Augmentation of Water Supply at AF Stn Baroda

Amount

NOTE: Schedule ‘A’ Part I to X are under Ser No. 1.00 to 10.00. are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lump sum price worked out for BUILDINGS / STRUCTURES as listed in Sch 'A’ Part I.

Lump sum price worked out for EXCAVATION, EARTH WORK & SITE CLEARANCE as listed in Sch 'A’ Part II

Lump sum price worked out for INTERNAL WATER SUPPLY as listed in Sch 'A’ Part III

Lump sum price worked out for INTERNAL ELECTRIFICATION as listed in Sch 'A’ Part IV

Lump sum price worked out for EXTERNAL ELECTRIFICATION & DG SET as listed in Sch 'A’ Part V

Lump sum price worked out for EXTERNAL WATER SUPPLY as listed in Sch 'A’ Part VI

Lump sum price worked out for ROAD AND PATH as listed in Sch 'A’ Part VII

Lump sum price worked out for SEWAGE DISPOSAL as listed in Sch 'A’ Part VIII

Lump sum price worked out for AREA DRAINAGE as listed in Sch 'A’ Part IX

Lump sum price worked out for COMPOUND WALL, FENCING & GATE as listed in Sch 'A’ Part X

11 SCHEDULE `A' PART-XI MISCELLANEOUS ITEMS OF WORK (Note for items 11.01 to 11.87 The contractor shall quote his rate for each of these items separately. The estimated rate is left blank since the same is not prepriced by MES)

INTERNAL ELECTRIFICATION

S & F ceiling fan of minimum air delivery 210 CFM with service valve 6.00 BEE. Five star rated with brushless direct current motor (BLDC) silent and connecting upto and including provision of flexible three core copper conductor cable 23/0.0076 from ceiling rose including remote controlled electronic regulator.

S & F Exhaust fan metalic type, HEAVY DUTY, 450mm sweep, 1400 RPM, 240V AC Single Phase complete with frame and louvers including provision of flexible three core copper conductor cable of 23/0.0076 upto ceiling rose and grouting 04 Nos full threaded bolts and nuts etc all as specified and directed.

S & F LED lights fitting 1x20W T8 Lamp - (4 feet), 230V, box type batten fitting with driver, holders including 20W LED tube light 5700K Rated CCT energy efficient with lumen efficiency not less than 110 lumen/watt, pf 0.8, IP20 complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed by Engr-in-Charge.

S & F LED batten single tube of 1x10 W (2 feet) 230V, 5700K Rated CCT energy efficient with lumen efficiency not less than 110 lumen/watt, pf 0.8, IP20 complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed by Engr-in-Charge.

S & F LED Building Security Light luminaire LED 45 W 5700K with lumen efficiency not less than 110 lumen/watt, pf 0.8, IP 66 with surge protection device minimum 10KV made up of pressure dia cast aluminum housing with toughened glass and high power LEDs and secondary optics including bracket made of 40mm dia light grade MS Pipe (powder coated) (600mm long) fixed with MS clamp of suitable size grouted on wall with suitable Nos of screws complete all as specified and directed by Engr-in-Charge.

S&F MCB, SPN 230 volts 40 Amps Capacity, 10KA 'C' series, IP20.

S&F MCB, SP 230 volts 05-30 Amps Capacity, 10KA 'C' series, IP20.

M&L for Submain wiring with 02 runs of 4 Sqmm and one run of 4 Sqmm as earth continuity, 1100 V grade PVC insulated, unsheathed FRLSH grade copper conductor cable signle core, pvc insulated, multistranded ISI marked (IS-694) drawn through and including 20 mm PVC rigid conduit heavy grade ISI marked (IS-9537, Part-III) including accessories such as bends, supports etc all as specified. Note : All runs of main cable and earth cable and one run of conduit/casing caping shall be measured as one unit.

EXTERNAL ELECTRIFICATION AND DG SET

Supply and lay cable HT XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty earthed type) 11000 Volts grade with stranded aluminium conductor of size 95 sq mm 3 core complete

Supply and lay cable LT XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 sqmm 3.5 Core.

Supply and lay cable LT XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sqmm 3.5 Core.

All as per item No 11.11 above but Cable of size 70 Sqmm 3.5 Core

All as per item No 11.11 above but Cable of size 35 Sqmm 3.5 Core

All as per item No 11.11 above but Cable of size 25 Sqmm 3.5 Core

Supply and laying un-reinforced precast concrete cable cover, class HV, type 1, flat, size 300mm x 180mm x 40mm all as directed

Supply and laying un-reinforced precast concrete cable cover, class LV, type1, flat, size 250mm x 150mm x 40mm all as directed

Supply and fix cable route indicator (straight and at turning) pedestal type for HT as per IS 1255 and of size 20cmX15cm and 10mm dia circular rod above the GL 60cm & below GL 30cm with & including PC C(1:4:8) in foundation duly engraved HT cable - MES all as specified and directed by Engr-In-Charge.

Supply, installation, testing & commissioning of transformer of capacity 200 KVA step down outdoor type copper wounded 11/0.433 KV (at no load) AC 3 Phase 50HZ on secondary side double wound oil immersed naturally all air cooled (ONAN COOLED) with external cooling tubes/ rediator, delta connected as on primary and star connected with natural brought on secondary) side and having tapping at (±) 2.5%, (±) 5%, (±) 7.5%, to be changed by hand operated OFF LOAD tap changing gear. The maximum temperature rise should not exceed 45 degree centigrade in oil and 50 degree centigrade in HV/ LV winding when measured by the resistance method after continuous full load run in ambient temperature the transformer shall confirming to IS 1180 Part-I : 2014' Level-3 and comprising of following accessories complete all as specified and as directed:-

(a) HV side cable box with 03 Nos porcelains HV bushing with arching horns on HV side suitable for 11 KV complete with busing rods and nuts washers and cable glands suitable for reception of out 3 core 95 Sqmm cable, HT cable complete. (b) 01 No cable end box on LV secondary side consisting of 05 Nos porcelain bushing (One No neutral earth, One No Neutral and Three No for phase connected bushing) with bushing rods and nuts washers and cable complete. (c) Oil conservator with filter type drain valve and oil level gauge. (d) Dehydrating breather with first filling of dehydrating agent. (e) Explosive vent. (f) Thermometer pocket including temperature gauge. (g) Two earthing terminals on tank body to facilitate fixing of 32x6mm GI strips. (h) One No thermometer dial type vapour pressure type having range 0-120 degree centigrade with maximum temperature indicator and re-setting device to maximum temperature including needle of temperature gauge : Max reading painted terminal. (i) Rating plate with terminal plate. (j) Oil level gauge. (k) Oil drain filter valve. (l) Oil filling hole on top cover with plug. (m) Air release valve/ plug.

(n) 4 Nos plain solid cast steel detachable rollers. (o) First fill of transformer oil conforming to relevant ISI and tested upto 60KV dielectric strength. (p) Two No lifting hook at side of transformer. Note. Providing platform for transformer of size 2.5m x2.5mx1.5m high from GL including excavation in trenches not less than 1 mtr, PCC 1:5:10 type E2 for foundation, brick work in cm 1:6 by providing 230mm thick wall alround , PCC 1:2:4 type B1 in copping, plaster 10mm thick in cm 1:6 om brick/ complete surface PCC 1:4:8 type B1 sub base 75mm thick, as in floor PCC 1:2:4 type B1 100mm thick floor using extra cement returning filling and removal on surplus soil, including 2 Nos ISMB 100mm channel painting with 2 coast aluminium paint over a coat of red oxide primer and 3 coats of whitewashing on cement work for fixing transformer including ramp of suitable size mounting of transformer complete all as specified and as directed.

Supply and fix 70 watts LED street light fitting new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP 66 with 10 KV surge protection road way, luminaries with high power LED with optics as light source and suitable drivers etc and connecting complete all as specified and directed, Make :- Crompton greaves Cat Part No LST-70-CDL/ Bajaj Cat No. BRTFG 72W V3 WH LED/ or equivalent in Philips/ Wipro.

Supply, install, test and commissioning factory made THERMOPLASTIC CABLE JUNCTION BOX IP 66/67 "weather proof", with terminals for outdoor installation (with knockouts for cable entry) of size 205x255x112 mm depth with cable entry size of 10-25 Sqmm with terminal including MCB SP A-1 No complete all as directed and specified. Make : Hansel Cat Part No. KF 2525 G or equivalent from make Legrand/ FIBOX (SOLID PC 2528 13G).

S&F single pole, MCB, 6-32 Amps , 'C' curve, 10 KA breaking capacity, 240 V, 50 Hz, AC made from moulded self-existing thermostat plastic complete all as specified and directed.

S&F PVC insulated PVC sheathed copper conductor 1.5 Sqmm 2 Single Core FRLHS multistranded/solid on poles or passing through steel pole 1100 volts grade with suitable cable lugs, clamps, nut bolts etc complete all as specified and directed by Engr-In-Charge.

Supply & fix post top lantern energy saving environmental friendly long life aesthetically designed with symetrical light distribution spun aluminium landscape luminaire with high power 35 watt LED as light source complete all as specified and directed. Cat Part No - RUBYPT35WLED757PSYMTOPC Make : Havells or equivalent from Make given in Appendix 'B'. Note :- (applicable for all LED lights to be incorporated in the subject work) In case of equivalent model to be incorporated, the Parameters like type of body and cover, burninig hours, temperature, lumen etc shall be strictly compared before approval.

Supply, install & testing of High mast 16 mtr high galvanized suitable for 6 lantern symmetrically fitted alongwith switch gear feeder pillar box (comprising control MCBs, Timer switch, contactor, their control gear and having two point suspension system with stainless steel wire rope of 6 mm dia 7/19 guage and double drum winch (350 kg) with power tool alongwith motor (0.5 HP 6 Pole single phase motor), trailing cable (PVC insulated PVC sheathed stranded copper conductor) and luminaire mounting arm, pully assembly, aviation obstruction light, lightning arrester spike including RCC foundation (as recommended by manufacturer) complete all as specified and directed. Note : Lights will be measured and paid seperately.

Supply and fix flood light fitting LED type 120 W high performance IP-66, made out of pressure die cast aluminum housing with toughened glass and high power LED and secondary lenses. System efficiency ≥110/125 LPW including 10 KV surge protection device complete with suitable driver and other fixing accessories complete all as specified and directed by Engr-In-Charge. Cat Part No- JETAPROPLUSFL120WLED757 LTG Make :- Havells or Crompton Cat Part No. LFLN-120-CDL/60-M or equivalent from Make given in Appendix 'B'. Note :- (applicable for all LED lights to be incorporated in the subject work) In case of equivalent model, Parameters like type of body and cover, burninig hours, temperature, lumen etc shall be strictly compared before approval.

S&F for expulsion fuse single pole for HT 11 KV, rating 50 Amps to 100 Amps, ISI marked complete all as specified and directed by engr-in-charge.

Supply, installed, testing and commissioning outdoor type self standing, double door, front and back openable, APFC Panel compartmental type with APFC relay 5 stage with heavy duty MPP capacitor bank 100 KVAR (10KVAR - 1 No, 20KVAR - 2 No, 50 KVAR - 01 No with 7% detuned harmonics filter reactor) with thyrister control module and MCCB TP of 16 KA of 1.5 time of rating currect of capacitor suitable for each control and MCCB TPN 250 Amp 36 KA as incomer including control CT & control wiring complete having following assessories including control wiring with HR FRLS copper wire complete all as specified. (i) Compact modular bolted design, removable side and back panels with option of top and bottom cable entry. (ii) Capacitor installed in removable assemblies for ease of operation and maintenance. (iii) Incoming of APFC panel of MCCB TPN 250 Amps, 36 KA breaking capacity with high electrolytic grade aluminium bus bar of suitable rating.

(iv) 100KVAR (10 KVAR - 01 No, 20 KVAR-02 No, 50 KVAR - 01 No) with thyrister control module and MCCB TP of 16 KA of 1.5 time of rating current of each capacitor suitable for each control. (each capacitor bank equipped with discharge resister) & 7% detuned harmonics filter reactor. (v) High performance microprocessor based 3 phase APFC relay 5 stage with Auto/ Manual Option. (vi) In built 3 phase power analyzer, Amp meter, volt meter and PF meter (each have 1 No). (vii) Capacitor duty thyrister control modules with high thermal current carrying capacity and early make contracts to reduce inrush current for enhancing life of capacitors. (viii) induced air system provided with axial flow fan/ centrifugal fan. (ix) Bottom cable entry system available with front glass for viewing controller and analyzer from front.

Supply, Installation, Testing and Commissioning of Full Bore Electro magnetic Flow Meter with 4-20 mA output, convertor and digital display along with Flow totaliser suitable for Line size of 200mm dia. with inbuilt data logger and GSM based. Flow Sensor: Type: Pulse DC excitation Electrode : SS 316 Electrode type: Round Head Electrodes Meter Tube: SS 304 Liner: Hard Rubber Accuracy : ±0.5 % of MV inclusive of linearity, Flow Transmitter / Converter : Type : Micro processor based & Modular Display language : English Display Two line back lit LCD for indication of actual flow rate, forward, reverse &sum totalizer. Output : One current output (4 – 20 mA) Enclosure: Die cast Al. with polyurethane finish Power Supply : 240 V AC, 50 Hz Note: The Flow meter shall be calibrated at FCRI / any Laboratory accredited by NABL Make: ABB/ Krohne Marshall/Elster

Supply, install, commissioning and testing factory made (CPRI approved manufacturer) LT panel box (KIOSK) indoor type platform mounted suitable for 415 volt, 3 phases, 4 wire, 50 Hz AC supply system all as specified and directed having busbar chamber with insulated copper bus bars 400 amps rating installed on percelain insulators, the panel shall be dust and vermin proof, made of 2mm CRCA sheet duly powder coated outer & inner and individual compartment for MCCB/MCB, Starters & volt/ Amps meter and 50x50x6mm thick angle iron for base frame work. The complete feeder pillar box should be power coated including internal wiring with PVC insulated solid copper conductor FRLS cables appropriate size but not less than 2.5 Sqmm. Front opening type with appropriate cable glands for cable entry, with following accessories:-

Supply, install, commissioning and testing factory made (CPRI approved manufacturer) LT panel box (KIOSK) indoor type platform mounted suitable for 415 volt, 3 phases, 4 wire, 50 Hz AC supply system all as specified and directed having busbar chamber with insulated copper bus bars 400 amps rating installed on percelain insulators, the panel shall be dust and vermin proof, made of 2mm CRCA sheet duly powder coated outer & inner and individual compartment for MCCB/MCB, Starters & volt/ Amps meter and 50x50x6mm thick angle iron for base frame work. The complete feeder pillar box should be power coated including internal wiring with PVC insulated solid copper conductor FRLS cables appropriate size but not less than 2.5 Sqmm. Front opening type with appropriate cable glands for cable entry, with following accessories:-

S&F LT panel outdoor type made out of 3.15 mm thick CRCA sheet floor mounted dust and vermin proof cubical type 3 phase and neutral 415V duly painted with anti corrosive coating and finally epoxy polyster for powder coating of flint grey shade (RAL-7032) fully compartment lised design with 4 Nos of bus bar made of high conductivity 99.9% pure copper of ETP grade suitable for 600 amps prewired with suitable size of copper strip short circuit rating 50KA ( rms) for one second including suitable copper earth strip conforming to IS complete all as specified and directed. INCOMING (i) MCCB 400 Amps 4 pole 36 KA ultimate breaking capacity 36 KA with thermal magnetic setting complete all as specified and directed.-01 No

DG SET

Supplying, installation, testing and commissioning with AMF panel diesel engine driven generating set of 200 KVA capacity of continuous rating at N. T. P fully wired 415 V AC 3 phase, 4 wire 4 cylinder 50 Hz, at a power factor of 0.8 lagging all as per IS-4722/2001 mounted on common base plate and directly coupled through flexible coupling closed couple to diesel engine with dunlop cushy foot mountings (anti vibration) pad in and including acoustic insulated enclosure/canpoy with 70 db noise level at one meter distance from gen set and PCC/RCC foundation as per manufactures recomendation and complete all as specifiedand as directed by engineer-in-charge at site etc & consisting of the following:-

(A) Diesel Engine:- Water cooled with radiator diesel engine (confirming to IS : 10001/10002) of 1500 RPM capacity to match the 200 KVA alternator under NTP conditions with provision of 10% overload for 1 hour in every 12 hours running conforming to IS 6514/ IS 10001/ 10002 the engine shall consist with water pump assembly turbo charger, battery charging alternator of 12 V instrument panel, electronic in built, governor suitable battery heavy duty with leads suitable size on exhaust pipe of suitable length inclusive of exhaust coupling inside acoustic enclosure and residential silenceer pipe above canopy all as specified & directed by OEM and all other standard fittings/fixtures and all as per OEM specification complete as per IS-1602 for the generator including the following:- (a) Engine protection devices including audio visual indicators & OFF system during low iube oil pressure high water temperature over speeding of engine (b) Radiator cooling system comprising of radiator fan blade water pump with belts thermostant guard (c) Hour meter Make- Mahindra/Cumins/CG

(B) BRUSH LESS ALTERNATOR. (i) Alternator coupled to engine through a flexible coupling to an indigenous alternator mounted on strong steel fabricated base frame suitable for mounting on a permanent foundation brushless alternator shall be conforming to BS-2613 or relevant IS-13364. (ii) Type : Self excited self regulated with automatic voltage regulator. (iii) Rating : 62.5 KVA at 0.8 PF lagging 4 pole horizontal at NTP condition 3. (iv) Speed : 1500 RPM. (v) System : 415 Volts +/- 2.5% AC 3 Phase 4 wire 50 Hz (vi) Connection : 4 wire star connected. (vii). Enclosure : Screen protected dip proof. (viii) Ventilation : Self ventilated. (ix) Insulation : Insulation Class H. (C) FUEL TANK. Capacity to hold diesel sufficient for running 16 hrs running at full load including necessary piping.

(D) AMF panel:- The AMF panel shall be fabricated & mounted on 100 mm MS channel frame shall be totally enclosed cubical type fabricated out of 2mm thick CRCA sheet duly powder coated with 7 tank chemical powder coated process locking arrangement provn of self ventillation with wire mesh etc complete including with base etc 2 sets of 3 nos contactors 4 pole 415 V 50 Hz AC supply for DG auxlliary contactors relays for automatic operation of DG set incase of failure commerial supply & vice versa tinned copper busbars of 1.8 times of alternator rated capacity with heat shrinkable PVC sleeves cable termination box with suitable size of glands and comprising following accessories all as specified & directed by engineer-in -charge

(E) Acoustic insulated enclosure/canopy for gen set:- The gen to be provided with acoustic insulated enclosure/conopy fabriciated out of CRCA sheet 16 SWG & pre treated with 7 tank phosphating prior to polyester coating painting close fit type compact enclosure provided with adequate ventilation system to ensure perfect aspiration and cooling of the DG set to be housed inside and avoide over heating /power deration. Acoustic insulation sound proofing should be made with a high quality insulation conforms to UL94-HF1 class for flammability and suitable including the folliwing:- (a) Control pannel should have blanking windows made out of tuffened glass provided with rubber beading (b) Emergency stop button should be easily accessable

(c) Provn of fitting of branded make including wiring inside canopy (d) Access to fill fuel tank control shall be from out side the canopy enclosure (e) All door, windows pannels should be lockable with single key (f) Single/multi point lifting facility should be available on the base frame (g) Access to fill the radiater from out side the canopy (h) Specially designed as per manufacturers standard alternators are to be provided control sound at entry to canopy and exist from canopy (j) Adequate ventilation has to be provided to meet the air requirement of engine and alterator Note:- (i) Tempareture risein the compartment/canopy should be less than 5 degree centigrade

(c) Provn of fitting of branded make including wiring inside canopy (d) Access to fill fuel tank control shall be from out side the canopy enclosure (e) All door, windows pannels should be lockable with single key (f) Single/multi point lifting ficility should be available on the base frame (g) Access to fill the radiater from out side the canopy (h) Specially designed as per manufacturers standard alternators are to bek provided control sound at entry to canopy and exist from canopy (j) Adequate ventilation has to be provided to meet the air requirement of engine and alterator Note:- (i) Tempareture risein the compartment/canopy should be less than 5 degree centigrate

EXTERNAL WATER SUPPLY

Supply, install, testing & commissioning horizontal split case 2 stage 37 KW/ 50 HP capacity centrifugal pump set with CI casing, high tensile steel shaft, bronze impeller priming funnel with electric driven of capacity 1410 LPM at 60 mtr head,1450 RPM, 415 volts TEFC foot,with suitable capacity of squirrel cage induction motor with base foundation made out of ISMC 75 duly painted with anti corrosive paint installed on suitable PCC foundation(1:2:4) type B1,bolts nuts anti vibration pads with self priming arrangement as recommended by manufacturers instructions all as specified and directed comprising the following. (a) PVC insulated multistranded copper conductor cable of suitable size from starter, panel to motor drawn through and including suitable size of GI pipe medium grade embedded in the floor and flexible PVC conduit of suitable size from starter to GI pipe and from GI pipe to motor. (b) Common base plate for pumps and motor. (c) Provn of MS sheet 3.5mm thick top canopy of suitable size for covering of pump set including two coats of synthetic enamel paints over a coat of red oxide primer. Make:Model No DSM 65/32A (100X80mm) of KIRLOSKAR or Equivalent in CROMPTON GREAVES /KSB. Note : The shall rates shall deemed to be included for provision of all above provisions including PCC foundation.

Supply, install, testing & commissioning horizontal split case 2 stage 15 KW/ 20 HP capacity centrifugal pump set with CI casing, high tensile steel shaft, bronze impeller priming funnel with electric driven of capacity 1410 LPM at 12 mtr head,1450 RPM, 415 volts TEFC foot,with suitable capacity of squirrel cage induction motor with base foundation made out of ISMC 75 duly painted with anti corrosive paint installed on suitable PCC foundation(1:2:4) type B1,bolts nuts anti vibration pads with self priming arrangement as recommended by manufacturers instructions all as specified and directed comprising the following. (a) PVC insulated multistranded copper conductor cable of suitable size from starter, panel to motor drawn through and including suitable size of GI pipe medium grade embedded in the floor and flexible PVC conduit of suitable size from starter to GI pipe and from GI pipe to motor. (b) Common base plate for pumps and motor. (c) Provn of MS sheet 3.5mm thick top canopy of suitable size for covering of pump set including two coats of synthetic enamel paints over a cote of red oxide primer. Make:Model No DSM 65/32A (80X65mm) of KIRLOSKAR or Equivalent in CROMPTON GREAVES /KSB. Note : The shall rates shall deemed to be included for provision of all above provisions including PCC foundation.

Supply, lay, test & commissioning of ductile iron pressure pipes of 350 mm bore class K-9 of type push on joints (Rubber Gasket Joints) conforming to IS 8329/2000, IS: 12288: 1987 Code of practice for laying in trenches all as specified.

All as per item No 11.35 above but 300mm bore

All as per item No 11.35 above but 250mm bore

All as per item No 11.35 above but 200mm bore

All as per item No 11.35 above but 150mm bore

All as per item No 11.35 above but 100mm bore

All as per item No 11.35 above but 80mm bore

Supply & lay in trenches/ fix to Walls 65mm bore GI medium grade pipe, ISI marked inclusing fitting such as tees, bend, elbows complete all as directed by the Engineer-in-Charge.

Supply and fix ductile iron air valves of size 150mm bore with two air outlets, conforming to IS 14845 and fixing to pipes complete all as specified and directed by Engr-In-Charge.

Supply and fixing of granules based chlorine dosing system having high pressure single head gear motor (single phase 230V) adjustable dosing pump having output 2GPD to 40 GPD and adjustable high pressure upto 100 PSI (7Kg/Cm square with accessories lead tubing connation nut injection check valve clay weight and ferrules and FRP tank with lid and level gauge alongwith agilator and shaft & blade plastic mounted on tank, with following:- (i) Preparation tank. (300 Ltr) alongwith water inlet line, outlet strainer, drain and overflow pipe, conical bottom for sludge disposal port hole cover, level gauge having single phase 120 W 900 RPM 1 Phase flange mounted motor with plastic shaft and impeller. (ii) Service tank. Capacity 100 ltr having dosing pump mounting arrangement, level gauge, drain / overflow pipe. Make - POTTER AND WATTS/ RAMCO/ AQUA PURA/ BRIOZNG/ DECLIBAC.

Supply only Calcium hypochlorite 65%-70% chlorine content (calcium based granular disinfectant for a water disinfection treatment complete all as specified and directed.

M & L for costruction of valve chamber with Fly Ash Brick masonry built in CM (1:4) with MS covers 3 mm thick and 50 x 50 x 6 mm duly painted with locking arrangement including excavaton and earth works in any strata, PCC (1;4;8) type D2 for foundation PCC bed/coping in cement concrete (1:2:4) type B1 plastering 15 mm thick with Cm 1:4 painting with one coat of bituminous black paint over a coat of red oxide primer on all steel surface complete all as specified and directed by Engr-In-Charge for the following sizes of chambers :-

(a) 1200 mm X 1200 mm X 1200 mm.

(b) 900 mm X 900 mm X 900 mm.

S & F foot valve gun metal conforming to IS 4038 of size 80 mm (3'' ) bore complete all as specified and directed. Make- Sant/Normex/Perth

S & F foot valve gun metal conforming to IS 4038 of size 100 mm (4'' ) bore complete all as specified and directed. Make- Sant/Normex/Perth

S&F Ductile Iron specials/ fittings confirming to IS (any type radius and angle) such as bends, Tapers, straight, increasing / decreasing or double socket / flanged end collars, connecting pieces etc, as required at site all as specified and as directed by the Engineer-in-Charge.

S&F seamless mild steel header dia 550mm of 6 mm thickness for suitable length with three number ( one Spare) 80 mm bore MS flange type inlet and two numbers 150 mm bore, one number 100mm bore and two numbers 200mm bore ( Spare two nos) MS flange type outlet openings and provision of one outlet on top of the header for and including one 100 dia air release valve with PCC and earth work complete all as specified and as directed by the Engineer-in-Charge.

M&L for MS connecting pieces both end flanged and other end reducers/ bell mouth pieces, bends, blanking plate, tapers and pipes for suction and delivery from pump, any size, any type and radius and angle, tee pieces, single branch, 'Y' junction, double branch, both end flanged including gas welding machine and electric welding to required length including required size of bends, tees, flanges, nuts, bolts and washers, rubber gasket etc for provision suction/ delivery pipe including welding work finishing and painting with approved paint all ends socket, all ends flanged of size upto 300 mm made out of MS plate suitable thick conforming to Fe 410-0 or Fe-310-0 complete all as specified and directed.

Supply & Fix tyton rubber neoprene gasket of size 350mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 300mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 250mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 200mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 150mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 100mm for jointing DI specials.

Supply & Fix tyton rubber neoprene gasket of size 80mm for jointing DI specials.

Supply Installation Testing and Commissioning (SITC) of non clog submersible pumpset. Rated Flow : 27 m3/hr, Rated Head : 12 mtr, Min 2 HP Capacity pump Moc : Casing & Impeller - CED Coated CI, Shaft : SS 410, Outlet : 80mm, Partical Size : 23mm, Liquid Temp : 0 to 50 Deg. Cel, Recommended Ph Value of Liquid : 6 to 8, Motor : 2-Hp, 2900 rpm, 3 Phase, 50 Hz. (For sludge pump).

Supply Installation Testing and Commissioning (SITC) of non clog submersible pumpset. Rated Flow : 21 m3/hr, Rated Head : 16 mtr, Min 2 HP Capacity pump Moc : Casing & Impeller - CED Coated CI, Shaft : SS 410, Outlet : 80mm, Partical Size : 23mm, Liquid Temp : 0 to 50 Deg. Cel, Recommended Ph Value of Liquid : 6 to 8, Motor : 2-Hp, 2900 rpm, 3 Phase, 50 Hz. (For backwash recirculation pump).

Supply and fix Non rising Sluice Valve design standard IS-14846 of class PN 1.6, flanged type cast iron body with stainless steel spindle, inclduding grease jute gland packing and natural rubber gasket with necessary bolts and nuts complete suitable of size 350mm bore all as specified and directed.

All as per item No. 11.61 above for Non rising Sluice Valve of size 300mm bore.

All as per item No. 11.61 above for Non rising Sluice Valve of size 250mm bore.

All as per item No. 11.61 above for Non rising Sluice Valve of size 100mm bore.

All as per item No. 11.61 above for Non rising Sluice Valve of size 80mm bore.

All as per item No. 11.66 but for 80mm bore.

All as per item No. 11.66 but for 65mm bore.

Supply installation, test and commissioning of Air Blower, electrical driven working voltage range 370 to 450V, 3 Phase, Air blower discharge flow rate specified as 735 Cum/Hrs with pressure rating @0.35 Kg/ Sqcm delivery sizes 150mm bore complete with suitable size of PCC 1:3:6 type C1 foundation all specified as directed. Make : M/s Sombansi Enviro Engg Pvt Ltd (SEEPL)/ M/s SIMA Labs Pvt Ltd/ Water Max technologies/ Ion Exchange (India)/ Airvak Blowers Pvt Ltd

Supply installation, test and commissioning Chlorine Dozing Pump operating at 230 Volt AC, 50 Hz with PVC suction/ Delivery tubing of not less than 4mm dia, 3m length, suction filter cum foot valve, injection/ back pressure assembly inlcuding complete working sodium hypochloride dose rate minimum level upto 0-10 LPH/ 3mg/lit, NAOCL concentration @10%, NAOCL PPM @ 100000 mg/lit, dosing flow rate minimum level upto 5.625 LPH all as specified and directed. Make : M/s Satya Sai Aqua Pura services/ E doze/ Grundfos pumps india/ M/s Optimus Enviropro Pvt Ltd/ SIMA/ SEEPL/ M/s Pristine water.

Supply installation, test and commissioning ALUM Dozing Pump operating at 230 volt AC, 50HX with PVC suction/ Delivery tubing of not less than 4mm dia, 3m length, suction filter cum foot valve, injection/ back pressure assembly including complete working sodium hypochloride dose rate minimum level upto 0-21 LPH/ 20 mg/lit, concerntration of alum solution @7.9% all as specified and directed. Make : M/s Satya Sai Aqua Pura services/ E doze/ Grundfos pumps india/ M.s Optimus Enviropro Pvt Ltd/ SIMA/ SEEPL/ M/s Pristine Water.

Supply installation, test and commissioning operating Chemical Dosing system suitable to inject solution upto 25 LPH comprising dosing pump coupled with three phase electric motor of capacity 0.5 HP , 1440 RPM assembly with agitator in one motor, agitator with SS sweep blade duly FRP coated, complete unit mounted on heavy duty MS fabricated frame duly anticorrosive paint complete. Make : M/s Satya Sai Aqua Pura services/ E doze/ Grundfos pumps India/ M/s Optimus Enviropro Pvt Ltd/ SIMA/ SEEPL/ M/s Pristine Water.

Supply installation/ design, test and commissioning sliding gate 32x32mm MS square frame structure with cast iron plate with dia 32mm stainless steel threaded shaft with 75mmx40mm top side channel to operate the gate 400mmx400mm in outlet of tube settler at site including all accessories complete all as specified and directed

All as item No. 11.73 above but for gate 350mmx350mm.

All as item no. 11.73 above but for gate 150mmx150mm.

Supply and fix C.I. Electromagnetic Water Meter type Magnetic Drive Class_B Flanged end suitbale for delivery line 350mm dia working pressure 25Kg/CM2, Digital display, including 10 Metre cable length fixed complete all as specified and directed. Make : Kranti, Dashmesh & Manikant brother (Mumbai), Flow tech

Supply and Fix in pressure gauge 100mm dia MS body, Brass connections & move, dry type, including threading front panel mounting & dial dual scale for water pipe line working pressure 28Kg/cm2 complete all as specified and directed. Make : M/s Satya Sai Aqua Pura services/ Precision Mass/ General.

Supply and installation tests and commissioning LT Panel board outdoor, cubical type, of suitable size floor mounted outdoor type made out of 3mm thick CRCA sheet CPRI Approved, weather proof and 40x40x6mm anglle iron frame work duly Powder Coated suitable size consisting of following items includsive of 250 amps rated bars with epoxy insulators (Aluminium of suitable size) - 4 Nos (1 Set). (a) Star delta starter fully automatic suitable for 415 V AC for 25 HP Motor - 02 Nos for air blower (b) Starter fully automatic suitable for 415V AC for 2HP Motor - 04 Nos (for nonclog submersible pumpset 2 HP) Make : L&T/C&S/CG. (c) Contractor and relay assembly suitable for Agitator 0.5 HP motor - 02 Nos. (d) Incomer - MCCB 3 Phase 50Hz 4 Pole 415 V 250 Amps 35 KA - 02 Nos, Outgoing - (i) MCCB 3 PHase 50 Hz 4 Pole 415V 120 Amps 25KVA - 02Nos, (ii) MCCB 3 Phase 50 Hz 4 Pole 415 V 100 Amps 25 KA - 04 Nos, (iii) MCCB 3 Phase 50 Hz 4 Pole 415 V 63 Amps 16 KA - 02 Nos Make : C&S Model CSE1M125ATM4P- 02 Nos. (e) Multifunctional meterr Make : C&S Model CSM-A-M4-S3 - 01 Nos. (f) Indicator lamps - 03 Nos (g) PCC foundation. (h) Single Phase preventor - 06 Nos.

Note :- (i) The MCCBs should be fixed type. (ii) The panel shall complete with all internal wiring and bus bars of suitable ratings. (iii) Cable entries shall from the rear bottom at the back of the panel through gland plates. (iv) Lt Panel shall comprise of main horizontal bus bars and auxilary vertical bus bars, bus bars/ connection shall be suitably sleeved by heat shrinkable colored sleeves. Panel manufacturer should posses CPRI test certificate of rated capacity.

Supply and lay cable LT XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 Core.

Supply and fixing 1100 volts PVC insulated stranded FRLS copper conductor of size 4.0 Sqmm 4 core from control panel to instruments complete all as specified and directed.

Supply and fix Rigid non - metallic PVC conduit 32mm dia inclusive of all tees, bends, elbows, reducers, bellmouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipehooks for connecting cable from panel to instrument etc complete all as specified and directed.

Supply and fix Rigid non - metallic PVC conduit 40mm dia inclusive of all tees, bends, elbows, reducers, bellmouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipehooks for connecting cable from panel to instrument etc complete all as specified and directed.

M&L for 32x6mm galvanised iron Earth continuty conductors or main earthing lead fixed to wall on battern or recess or chases or buried in ground or drawn through conduit/ pipe or fixed to poles or any other indicated situation for earthing etc. Note : Conduit/ pipe shall be measured and paid seperately.

Supply installation testing and commissioning of tube settler filter media (PVC cool tubes, loose leaves) plan setting area : 11m2/m3 at 60° angle inclination, vertical height 1000mm, media length 1155mm, maximum continuous working temperature 55°C, tube and fitting : Tongue and groove type, thickness 1.1mm (+/- 0.1mm), black color suitable in water treatment plant complete all as specified and as directed.

ROAD AND PATH

M&L for design mix on M-30 using 40mm graded stone aggregate as in floor, pavement, hardstanding and like including necessary form work and broom finishing for thickness of concrete upto 25 cm complete all as specified and directed.

SEWAGE DISPOSAL

M & L for LLDPE septic tank 2000 Ltr capacity (or nearest higher size), No of chambers 3, manufactured by Sintex/Aquatech, including excavation/earthwork in any strata, PCC 1:3:6 100mm thick for placing septic tank complete all as specified and directed.

MEHUL GEO PROJECTS LLP

RAMDEV CONSTRUCTION CO.