S&F in replacement of Factory made three phase and neutral sheet steel made out of CRCA 1.2 mm thick, powder coated double door distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming MCCBs and outgoing MCB the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 415V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified.

S&F in replacement of Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified.

Supply and fixing TPN/FP 40 to 100 AMP MCB ,415V 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.,

S&F MCB SPN, 40A - 63Amps, 240 volts, "B" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning all as specified.

S&F MCB SP, 6A-40 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning all as specified.

S&F in repairs, SPN Enclosure with two pin and earth plug and socket complete with one SP MCB, 20 Amps having breaking capacity 10 kA, including taking down old unserviceable earth plug, complete all as specified and directed.

S&F in replacement of ceiling fans, complete with blades, down rods, accessories 230V, 1200mm sweep, with min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current (BLDC) including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified. Note : Old Ceiling fans to be deposite at AGE E/M (NW) store yard.

S&F in replacement of exhaust fan steel body heavy duty with louvers complete of sweep size 300 mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified. Note : Old fans to be deposite at AGE E/M (NW) store yard.

S&F in replacement of exhaust fan plastic body heavy duty with louvers complete of sweep size 250mm, 1200 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified. Note : Old fans to be deposite at AGE E/M (NW) store yard.

S&Fixing of exhaust fan plastic body heavy duty with louvers complete of sweep size 250mm, 1200 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including suitable size of cutting/opening the wall for fixing and provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. Provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. Excavation in soft/ loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

M & L Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core

M & L Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 2 core

S&F in repairs, SPN Enclosure with two pin and earth plug and socket complete with one SP MCB, 20 Amps having breaking capacity 10 kA, including taking down old unserviceable earth plug, complete all as specified and directed.

Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for batten fittings complete all as specified and directed.

S&F in repair bed side lamp 3 Watt 50 Hz,230 Volts, 3000 k with all accessories and connection to the electric circuit complete all as specified and as directed. cat part No-48042/30/31 of Philips,crompton,Wipro

Taking down old unserviceable cable any size and make complete all as specified and directed

CREATIVE BUILDERS (BID ID -3458586)

Oriental Constructions (BID ID -3452943)

M.J.JOY AND COMPANY (BID ID -3452368)

Anaswara Constructions (BID ID -3458619)