SPECIAL REPAIR TO BLDG NO. T-262 AND T-329 AND ADDITIONAL/ ALTERATION TO BLDG NO. T-317 AT HASIMARA MIL STN UNDER GE SOUTH BINNAGURI

Amount

Schedule 'A'

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section as in framed work in any position complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat fair finished concrete surfaces complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregate as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately

Form work to chullah hood, chajjas, troughs and similar items including edges fair finished flat concrete surface complete all as specified and directed.

M&L Fly ash Brick work using old size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work using Fly ash bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel bars TMT 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumn , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to complete all as specified and as directed.

Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC @3% by weight of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified and directed. Note-WPC shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 40 mm thick laid in panels & finished even and smooth without using extra cement complete all as specified and directed. Note :-Glass dividing strips shall be measured & paid seperately

M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab size not less than 0.25 sqm) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including cement screed bed 20 mm thick in cement mortar (1:6), complete all as specified and as directed.

M&L for Machine kota stone slab 20 to 25mm thick in riser or steps, skirting, dado and pillar laid over 10 mm thick rendering cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in skirting and dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F MS steel Hollow section Square/rectangular as in roof truss ,purlin,rail etc etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes ,without and attachment of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and directed.

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw complete all as specified and directed.

M&L for non Asbestos ,fibre reinforced standard cement board as in ceiling ,4mm thick designer board (610mm x 610mm ) complete all as specified and as directed.

S & F anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed.

M&L for applying two coats of acrylic distemper on newly plastered wall surface including preparation of surface over a coat of 1mm thick wall care putty complete all as specified and directed.

M&L for preparing of new plastered surface of walls and applying two coat of weather resistance acrylic smooth exterior emulsion paint over a coat of exterior primer complete all as specified and as directed.

M&L for preparing of new plastered surface of walls and applying two coat of colour wash over a coat of white wash complete all as specified and as directed.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new or old steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

M&L for PCC 1:3:6, type C1 (using 20mm graded stone aggregate) as in block of hold fast or similar work including necessary form work complete all as specified and as directed.

S&F 35 mm thick second class hard wood rail and style plain framed factory made paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Powder coated aluminium window sliding type three track (one gauge and two glazed shutter) aluminium sections weighing not less than 0.55 Kg per mtr for shutter including necessary jointing cleats, glazing cleats, rubber packing, screws, handle, locking arrangement etc complete and 5.5 mm thick plain or tinted glass and stainless steel mosquito proof gauge complete all as specified and as directed.

S&F powder coated anodised aluminium frame of size 100x44x1.5mm thick made of square tubler coated aluminium section for doors with one or more rebates ,jointing cleats for fixing etc and provision of aluminium door shutter(single/Double shutter) including jointing cleats ,glazing clips ,rubber gasket aluminium anodised snap beading ,screws hold fast ,floor stopper ,locking arrangement ,handle of size not less then 200mm ,5.5mm thick tinted glass fixed in panels with minimum 3 nos aluminium hinge 100mm long for one shutter etc complete all as specified and as directed.

S&F mild steel barrel tower bolts stove enameled black with bright bolt 150 mm long complete all as specified and directed.

S&F mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 250 mm length of bolt complete all as specified and directed.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and no pigment complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed

S&F Butt hinges, medium weight, cold rolled mild steel 75 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 150 mm length of bolt complete all as specified and directed.

M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for fair finished flat surface of concrete complete all as specified and directed.

M&L for 20 mm thick black granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window, cills, cooking platforms and like in 12mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including full rounding to the exposed surface complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

S&F stop valve, fancy type chromium plated (medium) screwed down, high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union of 15mm bore complete all as specified and directed.

S&F stop valve, fancy type chromium plated (medium) screwed down, high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union of 20mm bore complete all as specified and directed.

S&F bib taps cast copper alloy chromium plated with crutch or butterfly handle fancy type, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia of pipe complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in Soft/loose soil complete all as specified and directed.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B0 using 12.5 mm graded stone aggregate as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for hardcore of gauge not exc 63mm, deposited, spreading and leveling in layers not exc 15cm thick, watered and rammed to true surface with broken stone or boulder complete all as specified and as directed.

M&L for preparation of new surfaces of wall surfaces and applying two coat of cement based paint incl necessary preparation complete all as specified and as directed.

M&L for non Asbestos ,fibre reinforced standard cement board as in ceiling ,4mm thick designer board (610mm x 610mm ) including hot dip GI heavy duty suspended ceiling grid system T-2420 all as specified and as directed

S&F in repair powder coated anodised aluminium guard bar mesh size not less than 65 mm x 65 mm with guard bar of not less than 6 mm dia fixed to flat aluminium windows with & woolen rods straining bolts .and making good disturbed surface of wall complete all as specified and as directed.

Taking down carefully aluminium point wiring for one light, socket or power etc incl all fittings such as switches sockets, holders, light fittings, fan regulators etc and making good the disturbed surface of wall ceiling Complete all as specified and as directed

M&L for concealed Point wiring controlled by one switch with 1.50 Sqmm (nominal area) FRLS, PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable and FRLS, ISI marked, PVC insulated 1100 volts grade multi stranded copper conductor single core of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, drawn through in and including rigid PVC conduit (Medium Grade) of suitable size, with all fittings, ISI marked and accessories, the pipe shall be fixed with clamping and shadle including provision of mild steel terminal boxes/Sunken boxes of suitable size made with 1.6 mm thick mild steel sheet recessed in wall with a coat of black bituminus paint and providing of with 3mm thick bakelite/PVC sheet ISI marked top cover , suitable for fixing of switches / sockets / regulators etc. fixed in recess of wall with brass chromium plated screws and cap washer complete all as specified and directed for the following :- (a) One light point controlled by one way switch 5/6 amps. Complete all as specified and as directed

(b) One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps Complete all as specified and as directed

(c) One socket out let 5/6 amps point on the same board Complete all as specified and as directed

(d) One socket out let 5/6 amps point on the independent board Complete all as specified and as directed

All as per item No 85 here-in- above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board Complete all as specified and as directed

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 5/6 amps single pole one way Complete all as specified and as directed.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S & F Wall mounted slim LED batten 18W, with extruded aluminium housing, with integrated LED driver complete all as specified and as directed.

Supply and fixing LED street light fittings 45 watt in almunium PDC housing, toughned glass cover with IP66 protection complete all as specified and as directed.

M&L for sub main wiring with 3 run of 4.00 sqmm (nominal cross-sectional area) PVC insulated unsheathed single core cable of working voltage 1100 volts grade with stranded copper conductor drawn in PVC rigid non- metallic conduit complete all as specified and as directed. NOTE : (i) Three run of submain wiring cable alongwith 25 PVC conduit pipe shall be measured as one unit length.

S&F Sheet metal enclosure for 8way Distribution Boards (DB’s), double door, single pole and neutral with 200 amps rated bus bar, IP-43 protection suitable for fixing MCB"S/isolators with and incl blanking plates complete all as specified and as directed.

S&F of MCB, Single pole and neutral 40 amps, 240 volts, ‘C’ curve, 10KA all complete as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed.

M & L for street light bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified and as directed.

S & F deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

M&L in replacement for Earthing complete with galvanised steel plate electrode of size 600x600x6.30mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil with and including taking down the old one complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed. Note: The Rate for Taking down the old unsv Earthing shall be deemed to be included in the unit rate complete all as specified and directed.

S&F Ceiling fans complete with blades ,down rods and all accessories ,230V ,1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. 5 star rated with brushless direct current motar (BLDC) complete all as specified and directed.

M/S. VINITA CONSTRUCTION

M/S SARDAR MAL NAHATA

M/S DEY ENTERPRISE

M/S ANNI ENTERPRISE

M/S ANIL KUMAR BAUL

M/S RATHIN ENTERPRISES

JOGINDER KUMAR GOYEL