Supplying and providing of Equipment / Instruments for up-gradation of the Water Quality Laboratory (Level plus plus and above) at Data Centre, Water Resources Department, Porvorim Goa.

Amount

Providing, Installing, Testing and Commissioning of the “BENCHTOP CONDUCTIVITY METER” having following specification: i. Conductivity probe, K= 0.1 ii. Conductivity Range: 0.001 μS to 199.9 mS iii. TDS Range: 0.001 to 200.0 ppt iv. Salinity Type: Practical salinity or natural sea water having range: 0.00 ~ 4.04% (NaCl), 0.05 to 42.40(PSS: Sea water salinity) v. Suitable Conductivity standards vi. With attached Electrode stand and holder The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc.,complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and commissioning of the“pH METER” with glass body having following specifications; i. Open pore pH electrode, ATC Probe integral electrode holder and 100/240 ii. pH Range: 0.00 to 14.00 pH VAC Adapter, iii. Resolution: 0.01 pH The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc.,complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “BIO-SAFETY CABINET, CLASS II TYPE “having following specification i. Vertical and Ultra-Low ii. Particulate Air (ULPA) filter iii. Class II - Type A2 Open iv. Size (min): 4' X 2' X2' v. Material : GI Powder Coated The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc.,complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “COD DIGESTOR” having following specifications; i. Pre-programmed heating blocks of standard parameters for routine digestions such as COD, TOC, total nitrogen, total phosphorus, and metals. ii. Temperature range: 40–160 °C (1 °C increments) Warm up time: From 20 °C to 160 °C within 10 minutes The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge

Providing, Installing, Testing and Commissioning of the“Global Positioning System” (GPS)having following specifications; i. Accuracy & Satellite System: ±3m & GPS ii. Screen Type: Color, 65K Color iii. Display Size: 1.4" x 1.7" (3.5 x 4.4 cm); 2.2" diagonal (5.6 cm) The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the“WATER VELOCITY AND FLOW METER”having following specifications; i. Usage Type: Spot ii. Measurement technology: Electro-magnetic iii. Parameters measured: Flow velocity and water depth. iv. Measurement range: 0 - 6 m/s v. Accuracy at 0 - 3 m/s: ±2 % of meas. value ±0.015 m/s&Accuracy at 0 - 5 m/s: ±4 % of meas. value ±0.015 m/s Zero stability: ±0.015 m/s The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the“ULTRASONIC WATERBATH” having following specifications; i. Capacity: 4.5ltr ii. Ultrasonic Power: 120Watts iii. Tank Size (L x W x H)(mm): 300 x 155 x 100 The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “WATER BATH”havingfollowing specifications; i. Double walled construction. ii. Outer body made of mild steel painted with powder coating. iii. Inner chamber made of thick S/Steel compete with concentric rings. iv. Temperature control ler v. Size (L x B x H): 330 x 300 x 100 mm (9 holes 75 mm diam) Provision for PID temp. Controller. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Testing and Commissioning of the “STOPWATCH”having following specifications; i. Stopwatch 1/100 second ii. Time Display: Hour, Minute and Seconds iii. Calendar Display: Day, Date & Month iv. Alarm The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Testing and Commissioning of the “STANDARD WEIGHT BOX”having following specifications; i. Class E2 stainless steel for testing & calibration. ii. Range: 0 - 200gms (23 Pcs) iii. Certified by NABL 17025 accreditation laboratories with NIST traceability. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Testing and Commissioning of the “EKMAN DREDGE” having following specifications; i. Quick collection of sediment samples from various water bodies. ii. Material: Stainless Steel 316 grade. iii. Description: Ekman dredge with case, 6" x 6" x 6" sample area & 12” x 12” x12” " sample area. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Testing and Commissioning of the “HOT PLATE”havingfollowing specifications; i. Rectangular heating plate with Body made of mild steel duly powder coated. Top plate of stainless steel. ii. Temp. Controller Digital microprocessor based with thermocouple which can be inserted in the material. Stirrer RPM 1400 controlled by steeples regulator. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “MULTIPARAMETER WATER QUALITY TESTING UNIT”having following specifications; i. Measure pH, Temperature, ORP (Oxidation Reduction Potential), Dissolved Oxygen, Conductivity, Salinity, Total Dissolved Solids (TDS), Resistivity, Turbidity, Depth and Total Suspended Solids. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the“FUME HOOD”having following specifications; i. Thick, wooden board fabricated, designed to suck out all toxic/harmful vapors. ii. Suction Capacity: Silent 650 CFM iii. Face Velocity: min. 0.5m/s (100 fpm) iv. Sweep Size: 120 mm/min. v. RPM@ 230 V: 1050 vi. Air Delivery: min 100 m3/hr vii. Should be fitted with fluorescent light and a gas cock for gas/air supply. Working Size: W = 4' x L = 6' x H = 5' The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “MEMBRANE FILTRATION ASSEMBLY” having following specifications; i. Filter flaskBorosil Bottle minimum 1 liter capacity, filtration glass funnel with Aluminium Clamp, ii. One Neoprene cover and Cork Capacity- 250 ml (FFG47) iii. One pack Membrane Filter - C. N. 47 mm/0.45 µm pack of 100. (Cat no - 160047X) iv. One Vacuum pump diaphragm type-oil free. (Cat no - V-300) Pump capacity: min. 1.0 hp The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioning of the “METROHM BURETTE“having following specifications; i. Metrohm 876 Dosimat Plus ii. Dispensing unit for liquid handling in laboratories iii. Microprocessor control, for titrating and dosing operations, The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Testing and Commissioning of the “THERMOMETER”having following specifications; i. Range: 0-300°C ii. Accuracy: 0.1 deg C The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing and Commissioningof the “AUTO DISPENSER” having following specifications; i. Single stroke dispensing of lyes, acids (H2SO4, HCL, HNO3, HF, Per-Chloric acid, Phosphoric acid, etc), bases, aqueous liquids or solvents. ii. Bench top dispenser, mechanical. iii. Volume range: 0.2 to 100 ml. The instrument/ equipment supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing, Commissioning & Training of the “ICP-MS SPECTROMETER” with Auto Sampler including Microwave Digestion Unit having following specifications; CP-MS with Auto Sampler: toanalyzethe metals at trace levels in water (surfacewater, groundwater&wastewater) with software controlled aerosol (argon) dilutionalong with the supply of ; · 1000 ppm NIST Certified Multi element (at least 23 elements)aqueous calibration standard (100 ml). · Fume hood with accessories. · 20 KVA UPS with 30 min Backup · Argon Gas Cylinder –3no’s · Helium Gas Cylinder – 1no. · Reaction Gas Cylinder as required · Gas Regulator for all the gases mentioned above – 1 no. each · Computer · Auto sampler Training Microwave digestion unit: Microwave Power output: Minimum 1000 (1800) Watt or better with microprocessor controlled dual magnetron system. Controller: Color touch screen display with real-time graphical representation of reaction parameters and display of internal temperature of every individual reaction. External controllers not acceptable. The ICP-MS system should be supplied with all peripherals. The instruments/ equipments supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing, Commissioning & Training of the “GAS CHROMATOGRAPH-MASS SPECTROMETER (GC-MS)” having following specifications Gas Chromatograph: · Microprocessor based Fast GC with AFC/EPC/ PPC and able to support 3 injectors, 3 detectors. · GC must have a touchscreen display with Graphical User Interface (GUI) with self-diagnostics tools · Split/Splitless injector port –1 Nos Liquid Auto Injector Automated Liquid Auto sampler with 150 Vials capacity Triple Quadruple Mass Spectrometer: · System should have dual filament design with automatic switching for EI. · Ion Source temperature: upto 350°C · Electron energy range upto 200eV or better · Should have Automatic leak check, Visualize remaining time for stabilization of vacuum and Automatic tuning judgement features · EI MRM Sensitivity (S/N): 17,500:1 for 100 fg/μl of OFN for the transition of m/z 272 → 222 or better. · Instrument detection limit (IDL): ≤ 4 fg with 10 fg/μl OFN for the transition of m/z 272 → 222 or better Software: · Suitable software for performing data analyses, calibration, blank correction, data import, export, handling and reporting · Must have built-in reporting functionality to generate industry-standard reports with the ability to customize report templates as necessary · Automatically create SIM from acquired Scan data and optimizing tool for SIM group creation with dwell time for better repeatability and peak profile The instruments/ equipments supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

Providing, Installing, Testing, Commissioning & Training of ““Laboratory Information Management Systems (LIMS), including related additional hardware””having following specifications; LIMS Software is required to manage the entire laboratory processes from sample collection to final reporting in environmental testing laboratory. It should have the ability to improve efficiency, increase cost saving and maintain compliance with a configurable and expandable system capable of supporting the Laboratory Data Management requirement including managing the data from all laboratory instrument/equipment as applicable. It shall comply with ISO 17025: 2017 and National Environmental Laboratory Accreditation Conference (NELAC). · LIMS should include; · Min. No of users: 15 users · Min. No of samples : 50/day · Desktop Workstation Qty 15NOS · Laptop((HP/Dell/Lenovo or equivalent) · Quantity: 9 Nos. · LaserPrinter(Color)(hp, Brother, Canon, or equivalent) with additional set of Cartridges · Quantity: 7 Nos. cloud Server 1No · Additional Antivirus software (McAfee, Bit defender, Norton or equivalent) for 5 years. · Quantity: Nos. to cover each individual desktop and laptops provided. The instruments/ equipments supplied shall be as per the detailed specifications Annexed and of the approved make of relevant standards applicable etc., complete and as directed by the Engineer- In-charge.

RAJA KUMAR KURRA