CERTAIN REPAIR TO MES INSTALLLATIONS FENCING DRAIN AND OTHER MISC WORKS AT ALHILAL MIL STN

Amount

Dismantling posts or struts (Wood, steel or RCC) any section, including taking out embedded portion, posts embedded in natural ground or lean concrete etc and making good disturbed portion, complete all as specified and directed.

Excavation in post holes (or similar holes) each n. exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in any type of soil and making good surfaces, complete all as specified and directed.

M&L plain cement concrete, M-15 (Nominal Mix) type B-2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete etc, complete all as specified and directed.

Mild steel work as in posts & struts in fencing using angle, iron or other sections, including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting and reveting etc. and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Fixing only chain link fencing including line wires,any mesh,size and type to any type of standards,rails,straining bolts etc including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing any size and type , complete all as specified and directed.

Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other ends, or screwed both ends each screw to be fitted with washer and one hexagonal or square nuts, length of bolt not exceeding 30cms long, diameter of shank not exc 12mm, complete all as specified and directed.

Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide zinc chrome primer, complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixed to any type of standard rails straining bolts, including securing or tying at crossing with provision of galvanised mild steel wire, staple or steel pins etc, complete all as specified and directed.

Supply only mild steel round bars 10mm dia and over, cut to length as required and bent the ends in round shape/hook shape in fencing complete all as specified and directed.

M&L hardcore of guage n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, around transformer area of MES installations complete all as specified and directed.

Dismantling of old rested plain or corrugated steel sheeting, any gauge, thickness,including Nainital or similar pattern roof covering etc. complete all as specified and as directed.

Dismantling timber scantlings 40 sqcm and over in section in any position framed or unframed work etc, complete all as specified and directed.

Dismantling timber scantlings area not exc 40 sqcm in fillets,rails,rafters,purlins,etc complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified (framed truss)

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries. rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410-W (Grade E-250) complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins,arches,pillars,etc but excluding ashlar facing,dressed stone work precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

M&L walling of random rubble, un-courses, well bonded bedded & solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling(Granite or trap stone) for hammer dressing with maximum depression on face from a straight edge held against the dressed surface n exc exceeding 20mm and dressing to face beds and joints as specified of random rubble walling un-courses or brought upto coarse complete all as specified and directed.

Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Excavating in trenches, n exc.1.5 m wide and n exc.1.5m in depth; for foundation,etc.or for shafts,wells,cesspits,manholes,pier holes,etc n exc 10 sq m on plan and getting out any type of soil complete all as specified.

Removing excavated soil n. exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in mass concrete complete all as specified and directed.

M&L plain cement concrete,1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in surface channels or drains etc, complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

Add or deduct for each 25 mm girth or part there of over or under 30cm girth, complete all as specified and directed.

M&LPCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in coping including weathering, slightly rounded, chamfered angles and finishing exposed surface even and smooth including necessary form work complete all as specified and directed.

M&L RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in foundation incl rafts, footings, foundation beems, plinth beems for columns etc basement slabs, columns etc complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified.

Rendering 15mm thick plaster on fair faces of brick work or stone masonry,concrete surfaces in cement mortor 1:4 and finished the surface fair and even complete all as specified and directed.

M&L raised pointing to random rubble stone masonry,un-courses or brought upto course in cement mortar 1:3 complete all as specified and directed.

Taking down cement plaster of any description on brick or stone or cement concrete block walls etc including raking out joints, hacking for key, scrubbing down with water etc, and removal of rubbish off the premises and leave the work clear of any plastering complete all as specified and directed.

M&L rendering 15mm thick plaster in cement mortar(1:4) mixed with WPC as per manufacturer's instructions on stone masonry wall surfaces or fair faces of brick work or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid separately.

M&L rendering 15mm thick plaster in cement mortar(1:6) mixed on stone masonry wall surfaces or fair faces of brick work or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L preparation of new plastered or un-plastered surfaces of walls and applying two coats of distemper oil emulsion of approved tint over and including one coat of wall care putty 2 to 3mm to get uniform smooth surfaces, complete all as specified and directed.

M&L preparation of old plastered or un-plastered surfaces of walls by complete removing the existing treatment and applying two coats of distemper oil emulsion of approved tint over and including one coat of wall care putty 2 to 3mm to get uniform smooth surfaces, complete all as specified and directed.

Peparation of new plastered or unplastered surfaces of walls and applying two coats of weather proof exterior emulsion paint (Apex from Asian paint) of approved tinted, over a coat of primer (JK cement primer or equivalent) complete all as specified and directed.

M&L preparation of old plastered or un-plastered surfaces of walls by complete removing the existing treatment and applying two coats of weather proof exterior emulsion paint (Apex from Asian paint) of approved tinted, over a coat of primer (JK cement primer or equivalent) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L reinforced concrete pipes, 300mm dia of bore class NP-2, laid and jointed complete with collars as specified and as directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L pre-cast reinforced cement concrete type B-1 1:2:4 (20mm graded crushed stone aggregate) as in landings, cover slabs for man holes and similar articles, set in CM 1:6 complete all as specified and directed. Note:-Reinforcement shall be measured separately.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring,paver block and paving's not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding or backing coat, removing rubbish off the premises, removal and depositing where directed and leaving the work clear of any plastering complete all as specified and directed .

M&L coloured glazed ceramic tiles in vertical surfaces 300 x 450x 7mm/ 300 x 600 x 7mm as in skirting/dado etc, over and including 10mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick (Square / rectangular) polished area of each tile exceeding 0.18 sqm butt not exceeding 0.38 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the tiles complete.

M&L Non skid coloured ceramic tiles 7 to 8mm thick (Square / rectangular) polished area of each tile exceeding 0.18 sqm butt not exceeding 0.38 sqm cut to size as required in skirting/dado over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the tiles complete.

M&L 25 mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) 25mm thick as in sub base of flooring, leveling course of flooring or levelling course of roof etc, complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (40mm graded crushed stone aggregate) as in sub base of floors/ paver block/ path etc finishing the surface even & fair without using extra cement complete all as specified and directed.

M&L coloured anti-skid outdoor full body vitrified tiles of size 600mm x 600mm x 15mm thick conforming to IS 4457:2007 as in parking/footpath fixed with spacers over 6mm thick high polymer modified grey cement based tiles adhesive and grouted with epoxy grout over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed. MAKE:- Johnson (Meteor series of Johnson Endura) or equivalent make of Somany / Kajaria / Orient Bell /Nitco

M&L 60 mm thick rubber moulded coloured machine pressed precast concrete interlocking paver block any shape and size (shape as approved bt GE) laid in path,porch,hard standing or flooring etc conforming to IS-15658-2006, M-35 grade over and including 25 mm thick layer of sand cushioning, complete all as specified and directed .

M&L 75 mm thick PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate laid in alternative bays area not exc. 2 sq.m. each as in plinth protection laid to slope of 1 in 12 including finishing the surface even & fair & filling the joints (6 mm wide) with mastic filling i.e. one part of bitumen 85/25 or VG-30 and 3 parts of sand by weight complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.50 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

S&F factory made Pressed steel frames of size 165mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F factory made Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F 35mm thick factory made 2nd class hard wood rail and style plain framed, panelled shutter with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part 1) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F rolled mild steel bands,straps,supports or stays for rainwater,ventilating pipes,including bolts,if required; hooks(stays),heavy,for large gates,hook and pintle hinges;large hasps and staples;chains;hand made sliding bolts;clamps;hold fasts;wall ties;hooks for hanging fans;plain angle cleats for securing purlines to wooder trusses conform to Fe-290 Gde E-165 complete all as specified & directed.

M&L PCC 1:3:6 typeC-1 (using 20mm graded crushed stone aggregate) for cills,hold fast etc complete all as specified and directed.

M&L prepartion of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay doytailed at welded incl 2 Nos tower bolts 150 mm long for each leaf and 8 mm square bar grills at spacing as shown on drg welded to FI frame work,incl other fittings,hinges,handles tarred hold fast PCC blocks etc. all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 ,complete all as specified.

S&F factory made Steel windows side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars dovetailed or welded, complete all as specified and directed.

S&F factory made Steel windows side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars dovetailed or welded, complete all as specified and directed.

S&F 100 mm size aluminium butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin ,anodised, type B-21 complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 200 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 4mm thick figured/plain glass pin head type and glazing with oil putty in squares n.exc. 0.50 sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills,gratings,etc,with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bars;barred iron doors;ladders ;framed balusters;walk ways;railings;framedwork of water tanks andsimilar work confirming toFe-290Gde E-165 complete all as specified & directed .

Dismantling of wall & celling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling ( size of grid 605x605mm) including hangers 6mm dia GI (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of G.I. Flat 40mm X 3 mm size 60mm long and expansion hold fasterns 12.5mm dia 40mm long complete all as specified and directed.

M&L 8 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 605x605mm grid complete all as specified and directed.

Dismantling old unserviceable water tanks exc 250 and n exc 500 ltr capacity and removing from site complete all as specified and directed.

S&F 500 litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connections(including fittings) including cleaning for refixing or remove from site complete all as specified and directed.

Taking up or down 20 mm bore steel water tubing and connections(including fittings) including cleaning for refixing or remove from site complete all as specified and directed.

Taking up or down 25 mm bore steel water tubing and connections(including fittings) including cleaning for refixing or remove from site complete all as specified and directed.

S&F steel water tubing, 15mm bore , galvanised, "medium grade" with all fittings and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

S&F steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and short lengths, fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F steel water tubing, 20 mm bore , galvanised, "medium grade" with all fittings and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

S&F steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings, fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F steel water tubing, 25 mm bore, galvanised, "medium grade" with all fittings, fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F in repair vitreous china water closet pan semi-pedestal pattern (Anglo Indian type) white connection to trap 'P' or 'S' and flush pipe etc seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing flooring complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valveless symphonic action type flushing cistern (ISI Marked) low level,whire, with inlet ball valve, float and handle including brackets and 32 mm dia PVC flush pipe, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, with pedeatral white colour of size 550mmx400mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper and PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed.

S&F in repair pillar taps 15mm bore cast alloy with capstan head, chromium plated, screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly-nuts screwed for iron pipe and fixed

S&F in repair fancy type chromium plated bib taps 15mm bore cast copper alloy with crutch or butterfly, handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F stop valve/angle cock 20mm bore cast copper alloy with screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete.

m t construction co

M/S SAI ENGINEER

BHARDWAJ BUILDERS

M/S Bharmouri Construction

M/S R S Kaushal

M/S PARVEEN ENTERPRISES

M/S THAKUR ENTERPRISES