Development of Open Spaces, Playgrounds and Museum of freedom Struggle in West kochi Under Smart Cities Mission (Second call)

Amount

Civil works for open spaces and play grounds

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.23.2 : Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm

15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.19 : Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per directions of Engineer -in-Charge.

15.36 : Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead.

16.83 : Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

16.84 : Laying old cement concrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost.)

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

od102906/2019_2020 : Filling with contractor own earth (excluding rock)using red earth and sand/M sand in the ratio 1:1 , in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.2.3 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od26883/2019_2020 : Supplying installation at site:<br>Welded steel wire fabric of required width having rectangular mesh with supports/ frame work as per drawing painted with a coat of primer

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

14.43 : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

14.66.1 : Finish walls with Acryllic Smooth exterior paint of required shade:Old work ( Two or more coats applied @ 1.67 ltr/10 sqm) on existing cement paint surface

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

od32466/2019_2020 : Applying Roll- on surface material A solvent free high build two pack seamless tough skid resistant 1-1.5 mm thick green (or as required) based on gloss and colour retaining acrylic cross linking resin system for cycle track and similar application including surface cleaning ,cost of materials ,transporting ,loading ,unloading etc complete using plastitrack or equivalent

11.20.2 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Medium shade pigment using 50% white cement 50 % Grey cement

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

od101124/2019_2020 : Providing and fixing 40mm thick machine cut, rough flamed finish at top surface only, shell white colour Granite for stone seater/copping and similar locations, of size 60x30cm, laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, etc. complete at all levels.<br>Area of slab over 0.50 sqm

od19782/2019_2020 : :Providing and laying factory made anti skid stone finish, Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, of 60mm thickness & size/ shape of 455x455 mm , made by table vibratory method and PU coated, laid in required colour & pattern over 50mm thick compacted bed of 6 mm aggregate, compacting and proper embedding/laying of inter locking paver blocks into the aggregate bedding layer<br>through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. Paver block of M-35 grade with approved colour, design & pattern.

11.45 : Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mmthick sub grade of compacted bed of 20 mm thick nominal size stone aggregateand base course and filling with 150 mm thick jamuna sand, including spreading,well ramming, consolidating and finishing smooth etc. all complete as per directionof Engineer-in-charge.

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

10.26.3 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

16.93 : Providing and placing in position 100mm thick factory made machine batched & ma chine mixed PrecastRCC Rectangular Covers on drains of footpath of various sizes,of M-25 grade cement concrete for RCCwork, including cost of centering, shuttering, reinforcement of 8mm dia TMT bars of Fe 500 grade @maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on alledges with 1.6 mm thick , 100mm wide MS sheet duly painted over priming coat , reinforcement to bewelded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage ,allleads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge .

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.4.1 : Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.5 : Rough dressing the trenched ground including breaking clods.

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

od26544/2019_2020 : Providing & laying buffallo grass turf with existing ground prepared with proper level and ramming with tools wooden the the surface smoothen and light watering the same, with sprinkler and maintenance for 30 days or more till the grass established properly as per direction of officer in charge.

30.2.57.1 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per trees plants (for 100 nos.=427.45/100)

30.2.57.2 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Shrubs plants (for 200 nos.=427.45/200)

30.2.57.3 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Hedge plants (for 300 nos.=427.45/300)

od33792/2019_2020 : 10236 Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot.: Rs 20<br>

od34039/2019_2020 : Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. plant in 40 cm Cement Pot

od34276/2019_2020 : Spathodea campanulata of plants height 150-165 cm. in big poly bags of plants size 25 cm

od34278/2019_2020 : Pongamia glabra (Papri) of plants height 120-135 cm. in big poly bag of plants size 25 cm

od34317/2019_2020 : Azadirachta indica ( Neem ) of plants height 120-130cm in big polybag of plants size 25 cm

od34318/2019_2020 : Bignonia venusta (Golden shower) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

od34320/2019_2020 : Providing of Monestaria plant mounted on moss stick 90 cm ht., 2 to 3 plant in one pot well developed with fresh & healthy foliage in 25 cm size of Earthen pot / Plastic pot.

od34321/2019_2020 : Providing of Money Plant Broad Leaves mounted on moss stick 90 cm ht., 3 to 4 plants in each pot, well developed with full of fresh & healthy leaves in size of 25 cm Top dia x 18 cm Bottom dia x 25 cm Perpendicular height Earthen pot / Plastic pot.

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

od22263/2019_2020 : Providing and fixing CI cover for trap/opening having weight not less than 2 kg size30x20 cm

od101148/2019_2020 : Supplying and Fixing Granite bench of size 1.5m long , 45cm high and 70cm width with back support including conveying labour charges etc complete

od20904/2019_2020 : Supplying and fixing granite stone bollards 150 mm dia height 1100 mm fixed in cement concrete 1:2:4 ,900 mm above ground , (the size ,finish and designs of bollards to be approved by engineer in charge )

od32400/2019_2020 : Supply and fixing in position Granite stone Smooth Pergola Pillar of size 6"x6"x9'.

od32420/2019_2020 : Supply and fixing in position Granite stone Pergola Coping Smooth finish of size 4"x 12"x 12".

od32421/2019_2020 : Supply and fixing in position Granite stone Pergola Beam Smooth finish of size 6"x 4"x 11'.

od32423/2019_2020 : Supply and fixing in position Granite stone Pergola Rafter Smooth finish of size 2.5"x 5.5"x 8.5'.

18.42.2 : Boring with 100 mm diameter casing pipe for hand pump/ tube well in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump/tube well is lowered and tested:Beyond 6 m and upto 12 m depth

23.3.1 : Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS : 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer- in- Charge.100 mm nominal size dia

18.48 : Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.18.2 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.19.4.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreHorizontal

18.19.5.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):65 mm nominal boreHorizontal

50.18.8.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

50.18.8.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

50.18.8.4.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

Electrical works for open spaces and play grounds

od103403/2019_2020 : Supply, installation, testing and commissioning of  8 meter GI pole with single arm bracket (1m) for illumination of volley ball court using 8M height Pole made of in combination of hot dip galvanised mild steel pipe sections 114mm dia. & 89mm dia. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(80 microns Minimum ) for the effective corrosion resistance . The pole shall be able to withstand wind velocity of 180 km/hour.The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedestal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint . The cost is inclusive of making RCC  Foundation and erection charges with special T&P, for street Light pole duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.45Mtr x 0.45Mtrs x1.20 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. and earthling of light poles and  Supply and laying the 4 core 10 sq.mm ( Aluminium) cables. The conductors shall be annealed, stranded high conductivity Aluminium high grade, HRPVC insulated, laid up extruded PVC (FRLS) inner sheathed, single galvanized round steel/Aluminium wire armoured and overall jacketed with PVC (FRLS) PVC sheathed cable of 1.1 KV grade aluminium conductor armoured approved make in DW HDPE duct pipe as per IS:1225 including excavation of 30 cmx 75 cm size trench, 25 mm thick under layer of sand, second class brick covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. Supply, testing and Laying PVC steel/GI wire/flat armoured cable of 1100 V grade of Aluminium Conductor of following sizes in trench as per standards, with necessary cable identification mark to be provided at distance of 10 MT and cable tag at two ends of the cable and cable laid in 63 mm· die (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe .lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. including excavation and backfilling of earth, cable terminations using double compression cable glands and cable lugs. All light poles shall be earthed to nearest earth pit using GI wire.

od103439/2019_2020 :  Supply, installation, testing and commissioning of 114 W LED street light fixture on 8 M street light pole for illumination of volley ball court die cast aluminium top cover made of pressure die-casting process in single piece, is tilt able, to access the wiring and optical compartment. Bottom frame in die cast aluminium made of pressure die-casting process in single piece with space for the wiring and support of the glass screen. A Silicone gasket is provided between the lower frame and cover. Shield in extra-clear tempered glass with impact resistance IK 08 (EN 62262),Osmotic valve for balancing the internal / external pressure. The Coupling offers a tilt adjustable up to -20° in steps of 5°. Pure polyester powder coating in RAL 9007 Colour. IP Rating - IP 66. Overall Light fixture Efficacy should be> 115 lm/W minimum (Same should be supported by LM79 report from UL Authorised laboratory). Area Exposed to Wind(S) - 0.066 m2 Power LED's Module asper the data sheet ( Individual LED's Minimum Luminous Flux (lm) is 164lm @ 350mA (@ 85 °C) same should be supported by LED manufacturer's tech sheet) in compliance with IEC 62031(supporting test report should be submitted from UL Authorised laboratory), on Printed Circuit Board with metal core plate. Colour Rendering Index: Ra > 70. Dimmable Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection up to 6kv(differential)/10kV(common)(an additional surge protection device of 10kV also provided in-built the fixture).Modular (2 X 2) refractive lens in PMMA with Type-II/III/IV photometric distribution options. NTC sensor on LED plate for control of dangerous temperatures.LM80 Reported LED Lifetime is L90@ 50,000hours minimum.(same should be supported by LM 80 report from NVLAP accredited lab) & Estimated LED Lifetime is L85 @ 100,000 hours(Ta-25°C) minimum(supporting TM21 calculation should be supported). Overall light fixture in compliance with IEC 60598-1,60598-2-3(supporting test report should be submitted from UL Authorised laboratory) Sample Should be submitted for concerned engineer in charge for approval of light fixture. The cost is inclusive of laying and termination of 3CX1.5 sq.mm FRLS flexible copper cable form junction box of street light pole LED fixture.

od103441/2019_2020 : Supply, installation, testing and commissioning of  8 meter GI pole with double arm bracket (1m) for illumination of volley ball court using 8M height Pole made of in combination of hot dip galvanised mild steel pipe sections 114mm dia. & 89mm dia. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(80 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedestal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.The pole shall be able to with stand a wind velocity of 180km/hour. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint . The cost is inclusive of making RCC  Foundation and erection charges with special T&P, for street Light pole duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.45Mtr x 0.45Mtrs x1.20 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. and earthling of light poles and laying, glanding and termination of 4CX10 Sq.mm XLPE armoured aluminium cable in 63 mm· die (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe .lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. including excavation and backfilling of earth, cable terminations using double compression cable glands and cable lugs. All light poles shall be earthed to nearest earth pit using GI wire.

od103442/2019_2020 :   Supply of 3M height post top Pole Made of hot dip galvanised mild steel pipe section 114mm of 1000mm(L) & 76 mm dia of 2000mm(L) height along with Top Decoative Cast Iron Ring with weight of 3kgs . Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(80 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pedastal to be mounted on a steel base plate of 200x 200x10mm . This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.The pole shall be able to with stand wind velocity of 180 km/hour. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour as approved by client.The cost is incusive of providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. complete. and earthling of light poles and laying, glanding and termination of 4CX10 Sq.mm XLPE armoured aluminium cable in 63 mm· die (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe .lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. including excavation and backfilling of earth, cable terminations using double compression cable glands and cable lugs. All light poles shall be earthed to nearest earth pit using GI wire.

od103443/2019_2020 :  Supply of LED Post top luminaire 35W, electrical Class I, with a grey (RAL 7037) or as approved by the engineer in charge, painted high pressure die cast aluminium body, a canopy made of ASA (Acrylonitrile Styrene Acrylate), , high impact Acrylic protector (for optimal luminous flux & IK 08 impact resistance), highly efficient white reflector (for pleasant & glare free indirect light with symmetrical distribution), permanently sealed onto the body to achieve separate IP 66 optical & control gear compartments, suitable for vertical mounting of 60mm diameter. The luminaire shall have a CCT of 3000K and Colour Rendering Index >70, a driver (efficiency > 85%) with internal surge protection of 6 kV and external surge protection of 10 kV, Power Factor 0.95, a residual flux of 70% (L70) @ 50,000 hours at Ta 50 degree. The cost is inclusive of laying and termination of 3CX1.5 sq.mm FRLS flexible copper cable from junction box of light pole LED fixture.

od103444/2019_2020 : Focus lights for Stage & existing trees Spot Light, 8-10W,LED, 3000k, Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 65 protection,CRI > 70,voltage input AC100-240V.Body-Die-casting aluminium Body with Surface Anti-ageing electrostatic spray processing & screen (IK 08). Body colour as approved by Engineer in charge.Dimension-60mm(Dia.)x180mm(L)x107mm(W)x147mm(H),Weight-1.5kgs. Estimated Lifetime-L70 @ 50,000hours minimum. or equivalent. the cost is inclusive of making  Foundation and erection charges with special T&P, for Post top LED light duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. complete. Supply, laying in HDPE / DWC pipe, supply, glanding, termination and testing of 4 Core 4 sq.mm stranded power copper conductor stranded, XLPE insulated, cores laid up inner sheathed for multicore cables FRLS cable / armoured, extruded PVC type sheathed , 650/1100 volt grade as per IS 7098 ( part 1) 1988. The rate is inclusive of all materials required for glanding termination of cables for lighting work of spot lights

od103445/2019_2020 : Supply, Installation, testing and Commissioning of 3KWp grid connected Solar Roof system of all components such as solar panels,DC combainer box,DC DB,AC DB ,inverter ,AC cabling,DC cabling including all civil works @ south beach area as per technical specifications. The cost is inclusive of liasoning with KSEB and getting all necessary approval for feasibility and testing and commissioning of solar system. supply, installation and testing and commissioning of earth pit and earthling of solar system suing Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers. Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and earth pit chamber using HDPE and excavation and backfilling of earth. Separate earth pits shall be is used for AC , DC and LA system. The scope is inclusive of s supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm).The cost is inclusive of two year maintenance.The maintenance includes monthly cleaning of solar panel,LED light fixture,checking the functioning of solar panels,inverter ,surge protection etc ,tightening the terminal box in ACDB ,DCDB ,DCArray etc ,checking out DC output replacing of fuses ,surge protector ,MCB ,DC cabling ,AC cabling ,earthing etc complete

od103446/2019_2020 : Supply, Installation & Commissioning of 1 KW Solar tree structure made of Stainless steel plates as per technical specifications with 1 KW solar panels , Inverter, AC and DC cables Cables, DB Box & lithium battery for min 18 hours autonomy including other Accessories, Civil works & foundation. The cost is inclusive of liasoning with KSEB and getting all necessary approval for feasibility and testing and commissioning of solar system. supply, installation and testing and commissioning of earth pit and earthling of solar system suing Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers. Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and earth pit chamber using HDPE and excavation and backfilling of earth. Separate earth pits shall be is used for AC , DC and LA system. The scope is inclusive of s supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm).The cost is inclusive of two year maintenance.The maintenance includes monthly cleaning of solar panel,LED light fixture,checking the functioning of solar panels,inverter ,surge protection ,battery etc ,tightening the terminal box in ACDB ,DCDB ,DCArray etc ,checking out DC output replacing of fuses ,surge protector ,MCB ,DC cabling ,AC cabling ,earthing etc complete

od103447/2019_2020 :  Supplying and fixing 12 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthling etc. as required and with Supplying and fixing of four nos of 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in MCB DB complete with connections Supplying and fixing 40 A , double pole, 240 volts, isolator and Supplying and fixing 40 A, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. supply, installation and testing and commissioning of earth pit and earthling of solar system suing Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers. Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and copper wire and earth pit chamber using HDPE cover and excavation and backfilling of earth. The scope is inclusive of s supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm).

od103674/2019_2020 : LIGHTING CONTROL PANEL FOR GROUP CONTROL: Supplying, unloading at site, shifting to site, assembling, levelling, grouting, erecting, earthling Testing, & Commissioning of Street light Feeder Pillar boxes as per tender specification. The feeder pillar shall be for group control of LED street lights system with all hard wares for power, control and communication devices and required software. It Shall be a GPRS/GSM/ RF / LORA/ based remote street light monitoring system with capacity for self - protection from short circuit, over voltage and anti-theft alert, one contactor for each phase is to be provided. Device capability for scheduling the on/off timings of lighting control switchgears based on the available sun-rise and sunset. Special emergency on/off facility with wireless control. System capability to capture and provide all electrical parameters at variable time intervals and live data collection timings. Smart Energy meter with ISI marking accuracy class specified by KSEB for measuring energy consumption. It shall be able to Control minimum 50 nos. LED , 140-270Vac, CE/FCC certified communication module, On-board 2 nos. current (4-20mA), and 2 nos. analogue voltage channel(1-10V), On-board RS485 Modbus interface. supply, installation and testing and commissioning of earth pit and earthing of lighting control panel using Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers and earthing lighting control panel using Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and copper wire and earth pit chamber using HDPE cover and excavation and backfilling of earth and earthing using 25x5 mm copper flat complete in all respect . Supply andLaying, of 4CX10 sq.mm XLPE aluminium cable in 63/51 mm HDPE pipe from light poles to lighting control panel and glanding and termination of cable using double compression cable gland. Foundation and erection charges with special T&P, for Post top LED light duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. complete.

od103679/2019_2020 :  Providing and fixing heavy duty, double ball bearing and with sturdy mesh guard: aluminium alloy one piece of blade wall mounting oscillating type air circulator conforming to IS: 2997, including fixing with anchor bolts, regulator making connection testing etc. as required.400 mm sweep with three speed regulator. make fan shall be orient/Usha/almonard/ Crompton or equivalent.

od103684/2019_2020 : Supply and fixing and commissioning of 1HP Monobloc pump of make Kirloskar/ crompton/ Texmo or equivalent including L& T make or equivalent motor starter, 3CX4 sq.mm,1.1KV flexible copper wire ( approximately 20 meter) and all associated pipeline work including all pipes, fitting and consumables complete in all respect as directed by Engineer in Charge.

2.16 : Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

od103687/2019_2020 : Liasoning with KSEB for obtaining power supply

Civil works for Freedom struggle Museum

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.31 : Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.2.1 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.9.2 : Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.42 : Distempering with 1st quality acrylic distemper (ready mixed) of approvedmanufacturer, of required shade and colour complete, as per manufacturer'sspecification.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

14.43 : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.70 : Floor polishing on masonry or concrete floors with was polish of approved brand and manufacture .

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.1 : Providing and fixing to existing door frames.30 mm thick Glas Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS : 14856, including fixing to frames.

9.70.2 : Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm

9.74.3 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

9.77 : Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete

od101124/2019_2020 : Providing and fixing 40mm thick machine cut, rough flamed finish at top surface only, shell white colour Granite for stone seater/copping and similar locations, of size 60x30cm, laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, etc. complete at all levels.<br>Area of slab over 0.50 sqm

17.3.1 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.7 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap

17.70.2 : Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

50.18.7.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge 20 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

50.18.7.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

50.18.7.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.32.1 : Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

18.48 : Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

19.18.1 : Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.4.1 : Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.57.1 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per trees plants (for 100 nos.=427.45/100)

30.2.57.2 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Shrubs plants (for 200 nos.=427.45/200)

30.2.57.3 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Hedge plants (for 300 nos.=427.45/300)

12.48 : Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

10.16.2 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

od103698/2019_2020 : Removing and relaying existing cobble stones of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost.)<br>

od33572/2019_2020 : Providing and fixing 80x120x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 75mm thick compacted bed of 6mm aggregate, compacting and proper embedding/ laying of cobble stone into the aggregate bedding layer through vibratory compaction by using plate vibrator, filling the joints with m sand finishing and sweeping extra sand . complete as per direction of engineer-in-charge

od33573/2019_2020 : Providing and fixing 30x30x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 75mm thick compacted bed of 6mm aggregate, compacting and proper embedding/ laying of cobble stone into the aggregate bedding layer through vibratory compaction by using plate vibrator, filling the joints with m sand finishing and sweeping extra sand . complete as per direction of engineer-in-charge

Supplying and fixing in position rough finish blue granite stone decorative pillar of size 14 inches diameter of height up to 10 feet or nearest size including cost of , transportation charges and installation, labor charges.(Including loading and unloading charges

od33792/2019_2020 : 10236 Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot.: Rs 20<br>

od33793/2019_2020 : 10324 Plumeria alba of plants height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags: Rs 225<br>

od33794/2019_2020 : 10211 Furcaira variegated well developed with fresh & healthy foliage 8 to 10 leaves in 30 cm Earthen Pot: Rs 200<br>

od33795/2019_2020 : 10187 Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. plant in 25 cm size Earthen Pot/ Plastic Pot: Rs 450<br>

od33796/2019_2020 : 10079 Providing of Raphis palm plant, having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot / Plastic pot.: Rs 450<br>

od33797/2019_2020 : 10289 Ficus nuda of plants height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of plants size 25 cm: <br>

od33798/2019_2020 : 10040 Providing of Croton Duck foot (Elite) plant, having ht. 45 cm and above with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot.: <br>

od33799/2019_2020 : 10409 Supply and stacking of plant Tabernaemontana divaricata (Chandni double) of height 90-105 cm., bushy in big size HDPE bag: rs <br>

od33800/2019_2020 : 10289 Ficus nuda of plants height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of plants size 25 cm:<br>

od33801/2019_2020 : Providing of Croton Challanger variety plant, having ht. 30cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot / Plastic pot <br>

od106909/2019_2020 : Supplying and errecting in position Ferrocement water storage tank made from superior quality ferrocement work with 50 mm min wall thickness and ribbings as required etc complete

od106910/2019_2020 : Supplying and errecting in position Ferrocement readymade septic tank with superior quality ferrocement having min wall thickness 50 mm in cluding conveyance and errection charges

Electrical works for Freedom struggle Museum

od104699/2019_2020 : Supply, Installation, testing and commissioning 3M height post top Pole Made of hot dip galvanised mild steel pipe section 89mm dia. Arch. cast iron Base design starts with a bottom dia of 300mm & radially tapers to 143mm dia. for a height of 135mm, which is followed by rings of 123mm dia.x25mm(H) & 143mm dia.x50mm(H) , each 3nos. at alternate arrangement. Total weight of the base is 15 Kgs. & height of the base is 360mm. Decorative Top Ring-(weight- 3kgs.) is made of cast iron. All cast iron parts weight mentioned are with +/- 5% tolerance.Entire pole including all the cast iron elements shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(80 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedastal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour as approved by client. The cost is inclusive of making  foundation and erection with special T&P, for Post top LED light duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. complete. and earthling of light poles and laying, glanding and termination of 4CX10 Sq.mm XLPE armoured aluminium cable in 63 mm· dia (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe .lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. including excavation and backfilling of earth, cable terminations using double compression cable glands and cable lugs. All light poles shall be earthed to nearest earth pit using GI wire.

od104700/2019_2020 : Supply, erection, testing and commissioning 22 - 27 W , IP -66 Protected Post top luminaries on the existing bracket. Fixture made from powder coated single piece pressure diecast aluminium housing with heat dissipation in fins on housing with high power LEDs, Diffuser, glass cover ensuring IP 65 protection for lamp and control gear compartment, system lumen output of 100 lumens/W high power LED. The integrated driver shall be having high efficiency more than 85% an din compliance to IEC standards, system 5000 burning hours with 80 % initial lumens maintained. The fixture shall be CE compliance. The luminaire shall have a CCT of 3000K and Colour Rendering Index >70, a driver (efficiency > 85%) with internal surge protection of 6 kV and external surge protection of 10/10 kV, Power Factor 0.95, a residual flux of 70% (L80) @ 50,000 hours at Ta 50 degree. The cost is inclusive of laying and termination of 3CX1.5 sq.mm FRLS flexible copper cable from junction box of light pole LED fixture.

od104702/2019_2020 : Supply, installation, testing and commissioning of 8-10 W Focus lights for illuminating Stage & existing trees -Spot Light, 8-10W,LED, 3000k, Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 65 protection,CRI > 70,voltage input AC100-240V.Body-Die-casting aluminium Body with Surface Anti-ageing electrostatic spray processing & screen (IK 08). Body colour-RAL 9004 + RAL 9018 Matt or as approved by engineer in charge .Dimension-140mm(Dia.)x180mm(L)x152mm(W)x192mm(H), min Weight-2kgs. Estimated Lifetime-L70 @ 50,000hours minimum. Neri model no -Light NSL-12S or equivalent. The cost is inclusive of making  Foundation and erection charges with special T&P, for Post top LED light duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. complete. Supply, laying in HDPE / DWC pipe, supply, glanding, termination and testing of 4 Core 4 sq.mm stranded power copper conductor stranded, XLPE insulated, cores laid up inner sheathed for multicore cables FRLS cable / armoured, extruded PVC type sheathed , 650/1100 volt grade as per IS 7098 ( part 1) 1988. The rate is inclusive of all materials required for glanding termination of cables for lighting work of focus lights

od104704/2019_2020 :  Supply, installation, testing and commissioning of 9 W LED floor lights made up of pressure Die cast aluminium alloy with corrosion resistance with low copper content. Hard Chrome plated stainless steel 316 grade front ring, silicon gasket, stainless steel screws & clear toughed glass of 8mm thickness with static load resistance >2500 kgs. Operating input voltage 150 - 270 volts, 50 Hz, pf > 0.9 , CCT = 3000 deg K. The cost is inlusive of supply, glanding, termination and testing of 4 Core 4 sq.mm stranded power copper conductor stranded, XLPE insulated, cores laid up inner sheathed for multicore cables FRLS cable / armoured, extruded PVC type sheathed , 650/1100 volt grade as per IS 7098 ( part 1) 1988.

od104705/2019_2020 : Supply of all wiring materials and Wiring up of light points,fan points/ exhaust fan point and plug points in cell rooms, toilets, wall lights and security room using 1.5 sq.mm/2.5 and 4 sq.mm FRLS copper wires, GI box, moular plates, switches, sockets as per CPWD latest specifications.  Supplying and fixing 12 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthling etc. as required and with Supplying and fixing of four nos of 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in MCB DB complete with connections Supplying and fixing 40 A , double pole, 240 volts, isolator and Supplying and fixing 40 A, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. supply, installation and testing and commissioning of earth pit and earthling of solar system suing Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers. Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and copper wire and earth pit chamber using HDPE cover and excavation and backfilling of earth. The scope is inclusive of s supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm). The cable shall be laid in 300x50x1.6 mm GI Cable tray and neatly dressed with cable ties.

od104706/2019_2020 : LIGHTING CONTROL PANEL FOR GROUP CONTROL: Supplying, unloading at site, shifting to site, assembling, levelling, grouting, erecting, earthling Testing, & Commissioning of Street light Feeder Pillar boxes as per tender specification. The feeder pillar shall be for group control of LED street lights system with all hard wares for power, control and communication devices and required software. It Shall be a GPRS/GSM/ RF / LORA/ based remote street light monitoring system with capacity for self - protection from short circuit, over voltage and anti-theft alert, one contactor for each phase is to be provided. Device capability for scheduling the on/off timings of lighting control switchgears based on the available sun-rise and sunset. Special emergency on/off facility with wireless control. System capability to capture and provide all electrical parameters at variable time intervals and live data collection timings. Smart Energy meter with ISI marking accuracy class specified by KSEB for measuring energy consumption. It shall be able to Control minimum 50 nos. LED , 140-270Vac, CE/FCC certified communication module, On-board 2 nos. current (4-20mA), and 2 nos. analogue voltage channel(1-10V), On-board RS485 Modbus interface. supply, installation and testing and commissioning of earth pit and earthling of solar system suing Nickel coated Copper bonded electrode made from low carbon steel. Earth rods and molecularly bonded with 99.9 % pure electrolytic copper with 250 micron coating, 17.2 mm dia with pressed contact including stainless steel nut, bolts and washers. Laying, of 4CX10 sq.mm XLPE aluminium cable in 63/51 mm HDPE pipe from light poles to lighting control panel and glanding and termination of cable using double compression cable gland and earthling lighting control panel using Copper bonded rod of size (17.2mmx3000mm) with 1 nos chemical bag of 40 kg. with all accessories. Approximate weight of copper electrode is 5.62 kg and copper wire and earth pit chamber using HDPE cover and excavation and backfilling of earth and earthling using 25x5 mm copper flat complete in all respect.. Foundation and erection charges with special T&P, for Post top LED light duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.30Mtr x 0.30Mtrs x.90 MT size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement and curing for 7 days as directed by the field engineers during execution including excavation of Earth/BT all labour charges and cost and conveyance of materials etc. The cables to lighting control panel shall be laid in 300x50x1.6mm GI cable tray and cables shall be neatly dressed using cable ties. complete.

od104712/2019_2020 :  Providing and fixing heavy duty, double ball bearing and with sturdy mesh guard: aluminium alloy one piece of blade wall mounting oscillating type air circulator conforming to IS: 2997, including fixing with anchor bolts, regulator making connection testing etc. as required.400 mm sweep with three speed regulator. make fan shall be orient/Usha/almonard/ Crompton or equivalent.

od104713/2019_2020 :  Supply and fixing and commissioning of 1HP Monobloc pump of make Kirloskar/ crompton/ Texmo or equivalent including L& T make motor starter, 3CX4 sq.mm ,1.1 KV flexible copper wire ( approximately 20 meter) and all associated pipeline work including all pipes, fitting and consumables complete in all respect as directed by Engineer in Charge.

od104714/2019_2020 : Supply, installation, testing and commissioning of 15" (380 mm )heavy duty exhaust fan with double ball bearing complete and with petty material for connection and lovers. Make Havells/ Usha/Bajaj/ almonard

2.16 : Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

od104722/2019_2020 : Supply, installation, testing and commissioning of 15 W indoor down lighter surface mounted LED luminaire Model philips make catalogue SM 251 C LED 15 S-6500 PSU WH or equivalent. Wipro/Crompton/ Bajaj or as approved.

O&M Civil

od147176/2019_2020 : Complete maintenance of the entire yard cleaning the entire interlocking/pavement tile area, as per direction of officer in charge including complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, hedge, flower beds, foliages, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge including Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel & other T & P material/articles shall be provided by the contractor.) cleaning the entire iterlocking/pavemnt tile rea, providing new pavement tile where old tile is damaged etc and as per direction of officer in charge.For first year

od147193/2019_2020 : Complete maintenance of the entire yard cleaning the entire interlocking/pavement tile area, as per direction of officer in charge including complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, hedge, flower beds, foliages, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge including Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel & other T & P material/articles shall be provided by the contractor.) cleaning the entire iterlocking/pavemnt tile rea, providing new pavement tile where old tile is damaged etc and as per direction of officer in charge.For second year

od147199/2019_2020 : Complete maintenance of the entire yard cleaning the entire interlocking/pavement tile area, as per direction of officer in charge including complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, hedge, flower beds, foliages, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge including Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel & other T & P material/articles shall be provided by the contractor.) cleaning the entire iterlocking/pavemnt tile rea, providing new pavement tile where old tile is damaged etc and as per direction of officer in charge.For third year

O&M electrical

od147357/2019_2020 : Supplying of 4Cx10 sq.mm XLPE insulated, aluminium conductor cable of 1.1 KV grade complete in all respects as desired by Engineer In charge

od152553/2019_2020 : Supplying of 3Cx2.5sq.mm XLPE insulated, aluminium conductor cable of 1.1 KV grade complete in all respects as desired by Engineer In charge

od152681/2019_2020 : Supply ,installation testing and commissioning of ploy carbonate rectangular type weather proof junction box with dimension 310x230x145mm suitable for outdoor installation with IP66 protection

od152682/2019_2020 : Supply,installation,testing and commissioning of 10A terminal block, DIN Rail suitable for connecting up to 10sqmm Aluminium cable (6nos)with lateral marker slots

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

14.1 : Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.

od152876/2019_2020 : Operation and Maintenance of solar tree for third year. The maintenance includes monthly cleaning of solar panel,LED light fixture,checking the functioning of solar panels,inverter ,surge protection ,battery etc ,tightening the terminal box in ACDB ,DCDB ,DCArray etc ,checking out DC output replacing of fuses ,surge protector ,MCB ,DC cabling ,AC cabling ,earthing etc complete including all civil work..

od152888/2019_2020 : Operation and Maintenance of solar roof system for third year. The maintenance includes monthly cleaning of solar panel,LED light fixture,checking the functioning of solar panels,inverter ,surge protection etc. ,tightening the terminal blocks in AC DB ,DC DB ,DC Array etc. ,checking out DC output replacing of fuses ,surge protector ,MCB ,DC cabling ,AC cabling ,earthing etc. complete including civil work.

od153069/2019_2020 : Maintenance of street lights, street lights poles, post tops poles , LED fixtures, lighting control panels and making ready light fixtures for illumination including supply of required spares like lamps, lamp holder, cables, fuses, MCBs, cable lugs, ferrule, surge protectors, junction boxes and all consumables etc. The work also includes periodic cleaning ( minimum once in two months ) of light fixtures, poles and control panels etc.. First year

od153169/2019_2020 : Maintenance of street lights, street lights poles, post tops poles , LED fixtures, lighting control panels and making ready light fixtures for illumination including supply of required spares like lamps, lamp holder, cables, fuses, MCBs, cable lugs, ferrule, surge protectors, junction boxes and all consumables etc. The work also includes periodic cleaning ( minimum once in two months ) of light fixtures, poles and control panels etc.. Second year

od153171/2019_2020 : Maintenance of street lights, street lights poles, post tops poles , LED fixtures, lighting control panels and making ready light fixtures for illumination including supply of required spares like lamps, lamp holder, cables, fuses, MCBs, cable lugs, ferrule, surge protectors, junction boxes and all consumables etc. The work also includes period cleaning of light fixtures , poles and control panels ( Minimum once in two months) etc.. Third year

Gym Equipments

Supply and fixing of STEEL SWINGS -Metal :- All tubular steel 0f 2.5mm thickness are galvanized and zinc dipped. The support legs are made from 60mm galvanised steel. The horizontal beam is manufactured from 89mm diameter galvanised steel. The swing bearings are made of stainless steel. The coloured panels are made from a 13mm thick compact material (HPL). Robust in construction, it offers excellent resistance to weathering and vandalism. The swing seats are made of shock absorbing moulded honeycomb rubber. The swing chains are made of stainless steel. The seat fixing brackets are made of 10mm stainless steel wire. PVC sliding rings are fitted to limit the wear of the metal parts over time. The rings are accessed by a vandal proof, stainless steel shackle. The fixings are made of stainless or plated steel and protected by anti-vandalism polyamide caps. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & Fixing of STEEL SLIDES - Metal: The sliding surface is made of stainless steel 2mm thick, which are shaped, bent and rolled from one piece. The coloured panels are made from a 13mm thick compact material (HPL). Robust in construction, it offers excellent resistance to weathering and vandalism. The tubes are made of stainless steel, diameter 40mm, guaranteeing lasting durability and reliability of the equipment. The platforms are made from a textured and non-slip compact material (HPL), 12.5mm thick. The fixings are made of stainless or plated steel and protected by anti-vandalism polyamide caps. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & Fixing of STEEL SEE SAW - Metal: Tubes made of 90x90mm galvanised steel square shape, ensuring robustness and durability. The seats are made from a 13mm thick compact material (HPL). Robust in construction, it offers excellent resistance to weathering and vandalism. The springs are made from Grade 35SCD6 steel, shot blasted, stress relieved, zinc coated and finished with two coats of epoxy polyester powder. Proludic have patented an exceptionally strong and secure polyamide fixing for the spring, ensuring a long product life. The handles are made of galvanised, painted steel. The stainless steel fixings are protected by polyamide anti-vandalism caps. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & Installation of Hydraulic Butterfly- The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The seat and back support are made from a polyurethane compound, providing a soft and ergonomic surface for the user, similar to those found in gym settings. The elements conform to the SGS TB117 fire test requirements. The handles are made from elasticated EDPM, offering both durability and fire resistance. The material retains both its shape and feel across a wide temperature range -55°C à 120°C. The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The hydraulic oil piston is made up of elements manufactured from chrome, aluminium and stainless steel. Users can adjust the resistance from just a few kilogrammes up to as much as 60kg on certain machines. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & Installation of Hydraulic Stepper- The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The foot supports are made from low density roto-moulded polyethylene (LDPE). This material has been chosen both for its hard wearing properties and its resistance to ultra violet rays. The supports have a textured finish in order to provide grip and reduce the appearance of scuff marks. The handles are made from elasticated EDPM, offering both durability and fire resistance. The material retains both its shape and feel across a wide temperature range -55°C à 120°C. The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The hydraulic oil piston is made up of elements manufactured from chrome, aluminium and stainless steel. Users can adjust the resistance from just a few kilogrammes up to as much as 60kg on certain machines. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & Installtion of Elliptical Trainer - The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The handles are made from elasticated EDPM, offering both durability and fire resistance. The material retains both its shape and feel across a wide temperature range -55°C à 120°C.The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The foot supports are made from low density roto-moulded polyethylene (LDPE). This material has been chosen both for its hard wearing properties and its resistance to ultra violet rays. The supports have a textured finish in order to provide grip and reduce the appearance of scuff marks. The discs are made of painted steel. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & installation of AIRWALKER - The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The handles are made from elasticated EDPM, offering both durability and fire resistance. The material retains both its shape and feel across a wide temperature range -55°C à 120°C. The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The foot supports are made from low density roto-moulded polyethylene (LDPE). This material has been chosen both for its hard wearing properties and its resistance to ultra violet rays. The supports have a textured finish in order to provide grip and reduce the appearance of scuff marks. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & installation of Hydraulic Rowing Machine (Legs) -The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The seat and back support are made from a polyurethane compound, providing a soft and ergonomic surface for the user, similar to those found in gym settings. The elements conform to the SGS TB117 fire test requirements. The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The hydraulic oil piston is made up of elements manufactured from chrome, aluminium and stainless steel. Users can adjust the resistance from just a few kilogrammes up to as much as 60kg on certain machines.. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & installation of Shoulder Wheel The disc is made of painted steel. The rate is including the cost of concrete footing , anchor bolt etc complete.

Supply & installation of Spinning Bike - The framework of the workstations is made from 3.5 to 4mm thick, hot-dipped galvanised steel, protected by a polyester powder coated finish. This treatment provides high levels of durability, notably in coastal locations. The seat is made from a polyurethane compound, providing a soft and ergonomic surface for the user, similar to those found in gym settings. The element conform to the SGS TB117 fire test requirements. The handles are made from elasticated EDPM, offering both durability and fire resistance. The material retains both its shape and feel across a wide temperature range -55°C à 120°C. The stainless steel waterproof bearing has been subjected to tests involving over 10,000 hours of constant use. The rate is including the cost of concrete footing , anchor bolt etc complete.