Proposed Construction of NamSankirtanSabhagruha Auditorium for Pandharpur Municipal Council at Reservation Non 53, C .S. NO 4075 A 1

Amount

EXCAVATION, FILLING AND SOLING

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.)By Mechanical Means Spec. No.: Bd.A.1 Page No. 259

Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated materials upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum ramming, watering etc. complete. (Lift upto 1.5m).Spec. No.: Bd.A.6 Page No. 260

Filling in plinth and floors with approved excavated materials in 15 cm to 20 cm layers including watering and compaction complete. Spec. No.: Bd.A.10 Page No. 262

Filling in plinth and floors with contractors soil sand or murum in 15 cm to 20cm, layers including watering and compaction complete. Spec. No.: Bd.A.11 Page No. 263

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting complete. Spec. No.: Bd.A. 12 Page No. 264

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation clorophyriphoas/lendene at the rate of 5 litres of emulsion concentrates of 0.5 percent of Aldrin per square meter of surface area covering 10 years guarantee. Spec : As directed by Engineer In Charge

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 0.5 percent of Hephoclore per square metre of surface area covering ten years guarantee. Spec : As directed by Engineer In Charge

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 percent of Clorophysiphas/ 20 E.C. Hephoclore at the rate of 7.5 litres emulsion concentrate per hole and sealing the same with proper filling & covering 10 years guarantee. Spec : As directed by Engineer In Charge

Shifting excavated & existing soil including loading in truck and conveying to dumping point approved by pandharpur council, unloading, spreading etc. complete. With all leads and lifts.

CEMENT CONCRETE ( PLAIN & REINFORCED)

Providing and laying in situ, cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, compacting and curing complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer With crushed sand. Spec. No.: Bd. E. 1 Page No. 287

Providing and laying in situ cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, cover blocks compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) complete, With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer.. With Crushed sand. Spec. No.: Bd.F.3 Page No. 298 and B.7, Page No.38

Providing and casting in situ cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement).With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer.With Crushed sand. Spec. No.: Bd.F.5 Page No. 300 and B.7, Page.No. 38

Providing & casting in situ cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs & drawings or as directed including centering, formwork, cover blocks compaction & roughening the surface if special finish is to be provided & curing complete. (Excluding reinforcement).With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer. With Crushed sand. Spec. No.: Bd.F.6 Page No. 300 and B.7, Page No.38

Providing and casting in situ cement concrete M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. slabs and landings canopy, waist slab with steps as per detailed designs and drawings including centering, formwork, cover blocks compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement).With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer. With Crushed sand. Spec. No.: Bd.F.8 Page No. 302 and B.7, Page No.38.

Providing & casting in situ cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design & drawings including centering, formwork, cover blocks compacting & roughening the surface if special finish is to be provided & curing complete. (Excluding reinforcement).With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer With Crushed sand. Spec. No.: Bd.F.9 Page No. 303 and B.7, Page No.38

Providing and casting in situ cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. pardi 75mm thick fins including centering, formwork, cover blocks compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement). With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer With Crushed Sand. Spec. No.: Bd.F.11 Page No. 304 and B.7, Page No. 38

Providing, cutting, bending, hooking, tieing in position and laying TMT FE 500 steel bar for reinforcement as per detailed drawings for all R.C.C. works. Spec : BR.35 Page No. 134

MASONRY WORK ( STONE AND BRICK )

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water, striking joints on un exposed faces and watering complete. Spec.No.:Bd.H.1PageNo.329

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water, striking joints on unexposed faces, raking out joints on exposed faces and watering Complete. Spec.No.:Bd.G.1PageNo.313

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, racking out joints, watering and scaffolding Complete. Spec.No.:Bd.G.5PageNo.315

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering Complete. Spec.No.:Bd.G.7PageNo.316

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) Spec : As directed by engineer in charge

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) Spec : As directed by engineer in charge

STONE WORK NEWASA STONE WORK

Providing & fixing Newasa stone Ashlar / sadguru ghadai masonary in of 150 mm thk in size & 275 x175 in cement morar 1:3 for composite masonary. Install stone member in plumb level & in aligment provide through stone at interval & necessary accessaoris like clips , bars,clamps or necessary are required for errction & stone masanary to supporting back brick wall & back up material. Use pigment in mortor for grouting of colour match to natural stone, watering & cleaning etc complete as per as directed by Engineer in charge .)

Providing & fixing Newasa stone of 75 MM thkness in sadguru ghadai for 300 MM tread & riser with fixing method as per details drawings in 1: 3 cement mortor with watering curing complete as directed by Engineer in charge .

Providing & fixing cladding to columns & beam surface in Newasa stone of 100 mm thk in size of 275 x175 mm in cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete..Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .) (sadguru ghadai)

Providing & fixing cladding to round vertical coloumns in Newasa stone of 75 mm thk in size of 275 x175 mm as per design & detials shown in drwaings cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete..Use pigment in mortor for grouting or colour match to natural stone watering etc complete as per as directed by Engineer in charge .) (sadguru ghadai)

STONE WORK DHOLPUR STONE

Providing & fixing composite masonary in Dholpur stone of 100 mm thk in size of 275 x175 in cement morar 1:6 with 230 mm thk brick wall as back wall in super sturcture in first class .Providing first class Burnt Brick masonry with conventional / I.S. type bricks in cement mortar 1:4 including scaffolding, racking out joints pointing in C.M. 1:3 and watering in pillars of rectangular or square shape as shown on the drawing or as directed complete. Spec.No.:Bd.G.9(a)PageNo.317(Install stone member in plumb level & in aligment provide through stone at interval & necessary accessaoris like clips , bars,clamps or necessary are required for errction & stone masonary to supporting back wall & back up material ..Use pigment in mortor for grouting or colour match no natural stone watering etc complete as per as directed by Engineer in charge .)

Providing & fixing cladding to vertical surfaces in Dholpur Stone of 75 mm thk in size of 275 x175 mm as per design & detials shown in drwaings in cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete.Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .)

Providing & fixing Arches of various sizes in 150 mm thk .Dholpur stone as per design a details drawings in 1:3 cement mortor with necessary accessaries & adhesive for fixing & erection ..Use pigment in mortor for grouting or colour match to natural stone watering etc complete as per as directed by Engineer in charge .)

Providing & fixing Railing in total Dholpur stone as per details & design drawings necessary accessaries & adhesive for fixing & erection .Use pigment in mortor for grouting or colour match no natural stone watering etc complete as per as directed by Engineer in charge .)

Providing & fixing Dome kalash of different sizes in Dholpur stone as per detail design on top of curved surfaces etc complete.as per as directed by Engineer in charge .) Small size

Providing & fixing Dome kalash of different sizes in Dholpur stone as per detail design on top of curved surfaces etc complete.as per as directed by Engineer in charge .) Big size

Providing & fixing Mandir with lintel, sill/ vertical posts/small brackets of various sizes in Dholpur stone as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)

STONE WORK RED AGRA STONE

Providing & fixing 20 MM THK Red-agra Stone cladding for sloping chajja on m.s. frame structure as per details & drwings in 1:3 morter/adhesive for joints & also on R.C.C surfaces as per directed by Engineer in charge .)

Providing & fixing Full round bands of 100 thk in Red Agra stone as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)

Providing & fixing brackets in Red Agra of 100 mm thk of various sizes as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .) Small size

Providing & fixing brackets in Red Agra of 100 mm thk of various sizes as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .) Big size

Providing & fixing ornamental elements as a frame to window ( W ) with lintel, sill/ vertical posts/small brackets of various sizes in Red Agra as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)

Providing & fixing Arches of various sizes in 150 mm thk Red agra as per design a details drawings in 1:3 cement mortor with necessary accessaries & adhesive for fixing & erection ..Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .)

GFRC & PRECAST WORK GFRC

Providing & fixing a glass fiber reinforced concrete jali for screening as per design with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .)

Providing & fixing top of kalash Of various size & design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .) MAIN DOME 800MM

Providing & fixing top of kalash Of various size & design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .) MEDIUM DOME 500MM

Providing & fixing top of kalash Of various size & design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .) SMALL DOME 300MM

Providing & fixing parapet band size & design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .)

Providing & fixing kalash Petal design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .)

FERROCRETE

Providing, cutting, bending, bindingas per desired shape, armature reinforcement as per design drawing for ferrocement double skin skin elements for both the outer and inner layer separately, providing and fixing with overlaps as recommended welded and hexagonal meshes on both the layers on both sides as per detailed drawing, Providing, cutting, bending binding, as per desired shape, armature reinforcement for stiffening ribs as per design drawing for ferrocement ribs, sandwiching 40 mm thk high density Thermocol sheets betweeeen two layers of meshes, mixing and mortaring the mortar mix as per detailed mix given with 43 grade OPC and suggested additives, finishing from both sides, maintaining desired line and level where required, curing using hessian cloth and continuours watering as per detailed specifications and work procedure etc complete.

Providing, cutting, bending, bindingas per desired shape, armature reinforcement as per design drawing for ferrocement single skin elements , providing and fixing with overlaps as recommended welded and hexagonal meshes on both sides as per detailed drawing, Providing, cutting, bending binding, as per desired shape, armature reinforcement for stiffening ribs as per design drawing for ferrocement ribs, mixing and mortaring the mortar mix as per detailed mix given with 43 grade OPC and suggested additives, finishing from both sides, maintaining desired line and level where required, curing using hessian cloth and continuours watering as per detailed specifications and work procedure etc complete.

FERROCRETE

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document. Window W5

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document. Window (W1

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document. Brackets large

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document. Brackets small

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document. sloping Chajja

Providing & fabricating pre-cast concrete units in Portland cement Gray Coarse/fine Aggregate Air Entraining admixture, steel standard mix design curing & strength 15 MPA minimum at 28 days. Fabricate units complying with quality control & dimensional tolerances accurate moulds mortar tight & of sufficient strength to withstand pressure due to concrete placing operations provide exposed surface finish specified by Architect detail specifications & Installation method we separately enclosed in tender document.Kalash

PLASTERING AND FINISHING

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing complete. Spec. No.: Bd. L.2 Page No. 368

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.: Bd.L.7 Page No. 369

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing complete. Spec. No.: Bd. L.10, Page No.370

Providing and fixing chicken mesh jali (24 gauge) at the junction of 2 different surfaces of different material component at the time of plastering to prevent cracking in plaster surface as and where directed at all floors with all leads and lifts etc. complete. Spec. No.: As directed by Engineer in Charge:

Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.** Spec. No.: As directed by Engineer in charge.

WATER PROOFING WORK

Providing & laying water proof treatment of terrace slab with B.B. Coba in all position with an average thickness of 112 mm consisting specialised materials as per the manufactures specifications and covering 10 years guarantee on court fee stamp paper including all lead, lift, etc. complete. Spec. No.: As directed by Engineer in charge.

Providing water proof bedding for flooring of Bath and W.C. 25 mm thick in C.M.1:3 including using 1 kg of water proof compound per bag of cement including leveling curing etc. complete. Spec. No.: As directed by Engineer in charge.

Providing and laying jointless Polydee-LM/Dr.fixit / Chemestic and alike a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP-42/ Dr.fixit and alike Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM/ Dr.fixit and alike @ 700 gms/sqm and applying 2nd coat of Polydee-LM/ Dr.fixit and alike @ 700 gms/sqm and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/sqm to be paid in separate item.) covering 7 years guarantee on Stamp Paper of Rs. 500/- etc. complete. Spec. No.: As directed by Engineer in charge

Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete). Spec. No.: Bd.J.2 Page No. 355

FLOORING, SKIRTING AND DADO

Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing complete.** Spec. No.: Bd. M-3 page No. 380^Note- Water absorption for item No,19 should not exceed 0.05%**Note** – For item no. 14 to 33 Prior approval of S.E. will be necessary.. Spec : As directed by Engineer-In- Charge

Providing and laying cement concrete flooring 50mm thick with M15 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30 cm x 30 cm or other size laid diagonally /square etc finishing smooth (with extra cement) in any colour as directed and curing complete. With Natural Sand Spec. No.: Bd.M.6 Page No. 381

Providing and laying in position flooring of flame finish black granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.** Spec. No.: Bd.M. 3 B/Page No. 380

Providing and fixing machine cut machine polished 18 mm to 20 mm thick flame finish black granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1;4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.** Spec. No.: Bd. M.22 B/Page No. 390

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.** Spec. No.: Bd.M. 3 B/Page No. 380

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1;4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.** Spec. No.: Bd. M.22 B/Page No. 390

Providing and laying in position inlay work in flooring of granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.** Spec. No.: Bd.M. 3 B/Page No. 380

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with rounding the edges etc. complete . **A) Both side polish Spec. No.: Bd.M.35 /Page No.393

Providing and laying vitrified matt fininsh tiles of RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete^.**a) flooring Spec. No.: Bd.M.12 Page No. 385

Providing and laying vitrified matt finish tiles of RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning complete.^**b) Skirting Spec. No.: Bd.M.12 Page No. 385

Providing and laying Antiskid Ceramic tiles of approved quality of company RAK / Kajaria / Nitco / Asian or equivalent make of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing complete. ** Spec. No.: Bd. M-12

Providing and laying ceramic tiles of RAK/ Kajaria / Nitco /Asian or equivalent make having size 30 cm. x 45 cm. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing complete. Spec. No.: Bd.M.13 Page No. 386.

Providing and laying telephone black / Amba White / Cadburybrown / RBI red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. ** Specifications: Bd. M. 12

Providing & Fixing Kitchen Otta shall be Pre Polished Granite top and Nirali Make stainless steel Kitchen, sink of size 400 x 550mm. The width of the Kitchen Otta & front fascia shall be as per drawing. Granite slab of sufficient dimensions to cover stainless sink area and nahani trap below it shall be provided. Supporting system shall be 25 mm thick kadappa slabs in double layers for Vertical supports and 35 mm thick Kadappa Slab below granite top. The working drawing of the Kitchen Otta shall be got approved from Engineer-in- charge if required the fixing shall be done by resin adhesive for the fascia. Item including curing ,cleaning, edge polishing, nosing, chamfering, groove making etc complete. The stainless sink shall be of the best quality available in the market with the I.S.I. Mark. Note- Mode of mesurement only top area consider.

Providing & Fixing Wash basin counter shall be Pre Polished Granite top. Granite slab of sufficient dimensions to cover stainless sink area and nahani trap below it shall be provided. Supporting system shall be 25 mm thick kadappa slabs in double layers for Vertical supports and 35 mm thick Kadappa Slab below granite top. The working drawing of the Wash basin counter shall be got approved from Engineer-in- charge if required the fixing shall be done by resin adhesive for the fascia. Item including curing ,cleaning, edge polishing, nosing, chamfering, groove making etc complete. Note- Mode of mesurement only top area consider

DOORS, WINDOWS AND VENTILATORS , RAILING

Providing & fixing French door with three panel fired in T.W. frame of 125x75 MM thk All rails in 12mm thk double ply & both side 6mm ply with laminate finish. Both panels are in 12 MM thk double ply with laminate finish as per detail drawings. With all necessary fixtures fittings & polishing etc. complete approved by Architect. FD1

Providing & fixing in position French door of s panels with teak wood frame of 150 x 100 mm with all rails of 12 mm thk. Double ply & both side 6mm ply with laminate finish with 10 mm thk. M.S.square bars from outside & 8mm thk plain glass from Inside lower panel with 12mm thk double ply & laminate finish from both side as per detail drawings with necessary fittings & fixtures etc. complete FD2

1. Providing & fixing in French door of panels with teakwood frame of size 125x75mm thk. With all rails of 12 mm thk. Double ply & both side 6mm ply with laminate finish with 10 mm thk. M.S.square bars from outside & 8mm thk plain glass from Inside lower panel with 12mm thk double ply & laminate finish from both side as per detail drawings with necessary fittings & fixtures etc. complete. FD3

Providing & fixing Double leaf shutter in 125 x 75 MM thk. teak wood frame with style of 12 mm thk Double ply & 6mm th ply on top & both side laminate finish. Glass of 8mm thk fixed in 12 mm teak moulding & panel of 12 MM + 12mm thk panels & fixed in teak moulding as per drawing with all necessary fixtures etc. complete. D2

Providing & fixing double leaf shutter in 18mm thk double ply frame with lipping 35 mm thk solid core flush door laminate finish on both side & 8mm thk clear glass fixed 8mm thk lipping in 12mm thk teak wood molding as per the detailed drawings with all necessary fixtures etc. Complete. D3 .D5

Providing & fixing 35mm thk solid core flush door with 18mm thk Double frame with lipping. Laminate finish of approved color with glazing of 8mm thk Clear glass fixed with 8mm thk lipping with grooves as per design & detail drawings with stainless steel fixtures etc. complete. D4

Providing & fixing single leaf 35mm thk Solid core flush door with laminate finish both side fixed in 18mm thk double ply frame finish in laminate & 12mm lipping on the face. & 18mm thk. Teak wood lipping fixed on shutter as per detail drawing with all necessary fixtures & fitting, polishing etc. complete D6

Providing & fixing 35mm thk Solid core flush door with both side laminate & 12mm thk teakwood moulding with 8mm thk Glass fixed in 8mm lipping with both side 3mm glass film S.S.brush metal handle & Aldrop etc. complete as per detailed drawings. D7

Providing & fixing solid core marine ply flush door 35mm thk With PVC coating on all sides in single leaf/Double leaf with glass 8mm thk fixed in 8mm thk Lipping with both side 3mm glass film with necessary S.S.fixtures etc. Complete. D7A

Providing & fixing double leaf shutter of 35mm thk solid core flush door with laminate finish both side fixed in 18mm thk Double ply frame with laminate finish & 8 mm thk lipping for exposed with 8mm thk Clear glass fixed in 8mm lipping, 12mm thk teakwood. molding to be fixed as per detail drawings. with all necessary fixture, fittings polishing etc. complete D9 ,D8

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass with all required screws and nuts etc, complete. With powder coating withoutbox. Spec : As directed by Engineer In Charge

Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineer-in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete, With powder coating without box. Spec : As directed by Engineer In Charge

Providing and fixing in position alluminium openable window of any size as per detailed drawing and as directed by Engineer-in-charg`e with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete. b) With powder coating Spec : As directed by Engineer In Charge Note – While arriving at the rate of item weight at 6.90 kg / Sqm is considered

Providing and fixing in position alluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer-in-charge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. b) With powder coating Spec : As directed by Engineer In Charge Note – While arriving at the rate of item weight at 6.90 kg / Sqm is considered

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38mm x 1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg./sq.m. as per drawing including fixtures, necessary welding & painting with one coats of anticorrosive paint & two coats of oil painting complete. Spec. No.: Bd.U.1 Page No. 537

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 6248-1979) (With mechanical gear) Spec. No.: Bd.T.55, Page No. 510

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.2m center to center and 3 pipes of 12mm diameter fixed horizontally including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge **Note**—For item no. 58 to 60 prior approval of Superintending Engineer will be required

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 10mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge

PAINTING WORKS

Providing and applying 2 coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) complete. Spec. No.: Bd.0.7 Page No. 406

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required. Spec : As directed by Engineer In Charge

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec : As directed by Engineer In Charge

Providing and applying JOTUN PAINT first coatis water proofing, flexible, thick exterior emu. Coating. second coait is Local dolpur stone texture & covering unevenness and small cracks in the concrete. final coat is Jotashield ColourXtreme has weather resistant grade of TiO2 with special IR reflecting pigment that offers supreme SRI that offers upto 18-20% drop in surface temperature and upto 5 degree reduction of interior temperature.

Providing and applying two coats of appex Appex Ace white exterior paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary , and watering the surface for two days complete. Spec : As directed by Engineer In Charge

STRUCTURAL WORK & ROOF

Providing, hoisting and fixing in position mild steel (GRADE-310)Tubular Trusses of required span as per drawing and design including purlins, wind bracing, runners, gusset plates foundations bolts including painting three coats of oil paint approved quality and shade, scaffolding etc. complete as per ISI specifications. Spec. No.: B-18 Page No. 78 (TRUSS, RAILING, DUCT FINCE)

Providing structural steel work (GRADE-250) in single stanchions com-posed of R.S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two coats of oil painting etc. complete Spec. No.: Bd.C.6 Page No. 277 BRACING

Providing structural steel work (GRADE-250) in single stanchions com-posed of R.S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two coats of oil painting etc. complete Spec. No.: Bd.C.6 Page No. 277 CATWALK

Providing structural steel work (GRADE-250) in single stanchions com-posed of R.S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two coats of oil painting etc. complete Spec. No.: Bd.C.6 Page No. 277 STAGE MANDAPI

Providing structural steel work (GRADE-250) in single stanchions com-posed of R.S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two coats of oil painting etc. complete Spec. No.: Bd.C.6 Page No. 277 DUCT CLOSING & WALKWAY ALL INCLUSIVE

Providing and fixing of colour coated Zinc aluminium (R) AZ150 (min 150 gms/sq.mt. total on each side) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45mm Base Metal Thickness (BMT) (0.5mm TCT), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminiumm 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyster paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center-to-center. The end rib shall be designed for anti-capacity groove. & return leg. The feed material should have coil manufacturers product details marked a regular interval. including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 kg/sqm) 601 mm to 900 mm girth (Surface Width). Spec :As directed by Engineer in charge.

Rockwool as a insulating material sandwitched between metacolour sheet . Of density 65kg/cum, make Rockwool india / UP Twiga.

Providing & fixing poly corbonate roof sheet 10 mm thickness (Brand Lexan Make, Colour Clear Sabin)to close toilet duct as per design and drawing Including, self-drilling screw, etc. complete.

Providing and fixing false ceiling of 12mm thick tubular Acoustic Armstrong/ Everest/ AMS boards of approved make, shape and sizes as per drawings including powder coated G.I. wall angle of 20mm x 20mm size, G.I. grid runners of size 20mm x 38mm at 600mm center to center both ways and suspended using G.I. wire 3mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete. Spec : Bd. R. 19 Page No. 462

Providing and fixing frame work of galvanised iron for suspended false ceiling which includes galvanised iron perimeter channels of size 27 mm & 0.5 mm thick having one flange of 20 mm and another of 30 mm along with perimeter of the ceiling, fixing in brick wall / partition with the help of rawal plugs and screws, suspending galvenised iron intermediate channels of size 45 mm and 0.9 mm thick with two flanges of 15 mm each from the soffit at 1200 mm centers with steel galvanised iron hanger of width 25 mm x 0.5 mm fasteners, ceiling section of 0.5 mm thickness having curved wedge of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 450 mmcenters, 12.5 mm dry walls screws at 230 mmcenters; fixing screws mechanically either with screw driver or drilling machine with suitable attachmentetc. complete. Spec :As directed by Engineer in charge.

Providing and fixing false ceiling of teak wood particle board half perforated sheet 12 mm thick including scaffolding, if necessary, all iron work and two coats of oil painting to boards and beading i.e. visible surface (excluding frame work and runners). Spec : Bd. R. 17 Page No. 461

Providing & fixing 6 mm thk texured shera wood plank 1200 x 150 mm fixed with screw to 12 mm thk waterproof marine ply base recommaneded company . ( excluding frame work & runners ref dsr item 13/17 BDR )

Providing & fixing elevator/ lift of make prescribed in the make list with machine roomless & gearless technology, automatic rescue device, 10 persons capacity (Please refer Schindler product discription ) 3 STOP

Providing & fixing elevator/ lift of make prescribed in the make list with machine roomless & gearless technology, automatic rescue device, 10 persons capacity (Please refer Schindler product discription ) 2 STOP

ABSTRACT SHEET FOR INTERNAL PLUMBING WORK

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. spec. No.: BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing 10 cm PVC nahani trap with grating etc. complete. Spec. No.: BD.V 32 A page 551 and as directed by Engineer in charge

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm of Nirali or equivalent make incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.** Spec : As directed by Engineer In Charge

Providing and fixing C.P. Angular stop clock with wall flange jaquar make continental (CAT.NO. CON-059) including necessary sockets/union nut etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing C.P.Two way BIB cock jaquar make continental (CAT.NO. CON- 041) including necessary sockets/union nut etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe & wall flange jaquar or equivalent make continental (CAT.NO. CON-273 UPR ) including necessary sockets/union nut etc. complete.** Spec. No.: As directed by Engineer in charge

Providing and fixing C.P. sink cock with raised J shaped swinging casted spout jaquar or equivalent make continental (CAT.NO. CON -359) including necessary sockets/ union nut etc. complete.** Spec. No.: As directed by Engineer in charge

Providing and fixing C.P. BIB cock with wall flange jaquar or equivalent make continental (CAT.NO.ON-047) including necessary ockets/ union nut etc. complete.**Spec. No.: As directed by Engineer in charge

Providing and fixing C.P. Health Faucet jaquar or equivalent make continental (CAT.NO. ALD IVY 573) including necessary sockets/union nut etc. complete.** Spec. No.: As directed by Engineer in charge

Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black backlite seat with all necessary pipe connection etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing coloured glazed earthenware Wash Hand Basin of 63 cm x 45 cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Spec. No.: Bd.V.30 Page No. 565

Providing and fixing Over Head Shower (CAT.NO. OHS - 1709) including necessary pipe connection up to the outside face of the wall. Spec : As directed by Engineer In Charge

Providing and fixing coloured glazed earthenware lipped flat back/corner type urinal with PVC 5 liters flushing cistern with fittings,capacity with fittings, inlet pipe and stop tap, brackets for fixing the cistern, P.V.C. flush pipe with fittings including lead soil pipe, lead trap and soil pipe connection up to the outside face of the wall. Spec. No.: Bd.V.26 Page No. 564

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing on walls/ ceiling / floors, ISI mark of below diameter ASTM uPVC SCHEDULE 80 pipes with screwed sockets & brackets, joints and necessary fittings such as socket's back nuts, elbows, bends, tees, reducers, plugs, clamps etc. including necessary drilling holes in walls, slabs, beam etc. and remaking good the demolished portion to restore the same in original condition neatly, testing etc. complete. (Prior approval of sample and brand by Executive Engineer is necessary before use).

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing and fixing of below dia PVC Ball Valve of approved make including necessary sockets / unions, nut, testing etc. complete. (Prior approval of sample and brand by Ex. Engineer is necessary before use)

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing and fixing of below 20 mm dia Non Return Valve of approved make including necessary sockets / unions, nut, testing etc. complete. (Prior approval of sample and brand by Ex. Engineer is necessary before use)

Providing, laying & fixing P.V.C. pipe of 40mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Spec : As directed by Engineer In Charge

Providing, laying & fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Spec : As directed by Engineer In Charge

Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. com-plete. Spec : As directed by Engineer In Charge

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. com-plete. Spec : As directed by Engineer In Charge

Providing and laying cast iron pipes of B class of 80mm diameter with sockets and spigot ends/ flanges and cast centrifugally/ vertically including specials, laying pipes and back filling the trench complete including excavation. Spec. No.: Bd.V.1 Page No. 547

Providing and laying cast iron pipes of B class of 100mm diameter with sockets and spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes and back filling the trench complete including excavation. Spec. No.: Bd.V.1 Page No. 547

Providing, laying & fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Spec : As directed by Engineer In Charge

Providing and Fixing 110 mm diameter PVC Rain Water pipe with necessary fittings such as bends, tees, single junctions, slotted vent, clamps etc complete Spec : As directed by Engineer In Charge

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets & necessary fittings and tested as per municipal requirements etc. complete. Spec : As directed by Engineer In Charge

ABSTRACT SHEET FOR EXTERNAL PLUMBING WORK Pumping Machinary - UGT To OHT

Supplying and erecting submersible pumpset of required HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell, suitable for 250 to 700 LPM discharge at 55 to 25 m head & (max efficiency at 40 m head & 400 Ipm discharge & delivery pipe of necessary diameter with a necessary H. type clamp. As per specification o. WP-SMP

Supplying & erecting Water lavel controller 230/ 415V AC., Four way for under ground & Over head tank operation .

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5- 10 HP consisting of DOL starter having relay range 13-21 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof encloser with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase inbalence etc ( Similar to LT model no.MU G10 / CAT NO. SS95983 )

Supplying and erecting 100mm dia. gun metal sluice valve at position with necessary materials.

Supplying and erecting Non return valve 100mm dia in position made of gun metal.

Supplying and erecting 0-100 lb/sq. inch pressure gauge having 4" dia complete with socket for 1/2" G.I. pipe.

Rising Mains (UGT to OHT)

Providing and fixing on walls/ ceiling / floors, ISI mark of below diameter ASTM uPVC SCHEDULE 80 pipes with screwed sockets & brackets, joints and necessary fittings such as socket's back nuts, elbows, bends, tees, reducers, plugs, clamps etc. including necessary drilling holes in walls, slabs, beam etc. and remaking good the demolished portion to restore the same in original condition neatly, testing etc. complete. (Prior approval of sample and brand by Executive Engineer is necessary before use).NON DSR

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Providing and fixing of below dia PVC Ball Valve of approved make including necessary sockets / unions, nut, testing etc. complete. (Prior approval of sample and brand by Ex. Engineer is necessary before use) NON DSR

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Excavation for foundation in hard murum including removing the excavated materials upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m)By Mechanical Means Spec. No.: Bd.A.2 Page No. 259

Filling in plinth and floors with contractors soil sand or murum in 15cm to 20cm, layers including watering and compaction complete. Spec. No.: Bd.A.11 Page No. 263

External Drainage System

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. Spec. No.: Bd.V.38, Page No. 572

Providing & constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574

Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574

Providing and constructing on sewer, B.B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm brick work in CM 1:4 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channel in smooth rendering, providing C.I.dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia.etc. complete as directed by Engineerin-charge.

Providing and constructing on sewer, B.B. masonry circular manhole concentric cone 1.5 M dia. at bottom and 0.5 M dia. at top and upto a depth of 5.00 M with 23 cm brick work, upto depth of 2 M from top and 35 cm thick brick work for balance depth in CM 1:4 proportion with 20 mm thick smooth plaster on both sides in CM 1:2 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. etc. complete as directed by Engineerin- charge.

External Stormwater System

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573

Providing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, including all taxes (Central and local), inspection charges, transport to departmental stores / site, unloading and stacking, etc. complete.(IS-458/1988)

450mm dia

Excavation for foundation in hard murum including removing the excavated materials upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m)By Mechanical Means Spec. No.: Bd.A.2 Page No. 259

Filling in plinth and floors with contractors soil sand or murum in 15cm to 20cm, layers including watering and compaction complete. Spec. No.: Bd.A.11 Page No. 263

Providing & constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574

Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574

Providing and constructing on sewer, B.B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm brick work in CM 1:4 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channel in smooth rendering, providing C.I.dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia.etc. complete as directed by Engineerin-charge.

Providing and constructing on sewer, B.B. masonry circular manhole concentric cone 1.5 M dia. at bottom and 0.5 M dia. at top and upto a depth of 5.00 M with 23 cm brick work, upto depth of 2 M from top and 35 cm thick brick work for balance depth in CM 1:4 proportion with 20 mm thick smooth plaster on both sides in CM 1:2 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. etc. complete as directed by Engineerin- charge.

ABSTRACT SHEET FOR FIRE WORK

PUMPHOUSE EQUIPMENTS SUPPLY

Supplying and installing, testing, perfect aligning and proper leveling and commissioning of fire service main pump, of 1800 LPM (Litres/min.) at 76 m head centrifugal type single stage pump, 50 HP, (37 kW) or of suitable HP as per specification No. FF-MFP/SSC

Supplying installing, testing, commissioning of Jockey Pump of 240 LPM at 56 m head, 3 ph. 440 A.C.15 HP, (11 kW) or of suitable HP with suitable Stages as per specification No. FF-MFP/JP

Control Panel + cabling in the pumphosue

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 200 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing 200 mm dia end line strainer for +ve suction as per specification No. FF-VL/ELS

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing double flange Ball type NRV of size 150 mm dia as per specification No. FF-VL/NRV

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in an approved manner as per specification No. FF-FFA/PG

Supplying and installing DANFOSS make pressure switch with 12/15 mm Ø isolation valve, G.I. nipple, elbow etc. in an approved manner as per specification No. FF-FFA/PS

Supplying and installing Air Vessel of 300 mm Ø 1.5m in height M.S. tank installed inside pump house as per specification No. FF-FFA/ACT

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

EXTERNAL HYDRANT SYSTEM SUPPLY

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing gun metal SS single outlet hydrant valve fitted with necessary accessories complete as per specification No. FF-VL/HV

Supplying fire fighting C.P. (controlled percolation) Hose pipe, 63mm dia, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/CPH

Supplying SS branch Pipe 63 mm Ø fitted with 20 mm dia detachable hexagonal nozzle as per specifications No. FF-FFA/NEW

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

Supplying and installing fire brigade Header of 150 mm Ø, for supplying water in fire tank as per specification No. FF-FA/FBC

Supplying and installing fire brigade Header (Siamese Connection) of 150 mm Ø for supplying water to wet riser system as per specification No. FF-FFA/SMC

INTERNAL HYDRANT SYSTEM SUPPLY

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing double flange Ball type NRV of size 150 mm dia as per specification No. FF-VL/NRV

Booster Pump of 900 LPM at average 40 m Head, 12.5 HP either Monoblock or of suitable HP with suitable Stages.

Supplying and installing gun metal SS single outlet hydrant valve fitted with necessary accessories complete as per specification No. FF-VL/HV

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 x 400 x 400mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m high pressure polypropylene (Polyhose) long fitted with necessary accessories complete as per specification No. FF-FFA/HV

Supplying SS branch Pipe 63 mm Ø fitted with 20 mm dia detachable hexagonal nozzle as per specifications No. FF-FFA/NEW

Supplying and erecting one no. Brass orifice plate having 6 mm. thickness, 140 mm outer dia of 140 mm at every single outlet hydrant valve as per specification No. FF-FFA/OP

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

SPRINKLER SYSTEM SUPPLY

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings as per specification no. FF-PP

Supplying and erecting 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction as per specification No. FF-SPR

Supplying & erecting vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of 75/80 mm dia having following features 1) Visual Switch Activation 2) Rugged Switch Assembly 3) Heavy Duty Alluminium pipe Saddles 4) Durable Metal Encloser 5) Steel U Bolts For Secure Mounting 6) Two SPDT ( Single Pole Double Track ) Synchronised Switches 7) Serviceable Without Draining Pipes

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

Supplying & Installing cast iron double flange butterfly valve of size 100 mm dia. as per specification No. FF-VL/BFV

Supplying & Installing cast iron double flange butterfly valve of size 75/80 mm dia. as per specification No. FF-VL/BFV

EXTINGUISHERS SUPPLY

ABC Type 6 kg with indicating gauge

Fire Buckets of 9 lit. water capacity filled with sand with stand at D.G. & Transformer Yard .

PUMPHOUSE EQUIPMENTS INSTALLATION

Supplying and installing, testing, perfect aligning and proper leveling and commissioning of fire service main pump, of 1800 LPM (Litres/min.) at 76 m head centrifugal type single stage pump, 50 HP, (37 kW) or of suitable HP as per specification No. FF-MFP/SSC

Supplying installing, testing, commissioning of Jockey Pump of 240 LPM at 56 m head, 3 ph. 440 A.C.15 HP, (11 kW) or of suitable HP with suitable Stages as per specification No. FF-MFP/JP

Control Panel + cabling in the pumphosue

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 200 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing 200 mm dia end line strainer for +ve suction as per specification No. FF-VL/ELS

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing double flange Ball type NRV of size 150 mm dia as per specification No. FF-VL/NRV

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in an approved manner as per specification No. FF-FFA/PG

Supplying and installing DANFOSS make pressure switch with 12/15 mm Ø isolation valve, G.I. nipple, elbow etc. in an approved manner as per specification No. FF-FFA/PS

Supplying and installing Air Vessel of 300 mm Ø 1.5m in height M.S. tank installed inside pump house as per specification No. FF-FFA/ACT

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

EXTERNAL HYDRANT SYSTEM INSTALLATION

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing gun metal SS single outlet hydrant valve fitted with necessary accessories complete as per specification No. FF-VL/HV

Supplying fire fighting C.P. (controlled percolation) Hose pipe, 63mm dia, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/CPH

Supplying SS branch Pipe 63 mm Ø fitted with 20 mm dia detachable hexagonal nozzle as per specifications No. FF-FFA/NEW

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

Supplying and installing fire brigade Header of 150 mm Ø, for supplying water in fire tank as per specification No. FF-FA/FBC

Supplying and installing fire brigade Header (Siamese Connection) of 150 mm Ø for supplying water to wet riser system as per specification No. FF-FFA/SMC

INTERNAL HYDRANT SYSTEM INSTALLATION

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No. FF-VL/BFV

Supplying and installing double flange Ball type NRV of size 150 mm dia as per specification No. FF-VL/NRV

Booster Pump of 900 LPM at average 40 m Head, 12.5 HP either Monoblock or of suitable HP with suitable Stages.

Supplying and installing gun metal SS single outlet hydrant valve fitted with necessary accessories complete as per specification No. FF-VL/HV

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 x 400 x 400mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m high pressure polypropylene (Polyhose) long fitted with necessary accessories complete as per specification No. FF-FFA/HV

Supplying SS branch Pipe 63 mm Ø fitted with 20 mm dia detachable hexagonal nozzle as per specifications No. FF-FFA/NEW

Supplying and erecting one no. Brass orifice plate having 6 mm. thickness, 140 mm outer dia of 140 mm at every single outlet hydrant valve as per specification No. FF-FFA/OP

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

SPRINKLER SYSTEM INSTALLATION

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings as per specification no. FF-PP

Supplying and erecting 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction as per specification No. FF-SPR

Supplying & erecting vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of 75/80 mm dia having following features 1) Visual Switch Activation 2) Rugged Switch Assembly 3) Heavy Duty Alluminium pipe Saddles 4) Durable Metal Encloser 5) Steel U Bolts For Secure Mounting 6) Two SPDT ( Single Pole Double Track ) Synchronised Switches 7) Serviceable Without Draining Pipes

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No. FF-FFA/ARV

Supplying & Installing cast iron double flange butterfly valve of size 100 mm dia. as per specification No. FF-VL/BFV

Supplying & Installing cast iron double flange butterfly valve of size 75/80 mm dia. as per specification No. FF-VL/BFV

EXTINGUISHERS INSTALLATION

ABC Type 6 kg with indicating gauge

Fire Buckets of 9 lit. water capacity filled with sand with stand at D.G. & Transformer Yard .

Laxmi Civil Engineering Services Pvt. Ltd.