SPECIAL REPAIR TO BLDG NO. T 306 IN ZONE N AND PROVN OF CERTAIN MINOR WORK AT MIL STN AGARTALA

Amount

Schedule'A' Part-I: B&R works

Dismantling of AC sheet corrugated / CGI corrugated sheets in roofing any gauge and any thickness including ridge, valley/gutter etc.

Dismantling wall / ceiling board (fibre pulp insulation) or insulation boards any thickness including cover fillets

Dismantling timber boarding of any description fixed in any position.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work built in cement mortar.

Taking down chowkats or frames but with shutters (without taking off shutters from the frames) n.exc 1 sqm each.

Taking down cement plaster on brick concrete surfaces including racking out joints hacking for key, scrubbing down with, water etc.

Hacking out old broken glass ( any thickness, sizes, quality or description) from wooden frames or glazed with putty or fixed with beads

S&F sheet glass of 4 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm but in frosted.

S&F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with 'L' type or 'J' type or cranked book bolts and washers, in roofs, walls etc

S&F 0.63 mm plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed)

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified.

Excavation in post holes each n exc 0.5 cum getting out returning filling in and removing earth or broken rubble mixed with earth around in layers not exc 25 cm watering and removing surplus soil to a distance not exc 50 m and making good surface as in soft/loose soil.

M&L cement concrete in foundation filling and mass concrete type C-2 1:3:6 (40 mm graded stone aggregate)

S&F Fe-410-W(Gde-E-250) quality-B roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle,chanel or flat sections) including distance pieces, cleats etc.

Cutting holes in to brick wall for inserting hold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, exe half brick but not exe 1 brick.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay complete all as directed.

M&L mild steel work such as grills, guard bars etc and similar work conforming to Fe290 GDE E-165

M & L complete removal of internal wall finishes by scrapping down and preparation of plastered or unplastered surfaces by applying 3mm wall care putty and applying two coats of oil bound distemper over a coat of primer on old/new plastered surfaces .

M&L applying two coats of weather coat on old / new plastered surfaces of wall over a coat of primer after applying a thin layer of wall care putty including removal of existing treatment and preparation of old or new plastered surfaces to receive paint complete all as specified and directed .

S&F exposed GI powder coated snap grid frame for false ceiling 600 x 600 mm size of wall angle 25 x 25 x 0.35 mm size of cross sec 24 x 38 x 0.70 mm with 2 mm dia GI suspender including supply and fixing of 4 mm thick E board in false ceiling fixing arrangement from steel tress any type of truss finished with two coats of washable distemper over a coat of cement prime on exposed surfaces all as specified (make: Everest or equivalent as approved by GE/AGE (I)).

M&L for Two coats of synthetic enamelled paint over coat of red oxide zinc chrome on steel surfaces over 10cm width or girth including preparation of new surfaces.

M&L for Two coats of synthetic enamelled paint over coat of red oxide zinc chrome on steel surfaces n.exc 10cm width or girth including preparation of old painted surfaces.

M & L for Painting in wooden surfaces with two coats synthetic enamel paint over a coat of pink primer incl preparations of new painted surfaces over 10 cm width or girth.

Material & Labour 20 mm thick screed bed or bedding layer of mortar in cm 1:4 for laying floor tiles

Material & Labour 10mm thick screed bed to wall in cm (1:4)

M&L light shade vitrified ceramic coloured tiles 10 mm thick (square /rectangular) polished, area of each tile not exceeding 0.36 sqm in floors etc, set & jointed in neat cement slurry & pointed with white or coloured cement to match all as specified and directed.

M&L light shade vitrified ceramic coloured tiles 10 mm thick (square /rectangular) polished, area of each tile not exceeding 0.36 sqm in skirting etc, set & jointed in neat cement slurry & pointed with white or coloured cement to match all as specified and directed.

M&L 15mm thick rendering in cm (1:3) on brick or concrete surfaces with integral water proofing compound @ 3% by wt of cement,(Note : Water Proofing compound measured & paid separately) finished even and fair.

Supply only integral water proofing compound

M&L brick work with sub class 'b' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6

M&L Brick work with sub class B bricks straight or curved on plan to any radius in half brick thick walls, built in cm 1:4

Material and labour PCC 1:3:6 type C2 using 40 mm graded aggregate as in plinth protection 75 mm thick finished fair and even w/o using extra cement.

Material and labour PCC 1:3:6 type C2 using 40 mm graded aggregate as in surface channel/drain complete all as specified and directed.

M&L 40 mm thick plain cement conc type B1 (1:2:4) using 20mm graded aggregate as in bed of drain .

Material and labour Extra for form fair finished drain on channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitred stopped end etc complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30 cm ditto

S&F 2nd class Hard wood 20 mm thick boarding planed both side with butt joints fixed with nails in any situation

Material & Labour for writing letters or figures (block, Roman, Italic or Indian) n.exc.30 cm high complete all as specified and directed.

Schedule'A' Part-II: E&M works

Taking down carefully aluminium/ copper point wiring (light, fan, socket or power) complete (excluding sunken box) including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and segregating serviceable fittings & set aside for reuse in the work and making good to disturbed surfaces of walls, floors, ceilings etc. complete all as specified and as directed.

Taking down unserviceable sub main wiring of any type and any size including wooden batten, PVC conduit or casing capping complete all as specified and as directed.

Material & Labour for point wiring for One light /fan point controlled by one way one switch complete with cable PVC insulated, unsheathed, 1100V grade conforming to IS for one way SP, 5A with 1.5 Sqmm of cable of nominal area multistranded copper conductor (FRLSH)drawn through and including 20mm PVC casing capping including accessories on wall/floor/ceiling ( on surface) etc with 16G MS pressed steel terminal box with 2.8 mm thick laminated sheet cover for mounting switch, socket outlet etc complete with all accessories/fittings including PVC insulated continuous multi stranded copper earth wire (1.5 Sqmm) (FRLSH) and connected to common earth dolly complete all as specified and as directed.

All as per Item No. 44 above but one 3 Pin 5/6 Amp socket outlet on independent board.

All as per Item No. 44 above one 3 Pin 5/6 Amp socket outlet on same board with other switches.

All as per Item No. 44 above but point wiring with 2.5 Sqmm stranded PVC un sheathed copper conductor for one 3 Pin 15/16 amps socket outlet on independent board including continuous earth wire with 1.5 Sqmm stranded PVC unsheathed copper conductor and connected to common earth dolly.

Material and labour for sub main wiring using two single core PVC insulated, PVC sheathed stranded copper conductor (FRLS) cable of size 4 Sq mm unsheathed drawn in and including PVC capping casing including accessories in surface to wall/floor/ceiling etc and 1.5 Sq mm PVC insulated unsheathed copper conductor as continuous earth continuity conductor drawn in complete all as directed and specified.

Material and labour switch piano flush type 5/6 Amps single pole one way complete all as specified and as directed.

Material and labour Switch socket combination, 3/5 pin, 5/6 Amp flush type complete all as specified and as directed.

Material and labour Switch socket combination 2 in 1, 3 Pin, 5/6 Amp and 15/16 Amp flush type universal complete all as specified and as directed.

Supply & fixing stepped type electronics fan regulator on the existing phenolic laminated sheet etc complete all as specified and as directed.

Supply & fixing Ceiling rose 3 Terminal/PVC/ Polycarbonate, isolated body complete all as specified and as directed.

Material and labour sheet metal enclosure for double door DBs using MCB with 200 Amps rated bus/link bar of 8 way 240V including taking down unserviceable one.

S&F MCB TPN 63 Amps 415 Volt 'C' Curve, 10 KA Make : Indoasian or equivalent make of Havells/HPL.

Supply and fixing MCB SPN 6 to 32 Amps 230 Volt 'C' Curve, 10 KA Make : Indoasian or equivalent make of Havells/HPL.

Supply and fixing MCB SP 6 to 32 Amps 230 Volt 'C' Curve, 10 KA Make : Indoasian or equivalent make of Havells/HPL.

Material and labour single pole and Neutral enclosure with a two pin and earth plug and socket 15 Amp complete with one single pole MCB 20 Amps including taking down old one complete all as directed and specified.

Supply & fix LED light fitting 1x22 watt(4 ft) IP>=20, class-I,, CRI>=80, CT>=5700 K, surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with industrial grade heavy duty driver having THD<10% including all accessories connecting of flexible wire twin/three core from ceiling rose to fitting in flexible conduit all as specified and directed. Make- Havells, Model- ENDURALINEARNEOBS22WLED865SPCWH equivalent approved make of CG/Philips/ Bajaj/Jaquar

Supply & fix LED Bulb 12 watt, Ball lamp, (Pin type), 230V, PF not less than 0.85 (min),1000 Lumen output incl . Make- Havells cat part No NU BULB PLUS 12 W 865 B22 2 STAR or equivalent approved make of CG/Bajaj/ Philips/Jaquar

Supply & fix LED Bulk Head 10 watt, comprising of pressure die cast housing with acrylic diffuser (IP65 protection). Make- Jaquar, Model- LBLK01X010XC or equivalent approved make of CG/Bajaj/ Philips/Jaquar

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron wire of size 4 mm dia as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover made of RCC (1:1.5:3) type A1 duly reinforced with 8mm dia TMT bar @150 c/c both ways, one lifting handle made of 10mm dia TMT bar embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15cm thick complete all as specified and directed.

Taking down carefully old unserviceable Ceiling fan/Exhaust fan/Wall mounted fan of any sizes from site for safe custody for refixing.

Hanging or Refixing of Ceiling Fan/Exhaust fan/Wall mounted fan any size including provision of suitable flexible cable as required from ceiling rose or connector to fan complete all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor of 16 sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, twin core cable flat complete all as specified and directed.

Supply Installation, testing and commission Refrigerators 4 star rated inverter frost free double door type having capacity 28/310 Ltr including testing of equipment complete all as specified and directed. Make: SAMSUNG/LG/GODREJ/Whirlpool.

M/s Amrit Gope

M/S PAUL ENTERPRISE

SHRI CHANDAN CHANDA

M/S PRITAM ENTERPRISES

Pranjit kar