Construction of OPD Room, Vocational Training Center, Canteen, Open Air Theater, Hardcore cell at Vadodara Central Jail Vadodara Dist Vadodara (Including Electrification) [2nd Attempt]

No. InFigure In Words Rs.

1 Demolition including stacking of serviceable materilas and disposal of 5.00 Cum. 1073.56 Rs. One Thousand

unserviceable materials with all lead and lift. (i) R.C.C. work Seventy Three &

Paise Fifty Six Only

2 Excavation for foundation in Loose and Soft soil upto 1.5 m. depth including sorting 800.00 Cum. 118.82 Rs. One Hundred

out and stacking of useful materials and disposing of the excavated stuff upto any Eighteen & Paise

Lead and Lift. Eighty Two Only

3 Excavation for foundation in Dence or hard soil from upto 1.5 mt depth including 535.00 Cum. 151.89 Rs. One Hundred

sorting out and stacking of useful materials and disposing of the excavated stuff Fifty One & Paise

upto any Lead and Lift. Eighty Nine Only

4 Excavation for foundation in Dense or hard soil from 1.5 mt.to 3.0 mt. depth 385.00 Cum. 164.79 Rs. One Hundred

including sorting out and stacking of useful materials and disposing of the Sixty Four & Paise

excavated stuff upto any Lead and Lift. Seventy Nine Only

5 Excavation for foundation in Dense or Hard from up to 3.00 mt to 5.0 mt depth 18.00 Cum. 178.59 Rs. One Hundred

including sorting out and stacking of useful materials and disposing of the Seventy Eight &

excavated stuff upto any lead & Lift Paise Fifty Nine

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

6 Providing & Laying Cement Concrete 1:3:6 ( 1 Cement : 3 Coarse Sand : 6hand 114.00 Cum 3050.40 Rs. Three

broken stone aggregate of 40mm Nominal Size) & curing Complete excluding cost Thousand Fifty &

of formwork in Foundation & Plinth. Paise Forty Only

7 Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand 264.00 Cum. 2720.01 Rs. Two Thousand

broken stone aggregates 40 mm nominal size) and curing complete excluding the Seven Hundred

cost of formwork of Plywood only with fair finish & Proping must be of steel only Twenty & Paise

so as to give fair finish in (A) Foundation and Plinth . One Only

8 Providing & laying Controlled CEMENT CONCRETE M-250 and curing complete 274.00 Cum. 4571.96 Rs. Four Thousand

including cost of formwork with sheathing steel sheets so as to give a fair finish but Five Hundred

excluding the cost of reinforcement in column FOOTING base of columns and Mass Seventy One &

concrete. Rate are also inclusive of providing and mixing Plasticiser of approved Paise Ninety Six

make in proportion as per mix design Only

9 Providing & laying Controlled CEMENT CONCRETE M-250 and curing complete 82.00 Cum. 8788.27 Rs. Eight Thousand

including cost of formworkof Plywood only with fair finish & Proping must be of Seven Hundred

steel only so as to give fair finish but excluding the cost of reinforcement in Eighty Eight &

COLUMN upto PLINTH for any cross sectional area of column. Rate are also Paise Twenty

inclusive of providing and mixing Plasticiser of approved make in proportion as per Seven Only

mix design

10 Providing and laying Controlled cement concrete M-250 and finishing smooth with 198.00 Cum. 7129.20 Rs. Seven

curing etc.. complete including the cost of formworkof Plywood only with fair finish Thousand One

& Proping must be of steel only so as to give fair finish but exculding the cost of Hundred Twenty

reinforcement for PLINTH BEAMS of any cross sectional area of beam. Rate are Nine & Paise

also inclusive of providing and mixing Plasticiser of approved make in proportion . Twenty Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

11 Filling available excavated earth (excluding rock) in trenches. plinth, sides 1711.00 Cum. 132.33 Rs. One Hundred

of foundations etc. in layers not exceeding 20 cm. in depth consolidating each Thirty Two & Paise

disposited layer by ramming and watering. Thirty Three Only

thickness including watering, ramming and consolidating etc. complete. Ninety Three &

Paise Thirty Six

13 Providing and filling brick bats in sock well as per drawing and specification.etc 6.00 Cum. 497.80 Rs. Four Hundred

complete Ninety Seven &

Paise Eighty Only

14 Applying general insecticide Pest Control Treatment to floors, cupboards etc 1232.00 Sqm 51.34 Rs. Fifty One &

including labour materials etc. complete. Using midacloprid 30.5 SCas Per IS 6313 Paise Thirty Four

part -II( (0.075% concentration by mass) is recommended 10.5ml chemical diluted Only

with 5 liters of water application 0.5 litre chemical /Sqm of surface is recommended

as per I.S.

15 FILLING in plinth with SAND under floors including watering, raming 149.00 Cum. 467.02 Rs. Four Hundred

consolidating and dressing etc. complete. Sixty Seven & Paise

16 Providing and laying cement concrete 1:5:10 (1- Cement : 5- coarse sand : 10- hand 96.00 Cum. 2554.82 Rs. Two Thousand

broken stone aggregates 40 mm nominal size) and curing complete excluding the Five Hundred Fifty

cost of formwork of Plywood only with fair finish & Proping must be of steel only Four & Paise

so as to give fair finish in (A) Foundation and Plinth . Eighty Two Only

17 Provinding and Laying controlled cement concrete M-150 including the cost of 7.00 Cum. 3948.78 Rs. Three

formwork of Plywood only with fair finish & Proping must be of steel only so as to Thousand Nine

give fair finish but excluding the cost of reinforcement for R.C.C.Grade Slab. Rate Hundred Forty

are also inclusive of providing and mixing Plasticiser of approved make in Eight & Paise

proportion as per mix design . Seventy Eight Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

18 Provinding and laying Controlled cement concrete M-200 and finishing smooth with 140.00 Cum. 3967.60 Rs. Three

curing etc. complete excluding the cost form work and reinforcement for RCC work Thousand Nine

in FOUNDATION & PLINTH for any cross sectional area of column. Providing and Hundred Sixty

Mixing Plasticiser in cement concrete as per mix design Seven & Paise Sixty

19 Provinding and laying Controlled cement concrete M-250 and finishing smooth with 38.00 Cum. 5983.60 Rs. Five Thousand

curing etc. complete including the cost form workof Plywood only with fair finish & Nine Hundred

Proping must be of steel only so as to give fair finish but excluding the cost of Eighty Three &

reinforcement for RCC work in COPING for any cross sectional area of column. Paise Sixty Only

Rate are also inclusive of providing and mixing Plasticiser of approved make in

proportion as per mix design

20 Providing and laying controlled cement concrete M-250 and finishing smooth with 117.00 Cum. 10607.10 Rs. Ten Thousand

curing etc. complete Including the cost of form workof Plywood only with fair finish Six Hundred Seven

& Proping must be of steel only so as to give fair finish but excluding the cost of & Paise Ten Only

reinforcement for R.C.C. work in COLUMNS for any cross sectional area at

GROUND FLOOR. Rate are also inclusive of providing and mixing Plasticiser of

approved make in proportion as per mix design .

21 Providing and laying controlled cement concrete M-250 and finishing smooth with 26.00 Cum. 10646.65 Rs. Ten Thousand

curing etc. complete Including the cost of form workof Plywood only with fair finish Six Hundred Forty

& Proping must be of steel only so as to give fair finish but excluding the cost of Six & Paise Sixty

reinforcement for R.C.C. work in COLUMNS for any cross sectional area at FIRST Five Only

FLOOR. Rate are also inclusive of providing and mixing Plasticiser of approved

make in proportion as per mix design .

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

22 Providing and laying controlled cement concrete M-250 and finishing smooth with 7.00 Cum. 10686.20 Rs. Ten Thousand

curing etc. complete Including the cost of form workof Plywood only with fair finish Six Hundred

& Proping must be of steel only so as to give fair finish but excluding the cost of Eighty Six & Paise

reinforcement for R.C.C. work in COLUMNS for any cross sectional area at Twenty Only

SECOND FLOOR. Rate are also inclusive of providing and mixing Plasticiser of

approved make in proportion as per mix design .

23 Provinding and Laying Cement concrete 1:3:6 including the cost of formworkof 2.00 Cum. 7584.49 Rs. Seven

Plywood only with fair finish & Proping must be of steel only so as to give fair Thousand Five

finish but excluding cost of the reinforcement for RCC Work etc complete For Hundred Eighty

Column at any Floor for any cross sectional area. Four & Paise Forty

24 Providing and laying Controlled cement concrete M-250 and finishing smooth with 150.00 Cum. 8897.46 Rs. Eight Thousand

curing etc.. complete including the cost of formworkof Plywood only with fair finish Eight Hundred

& Proping must be of steel only so as to give fair finish but exculding the cost of Ninety Seven &

reinforcement for BEAMS having any cross sectional area for GROUND FLOOR. Paise Forty Six

Rate are also inclusive of providing and mixing Plasticiser of approved make in Only

proportion as per mix design .

25 Providing and laying Controlled cement concrete M-250 and finishing smooth with 37.00 Cum. 8937.01 Rs. Eight Thousand

curing etc.. complete including the cost of formworkof Plywood only with fair finish Nine Hundred

& Proping must be of steel only so as to give fair finish but exculding the cost of Thirty Seven &

reinforcement for BEAMS having any cross sectional area for FIRST FLOOR. Rate Paise One Only

are also inclusive of providing and mixing Plasticiser of approved make in

proportion as per mix design .

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

26 Providing and laying Controlled cement concrete M-250 and finishing smooth with 7.00 Cum. 8976.56 Rs. Eight Thousand

curing etc.. complete including the cost of formworkof Plywood only with fair finish Nine Hundred

& Proping must be of steel only so as to give fair finish but exculding the cost of Seventy Six & Paise

reinforcement for BEAMS having any cross sectional area for SECOND FLOOR. Fifty Six Only

Rate are also inclusive of providing and mixing Plasticiser of approved make in

proportion as per mix design .

27 Providing and laying Controlled cement concrete M-250 finishing smooth with 45.00 Cum. 8148.57 Rs. Eight Thousand

curing etc.complete including the cost of formwork of Plywood only with fair finish One Hundred

& Proping must be of steel only so as to give fair finish but excluding the cost of Forty Eight & Paise

reinforcement for R.C.C. work in SLAB having thickness of 10cm. and up to 13 cms Fifty Seven Only

for GROUND FLOOR Rate are also inclusive of providing and mixing Plasticiser of

approved make in proportion as per mix design

28 Provinding and Laying controlled cement concrete M-250 finishing smooth with 131.00 Cum. 7722.96 Rs. Seven

curing etc. completeincluding the cost of formworkof Plywood only with fair finish Thousand Seven

& Proping must be of steel only so as to give fair finish but exculding the cost of Hundred Twenty

reinforcement for R.C.C. work in SLAB having thickness of 13 cm and upto 15cm Two & Paise

for GROUND FLOOR. Rate are also inclusive of providing and mixing Plasticiser of Ninety Six Only

approved make in proportion as per mix design .

29 Providing and laying Controlled cement concrete M-200 finishing smooth with 2.00 Cum. 7614.70 Rs. Seven

curing etc.complete including the the cost of formwork of Plywood only with fair Thousand Six

finish & Proping must be of steel only so as to give fair finish but excluding the cost Hundred Fourteen

of reinforcement for R.C.C. work in SLAB having thickness of 13cm. and up to 15 & Paise Seventy

cms for GROUND FLOOR Rate are also inclusive of providing and mixing Only

Plasticiser of approved make in proportion as per mix design etc.as per direction of

Engineer in charge.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

30 Providing and laying Controlled cement concrete M-250 finishing smooth with 4.00 Cum. 7130.66 Rs. Seven

curing etc.complete including the cost of formwork of Plywood only with fair finish Thousand One

& Proping must be of steel only so as to give fair finish but excluding the cost of Hundred Thirty &

reinforcement for R.C.C. work in SLAB having thickness of 15cm. and up to 20 cms Paise Sixty Six

for GROUND FLOOR Rate are also inclusive of providing and mixing Plasticiser of Only

approved make in proportion as per mix design

31 Providing and laying Controlled cement concrete M-250 finishing smooth with 29.00 Cum. 8188.12 Rs. Eight Thousand

curing etc.complete including the cost of formwork of Plywood only with fair finish One Hundred

& Proping must be of steel only so as to give fair finish but excluding the cost of Eighty Eight &

reinforcement for R.C.C. work in SLAB having thickness of 10cm. and up to 13 cms Paise Twelve Only

for FIRST FLOOR Rate are also inclusive of providing and mixing Plasticiser of

approved make in proportion as per mix design

32 Provinding and Laying controlled cement concrete M-250 finishing smooth with 27.00 Cum. 7762.51 Rs. Seven

curing etc. completeincluding the cost of formworkof Plywood only with fair finish Thousand Seven

& Proping must be of steel only so as to give fair finish but exculding the cost of Hundred Sixty

reinforcement for R.C.C. work in SLAB having thickness of 13 cm and upto 15cm Two & Paise Fifty

for FIRST FLOOR. Rate are also inclusive of providing and mixing Plasticiser of One Only

approved make in proportion as per mix design .

33 Providing and laying Controlled cement concrete M-250 finishing smooth with 1.00 Cum. 7170.21 Rs. Seven

curing etc.complete including the cost of formwork of Plywood only with fair finish Thousand One

& Proping must be of steel only so as to give fair finish but excluding the cost of Hundred Seventy

reinforcement for R.C.C. work in SLAB having thickness of 15cm. and up to 20 cms & Paise Twenty

for FIRST FLOOR Rate are also inclusive of providing and mixing Plasticiser of One Only

approved make in proportion as per mix design

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

34 Providing and laying Controlled cement concrete M-250 finishing smooth with 6.00 Cum. 8227.67 Rs. Eight Thousand

curing etc.complete including the cost of formwork of Plywood only with fair finish Two Hundred

& Proping must be of steel only so as to give fair finish but excluding the cost of Twenty Seven &

reinforcement for R.C.C. work in SLAB having thickness of 10cm. and up to 13 cms Paise Sixty Seven

for SECOND FLOOR Rate are also inclusive of providing and mixing Plasticiser of Only

approved make in proportion as per mix design

35 Provinding and Laying controlled cement concrete M-250 finishing smooth with 3.00 Cum. 7802.06 Rs. Seven

curing etc. completeincluding the cost of formworkof Plywood only with fair finish Thousand Eight

& Proping must be of steel only so as to give fair finish but exculding the cost of Hundred Two &

reinforcement for R.C.C. work in SLAB having thickness of 13 cm and upto 15cm Paise Six Only

for SECOND FLOOR. Rate are also inclusive of providing and mixing Plasticiser of

approved make in proportion as per mix design .

36 Providing and laying Controlled cement concrete M-250 for R.C.C. LINTEL 20.00 Cum. 8612.77 Rs. Eight Thousand

including finishing smooth with curing etc. Complete including the cost of Six Hundred

formwork of Plywood only with fair finish & Proping must be of steel only so as to Twelve & Paise

give fair finish but excluding the cost of reinforcement for GROUND FLOOR Rate Seventy Seven

are also inclusive of providing and mixing Plasticiser of approved make in Only

proportion as per mix design .

37 Providing and laying Controlled cement concrete M-250 for R.C.C. LINTEL 7.00 Cum. 8652.32 Rs. Eight Thousand

including finishing smooth with curing etc. Complete including the cost of Six Hundred Fifty

formwork of Plywood only with fair finish & Proping must be of steel only so as to Two & Paise Thirty

give fair finish but excluding the cost of reinforcement for FIRST FLOOR Rate are Two Only

also inclusive of providing and mixing Plasticiser of approved make in proportion

as per mix design .

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

38 Providing and laying Controlled cement concrete M-250 for R.C.C. LINTEL 2.00 Cum. 8691.87 Rs. Eight Thousand

including finishing smooth with curing etc. Complete including the cost of Six Hundred

formwork of Plywood only with fair finish & Proping must be of steel only so as to Ninety One & Paise

give fair finish but excluding the cost of reinforcement for SECOND FLOOR Rate Eighty Seven Only

are also inclusive of providing and mixing Plasticiser of approved make in

proportion as per mix design .

39 Providing and laying Controlled cement concrete M-250 for R.C.C. LINTELBEND 5.00 Cum. 5983.60 Rs. Five Thousand

including finishing smooth with curing etc. Complete including the cost of Nine Hundred

formworkof Plywood only with fair finish & Proping must be of steel only so as to Eighty Three &

give fair finish but excluding the cost of reinforcement for Ground FLOOR Rate are Paise Sixty Only

also inclusive of providing and mixing Plasticiser of approved make in proportion

as per mix design

40 Providing and laying Controlled cement concrete M-250 for R.C.C. LINTELBEND 2.00 Cum. 6023.15 Rs. Six Thousand

including finishing smooth with curing etc. Complete including the cost of Twenty Three &

formworkof Plywood only with fair finish & Proping must be of steel only so as to Paise Fifteen Only

give fair finish but excluding the cost of reinforcement for First FLOOR Rate are also

inclusive of providing and mixing Plasticiser of approved make in proportion as per

mix design

41 Providing and laying Controlled cement concrete M-250 for R.C.C. Staircase upto 4.00 Cum. 8251.26 Rs. Eight Thousand

floor level for all Floor including finishing smooth with curing etc. Complete Two Hundred

including the cost of formwork of Plywood only with fair finish & Proping must be Thirty One & Paise

of steel only so as to give fair finish but excluding the cost of reinforcement. Rate are Forty Eight Only

also inclusive of providing and mixing Plasticiser of approved make in proportion

as per mix design

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

42 Provinding and Laying controlled cement concrete M-250 for reinforced conerete 20.00 Cum. 9707.63 Rs. Nine Thousand

CHHAJJAS for any thickness including finishing the exposed surface with cement Seven Hundred

mortar 1:3 ( 1 cement : 3 fine sand) to give a smooth surface ,centering and Seven & Paise Sixty

formwork of Plywood only with fair finish & Proping must be of steel only so as to Three Only

give fair finish and curing complete. excluding cost of reinforcement for ALL

FLOOR. Rate are also inclusive of providing and mixing Plasticiser of approved

make in proportion as per mix design

43 Providing and laying Controlled cement concrete M-250 including finishing smooth 13.00 Cum. 8251.26 Rs. Eight Thousand

for R.C.C. STAIR CASE including the cost of formworkof Plywood only with fair Two Hundred Fifty

finish & Proping must be of steel only so as to give fair finish and curing etc. One & Paise

Complete excluding cost of reinforcement for ALL FLOORS. Rate are inclusive of Twenty Six Only

Providing and Mixing Plasticiser in cement concrete as per mix design including

rate of labour,material etc.as per direction of Engineer in charge.

44 Providing TMT Bars Fe -500 D reinforcement for RCC work including cutting, 109234.00 Kg 76.67 Rs. Seventy Six &

bending, binding and placing in position etc.complete for all floors.Steel must be Paise Sixty Seven

used Approved Material list of GSPHCL. Only

45 BRICK WORK using common burnt clay building bricks having crushing strength 400.00 Cum. 4080.74 Rs. Four Thousand

not less than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 Eighty & Paise

cement : 6 coarse sand ( Conventional Bricks) for Foundation & Plinth. Seventy Four Only

46 BRICK WORK using common burnt clay building bricks having crushing strength 822.00 Cum. 4359.80 Rs. Four Thousand

not less than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 Three Hundred

cement : 6 coarse sand ( Conventional Bricks) for GROUND FLOOR. Fifty Nine & Paise

Eighty Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

47 BRICK WORK using common burnt clay building bricks having crushing strength 178.00 Cum. 4400.58 Rs. Four Thousand

not less than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 Four Hundred &

cement : 6 coarse sand ( Conventional Bricks) for FIRST FLOOR. Paise Fifty Eight

48 BRICK WORK using common burnt clay building bricks having crushing strength 56.00 Cum. 4441.36 Rs. Four Thousand

not less than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 Four Hundred

cement : 6 coarse sand ( Conventional Bricks) for SECOND FLOOR. Forty One & Paise

Thirty Six Only

49 HALF BRICK masonary in common brunt clay building bricks having crusing 10.00 Sqm 608.75 Rs. Six Hundred

strength not less than 35 kg./sq.cm.in cement mortar 1:4 (1 cement : 4 coarse sand ) Eight & Paise

conventional bricks for Foundation Seventy Five Only

50 Half Brick masonary in common burnt clay building bricks having crushing 296.00 Sqm 662.87 Rs. Six Hundred

strength not less than 35 kg./sq.cm. in cement mortar 1:4 (1 cement: 4 coarse sand) Sixty Two & Paise

conventional bricks for Ground Floor Eighty Seven Only

51 Half Brick masonary in common burnt clay building bricks having crushing 14.00 Sqm 668.96 Rs. Six Hundred

strength not less than 35 kg./sq.cm. in cement mortar 1:4 (1 cement: 4 coarse sand) Sixty Eight & Paise

conventional bricks for First Floor Ninety Six Only

52 Provinding and fixing chicken wire mesh Jali 0.18 mm and 0.18mt wide with 590.00 Sqm 64.06 Rs. Sixty Four &

necessary screws and nails to joint between R.C.C. column and brick work etc. Paise Six Only

complete as per Engineer-in-charge.

53 Providing 10 mm thick cement PLASTER in single coat on ceilings for interior 992.00 Sqm 217.78 Rs. Two Hundred

plastering and finished even & smooth in C.M. 1:3 ( 1 cement : 3 sand )including Seventeen & Paise

finishing with a floating coat of neat cement slurry at GROUND FLOOR. Seventy Eight Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

54 Providing 10 mm thick cement PLASTER in single coat on ceilings for interior 388.50 Sqm 244.24 Rs. Two Hundred

plastering and finished even & smooth in C.M. 1:3 ( 1 cement : 3 sand )including Forty Four & Paise

finishing with a floating coat of neat cement slurry at FIRST FLOOR. Twenty Four Only

55 Providing 10 mm thick cement PLASTER in single coat on ceilings for interior 67.00 Sqm 270.70 Rs. Two Hundred

plastering and finished even & smooth in C.M. 1:3 ( 1 cement : 3 sand )including Seventy & Paise

finishing with a floating coat of neat cement slurry at SECOND FLOOR. Seventy Only

56 Provinding 15 mm thick cement PLASTER in single coat on brick or concrete wall 3240.00 Sqm 218.43 Rs. Two Hundred

for interior plastering and finished even and smooth in C.M. 1:4 ( 1 cement : 4 sand Eighteen & Paise

) including finishing with floating coat of neat cement slurry at GROUND FLOOR. Forty Three Only

57 Provinding 15 mm thick cement PLASTER in single coat on brick or concrete wall 1017.00 Sqm 246.99 Rs. Two Hundred

for interior plastering and finished even and smooth in C.M. 1:4 ( 1 cement : 4 sand Forty Six & Paise

) including finishing with floating coat of neat cement slurry at FIRST FLOOR. Ninety Nine Only

58 Provinding 15 mm thick cement PLASTER in single coat on brick or concrete wall 218.00 Sqm 275.55 Rs. Two Hundred

for interior plastering and finished even and smooth in C.M. 1:4 ( 1 cement : 4 sand Seventy Five &

) including finishing with floating coat of neat cement slurry at SECOND FLOOR. Paise Fifty Five

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

59 Synthetic Texture Plaster with Double Coat Smooth plaster : Providing 20mm thick 3069.00 Sqm 491.26 Rs. Four Hundred

cement plaster in single coat plastering upto floor two level Outside and finished Ninety One & Paise

even and smooth in (i) Cement mortar 1:3 (1-cement : 3-sand) as Base Coat and Twenty Six Only

providing 2-3 mm thick synthetic texture plaster of approved texture (Material

Shall be Used as Approved By GSPHCL Only ) including cost of all materials,

labour, conveyance, loading and unloading, taxes, royalties, scaffolding, watering

etc.complete for any Height as per Drawing and instructions of Engineer -in -

60 Providing 20 mm thick SAND FACED cement Plaster on walls above ground level 5.00 Sqm 334.18 Rs. Three Hundred

consisting 12 mm thick backing coat of C.M. 1: 3 ( 1 cement : 3 sand ) and 8mm thick Thirty Four & Paise

finishing coat of C.M. 1:1 ( 1 cement : 1 sand ) etc. Complete for any height. Eighteen Only

61 Provinding 10 mm thick cement PLASTER in single coat of interior plastering and 127.00 Sqm 228.98 Rs. Two Hundred

finished even and smooth in cement mortar 1:3 ( 1 cement : 3 sand ) and finishing Twenty Eight &

with floating coat of neat cement slurry including providing and mixing with Paise Ninety Eight

WATER PROOFING material For ALL FLOORS. Only

62 Providing and laying acrylic base (Zycosil) equvivalant water proofing paint in two 26.00 Sqm 110.70 Rs. One Hundred

coats to vertical and horizontal surface of depressed portion of bath and W.C. as Ten & Paise

directed by engineer -in- charge. This treatement shall be carried out over and Seventy Only

above water proofing cement plaster.

63 Provinding CEMENT VATA (10cm x 10cm) size quarter round in cement mortar (1 : 347.00 Rmt 24.04 Rs. Twenty Four &

1) including neat cement finishing, watering etc. Complete. Paise Four Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

64 Providing and filling Cinder including watering, consolidation etc.complete. 1.00 Cum 791.68 Rs. Seven Hundred

Ninety One & Paise

Sixty Eight Only

65 Providing and laying cement concrete 1:2:4 (1-cement:2-coarse sand:4-stone 32.00 Cum 3619.93 Rs. Three

aggregates 20mmof nominal size) and curing etc.complete including cost of Thousand Six

formwork in foundation and plinth. Hundred Ninteen

& Paise Ninety

Three Only

66 Providing and laying cement concrete flooring 1:2:4 (1 cement : 2-coarse sand : 4- 222.00 Sqm 337.41 Rs. Three Hundred

graded stone aggregate 20mm nominal size) laid in one layer and finished with a Thirty Seven &

floating coat of neat cement. (B) 50mm thick. Paise Forty One

67 Providing & Laying 24" x 24" Double Charge vitrified 8 to 10 mm thick tile flooring 1254.00 Sqm 1700.50 Rs. One Thousand

over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new Seven Hundred &

surface orfixing on existing flooring by adhesive including dismentaling of existing Paise Fifty Only

flooring and material jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete size and shade of tiles shall be as per

approved architecture drawing and as per direction of engineer-in-charge for all

68 Providing & Laying 24" x 24" Double Charge vitrified 8 to 10 mm thick tile for 88.00 Sqm 1420.50 Rs. One Thousand

skirting,risers of steps and dedo over 20 mm (average) base of cement mortar 1:6 ( 1 Four Hundred

cement: 6 coarse sand) on new surface orfixing on existing flooring by adhesive Twenty & Paise

including dismentaling of existing flooring and material jointed with color cement Fifty Only

slurry including finised with flush pointing & cleaning the surface etc. complete size

and shade of tiles shall be as per approved architecture drawing and as per

direction of engineer-in-charge for all floors .

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

69 Provinding & laying 24" x 24" vitrified 8mm thick tile flooring over 20 mm (average) 101.00 Sqm 1418.59 Rs. One Thousand

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on Four Hundred

existing flooring by adhesive material including dismentaling of existing flooring Eighteen & Paise

and material jointed with color cement slurry including finised with flush pointing Fifty Nine Only

& cleaning the surface etc. complete for antiskid. size and shade of tiles shall be as

per approved architecture drawing and as per direction of engineer-in-charge for all

70 Constructing of cooking platform ( sandwich type ) 68cm width and 84 cm high 4.00 Rmt 3758.21 Rs. Three

resting on thick sandwiched polish Granite Slab in C.M 1:3 with providing and Thousand Seven

fixing 25 mm thick rough kota stone at bottom and 20 to 25 mm thick Polish Granite Hundred Fifty

stone ( single piece/ telephonic Black ) top & Vertical and polished granite stone Eight & Paise

(single piece/ telephonic Black ) 20 to 25mm thick on top & polished granite round Twenty One Only

moulded Top facia patty including polishing etc . complete as per drawing and

specification without stainless steel sink including necessary cutting for sink &

making hole for gas pipe and fixing P.V.C bend of 25mm dia.

71 Provinding & laying Printed / Coloured GLAZED TILES 8 mm thick in skirting, 583.00 Sqm 1462.62 Rs. One Thousand

risers of steps and DADO on 10mm thick cement plaster 1: 3 ( 1 cement : 3 coarse Four Hundred

sand ) & jointed with white cement slurry.Size ot tiles shall be 600mm x300mm. size Sixty Two & Paise

and shade of tiles shall be as per approved architecture drawing and as per Sixty Two Only

direction of engineer-in-charge for all floors .

72 Providing and laying Granite Slab (18 mm thick) of approved colour & quality & 121.00 Sqm. 2140.38 Rs. Two Thousand

brand, one side polished flooring over 20 mm (average) base of cement mortar 1:6 (1 One Hundred

cement : 6 coarse sand) laid and jointed with grey cement slurry including rubbing, Forty & Paise

curing including grooving, moulding, nosing of corners and mirror polishing Thirty Eight Only

complete.For flooring of steps, stairs with treads & risers etc.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

73 Providing and laying Granite Slab (18 mm thick) of approved colour & quality & 43.00 Sqm. 2287.29 Rs. Two Thousand

brand, one side polished flooring over 20 mm (average) base of cement mortar 1:6 (1 Two Hundred

cement : 6 coarse sand) laid and jointed with grey cement slurry including rubbing, Eighty Seven &

curing including nosing of corners and mirror polishing complete.For Skirting. Paise Twenty Nine

74 Providing and fixing both side polished machine cut KOTA STONE shelve/ 306.00 Sqm. 589.50 Rs. Five Hundred

partition 20mm to 25mm thick embaded in to wall at support including racking and Eighty Nine &

finishing smooth the surface including cutting the stone as and where required etc. Paise Fifty Only

complete including rounding of exposed edges etc. complete.

75 Providing and fixing both side polished machine cut Telephone Black Granite 16.00 Sqm 3322.80 Rs. Three

Shelves / Partitions 18mm thick embaded in to wall at support including racking Thousand Three

and finishing smooth the surface including cutting the stone as and where required Hundred Twenty

etc. complete including rounding of exposed edges etc. complete. Two & Paise Eighty

76 Providing and Fixing Granite Telephonic Black Colour 15 to 18 mm thick for jambs 347.00 Sqm 2428.00 Rs. Two Thousand

and sills of doors & windows using neat cement slurry laid over 20 mm average Four Hundred

base of cement mortar 1:1(1 cement:1 Coarse Sand) and jointed with grey cement Twenty Eight Only

slurry including racking(Tancha Work) rubbing and polishing,scaffoldings,tools

and tackles,scaffolding etc. complete(with base of neat cement) as per direction of

Engineer in charge including full rounding the exposed edges as directed.

77 Providing and Laying 25mm thick Mirror Polished (Dimond Cut) Kota Stone 46.00 Sqm 1090.30 Rs. One Thousand

Flooring over 20mm thick base of cement mortar 1 : 6 (1-Cement : 6-Coarse Sand) Ninety & Paise

laid over and jointed with grey cement slurry including Rubbing and Polishing etc. Thirty Only

Complete as Directed By Engineer In Charge for all Floors.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

78 Providing and Laying 25mm thick Mirror Polished (Dimond Cut) Kota Stone in 5.00 Sqm 1237.20 Rs. One Thousand

risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1- Two Hundred

Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to Thirty Seven &

match the shade of slab including rubbing and polishing etc. complete as Directed Paise Twenty Only

By Engineer In Charge for all Floors.

79 Providing and laying 25mm thick one edge machine cut rough kota stone flooring 8.00 Sqm 718.99 Rs. Seven Hundred

(other edge chisel dressed) over 20mm thick base of cement mortar 1:5 including Eighteen & Paise

pointing with 1:2 etc complete (25mm thick) Ninety Nine Only

80 Providing and fixing window having extruded aluminum Colour anodized section 79.00 Sqm 1568.27 Rs. One Thousand

frame main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal Five Hundred Sixty

Three track member size 92mm x 31.75mm x 1.30mm,@ Wt.1.07 Kg/mt , vertical Eight & Paise

member of size 92mm x 31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with sliding shutters Twenty Seven Only

of horizontal member member of size 40mm x 18mm x 1.29 mm @ wt.of

0.456Kg/mt/ with 5 mm thick transparent bronze colour size 40 mmx18mm

x1.29mm @ wt.of 0.456 Kg/mt, vertical tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame

as per details etc

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

81 Providing and fixing Alluminium section window having extruded Aluminum 28.00 Sqm 1807.10 Rs. One Thousand

Colour anodized section frame main outer size 95mm x 24mm x 1.17mm (of Jindal Eight Hundred

Section no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track member size 92mm x Seven & Paise Ten

31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07 Kg/mt), vertical member of Only

size 92mm x 31.75mm x 1.50mm (of Jindal Section no:8933,@ Wt. 1.06 Kg/mt) with

sliding shutters of horizontal member size 40mm x 18mm x 1.29mm (of Jindal

Section no:8947@ wt.of 0.456 Kg/mt), vertical member of size 40mm x 18mm x

mm (of Jindal Section no:8949 @ wt.of 0.456Kg/mt) with 5 mm thick transparent

bronze colour tinted float glass with powder coated aluminum fittings and fixtures

and transparent silicon sealant glass fixing to frame as per details including one

mosquitoe jali shutter With Both Side Locking Arrangment for ALL FLOORS.

82 Providing and fixing standard extruded of ALLUMINIUM SECTION of size 63mm 9.00 Sqm 1163.92 Rs. One Thousand

x 38.10mm x 1.2mm (Jindal Section :2434,@Wt.0.643 kg per mt) with colour One Hundred Sixty

anodized alluminium frame for ventilation with 5mm thick frosted glass as details Three & Paise

etc complete for VENTILATION. Ninety Two Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

83 Providing, Supplying and Fixing of 32mm (Total) Thick Double Flush Door Shutter 5.00 Sqm 11086.11 Rs. Eleven

with 1mm Thick Laminates on Both Side of Shutter. Making / Construction of Flush Thousand Eighty

Door is with Pine or southern Yellow Pine Filler and 2.5mm core veneer Both Side Six & Paise Eleven

and 0.4mm Face Veneer on Both Side with Lock rail on Center. Flush Door Provide Only

with Teak wood beading patti (32mm X 12mm) on Peripheries of Flush Door with

Door Frame of Non Teak Solid Wood of size 150mm x 70mm with Chemically

Treated and Seasoned Including Paint Matching with Laminates. Frame & Flush

door shutter having 5 year warranty against attack of biological agent like termite,

borers, decay, fungi and harmful insects also warranty against seasoning related

issues like crack, bending, twisting, warping. Laminates on shutter shall be press by

cold press method. Shutter shall be brought to site in packed PVC bags & pvc

coating shall be removed on completion of work in such a way that shutter & Frame

is free from nail mark & any damages etc. Rates are also Inclusive of all Labors &

Proviging 15cm. Long 8 No of Hold Fast (25mm X 5mm) & 8 No of 6 Inch S.S. but

Hinges, 100mm x 75 mm x 3mm thick, required Screw & Nails per Frame and Fixing

following S.S. Fixtures And Fastening.

(1) Aldrops 2 No, 250mm x 16mm, (2) Door Stopper 2 No, 100mm Long, (3) Double

Leg Heavy Push Door Stopper 2 No & (4) Handle 4 No, 150mm Long X 10mm thick.

Door are Fixing as per Details Drawing & Instruction of Engineer in charge. All

Materials Used Shall be as Per approved Material Make List of G.S.P.H.C. The

Required Frame is to be Obtained from Vanil Udhyog Maked Only.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

84 Providing, Supplying and Fixing of 32mm (Total) Thick Single Flush Door Shutter 60.00 Sqm 8404.29 Rs. Eight Thousand

with 1mm Thick Laminates on Both Side of Shutter. Making / Construction of Flush Four Hundred

Door is with Pine or southern Yellow Pine Filler and 2.5mm core veneer Both Side Four & Paise

and 0.4mm Face Veneer on Both Side with Lock rail on Center. Flush Door Provide Twenty Nine Only

with Teak wood beading patti (32mm X 12mm) on Peripheries of Flush Door with

Door Frame of Non Teak Solid Wood of size 100mm x 60mm with Chemically

Treated and Seasoned Including Paint Matching with Laminates. Frame & Flush

door shutter having 5 year warranty against attack of biological agent like termite,

borers, decay, fungi and harmful insects also warranty against seasoning related

issues like crack, bending, twisting, warping. Laminates on shutter shall be press by

cold press method. Shutter shall be brought to site in packed PVC bags & pvc

coating shall be removed on completion of work in such a way that shutter & Frame

is free from nail mark & any damages etc. Rates are also Inclusive of all Labors &

Proviging 15cm. Long 8 No of Hold Fast (25mm X 5mm) & 4 No of 6 Inch S.S. but

Hinges, 100mm x 75 mm x 3mm thick, required Screw & Nails per Frame and Fixing

6mm thick Glass on Top of Door Frame with Battens Patti, following S.S. Fixtures

And Fastening.

(1) Aldrops 1 No, 250mm x 16mm & Tadi 1 No, (2) Door Stopper 1 No, 100mm 0.00

Long, (3) Double Leg Heavy Push Door Stopper 1 No & (4) Handle 2 No, 150mm

Long X 10mm thick. Door with Glass are Fixing as per Details Drawing &

Instruction of Engineer in charge. All Materials Used Shall be as Per approved

Material Make List of G.S.P.H.C. The Required Frame is to be Obtained from Vanil

Udhyog Maked Only.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

85 Providing and fixing Solid PVC Flush Door Shutters 24mm thick made fro Co- 73.00 Sqm 4475.57 Rs. Four Thousand

Extruded THREE LAYER RIGID PVC Foam Sheet (Single extruded) with density Four Hundred

not less than 600 Kg / cbm. Outer Layer (0.8-1mm) thick should be of Rigid PVC Seventy Five &

with Density not less than 1400 kg/cbm including Providing & Fixing WPC Door Paise Fifty Seven

Frame Uperline Patti of 24mm x 6mm Size. Door should be Water proof, Termite Only

proof, Fire Retardant & having good screw holding capacity. Providing & Fixing

100% Solid Wood Plastic Composit (WPC) Door Frame 90mm x 45mm made from

Wood Plastic Composite (Single extruded Process) material with dencity 780kg /

cbm All as per specifications & drawings etc. complete as per direction of Engineer-

in-charge.

86 Providing and fixing to wall, ceiling and floor U.PVC SWR Soil Waste Pipe with 340.00 Rmt. 471.36 Rs. Four Hundred

'O' Ring 110 mm dia. of ISI 13592/92. Rate inclusive of All fittings like single or Seventy One &

double 'Y' with door, reducer, coupler single 'T' with door bend,including All Paise Thirty Six

Labour Charges etc. complete and making good the Wall, Ceiling and Floor, ISI Only

make only. Joints shall be sealed by pipe sealant.

87 Providing and fixing to wall, ceiling and floor U.PVC SWR Soil Waste Pipe with 187.00 Rmt. 245.74 Rs. Two Hundred

'O' Ring 75 mm dia. of ISI 13592/92. Rate inclusive of All fittings like single or Forty Five & Paise

double 'Y' with door, reducer, coupler single 'T' with door bend,including All Seventy Four Only

Labour Charges etc. complete and making good the Wall, Ceiling and Floor, ISI

make only. Joints shall be sealed by pipe sealant.

88 P & F to Wall Ceilling and Floor SWR Rain Water Pipe as Per IS-13592 of 90mm Dia. 375.00 Rmt. 302.54 Rs. Three Hundred

Complete with Special Flings, Compressor type Fittings, Wall clips on wooden patty Two & Paise Fifty

including making good the ceiling and floor on terrace rain water pipe shall be 90 Four Only

mm Dia. SWR horizontal pipe and vertical pipe and 90mm bend at the end near by

Ground level rate are Inclusive of all Necessary Fittings required for ALL FLOORS.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

89 Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) 127.00 Rmt. 206.73 Rs. Two Hundred

PIPE having National Sanitation Foundation (NSF) seal For Portable Water of 20 Six & Paise Seventy

mm. dia. nominal bor tube fitting and clamps including making good the wall, Three Only

ceiling and floor etc. all Material Complete must be used Approved Material list of

90 Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) 146.00 Rmt. 251.31 Rs. Two Hundred

PIPE having National Sanitation Foundation (NSF) seal For Portable Water of 25 Fifty One & Paise

mm. dia. nominal bor tube fitting and clamps including making good the wall, Thirty One Only

ceiling and floor etc. Complete all Material Complete must be used Approved

Material list of GSPHCL.

91 Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) 177.00 Rmt. 443.29 Rs. Four Hundred

PIPE having National Sanitation Foundation (NSF) seal For Portable Water of 40 Forty Three & Paise

mm. dia. nominal bor tube fitting and clamps including making good the wall, Twenty Nine Only

ceiling and floor etc. Complete all Material Complete must be used Approved

Material list of GSPHCL.

92 Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) 499.00 Rmt. 654.04 Rs. Six Hundred

PIPE having National Sanitation Foundation (NSF) seal For Portable Water of 50 Fifty Four & Paise

mm. dia. nominal bor tube fitting and clamps including making good the wall, Four Only

ceiling and floor etc. Complete all Material Complete must be used Approved

Material list of GSPHCL.

93 Providing & fixing concealed center point to wall celing & floor CPVC pipes (SDR- 50.00 Rmt. 1312.94 Rs. One Thousand

13.5) Pipe having National Sanitation Foundation (NSF) seal for potable water of Three Hundred

following inside dia. Nominal Bore Tube fitting & clamps including making good Twelve & Paise

the wall, ceiling and floor etc. complete. (v) 65mm dia.all Material Complete must Ninety Four Only

be used Approved Material list of GSPHCL.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

94 Providing & fixing concealed center point to wall celing & floor CPVC pipes (SDR- 80.00 Rmt. 1763.13 Rs. One Thousand

13.5) Pipe having National Sanitation Foundation (NSF) seal for potable water of Seven Hundred

following inside dia. Nominal Bore Tube fitting & clamps including making good Sixty Three & Paise

the wall, ceiling and floor etc. complete. (v) 80mm dia.all Material Complete must Thirteen Only

be used Approved Material list of GSPHCL.

95 Provinding and laying inegrated cement based proofing treatment of required 1265.00 Sqm 912.71 Rs. Nine Hundred

thickness over the roof including 10mm thick waterproofing cement plaster in Twelve & Paise

cement plaster in cement mortar1:3 and chaina mosaic fitting and finally finishing Seventy One Only

the surfase with white cement slurry and slopping out taerrace slabs with following

specification laid to required slope not flatter than 1:80 ( the thickness of water

proofing treatment near rainwater outlet or the lowest point of the finishedslope

shall not be less then 45mm, including treating the vertical surfaseof the parapet

wall up to 20cms . height above finished level of terracing including finishing the

top with joint less water proofing plaster , curing , testing etc. complete. Rate is

including ten years performance of guarantee bond to be given on stamp paper. (No

extra shall be paid for increase in thickness for proper slope).

(A) Applying and grouting a slurry coat of neat cemnt using 2.75 kg/Sqm. of

cement admixed with properly water proofing compound conforming to IS -2645

and 10 mm thick water proofing cement plaster in Cement mortar 1:3 over the

R.C.C.slab incl. cleaning the surface before treatment

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

(B) Layign cement corcretre using broken brick bats 25mm to 40mm size with 50%

of cement mortar 1:4 (1cement :4 coarse sand ) over 10mm thick water proofing

cement plaster in cement mortar 1:3 (1 cement ,3 coarse sand) admixed with

proprietary water proofing compound conforming to IS 2645 to required slope and

treating similarly the adjoining walls up to 200mm height incl. rouding of junction

C) After Two Days of proper curing applying a second floor of cement slurry

(D) Finishing the surface with china mosaic pieces laid on 10mm thick joint less

cement plaster of mix 1:3(1 cement :3 coarse sand )admixed with proprietary water

proofing compound conforming to IS :2645 and finally finishing the surface with

trowel with neat cement slurry

(E) The whole terrace so finished shall be flooded with water for a minimum period

of two weeks for curring for final taste

All above operation to be done in order and as directed and specified by the

Engineer In Charge.

96 Providing, Fabricating and fixing M.S. GRILL/GATE of approved pattern fabricated 207622.00 Kg. 75.02 Rs. Seventy Five &

from M.S. flat,square bars, round bars,c-channel, box pipe as per detail Drawings. Paise Two Only

Rate is inclusive of welding with grinding smooth surface, two coats of Oil paint

and one coat of yellow Zinc primer coat of approved brand only.oil paint shall be

used as per approved materisl list of GSPHCL structure steel must be ISI make Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

97 Steel work, welded in built up sections framed work 9000.00 Kg. 90.18 Rs. Ninety & Paise

including cutting, hoisting, fixing in position and applying a priming coat of red Eighteen Only

lead paint. (A)In beams and joists, channels angles Tees, flats, with connecting plates

or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to

common rafters and primer, paint shall be used as per Approved material list at

GSPHC ( for any Height )

98 Providing & Fixing Urinal with P.V.C water pipe, 32mm dia. C.P. brassa waste 6.00 Nos 2098.98 Rs. Two Thousand

coupling with Connection 32mm dia waste Pipe etc. Complete. Rate are inclusive of Ninety Eight &

all matreials, Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Paise Ninety Eight

Specifications and as per the Instruction of Engineer In charge. The Model & Make Only

of Urinal Shall be as per the Approved Make List of GSPHCL.

99 S.S. Railing. Providing and Fixing of Stainless Steel 304 grade Pipe Railing 0.90mt. 59.00 Rmt 3143.43 Rs. Three

Height. Top Round Pipe (Baluster) of 2" dia. Vertical balustrade 1.5" x 1.5" at every Thousand One

max. 0.90mt. c/c and intermediate 3 nos. runners pipe mid rail of 1" dia. and S.S. Hundred Forty

base plate of 100 x 8mm. The Railing system shall be floor mounted with anchor Three & Paise Forty

fastener and base plate of 100mm size having 8mm thickness completed as per Three Only

detailed drawing & as directed by engineer in charge. Rate are inclusive of all

material, labour, taxes & polishing.

100 Providing and fixing Single Hole Wash Basin with C.I. or M.S. brackete & M.I. fisher 23.00 No 3935.33 Rs. Three

union, P.V.C. water pipe with connection from Stop Cock to Pillar Tap, PVC Bottle Thousand Nine

trap with connection 32mm dia. C.P. brass waste coupling etc. complete. Rate are Hundred Thirty

inclusive of all materials, Labour & Necessary Fittings etc. Complete as per Detailed Five & Paise Thirty

Drawings, Specifications and as per instruction of Engineer In Charge. The Model & Three Only

Make of Wash Basin Shall be as per the Approved Make List of GSPHCL.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

101 Providing & Fixing Single Hole Table Top Wash Basin on Granite Slab with C.I or 6.00 No 5917.93 Rs. Five Thousand

M.S. brackete & M. I . fisher union, P.V.C water pipe with Connection from Stop Nine Hundred

Cock to Pillar Tap, PVC Bottle Trap with Connection 32mm dia. C.P. brassa waste Seventeen & Paise

coupling etc. Complete. Rate are inclusive of all matreials, Labour & Necessary Ninety Three Only

Fittings etc. Complete as per Detailed Drawings, Specifications and as per the

Instruction of Engineer In charge. The Model & Make of Table Top Wash Basin Shall

be as per the Approved Make List of GSPHCL.

102 Providing & fixing PVC SWR MULTY NANHI TRAP IS:14735 for drain -100mm 34.00 No 1122.26 Rs. One Thousand

dia. With jali of following nominal dia. Of self cleansing design with C.I. Screwed One Hundred

down or Hinged grating including the cost of cutting and making good the walls. Twenty Two &

Rate are inclusive of all necessary fittings, material, labour etc.complete as per Paise Twenty Six

direction of Engineer In charge. Only

Providing & Fixing Floor drain jali (Glossy Finish) (on N.T.) of 6" X 6"size made of

Stainless Steel Grade 304 Floor Drain 3 Piece (Cover/Jali/Grating) With Anti

Cockroach Bowl on N.T. Rate are inclusive of all necessary fittings, material, labour

etc.complete as per direction of Engineer In charge.

103 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter 8.00 No 566.65 Rs. Five Hundred

with jali of the following nominal diameter of self cleansing design with C.I scread Sixty Six & Paise

down or hinged grating including the cost of cutting and making good the walls. Sixty Five Only

104 Provinding and fixing SW gully trap with out CI grating brick masonary chamber 25.00 No 1176.94 Rs. One Thousand

and water tight CI cover with frame of 300*300mm size inside with standard weight One Hundred

(I) Square mouth traps ©150*100mm size P or R type Seventy Six & Paise

Ninety Four Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

105 Providing & Fixing ANGLE COCK. Rate are inclusive of all materials, Labour & 42.00 No 665.51 Rs. Six Hundred

Necessary Fittings etc. Complete as per Detailed Drawings, Specifications and as per Sixty Five & Paise

the Instruction of Engineer In Charge. The Model & Make of ANGLE COCK shall be Fifty One Only

as per the Approved Make List of GSPHCL.

106 Provinding and fixing in position PVC COWEL VENT to pipe 75 mm dia directed. 26.00 No. 16.47 Rs. Sixteen & Paise

Forty Seven Only

107 Provinding and fixing in position PVC COWEL VENT to pipe 110 mm dia directed. 24.00 No. 28.16 Rs. Twenty Eight &

Paise Sixteen Only

108 Providing and fixing acrylic sheet with Vinyl letter colour -2073 - dark grey for bak 11.00 Sqm 7193.88 Rs. Seven

ground and colour -2199 - white letter with required scroo ..etc as per required Thousand One

sizes complete etc as per specification.& instruction of Engineer Incharge. Hundred Ninety

Three & Paise

Eighty Eight Only

109 Providing and fixing G.I.Rain Water Spout of 50mm Dia. and 30Cm Length 19.00 No 100.90 Rs. One Hundred

& Paise Ninety

110 Providing & Fixing 15mm One way Bib Tap with wall flange. Rate are inclusive of 53.00 No 990.61 Rs. Nine Hundred

all materials, Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Ninety & Paise

Specifications and as per the Instruction of Engineer In Charge. The Model & Make Sixty One Only

of Bib Tap shall be as per the Approved Make List of GSPHCL.

111 Providing & Fixing Two Way Bib Tap with Wall Flange. Rate are inclusive of all 27.00 No 1309.39 Rs. One Thousand

materials, Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Three Hundred

Specifications and as per the Instruction of Engineer In Charge. The Model & Make Nine & Paise Thirty

of Two way Bib Tap shall be as per the Approved Make List of GSPHCL. Nine Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

112 Providing a I.S.I. mark 7 levers three key brass pad lock of NAVATAL (Godrej) 54.00 No 243.64 Rs. Two Hundred

make 65mm dia on completion of project. Forty Three & Paise

Sixty Four Only

113 Finishing Ceilling/Slop Surface with Plastic Emulsion Paint on Ceilling/Slop 1268.00 Sqm 188.49 Rs. One Hundred

Surface (two coats) to give an required shap even shade after throughly brushing Eighty Eight &

the surface to remove all dirt and remains of loose poweder material etc. complete. Paise Forty Nine

Rate are inclusive of applying two coat of lapy (Putty) and one coat of primer on Only

new Ceilling/Slop Surface to give and even shade including thoroughly brushing

the surface free from mortar dropping and other foreign matter and sand papered

smooth. Fine Putty, primer , plastic emulsion paint shall be used as per approved

material list by GSPHCL ( For all floor ).

114 Finishing Wall with Plastic Emulsion Paint on Wall Surface (two coats) to give an 4147.00 Sqm 177.96 Rs. One Hundred

required shap even shade after throughly brushing the surface to remove all dirt Seventy Seven &

and remains of loose poweder material etc. complete. Rate are inclusive of applying Paise Ninety Six

two coat of lapy (Putty) and one coat of primer on new wall surface to give and Only

even shade including thoroughly brushing the surface free from mortar dropping

and other foreign matter and sand papered smooth. Fine Putty, primer , plastic

emulsion paint shall be used as per approved material list by GSPHCL ( For all floor

115 Finishing wall with weather proof exterior emulsion paint on wall surface (two 3521.00 Sqm 150.52 Rs. One Hundred

coats) over and above applying One Coat Of Primer to give an required shape even Fifty & Paise Fifty

shade after thoroughly brushing the surface to remove all dirt, and remains of loose Two Only

powdered materials.etc complete.Primer, Exterior emulsion paint shall be used as

per approved material list by GSPHCL ( For any height ).

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

116 S.S. Railing. Providing and Fixing of Stainless Steel 304 grade Pipe Railing 0.90mt. 18.00 Rmt 3507.80 Rs. Three

Height. Top Round Pipe (Baluster) of 2" dia. Vertical balustrade 1.5" x 1.5" at every Thousand Five

max. 0.90mt. c/c and intermediate 4 nos. runners pipe mid rail of 1" dia. and S.S. Hundred Seven &

base plate of 100 x 8mm. The Railing system shall be floor mounted with anchor Paise Eighty Only

fastener and base plate of 100mm size having 8mm thickness completed as per

detailed drawing & as directed by engineer in charge. Rate are inclusive of all

material, labour, taxes & polishing.

117 Providing, supplying & fixing Stainless steel letters(30.00cmt Height & 4.50cmt 22.00 Nos 952.62 Rs. One Thousand

wide) 304 grade with spraying colour on surface etc. complete as directed. Size of Fifty Six & Paise

the S.S. letters shall be as described in tender item. Coating of the S.S. letters shall be Fifty Two Only

as directed by engineer in charge. Letter shall be fixed at any height as directed by

engineer in charge.

118 Providing & Fixing S.S. Cloth Hanger (5 Hook). Rate as per detail drawing and as 23.00 No 249.85 Rs. Two Hundred

directed by engineer in charge.Rate are inclusive of all materials, Labour & Forty Nine & Paise

Necessary Fittings etc. Complete as per Detailed Drawings, Specifications and as per Eighty Five Only

the Instruction of Engineer In Charge. The Model & Make shall be as per the

Approved Make List of GSPHCL.

119 Providing & Fixing Health faucets (ABS body). Rate are inclusive of all materials, 27.00 No 565.51 Rs. Five Hundred

Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Specifications Sixty Five & Paise

and as per the Instruction of Engineer In Charge. The Model & Make of Health Fifty One Only

Faucets shall be as per the Approved Make List of GSPHCL.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

120 Providing & Fixing 25mm Concealed Heavy Duty Stop Cock with Exposed Part & 25.00 No 1233.57 Rs. One Thousand

Other Accessories (Sleeve, Lever, Wall Flange) . Rate are inclusive of all matreials, Two Hundred

Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Specifications Thirty Three &

and as per the Instruction of Engineer In charge. The Model & Make of Concealed Paise Fifty Seven

Heavy Stop Cock Shall be as per the Approved Make List of GSPHCL. Only

121 Providing & Fixing 15mm Concealed Heavy Duty Stop Cock with Exposed Part & 29.00 No 942.54 Rs. Nine Hundred

Other Accessories (Sleeve, Lever, Wall Flange) . Rate are inclusive of all matreials, Forty Two & Paise

Labour & Necessary Fittings etc. Complete as per Detailed Drawings, Specifications Fifty Four Only

and as per the Instruction of Engineer In charge. The Model & Make of Concealed

Heavy Stop Cock Shall be as per the Approved Make List of GSPHCL.

122 Providing & fixing TEAK WOOD DOOR FRAME PATTI 40mm x 10mm thick as per 114.00 Rmt 71.01 Rs. Seventy One &

per Detail drawigs and as directed by Engineer in charge. Rate are inclusive of all Paise One Only

material, labour, Taxes.

123 MOULDING OF KOTA STONE/GRANITE STAIR TRADE COMPLETE AS PER 348.00 Rmt 129.95 Rs. One Hundred

DIRECTION OF ENGINEER IN CHARGE FOR ALL FLOOR Twenty Nine &

Paise Ninety Five

124 PRO. 3 NOS GROOVE IN TOTAL LENGTH OF STAIRCASE TREAD OF SIZE 348.00 Rmt 82.80 Rs. Eighty Two &

10MM*10MM FINISHED SMOOTH IN PARALLEL LINE , EQUALLY SPACED AS Paise Eighty Only

PER DIRECTION OF ENGINEER IN-CHARGE IN ALL TYPE OF FLOORING

ETC. COMPLETE FOR ALL FLOOR.

125 Providing & Fixing Towel Rod. Rate are inclusive of all materials, Labour & 3.00 No. 1078.70 Rs. One Thousand

Necessary Fittings etc. Complete as per Detailed Drawings, Specifications and as per Seventy Eight &

the Instruction of Engineer In Charge. The Model & Make of Towel Rod shall be as Paise Seventy Only

per the Approved Make List of GSPHCL.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

126 Providing and Fixing Gun Metal handle valve with all necessary fittings 50 MM DIA 10.00 No 2302.33 Rs. Two Thousand

all materials must be of approved by makelist of GSPHCL. Three Hundred

Two & Paise Thirty

Three Only

127 Providing and Fixing Gun Metal handle valve with all necessary fittings 40 MM DIA 16.00 No 656.86 Rs. Six Hundred

all materials must be of approved by makelist of GSPHCL. Fifty Six & Paise

Eighty Six Only

128 Providing & Fixing Wall Hung with PVC Flush Tank, Soft Seat Cover & intergal "P" 27.00 No 5470.90 Rs. Five Thousand

or "S" Trap including Jointing the Trap with Pan and Soil pipe. Wall hung shall be Four Hundred

fixed on S.S heavy duty rack bolt having 16mm dia, 165mm length using Plastic Seventy & Paise

sleeve Make by Using Drill Bitt Only. Rate are inclusive of all matreials, Labour & Ninety Only

Necessary Fittings etc. Complete as per Detailed Drawings, Specifications and as per

the Instruction of Engineer In charge. The Model & Make of Wall Hung & Flush

Tank Shall be as per the Approved Make List of GSPHCL.

129 Providing & Fixing water closet squatting pan (Orrissa Type W.C. Pan) size 580mm 16.00 No 1012.15 Rs. One Thousand

first quality including necessary "P" or "S" Trap, Including, jointing the trap with Twelve & Paise

pan & Soil pipe or PVC Trap with PVC connector, M.S. Clamp etc. in vitreous china Fifteen Only

white colour. Joints shall be sealed by pipe sealent.

130 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 7.00 No 846.12 Rs. Eight Hundred

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge Forty Six & Paise

with C.P. brass screws and washers. Twelve Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

131 Providing & Fixing Towel Ring. Rate are inclusive of all matreials, Labour & 7.00 No 909.08 Rs. Nine Hundred

Necessary Fittings etc. Complete as per Detailed Drawings, Specifications and as per Nine & Paise Eight

the Instruction of Engineer In charge. The Model & Make of Towel Ring Shall be as Only

per the Approved Make List of GSPHCL.

132 Providing & fixing WPC DOOR PATTI 24mmx6mm thick as per per Detail drawigs 74.00 Rmt 57.02 Rs. Fifty Seven &

and as directed by Engineer in charge. Rate are inclusive of all material, labour, Paise Two Only

133 Providing Supplying and fixing Single Pipe Bracket System with U Bolt Rubber 240.00 No 182.83 Rs. One Hundred

Mounted for Pipe supporting clamping system for external vertical Fixed line with Eighty Two & Paise

wall distance 3" including nuts, bolts, fasterners etc complete as per detailed Eighty Three Only

specification and as directed by Engineer in charge.

134 Providing Supplying and fixing S4 Channel system ( S4 channel + Profile Bracket + 285.00 No 421.58 Rs. Four Hundred

U Bolt Rubber Mounted System) for multiple pipes for external vertical fixed line Twenty One &

with wall distance 3" including nuts, bolts, fasterners etc complete as per detailed Paise Fifty Eight

specification and as directed by Engineer in charge. Only

135 Providing & fixing hydraulic door closer of approved size and made such as 11.00 No. 1585.00 Rs. One Thousand

EVERITE/HYPER/EGL/GODREJ or equivalent as directed. All lift, level and leads. Five Hundred

Eighty Five Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

136 Providing,Supplying & Laying (to level or slopes) ISI Standard Heavy duty non- 280.00 Rmt 624.00 Rs. Six Hundred

pressure pipes I.S. class NP3 Test Pressure 0.7kg/sq.cm RCC Pipes(of sulfate Twenty Four Only

resisting cement)in standard length of following class & diameter suitable for either

collar joints or rubber ring joints including all

taxes,insuarance,transpoartation,freightcharges,octroi,inspection

charges,loading,unloading,conveyance to departmental stores stacking etc

complete.(D)250mm

137 Providing, supplying and Fixing Corrugated DWC HDPE Pipes of Class SN8 146.00 Rmt 229.00 Rs. Two Hundred

Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and Twenty Nine Only

elastomeric sealing ring) with non-smooth External Annular Corrugated and

Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage &

Drainage application as per EN:13476-3 including all local and central taxes,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete. (100mm ID Dia) Including

Lowering, laying and jointing of class SN 8 structured wall ( External Annular

Corrugated & Smooth Internal surface) Polyethylene Piping and fittings with the

help of coupler ( on line / off line ) attached with one end of pipes, sliding over the

elastomeric sealing rubber ring placed on the specified valley of the corrugation at

the spigot end, lowering the same into the trench, laying on the lower bedding

(constructed at bottom of trenches) at prescribed gradient,depth & alignment

,testing the water tightness of the joints, ensuring the continuity tests of specified

pipe segments etc. complete as per drawing,specifications & detailed engineering,

including carriage of pipes & fittings from site stacks to the place of laying etc. as

per direction of Engineer-in-charge.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

138 Providing, supplying and fixing Corrugated DWC HDPE Pipes of Class SN8 488.00 Rmt 396.00 Rs. Three Hundred

Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and Ninety Six Only

elastomeric sealing ring) with non-smooth External Annular Corrugated and

Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage &

Drainage application as per EN:13476-3 including all local and central taxes,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete. (150 mm ID Dia) Including

Lowering, laying and jointing of class SN 8 structured wall ( External Annular

Corrugated & Smooth Internal surface) Polyethylene Piping and fittings with the

help of coupler ( on line / off line ) attached with one end of pipes, sliding over the

elastomeric sealing rubber ring placed on the specified valley of the corrugation at

the spigot end, lowering the same into the trench, laying on the lower bedding

(constructed at bottom of trenches) at prescribed gradient,depth & alignment

,testing the water tightness of the joints, ensuring the continuity tests of specified

pipe segments etc. complete as per drawing,specifications & detailed engineering,

including carriage of pipes & fittings from site stacks to the place of laying etc. as

per direction of Engineer-in-charge.

139 Constructing brick masonry chamber for under ground C.I. inspection chamber and 41.00 No 3793.18 Rs. Three

bends with brick having crushing strength not less than 35 kg./cm2 in C.M. 1.5 Thousand Seven

precast R.C.C. cover 1:1.5:3 of size 455 x 610 mm internal dimenslons. R.C.C. top Hundred Ninety

slab with C.C. 1:1.5:3 mix (1 Cement : 1.5 coarse sand :3 graded stone aggregate Three & Paise

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement Eighteen Only

mortar 1:3 finished smooth with a floating coat of neat cment walls & bed connect

etc. complete rate inclusive of outside plaster of 15mm thick in cm 1:3 form top of

chamber and all side up to 15 cm deep below ground level. rate also inclusive of

providing and fixing precast cover of size 0.7 m x 0.5 x .07 m with 2 no of m.s. flat

handle in cement concrete 1:1.5:3.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

140 Extra over above item for additional depth of 0.1 m or part thereof beyond 28.00 No 239.99 Rs. Two Hundred

450mm depth for brick masonary chamber for (I) 610 x 455 mm Thirty Nine & Paise

Ninety Nine Only

141 Constructing brick masonry chamber for under ground C.I. inspection chamber and 28.00 No 5476.93 Rs. Five Thousand

bends with brick having crushing strength not less than 35 kg./cm2 in C.M. 1.5 Four Hundred

precast R.C.C. cover 1:1.5:3 of size 600 x 850 mm internal dimenslons. R.C.C. top Seventy Six & Paise

slab with C.C. 1:1.5:3 mix (1 Cement : 1.5 coarse sand :3 graded stone aggregate Ninety Three Only

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of neat cment walls & bed connect

etc. complete rate inclusive of outside plaster of 15mm thick in cm 1:3 form top of

chamber and all side up to 15 cm deep below ground level. rate also inclusive of

providing and fixing precast cover of size 0.7 m x 0.95 x .07 m with 2 no of m.s. flat

handle in cement concrete 1:1.5:3.

142 Extra over above item for additional depth of 0.1 m or part thereof beyond 18.00 No 322.37 Rs. Three Hundred

450mm depth for brick masonary chamber for (I) 600 x 850 mm Twenty Two &

Paise Thirty Seven

143 Providing and constructing Sewer Manholes, scraper manholes and unit house 6.00 No 12179.00 Rs. Twelve

connection chamber, as per the type design in brick masonary in C.M. 1:5 and inside Thousand One

and outside 20mm thick plastering in CM 1:3 necessary 100mm coping with Hundred Seventy

reinforcement in RCCM 200 fixing C.I. steps and fixing manhole frame and covers Nine Only

(But exculding supply of manhole frame and covers)over manholes and house

connection chambers and fixing Manholes covers (but exculding supplying of

manhole covers) over scraper manhole etc. complete.Providing and fixing safety

chain wherever necessary as per the stipulations in the type design complete as per

latest CPHEEO manual.(Excl.Excavation). (a)Manhole type "A" Circular type having

inside Daimeter of 1200mm for depth upto 1.50m depth (for 150mm to 500 mmdia

sewer) 1)Manhole tpe "A" as above but upto 1.0m Depth

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

144 Providing and constructing Sewer Manholes, scraper manholes and unit house 6.00 Rmt 6628.00 Rs. Six Thousand

connection chamber, as per the type design in brick masonary in C.M. 1:5 and inside Six Hundred

and outside 20mm thick plastering in CM 1:3 necessary 100mm coping with Twenty Eight Only

reinforcement in RCCM 200 fixing C.I. steps and fixing manhole frame and covers

(But exculding supply of manhole frame and covers)over manholes and house

connection chambers and fixing Manholes covers (but exculding supplying of

manhole covers) over scraper manhole etc. complete.Providing and fixing safety

chain wherever necessary as per the stipulations in the type design complete as per

latest CPHEEO manual.(Excl.Excavation).(a)Manhole type "A" Circular type having

inside Daimeter of 1200mm for depth upto 1.50m depth (for 150mm to 500 mmdia

sewer) 1)Extra depth beyond 1.0mt but upto 1.5mt depth for Manhole type "A" as

145 Providing and constructing Sewer Manholes, scraper manholes and unit house 4.00 No 21116.00 Rs. Twenty One

connection chamber, as per the type design in brick masonary in C.M. 1:5 and inside Thousand One

and outside 20mm thick plastering in CM 1:3 necessary 100mm coping with Hundred Sixteen

reinforcement in RCCM 200 fixing C.I. steps and fixing manhole frame and covers Only

(But exculding supply of manhole frame and covers)over manholes and house

connection chambers and fixing Manholes covers (but exculding supplying of

manhole covers) over scraper manhole etc. complete.Providing and fixing safety

chain wherever necessary as per the stipulations in the type design complete as per

latest CPHEEO manual.(Excl.Excavation).(b)Manhole type "B" Circular type having

inside Daimeter of 1500mm for depth upto 1.50m to 4.00mt depth (for 150mm to

mmdia sewer) 1)Manhole tpe "B" as above but upto 1.5m Depth

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

146 Providing and constructing Sewer Manholes, scraper manholes and unit house 4.00 Rmt 12313.00 Rs. Twelve

connection chamber, as per the type design in brick masonary in C.M. 1:5 and inside Thousand Three

and outside 20mm thick plastering in CM 1:3 necessary 100mm coping with Hundred Thirteen

reinforcement in RCCM 200 fixing C.I. steps and fixing manhole frame and covers Only

(But exculding supply of manhole frame and covers)over manholes and house

connection chambers and fixing Manholes covers (but exculding supplying of

manhole covers) over scraper manhole etc. complete.Providing and fixing safety

chain wherever necessary as per the stipulations in the type design complete as per

latest CPHEEO manual.(Excl.Excavation).(b)Manhole type "B" Circular type having

inside Daimeter of 1500mm for depth upto 1.50m to 4.00mt depth (for 150mm to

mmdia sewer)(1)Extra depth beyond 1.5mt but upto 4.0mt depth for Manhole type

"B" as above

147 RCC precast M.H. Frame Manufacture, supply & delivery at store or at site of wprk 11.00 No 1121.00 Rs. One Thousand

precast RCC M-200 frame suitable to drainage M.H. and as per type design & One Hundred

drawing including cost of reinforcement M.S. Angles or flat, curing mold work etc. Twenty One Only

(a) Heavy Duty Frame suitable for 50cm opening of Man hole.

148 RCC precast Cover Manufacture, supply & delivery at store or at site of wprk 11.00 No 1173.00 Rs. One Thousand

precast RCC M-200 Cover suitable to drainage M.H. and as per type design & One Hundred

drawing including cost of reinforcement M.S. Angles or flat, curing mold work etc. Seventy Three Only

(a) Heavy Duty Cover suitable for 50cm opening of Man hole.

149 Providing and fixing ball cock of approved quality as directed. (A) Copper Metal 4.00 Each 187.96 Rs. One Hundred

ISI Mark. (ii) 50 mm dia. Eighty Seven &

Paise Ninety Six

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

150 Providing & fixing in position ISI marked Rotational moulded Polyethylene double 94500.00 Ltr 3.91 Rs. Three & Paise

layer cylindrical vertical storage tank (IS : 12701) water tank size inlcuding making Ninety One Only

inlet and outlet. Over flow and washout arrangement with G.I. connection inlcuding

using necessary M.H. for connection etc. complete with closed cover including

applying two coats of oli painting outside the tank etc.complete.

151 Box cutting the road surface to proper slope and camber for making slope and 603.00 Cum. 105.75 Rs. One Hundred

camber for making a base for road work including removing the excavated stuff and Five & Paise

depositing on the road side slope as directed upto 50 Mt. lead. Seventy Five Only

152 Providing , supplying & Laying Granular Sub base ( GSB) by providing couarse 201.00 Cum. 1074.89 Rs. One Thousand

graded material , spreading in uniform layer with motor grader on prepared surface Seventy Four &

mixing by mix in place method with rotavator at OMC and compacting with Paise Eighty Nine

vibratory roller to achieve the desired density complete as per morth specification Only

153 Rolling and consolidation water bound macadam (except laterite and 2009.00 Sqm. 25.51 Rs. Twenty Five &

Kankar)including watering not exceeding 150 mm thickness (Main layer including Paise Fifty One

binding materials) including filling in depression which occur during the process. Only

(b) With power roller exceeding 8 tonne and not exceeding 12 tonne.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

154 Construction of concrete using trimix system having of any thickness M-250 302.00 Cum. 4347.62 Rs. Four Thousand

concrete mix with providing and fixing & removing of "C" channel having size Three Hundred

75mm x 75mm as per required level slope and thickness of concrete road floor Forty Seven &

leveling of place concrete with surface vibrator machine, dewatering system device Paise Sixty Two

finishing with power floater machine and trowel light brooming on the surface as Only

directed with providing expansion joint size 20 x 190mm using of concrete cutter

machine inc curing etc.complete.rate are also inclusive of providing and mixing

plastisizer of approved make in proportion as per mix design .

155 Providing & making & Cutting the road surface of any required depth & thickness 800.00 Rmt. 36.80 Rs. Thirty Six &

with machine cutter & fiiling it with sealant etc. complete as per direction of Paise Eighty Only

Engineer incharge.

156 Providing and fixing pre-cast Rubber Dye/ Steel Dye inter locking concrete block 30.00 Sqm 697.20 Rs. Six Hundred

60mm thick grade of concrete M300 pnumatic compressed/vibrated mechanically Ninety Seven &

and as per approved design Conforming to IS 15658:2006 including 35mm sand Paise Twenty Only

layer for levelling and filling the joint with sand in proper line and level as per

guidelines of IRC: SP 63-2018 etc. complete.

157 Providing and fixing pre-cast concrete kerb stone of gray cement based concrete 20.00 Rmt. 367.01 Rs. Three Hundred

block 30cm length, 30cm height and 15cm thick of M250 grade concrete as per Sixty Seven & Paise

approved design and including excavation for fixing in proper line and level, filling One Only

the joint with C:M 1:3 (1cement :3fine sand) etc complete.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

158 Providing, fixing, testing and commissioning of " C" class Heavy Duty G.I pipe

Confirming as per IS: 1239 including welding ,cutting, fittings like elbows, tees,

flanges, tapers , Nuts , bolts, gaskets etc. and Fixing the Pipes on the walls/ceilings

with Suitable Clamp/Supports Frame and painting of one coat of primer and 2 or

more coats of synthetic enamel paint of approved make/shade complete as per

specification

(A) 200 mm dia 5.00 Rmt 4248.53 Rs. Four Thousand

Two Hundred

Forty Eight & Paise

Fifty Three Only

(B) 150 mm dia 10.00 Rmt 1799.49 Rs. One Thousand

Seven Hundred

Ninety Nine &

Paise Forty Nine

(C)100 mm dia. 140.00 Rmt 1367.29 Rs. One Thousand

Three Hundred

Sixty Seven & Paise

Thirty Nine Only

(D)25 mm dia. 3.00 Rmt 474.95 Rs. Four Hundred

Seventy Four &

Paise Ninety Five

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

159 Providing, laying, testing & commissioning of "C" Class Heavy Duty G.I. pipe

Confirming IS 1239 fittings likes elboes, tees, flanges, tapers, nuts, bolts, gaskets etc

in ground including welding, excavation & providing cement concrete blocks as

supports, anticorrosive treatment with coltar/asphalt tapeas per IS 10221 or

Wrapping coating material 4mm thick on pipe , refilling the treanch etc. complete as

per direction of engineer in charge.

(A) 150 mm dia 10.00 Rmt 2561.95 Rs. Two Thousand

Five Hundred Sixty

One & Paise Ninety

160 Supply and installation,testing and commisioning of Butterfly valves of PN

ratings with bronze/gunmetal seat duly ISI marked complete with nuts, bolts,

washers, gaskets confirming to IS 13095 of following sizes as required:

(A)100 mm dia. 7.00 Nos. 6101.15 Rs. Six Thousand

One Hundred One

& Paise Fifteen

161 Providing, installing testing & commissioning of NRV of following sizes confirming 0.00

to IS 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required.

(A)100 mm dia. 7.00 Nos. 9945.68 Rs. Nine Thousand

Nine Hundred

Forty Five & Paise

Sixty Eight Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

162 Supplying & fixing single headed external yard hydrant valve with 1 no 63 mm dia 18.00 Nos. 5564.93 Rs. Five Thousand

instantaneous SS coupling and CI wheel, ISI marked, confirming to IS 5290 (Type A) Five Hundred Sixty

with blank gunmetal /SS cap and chain as required Five & Paise Ninety

Single headed stainless steel Three Only

163 Providing and fixing of 63 mm SS branch pipe nozzle conforming to IS 903, suitable 18.00 Nos 2854.62 Rs. Two Thousand

for instantaneous connections to hose coupling etc. as required Eight Hundred

25 mm Fifty Four & Paise

Sixty Two Only

164 Providing & fixing 63mm dia 15 m long RRL hose pipe with 63mm dia male and 18.00 Nos 3916.23 Rs. Three

femal couplings duly bound with GI wires, revates etc. confirming to IS 636 (typa- Thousand Nine

A) as required Stainless steel (grade 304) Hundred Sixteen &

Paise Twenty Three

165 Providing, fixing, testing and commissioning of Weather proof standard fire hose 18.00 Nos 2673.28 Rs. Two Thousand

cabinet wall mounting type(750mm x 600mm x 250 mm deep) having single opening Six Hundred

with M.S. Fabricated Stand, necessary locking arrangement by allan key suitable for Seventy Three &

housing 2 nos. hose pipe, 1no. Branch pipe & nozzle spaner. Paise Twenty Eight

166 Supplying and fixing specially designed SS 304 orifice plates (minimum 6 mm plate 18.00 Nos 1204.79 Rs. One Thousand

thickness) to be fitted between flange and landing valve of external & internal Two Hundred Four

hydrant outlets of hydrant valves for reducing delivery pressureto 3.5 kg/ sq.cm at & Paise Seventy

hydrant valve Nine Only

167 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post 18.00 Nos 7920.84 Rs. Seven

office red, confirming to IS 884 complete with the following as required. 25 mm Thousand Nine

nominal int. dia. Water hose thermoplastic (Textile reinforced) type-2 as per IS12585 Hundred Twenty &

25 mm nominal internal dia gun metal globe valve and nozzle. Drum and brackets Paise Eighty Four

for fixing the equipment of the wall. Connections from risers with 32 mm dia stop Only

gun metal valve & MS pipe and socket.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

168 SITC of test & drain assembly with all piping, sight glass, 25mm dia. test & drain 18.00 Set 6708.11 Rs. Six Thousand

valve etc complete 25 mm pipe - 5 mtr. (average), 2 ball valves , accessories per 1 Seven Hundred

assembly DSR (E&M) 2022, Item No. 18.7.1, Rate of Providing, laying, testing & Eight & Paise

commissioning of MS C Class 100 mm Pipe per mtr. (without GST as per RA of 4.1.8 Eleven Only

169 providing & fixing emergency escape signes/ printed on rigid PVC sheet / acrylic

sheet 4 mm thick photoluminescent auto glow type of approved quality including

fixing on door, wall, celling complete with installation as directed.

A. Signes 2500.00 SQ.INC 7.95 Rs. Seven & Paise

Ninety Five Only

170 Providing, fixing, testing and commissioning of 15 mm dia quartzoid bulb type 5.00 Nos. 503.01 Rs. Five Hundred

sprinklers of ratings 68 degree centigrade with required accessories: Three & Paise One

Pendent sprinkler Only

171 providing and fixing extruded Alluminium section 15 micron regular anodized 35.00 Sqm 1672.80 Rs. One Thousand

coting with matt finished and excellent outdoor Durablity partion with pagithy Six Hundred

glazed of 5mm clear float glass and partly both side pre laminated partly boared of Seventy Two &

12mm thick as per detailed drawing and Specification gasket of EPDM quality shall Paise Eighty Only

be provided for weather lighting along with silicon sealant of dow corning /GE

silicon /Wacker germany of equipment complete etc as Aprroved by architect

complete as per the following section of Jindal make or Equivalent.

(A) Total Amount of Civil Work Rs.

(A) Total Amount of Civil Work Rs.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

172-a Providing & erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm 255.00 Point 605.00 RS: Six

copper PVC insulted FRLSH wire with 1.5 sq. mm (green) copper PVC insulated Hundred Five

FRLS wire for earth continuity in FIA approved ISI mark medium class white only

colour 20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with

adhesive solution erected on/in Brick Wall / slab along with continuous G.I. fish

wire to draw wires and laid in approved manner zari for PVC pipe and boxes

shall be filled with cement mortar and finishing the surface to match the wall /

ceiling complete with approved make 5/6 Amp. ISI make modular type switch

and accessories mounted in 20 G. G.I. company fabricated metallic box covered

with appropriate front plate modules erected flushed with wall / ceiling with

necessary modular lamp holder / modular ceiling rose / HD Connector as

directed..(Deep Junction box 75mm depth if required)(Make & Model approved

by EIC and matching colour with switch and accessories) for concealed wiring.

Light point. Cat.-III.

Necessary sheet / tape / polythene / sand must be erected or filled in all box to

prevent mortar going into the box. Length of point wiring must not increase than

mtr. For that necessary switch boards and their locations must be finalised before

execution by agency otherwise payment will not be done for extra long point. (For

future extention, if required, agency has to erect one higher size metal box and

modular plate as per instruction of EIC. Cost of blank plate shall be paid as per

tender item) [This item include cleaning (inside/outside) of all G.I. switch boards,

electric point box, fan box, MCBDB & box cutting plaster finishing for modular plate

without any gap] (Conductor resistance should be as per IS:8130/1984)

172-b For Bell Point., Cat.-III 2.00 Point 605.00 RS: Six

Hundred Five

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

172-c For Fan Point (with 6 A. Modular type switch and two module hum free EME Five 64.00 Point 842.00 RS: Eight

step type Electronic fan regulator both having ISI mark) Cat.-IIl. Hundred Forty

172-d For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat.- 48.00 Point 636.00 RS: Six

IlI Hundred Thirty Six

172-e For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI 100.00 Point 321.00 RS: Three

mark) Cat.-IlI Hundred Twenty

173-a Providing and erecting Medium Class FIA approved and ISI mark white colour 470.00 Mtr. 24.00 RS: Twenty

(embossed) RIGID PVC PIPES of following size complete erected with necessary Four only

PVC fittings & Junction boxes fixed with adhesive solution & clamps on / in wall /

ceiling along with continuous fish wire to draw mains with necessary fittings and

junction boxes for following dia. (a) 20 mm. dia.

173-b 25 mm dia. 270.00 Mtr. 33.00 RS: Thirty

Three only

174-a Providing and laying Mains with FRLSH PVC Insulated wire ISI marked 1.1 KV 800.00 Mtr. 81.00 RS: Eighty

grade with FIA approved ISI mark medium class 20/25/32 mm dia. embossed One only

rigid PVC pipe with PVC fitting fixed with adhesive solution to be erected on/in

brick wall / slab along with continuous G. I. fish wire to draw mains laid in

approved manner with plastering by cement mortar & finishing the surface to match

the wall / ceiling complete with FRLSH PVC insulated wire for earth continuity.

(Approved ISI make only) [a] 2 x 1.5 sq.mm. FRLS copper multi stranded conductor

mains with 1.5 sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. [conductor resistance should be as per IS:8130/1984]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

174-b 2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS 170.00 Mtr. 108.00 RS: One

copper multi stranded conductor for earthing as per standard colour code. Hundred Eight

174-c 2 x 4.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS 200.00 Mtr. 145.00 RS: One

copper multi stranded conductor earthing..As per standard colour code. Hundred Forty

Five only

174-d 2 x 6.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS 325.00 Mtr. 192.00 RS: One

copper multi stranded conductor for earthing as per standard colour code. Hundred Ninty

175 Providing & fixing 20 mm. dia. PVC insulated G.I. corrugated Flexible pipe with 40.00 Mtr 31.00 RS: Thirty

necessary socket, PVC bushes saddle, Check-nuts etc. complete of following sizes. One only

176 Providing & fixing 25 mm. dia. PVC insulated G.I. corrugated Flexible pipe with 90.00 Mtr. 37.00 RS: Thirty

necessary socket, PVC bushes saddle, Check-nuts etc. complete of following sizes. Seven only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

177 Providing and fixing Plug Point wiring with 1.1 KV grade ISI marked approved 25.00 Point 930.00 RS: Nine

make 2 x 2.5 sq.mm copper PVC insulated FRLSH wire with 1.5 sq.mm (green) Hundred Thirty

copper PVC insulated FRLSH wire for earth continuity in FIA approved ISI mark only

white colour medium class 20/25 mm dia. embossed rigid PVC pipe with PVC

fitting fixed with adhesive solution erected in wall/slab along with continuous G. I.

fish wire to draw wires and laid in approved manner zari for PVC pipe & boxes

shall be filled with cement mortar & finishing the surface to match the wall /

ceiling complete with 16 Amp Modular type Swich and accessories mounted in

G. GI company fabricated metallic box covered with appropriate front plate

modules erected flushed with wall. (a) 16 Amp. Indicator switch & 1 No. 6/16 A

universal socket white colour suitable for 3 pin top duly both having ISI mark.

(Necessary sheet / tape / polythene / sand must be erected or filled in all box To

Prevent Mortor Going In To The Box) Cat.-III

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

178 Providing and fixing Plug Point wiring with approved ISI marked 1.1 kv 2 x 4.0 3.00 Point 1087.00 RS: One

sq.mm copper PVC insulated FRLSH wire with 2.5 sq.mm (green) copper PVC Thousand Eighty

insulated FRLSH wire for earth continuity in FIA approved ISI mark white colour Seven only

medium class 20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with

adhesive solution erected in wall/slab along with continuous G.I. fish wire to draw

wires and laid in approved manner. zari for PVC pipe & boxes shall be filled with

cement mortar & finishing the surface to match the wall / ceiling complete with

No. 16/20 Amp. Modular type Swich and 1 no. 16/20 Amp. universal 3 pin socket

suitable for 3/5 pin top duty. [Both Having ISI mark must] mounted in 20 G. G.I.

company fabricated metallic box covered with appropriate front plate modules

erected flushed with wall.Above accessories will be erected combined or separately

as per site requirement and instruction of EIC. Cat.-III. (Necessary Sheet Must Be

Erected On All Box To Prevent Mortar Going Into The Box) (Conductor resistance

should be as per IS:8130/1984) (A.C. Point & Gyser Point) (Conductor resistance

should be as per IS:8130/1984)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

179 Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 8.00 Each 7025.00 RS: Seven

225 mm dia in soft soil. Suitable for doing pipe-in-pipe technology Thousand Twenty

earthing.Earthing electric rod must be made from Corrosion free Hot dip Five only

galvanizing pipes having following specification.

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B ' Class ISI mark of

Reputed Brand, Inner pipe:- 42 mm minimum O.D., Pipe B Class ISI mark reputed

Brand Terminal Size: 70mm X 100mm length, Terminal Should be made from inner

pipe for that pipe must be pressed and gave rectangular shape so its work as a

terminal.The hot deep galvanising must be done after above process.Galvanised

thickness must be minimum 75 micron any where. SS Nut bolt:- 2 no.with washer

suitable for 14mm dia. hole must be provided at terminal. total minimum

Weight(approx.) of earth electrodewith inside conductive material minimum

should be 26 kg.

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

(C) Back fill Compound:- Earthing compound should be capable to retain moisture

for long time Back Filling Compound weight is 25 Kg.

(D) Chamber and cover:- Earthing chamber should be size of 400 mm X 400 mm X

400 mm depth and Cover should be heavy duty cast iron with required size of

mm X 300 mm X 4 mm thick.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification only] [OEM

has to submit all detail & sample for approved before supplying]

[Water must be poured in bore before starting earthing. Earthing value must be

measured with earth tester. Agency has to bring the earth resistance to at least

ohms & voltage between neutral & Earthing upto 02 volt. Agency has to maintain

earthing & its value for one year. Earthing must be done in the presence of A.E.

180 For above earthing additional charges for boring in hard rock soil (by breaker) & 8.00 Each 325.00 RS: Three

filling soft soil in earth pit (certificate for soil have to given by DEE / AE along with Hundred Twenty

photographs) Five only

181 Supplying and erecting M.S./G.I. metal box having 16 Gauge painted with red 100.00 Sq. 5.81 RS: Five and

oxide be concealed in wall with necessary plastering & finishing with 3 mm thick Inch Paise Eighty One

laminated sheet with grooving as directed of following depth 3" depth. only

182-a Providing and erecting following type of Modular Type Accessories mounted with 6.00 Each 159.00 RS: One

20 G company fabricated metalic box, single mounting base frame covered with Hundred Fifty

textured / metallic front plate, modules erected with necessary connection. As Nine only

desired by Engineer in charge. TV Co-axial Socket outlet. Cat.-III.

182-b Blank Plate Single. Cat.-III 160.00 Each 25.00 RS: Twenty

Five only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

182-c (10) 6/16Amp. Universal socket 5.00 Each 198.00 RS: One

Hundred Ninty

Eight only

182-d (22) 16/20/25 Amp. Modular Starter for Motor / A.C. Unit Complete 5.00 Each 493.00 RS: Four

Hundred ninty

three only.

183 Providing & erecting following size of TV Co-axial flexible cable comprising inner 200.00 Mtr. 39.00 RS: Thirty

conductor of solid bare copper insulated with Foam PE & Secondary conductor Nine only

made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall

sheathed with black PVC insulation.[b] RG-6 [Polycab/ Finolex / RR Kabel Make]

184 Supplying & erecting approved make SMC press moulded composite FRP. loop- 7.00 Each 890.00 RS: Eight

in, loop-out approx. 2mm thick box complete with Bakelite connector strip Hundred Ninty

5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement only

having locking arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps& earth bolt of following size of

box.(A) 300mm x 200mm x 100mm [deep]

LIGHT FIXTURE / FAN

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

185 Supplying and Erecting LED indoor fitting having 1100mm long with LED of wattage Mashroom 125.00 Each 370.00 RS: Three

shape 0.2W to 0.5W assemble on single MCPCB with housing use as a heat sink shall be made from Hundred Seventy

white powder coating Aluminum extrusion having enough strength (sample must be approved by

EIC)with polycarbonate diffuser with following specification:

(A) Company mark/name on the fitting.

(B) Rated input voltage and frequency: 220V to 240 VAC ; 50Hz.

(C) Rated input wattage: max. 24w

(D) Rated input current : 0.2 Amp

(E) Power Factor : Min.

(F) ATHD :Max. 15%

(G) Rated Luminous flux: Min. 2420 lm

(H) CCT: 6500K

(I) CRI: Min. 80Ra

(J) Driver Efficiency: Min. 80%

(K) LED life span: Min. 50000 Hrs @ L70 (Certificate shall be attached)

(L) Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.

(M) Surge protection : Min. 2KV (N) IP rating: IP

(O) IK rating : IK

(P) Short circuit , Open circuit & Reverse Polarity Protection must be provided

(Q) Fixing Clamp min.12mm wide heavy duty design & strength should be sufficient to hold the

fitting erected on wall or ceiling (R) 3 core x 1.0 Sqmm

copper wire with min. 1ft (300mm) earthing connector.

(Note:-The manufacturer/ authorized Channel partner of the manufacturer has to submit 5 yrs free

replacement Guarantee for complete Fixture) [Approval will be given strictly subject to item

specification]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

186 SITC of Indoor Commercial Recess / Surface mounted (IP20) 24 W Cool/Natural 20.00 Each 751.00 RS: Seven

white/Warm (6K/4K) white Color back lit LED Down lighter with BIS approved Hundred Fifty One

separate potted driver with single piece pressure die cast aluminium alloy housing only

(no plastic part allowed) with corrosion resistant powder coated finish with

PMMA/PS/Injection moulded Polycarbonate diffuser with high brightness LED

complete (LED from Philips Lumileds, CREE, Nichia, Bridgelux, Seoul & Osram)

CRI > 80, CCT 6K/4K. The LED's should be mounted on back lit metal core PCB for

better heat conduction and long life of LED. Test report of shall be submitted (LM

for complete fixture, for individual LED). The Fixture have protection like

miswiring, over voltage, over load , IP20 wrong wiring, THD < 15%,, P.F > 0.95,

efficiency ≥ 100 lm/w & driver efficiency > 85%. For 24 W fixture wide voltage

range from 180 V to 270 V, 50/60 HZ @ 240V, 4 KV surge protection. The fixure

must have min. 2400 lumen light output. The fixture should be provided with

external separate Potted driver, latest Valid BIS approved Luminaire and driver.

The Fixture efficiency ≥ 90 lumens/watt only for safety and performance. (L70 @

50,000 Hrs.) The fixture should be able to easily mount on POP / Grid false ceiling.

The Luminiare should be tested as per IP 20 and following test reports should be

submitted at the time of approval: heat resistant test, thermal test, Ingress protection

test, IK test, Photobiological report with 3 core X 1.0 Sq.mm. flexible wire as per site

requirement [Note:-The manufacturer / authorized Channel partner of the

manufacturer has to submit 5 yrs. free replacement Guarantee for complete Fixture

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

187 SITC of Indoor Commercial Recess/Surface mounted (IP20) Max. 45w Cool White 20.00 Each 2071.00 RS: Two

Color LED office Lighting Luminaire having size (2'X2')/(4'X1') with suitable Thousand Seventy

seperate metal frame with white powder coating for installing fitting in gypsum One only

false ceiling with extrernal separate driver having BIS certification for installation in

Gypsum ceiling with single piece pressure die cast aluminium alloy housing/CRCA

sheet of 0.6 mm thickness with corrosion resistant powder coated finish

Polycarbonate diffuser with high brightness LED complete (only from Philips

Lumileds, CREE, Nichia, Buildglux, seoul & Osram CRI > 80, CCT 5600K (Bin 5600-

600k). The led's should be mounted on Metal core based PCB for better heat

conduction and long life of LED. (LM 79 for complete fixture, LM80 for individual

LED, report must be submitted) The Fixture should have protection of driver like

over/under voltage, THD<10%,Fixure must have Min 4950 Lumen light output.

Fixture Efficacy should be>=110 Lumens/watt. The fixture should be provided with

external separate driver BIS approved only for safety and performance. (L70 @

30,000 Hrs.) The Luminiare should be tested as per IP 20 and necessary test reports

should be submitted at the time of approval. ( [Note:- The manufacturer/authorized

Channel partner/dealer of the manufacturer has to submit 4 yrs. free replcement

Guarantee for complete Fixture

188 Supplying and erecting 8 W LED lamps with following wattage capacity of 220 to 49.00 Each 111.00 RS: One

240 voltage, minimum 15000 burning hours life, 500 V in built-surge Hundred Eleven

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp only

holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

189 Providing and erecting Polycarbonate body surface mounting LED Bulk head type 9 7.00 Each 780.00 RS: Seven

watt Lighting Fitting with electronic driver having THD < 15%, CRI>80, P.F.0.95 Hundred Eighty

And lumen output from luminaire 720 lm, input voltage range 90-300 V AC, 50 Hz only

cool white (3000 to 6500 k), inbuilt driver having efficiency >=80lm/w, -20 deg C to

+ 60 deg C working temperature, AL frame with Beam Angle 120 deg.

190 Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star 52.00 Each 2603.00 RS: Two

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite magnet Thousand Six

Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies, Hundred Three

shackle kit with earthing provision, copper winding, Power factor not < 0.9, Service only

Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM,230v

(tolerance as per IS : 374-2019), THD < 10%, compitible with electronic regulator

unit for Speed Control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and

rectifier circuit with surge, over current and overload protection , 50 Hz, Single

phase AC Supply, earthing etc. Complete as required. [Make shall be approved by

Engineer in Charge] (A) 1200 mm Sweep (48")

191 Supplying and erecting approved make Cabin fan of 230V. A.C. 50 Hz. 400 mm. 16.00 Each 1527.00 RS: One

sweep oscillating type complete erected with lead wires as directed. Thousand Five

Hundred Twenty

Seven only

192 Supplying & erecting approved make low noise Decorative exhaust fan having size 11.00 Each 1687.00 RS: One

150mm/ 200 mm with 1350 RPM with round / square frame ABS/metalic body Thousand Six

with Grill / inbuilt lowers. Hundred Eighty

Seven only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

193 Supplying and erecting approved make oscillating type bracket fan A.C. 230 V. 50 8.00 Each 2509.00 RS: Two

cy/s 400/450 mm sweep wall mounted with height adjustment and rotary tilting Thousand Five

device complete with guard, flexible Core plug top complete erected with lead Hundred Nine

wires as directed. (make & model approved by EIC as per specification) Cat II only

194 Supplying & Erecting Fan Hook Of 10 mm M.S Round bar bounded to the RCC bars 56.00 Each 125.00 RS: One

up to 50 mm Length each side & piereced through 18 Gauge G.I Box having 125 mm Hundred Twenty

dia depth of 75 mm complete erected concealed in ceiling with necessary modular Five only

plate / sheet.

195 Supplying & erecting 19/20 mm. nominal bore "B" class G.I. pipe / M.S. pipe down 55.00 Rn.Mtr 107.00 RS: One

rod erected duly painted for fan complete with necessary 24/0.2 flat 3 core flexible . Hundred Seven

Core with earthing. [The down rod thikness, hole, locking arrangement, only

construction, poweder coating, colour shed should be same as original down rod

brought with ceiling fan. For that agency has to give original down rod sample to

fabricator and one sample down rod should be approved with EIC. After approval

given by EIC, agency can use the down rod as per approved sample. If without

approval down rod will be erected on site, agency has to replace them with own

196 Supplying & Erecting Decorative Ding Dong bell Stereo type 250 Volt complete 2.00 Each 170.00 RS: One

erected on existing polished wooden block or in M.S. box with 3mm thick white ISI Hundred Seventy

mark laminated sheet. [Anchor (Chime model), vision, rider Make] only

197 Providing & erecting 240 V MCB Double pole switch for M & I load (C curve) 14.00 Each 360.00 RS: Three

having 10 KA breaking capacity & confirms to IS:8828 in Existing M.S. box having Hundred Sixty

following capacity. For 40 Amp. Cat III only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

198 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 9.00 Each 803.00 RS: Eight

having 10KA breaking capacity & confirms to IS :8828 in existing box having Hundred Three

following capacity [c] 63 Amp. Cat III only

199 Supplying & fixing box for housing RCCB + MCB combination made of 18 SWG 9.00 Each 493.00 RS: Four

sheet steel duly powder coated with gasket, dust & vermin proof bakelite shield two Hundred Ninty

earthing terminals for following type of RCCB, RCCB + MCB with necessary Three only

numbering / marking with oil Paint by painter. [a] For 2 pole [ Same company

metal box used as MCB / ELCB used with earthing terminal with necessary

Numbering/ marking with oil paint by painter]

200 For 4 pole [ Same company metal box used as MCB / ELCB used with earthing 7.00 Each 890.00 RS: Eight

terminal with necessary Numbering/ marking with oil paint by painter] Hundred Ninty

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

201 Providing ad erecting approved make single phase Double Door metal clad D.B. as 8.00 Each 6254.00 RS: Six

per relevant indian standards ammended upto date. Thousand Two

Supplying and fixing following way single phase MCB distrubution board of Hundred Fifty Four

company fabricated MCBDB Door Back Side &body Must Be Made OF 1.2 MM only

Thick CRCA Sheet sheet with sheet box with powder coated inside and outside

after apply seven tank chemical process of cover complete with suitable integral

single piece construction tinned copper busbar and link with all necessary

interconnection and with necessary size MS frame for mounting MCBDB.

Manufacturer must be provided (1) IP 43 and as per IS:8623-1 & 3, IEC 61439-1 &

having D type PU gasket. (2) Seven tank Powder coating Certificate (3) Tinned

Copper/Brass make neutral & Earthing link with isolation & Protecting Cover for

240 Volts on surface / recess complete with loose wire box, terminal connectors for

all incoming and outgoing circuits, with suitable size FRLSH PVC insulated copper

conductor up to terminal blocks and internal connection, tinned coppper bus bar,

no. tinned copper neutral link, tinned copper earth bar, din bar, detachable gland

plate, interconnections, powder painted including earthing etc. Single phase

incoming and horizontal single phase outgoing.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

For 16 Way MCBDB: Including 40 Amp. 30 mA double pole ELCB (ELCB

confirming to IS:12640/1988 having sensitivity of 30 mA and breaking capacity of

10 KA), MCB 40 Amp. double pole switch (C curve confirms to IS:8828 having

breaking capacity of 10 KA) and S.P. MCB of rating 6 to 32 Amp. with NL suitable

to operate on 240 Volt A.C. power. (6 Amp to 25 Amp:- 12 Nos. as per Site

Requirement, as per Instruction of EIC.) (The DBs should be used of same

company of MCB / ELCB to be used) (MCBDB must be erected in line & level with

spirit level and finish the external edge with box cutting plaster) (Same colour

MCB(SP/DP) should be used as same as MCBDB) [Including Necessary numbering

/ marking on box done with red colour radium sticker as per site requirement and

instructions given by EIC on site. Font / number size given by EIC on site as per

requirement]

202 Supplying & erecting 12 mm thick backelite sheet of approved make and grade on 3.00 Sq. 2289.00 RS: Two

existing 25 x 25 x 3 mm red oxide painted angle iron frame suitable for fixing ICDP Mtr. Thousand Two

SWITCH and energy meter (contractor shall make approved drawing of Bakelite Hundred Eighty

sheet To arrange required No. of Energy meter & ICDP/MCB switch-busbar etc. as Nine only

per Actual space available in electrical room at site)

203 Providing and erecting Approved make Four pole moulded case circuit breaker 1.00 Each 16061.00 RS: Sixteen

having breaking capacity ICU of 35 K.A. at 415 V having normal current rating 200 Thousand Sixty

A. with variable/Fixed thermal & magnetic release suitable to work on A.C.supply One only

50 c/s. with all internal connections, spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only. (Provision in Estimate)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

204 Providing, erecting, Fabricating the M.S. structure as per requirement of site as per 240.00 Kg 75.02 RS: Seventy

structure design Including proper size approved by EIC of M.S. angles, flats, bars, Five and Paise

square pipe, channels, sections (Tata, Jindal, Asian, JSI Make) complete with cutting, Two only

welding, grinding and finishing duly painted with Asian/Nerolac make premium

quality oil paint and true care red oxide metal primer,asian paint make with

erection on site as per direction of engineer in charge with necessary grouting

cementing, plastering and finishing complete. All hole opening of square pipe end

must be closed with M.S plate welding. Payment will be done on KG as per Actual

205 Providing and erecting metalic danger notice board for MEDIUM VOLTAGE 3.00 Each 69.00 RS: Sixty

installation to be erected as per I.S. Nine only

206-a Supplying and laying UPVC cable trunking system comprising unplasticised 10.00 Mtr. 275.00 RS: Two

polyvinyl, chloride rigid material with ignition free & flame proof confirming BS Hundred Seventy

.All necessary accessories and measuring of following sizes. [1] 75 mm x 50 mm Five only

trunking.[MK, LEGRAND, OBBO make Only]

206-b 100 mm x 50 mm trunking .[MK, LEGRAND, OBBO make Only] 10.00 Mtr. 424.00 RS: Four

Hundred Twenty

Four only

207-a Providing and erecting following type of Modular Type Accessories mounted with 5.00 Each 159.00 RS: One

20 G company fabricated metalic box, single mounting base frame covered with Hundred Fifty

textured / metallic front plate, modules erected with necessary connection. As Nine only

desired by Engineer in charge. (a) RJ-11Telephone Socket CAT-III

207-b Modem Jack for Computer Open RJ-45 CAT-Iil 5.00 Each 159.00 RS: One

Hundred Fifty

Nine only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

208 Providing & erecting Switch board for Computer or electric apparatus consisting of 5.00 Each 1122.00 RS: One

following items in single board erected on Metal board with 3 mm thick PC Thousand One

(Polycarbonet) / Acrylic sheet erected as directed. 2 no. 6/16 Amp. universal Hundred Twenty

Socket, 2 nos. 16 Amp. indicator switch, 2 nos. 6 Amp. Switch & 2 nos. 6 Amp. 5 pin Two only

Plug. For Computer power Supply board. Cat.-III.

209 SITC of specified make Cat - 6 voice /data cable to be done in prelaid PVC pipe / 200.00 Mtr 47.00 RS: Forty

raceway , but without the cost of raceway or pipe ( the wire is to be drawn from Seven only

MFD/ JB to outlet point) (a) CAT -

Y Colour ( For Voice Cabling ) & X -Colour(For Computer Data Cable ) .(

Molex/R&M/Avaya/Systimax/Legrand make)

210 SITC of 24 x 10/100/1000BASE-T ports 1.00 Each 15247.00 RS: Fifteen

4 x Gigabit RJ45/SFP Combo ports Thousand Two

Advanced L2 switching and security features Hundred Forty

L2+ Static Routing Seven only

Optional “standard mode” or “surveillance mode” management user interface.

([HP, Cisco, Juniper & model approved by EIC)

211 SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded (HP, Cisco, 1.00 Each 4357.00 RS: Four

Juniper & model approved by EIC) Thousand Three

Hundred Fifty

Seven only

212 Supply and installation of 9U steel rack for installing 4 nos. Ethernate 1.00 Each 11441.25 RS: Eleven

switches/Hubs. The Rack should be fully enclosed steel housing fabricated with 14 Thousand Four

SWG sheet and powder coated with glass doors and having wire management Hundred Forty

systems. The rate includes the Exhaust Fan, 2 nos. 4 socket and 1 switch power strip One and Paise

and all the wiring in the rack. (Rittal, Valrack, APC, Legrand make Only.) Twenty Five only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

213 SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less [Make and 5.00 Each 155.00 RS: One

model approved by EIC as per specification] Hundred Fifty Five

214 SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U' Snag less. For 2 Mtr. 5.00 Each 199.00 RS: One

[Make and model approved by EIC as per specification] Hundred Ninty

Nine only

215 Termination and Testing of CAT 6 data socket I/o as per industries with ferruling 5.00 Each 67.80 RS: Sixty

for Pyrotech table,including cost of Site Visit for Work and Service up to defect Seven and Paise

laibility period. Eighty only

216 Termination and Testing of RJ 11 Telephone socket as per industries with ferruling 5.00 Each 42.38 RS: Forty

for Pyrotech table,including cost of Site Visit for Work and Service up to defect Two and Paise

laibility period. Thirty Eight only

217 Providing & erecting Tag Box for Telephone Lines suitable for 10 Pairs Krone type 1.00 Each 985.00 RS: Nine

complete with Krone & locking arrangements. Hundred Eighty

Five only

218 Providing & erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI 50.00 Mtr. 58.00 RS: Fifty

marked copper wires of following size to be erected as directed. 3 core x 1.5 sq.mm. Eight only

PVC insulated round copper wire ISI mark.

219 Providing and erecting XLPE (IS:7098) (I)-88 ISI armoured cable multistrand 1150.00 Mtr. 182.00 RS: One

Aluminium conductor for 1.1 KV. to be laid 90 cms. Under ground or to be laid on Hundred Eighty

wall with suitable G.I. heavy guage 1.0 mm thick cable clamp or in existing DWC Two only

pipe underground or road crossing or floor of following size of cables. [d] 4 core x

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

220 Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to 1150.00 Mtr. 117.00 RS: One

IS: 16205 (part 24) 2018)) with minimum load required of 450N capacity with anti Hundred

rodent and ultra violet material properties with necessary connecting accessories of Seventeen only

same material at required depth to be laid 90 cms. under ground for laying of cable

below ground / road surface for enclosing cable and back filling the same to make

ground as per original. (A) For Outer dia. 50 mm and Inner dia. 38 mm. ) (Test

Certificate to be Submitted)

221-a Providing & fixing double compressed heavy duty flange type brass cable gland 10.00 Each 48.00 RS: Forty

with rubber ring for P V C insulated armoured cable complete with outgoing tails, Eight only

insulating tape etc. For following size cables. For 2 to 4 core x 2.5/4.0/6.0 Sq. mm

(Sigma, MCI, Comet Make Only)

221-b For 4 core*16 Sq. mm (Sigma, MCI, Comet Make Only) 36.00 Each 57.00 RS: Fifty

Seven only

222 Providing & fixing Solderless crimping type Aluminium lugs conforming to IS 60.00 Each 15.00 RS: Fifteen

suitable for cable of following size evenly crimped with high pressure tool & only

connected to switchgear terminals with brass/cadmium plated nut bolts in an

approved manner.For 16/25 Sq.mm.

223 Providing & fixing Solderless crimping type Copper lugs conforming to IS suitable 100.00 Each 8.00 RS: Eight

for cable of following size evenly crimped with high pressure tool & connected to only

switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

224 Providing and laying Mains with ISI marked, 1.1 KV grade electrolyte multi 50.00 Mtr 70.00 RS: Seventy

stranded, annealed copper conductor with heat resistant PVC insulated conforms to only

IS:694, IEC - 227 erected in existing pipe of following size (Specifically for control

panel, relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.One wire 6.00 sq. mm

225 Providing and laying Mains with ISI marked, 1.1 KV grade electrolyte multi 40.00 Mtr 114.00 RS: One

stranded, annealed copper conductor with heat resistant PVC insulated conforms to Hundred Fourteen

IS:694, IEC - 227 erected in existing pipe of following size (Specifically for control only

panel, relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.One wire 10.00 sq. mm

226 Providing and laying Mains with ISI marked, 1.1 KV grade electrolyte multi 350.00 Mtr. 176.00 RS: One

stranded, annealed copper conductor with heat resistant PVC insulated conforms to Hundred Seventy

IS:694, IEC - 227 erected in existing pipe of following size (Specifically for control Six only

panel, relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.One wire 16.00 sq. mm

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

227 Supplying and erecting Servo Controlled Voltage Stabilizer (SCVS) as per following 1.00 Each 64803.00 RS: Sixty Four

requirement: (1) Input Voltage Range - Three Phase 340 To 480 Volt AC. (2) Out put Thousand Eight

Volatge - Three Phase 415 Volt AC (Line - Line) with Voltage Regulation of +/- 1%. Hundred Three

(3) Frequency range - 47 Hz To 63 Hz. (4) Efficiency - More or equal to 98%. (5) Type only

of Stabilizer - Suitable for Balance & Unbalance Load and Voltage including SPD (6)

Controlled Type - Digital Micro Controller Based Disply. (7) Rate Of Correction -

Upto 100 Volt / Sec (Line - Line) (8) Servo Motor Drive - AC Syncronous Stepper

Motor - As per KVA Capacityy, Out put volatge and Voltage regulation

requirement. (9) Nil Wave form Distortion and Effect of Load POwer. (10) Responce

Time - 10 milli second. (11) Protection requirements - Input low Cut off protection /

Input High Cut Off Protection / Output Low Cut Off protection / IOutput High (12)

Fault Annuciation Panel LED shows Input present, Input high Input low, Output

Normal, Output High, Outpur low, Overload. (13) Output On time delay -

seconds (14) Ambient Tempeature capacity - 0 - 45 RH upto 90 %. (15) Enclosure

Type - IP55 (16) Type of Cooling - Oil,Output:Bypass switch with changeover

switch, & 5 year free replacement guarantee on Stamp paper.

Loading and unloading of above item shall be done by hydra and skill work force

under supervision of electrical engineer and guidelines given by manufacturer to

avoid damage to the item. Picture of it to be submitted in running bill / final

bill.Size of door and Ele. room / Pump room shall be checked by agency's engineer

before giving order. If found any problem in size discuss with GSPHCL engineer for

rectification before giving order. 15 KVA ( (make - Fuji-Electric,Servomax,Krykard)

228 Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade 260.00 Mtr. 58.00 RS: Fifty

ISI marked copper wires of following size to be erected as directed.For 1.50 Sq.mm 3 Eight only

core round PVC sheathed. having insulation colour RED and BLACK for Fire Alarm

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

229 SITC of Photo Electric Smoke Sensor, Features includes Low profile - only 2" high 5.00 Nos 3900.00 RS: Three

including base, variable sensitivity from 0.7 to 4% obs/Ft Simple and reliable device Thousand Nine

addressing, Automatic compensation for sensor contamination, Built-in Fire test Hundred only

feature, Two built-in power/alarm LEDs, Programmable non-polling LEDs, Non-

directional smoke chamber, Vandal resistant security locking feature. [Bosch,

HOCHIKI, siemen, GST make only ] (complient With EN54 &approved By LPCB

230 SITC of Fixed Temperature/Rate of Rise sensor, Low profile-only 2.00" high, 2.00 Nos 3900.00 RS: Three

including base, simple and reliable device addressing method, Rate of rise Thousand Nine

temperature threshold = 15° F/Min, Adjustable threshold temperature = 135° - Hundred only

190°,[Bosch, HOCHIKI, siemen, GST make only ](complient With EN54 &approved

By LPCB &vds]

231 SITC of Analogue Addressable Manual Call Point with Integral Short Circuit 1.00 Each 6000.00 RS: Six

Isolator, Analogue Addressable Protocol having, Bi-coloured status LED (red for Thousand

alarm, amber for (short-circuit), Non-frangible element fitted as standard (conforms only

addressed,[Bosch, HOCHIKI, siemen, GST make only ](complient With EN54

&approved By LPCB &vds]

232 SITC of Intelligent loop powered wall sounder which provide a range of tones and 1.00 Each 7500.00 RS: Seven

volumes with a maximum output of up to 102dB(A) (±2dB(A)) with low current Thousand Five

(complient With EN54 &approved By LPCB &vds]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

233 SITC of Microprocessor based Net-workable Analogue Addressable Fire Alarm 1.00 Each 93005.00 RS: Ninty Three

Control Panel. The Panel shall be compliant with EN54-2, EN54-4 and approved by Thousand Five

approved By LPCB &vds . The Fire Alarm Control Panel shall have inbuilt one loop. only

The Panel must have large graphic display. The Panel must also have the capability

to take Addressable Intelligent Wired device Each loop shall have a capacity of

analogue Addressable devices and 127 Base sounders/Base Sounder Beacons. The

Panel shall have 240 V AC power supply along with automatic Battery Charger.

Non-Networkable

Approved by LPCB [Bosch, HOCHIKI, siemen, GST make only ] (complient With

EN54 &approved By LPCB &vds]

234 SITC of automatic type fire extinguishers mono ammonium phosphate powder 50% 1.00 Each 5240.00 RS: Five

confirms to IS:4308. Applicable fire classed A, B & C, UGTS pressure gauge. Empty Thousand Two

weight 2.64 Kg., full weight 7.64 Kg. Can height 375 mm, diameter 230±10 mm, Hundred Forty

sheet metal thickness: 2 mm, Body construction deep drawn with MIG welding only

technology. Brass forged sprinkler valves with nozzle is specially designed to give

more than 99% discharge. Together with oifice characteristic to cover adequately fire

risks with scattering cone of 40 to 45° angle. External pure polyester (UV resistant)

and internal Epoxy polyester powder coated. Heat sensitive glass bulb of 68 °C.

Area covered will be 2-2.5 m² and volume of coverage is 7 m³ (Make: MINIMAX,

KANEX, , CEASE FIRE)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

235 Providing and fixing of ABC Type Store Pressure Fire Extinguisher Having capacity 9.00 Each 1991.00 RS: One

6 kg Filled with Mono Ammonium Phosphate Powder 50% confirms to IS 4308, Thousand Nine

Stored Pressure Type, UGTS Pressure Gauge, Can Height 530 mm, Diameter 150 ± Hundred Ninty

10mm, Discharge Time 24 Sec, Controllable discharge mechanism, Jet Range 5 One only

Meters, Average Discharge is 92%, applicable on Class A,B & C and electrically

started Fire, Fire Rating 4A:144B, Can Construction : Deep drawn & CO2 Mig

welded, EPDM(Ethylene Propylene Diene Monomer) Rubber Hose with both end

Aluminum clamped, Internal Coating - Epoxy Powder coating, External Coating -

Pure Polyester Powder coating (UV Resistant),Brass forged CE Marked valves with

NRV & Auto Safety Release with safety Pin is of SS material, Made up from 1.6mm

thick sheet, Extinguishers confirmed to IS 15683:2018 and ISI marked. Referance

Weight:-Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, 1. Necessary certificate & and

guarantee must be attached, 2. OEM has to provide wall mounting heavy duty

bracket/clamp, screw, hardware for installation. 3.Following printed marking

Manufacturing Date and Expiry Date must be mention on Extinguisher 4. Refilling

period must be of 3 Years. Following Printed marking on equipment must be

required:- Model No, Capacity, Gross Weight, Content, Fire Rating, Batch No, Serial

no, Mfg Month, Refilling Due. [with necessary numbering / marking with oil paint

by painter as instructions given by G.S.P.H.C.L engineer] (Make: KANEX,

MINIMAX, CEASEFIRE)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

236 Providing and fixing of CO2 type High Pressure Portable 4.5 kg Fire Extinguisher, 9.00 Each 6526.00 RS: Six

filled with Co2 Gas as per IS 15222, Control discharge mechanism fitted with 1 Thousand Five

Meter Wire Braided Hose & Electrical non-conductor Polyethylene Flat Horn with Hundred Twenty

Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 12 Sec, Average Six only

Discharge is 95%, Applicable on Class B, C and electrically started Fire, Fire Rating

55B, Internal coating is not applicable & External coating is of enamel spray

painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI Marked, CO2

Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body

confirms to IS 7285 and PESO ( Petroleum and Explosives Safety Organization)

APPROVED, Minimum Wall Thickness 4 to 4.2 mm, Extinguishers confirmed to IS

15683:2018 and ISI marked. Referance Weight:-Gross Weight 16.4, empty weight

11.9 Kg, 1. Necessary certificate & and guarantee must be attached, 2. OEM has to

provide wall mounting heavy duty bracket/clamp, screw, hardware for

installation. 3.Following printed marking Manufacturing Date and Expiry Date

must be mention on Extinguisher 4. Refilling period must be of 5 Years. Following

Printed marking on equipment must be required:- Model No, Capacity, Gross

Weight, Content, Fire Rating, Batch No, Serial no, Mfg Month, Refilling Due. [with

necessary numbering / marking with oil paint by painter as instructions given by

G.S.P.H.C.L engineer] (Make: KANEX, MINIMAX, CEASEFIRE)

237 Providing and erecting Inverter based approved make split air-conditioning unit 2.00 Each 52146.00 RS: Fifty Two

consisting of condensing unit with variable speed fan motor, inverter type Thousand One

hermetically sealed rotary compressor with accessories etc. duly connected Hundred Forty Six

separately erected evaporating unit and blower motor with its accessories by means only

of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost

includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS

Stand) with necessary core cutting.(2)For ISEER Range (KWH/KWH)(4.0 to 4.49) (B)

for 1.5 ton capacity

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

238 Executing All inclusive comprehensive maintenance (service + spare parts) cost for 2.00 Each 7540.00 RS: Seven

the period upto defect liability period for the Inverter Based Split type Air- Thousand Five

conditioning Unit of following Capacity (C) 1.7 to 2.0 ton capacity. Hundred Forty

(A) Breakdown Maintenance as per requirement and 2 dry services & 2 wet services only

(B) Routine Maintenance of Dry Services.

(C) Routine Maintenance of wet Services with water or Chemical as per site

requirement.

For 1st year agency has to provide 4 services as above and same for 2nd year and

Agency has to quote rate accordingly. Agency has to also provide the fitness

certificate from system agency and submit to G.S.P.H.C.L. Agency has to submit

FDR of approved bank as per clause 2.0, section 3, of Rs. 15080.00+GST or quoted

rate whichever is higher to G.S.P.H.C.L. for minimum maturity period of Four

years in favour of G.S.P.H.C.L., Which will be released after successful

completion of A.M.C. & at the completion of defect liability period

239 Supplying and erecting insulated pair of soft copper tubing including power and 30.00 Rmt 1147.00 RS: One

control cable, necessary PVC drain pipes for Split AC machine up to 4 TR capacity Thousand One

Hundred Forty

Seven only

240 Carry out RCC Core cutting- up to 100 mm dia./200mm thick Wall/beam/slab with 3.00 Each 1188.00 RS: One

providing PVC pipe of 3 mm thick inside and necessary finishing on both ends of Thousand One

wall . Hundred Eighty

Eight only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

241 Providing and erecting water cooler having storage capacity 80 Ltr. & cooling 3.00 Each 53976.00 RS: Fifty Three

capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water Thousand Nine

should drop by 15˚C within a hour, The water cooler should be comprising of Hundred Seventy

hermetically sealed compressor Reciprocating compressor with R134A gas , fan Six only

motor, Copper Condensing unit, fan motor, water tank surrounded by evaporating,

coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The

body of water cooler will be made from Stainless Steel, CP brass push cock, inlet

float valve, with all plumbing and electrical accessories, inlet, outlet, overflow and

PVC drain out connection to FD complete as required With 20 Amp. 3 pin plug Top

with indicator. (This item including comprehensive service & maintanance

including Spare Parts & consumable item during warranty period of one year.

Maintanance & service must be carried out by OEM dealer/distributer who has

executed the work. Service & Maintance must be as per OEM guid line.) (Agency

has to give AMC to water cooler OEM / authorized dealer upto defect liability

period] [Voltas, Bluestar, Usha model approved by EIC as per specification]

242 Supplying & erecting 5 stage single reverse osmosis water purification system with 3.00 Each 15466.00 RS: Fifteen

M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC Thousand Four

filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 psi Hundred Sixty Six

inline type post carbon filter auto low & high pressure switches with following size only

of storage tank & LPH capacity & erected as directed [B] 25 Ltr / Hr with 30 Ltr.

Storage Tank [ION EXCHANGE, AQUAGUARD, KENT, Eureka Forbes, Rain Drop,

or equivalent make approved by EIC as per specification]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

243 Executing comprehensive (All-in-All) service & maintenance with spare parts as per 3.00 Each 13919.00 RS: Thirteen

terms & condition of tender for R.O. System during defect liability period. For that Thousand Nine

main agency has to give All-in-All comprehensive maintenance contract to R.O. Hundred Ninteen

Plant OEM/Authorised dealer and copy of this contract will be submitted before only

final bill. Agency has to quote rate accordingly. Agency has to also provide the

fitness certificate from system agency and submit to G.S.P.H.C.L. Agency has to

compulsary submit FDR of approved bank as per clause 2.0, section 3, of Rs.

16425.00+GST or quoted rate whichever is higher to G.S.P.H.C.L. for minimum

maturity period of Four years in favour of GSPHC, Which will be released after

successful completion of A.M.C. & at the completion of defect liability period. R.O.

System agency has to maintain written record of service & maintenance during

defect liability daily period duly sign by police / Jail departmen and submitted

regularly to G.S.P.H.C.L. Agency has to give minimum four services per year of

entire R.O. Plant system during defect liability period and obtain necessary

certificate from police / Jail department and submitted to G.S.P.H.C.L. Agency has

to do maintenance as per terms & condition alternative in tender. Agency has to

replace Filter, Membrane, Pump etc. as per site required & working hours of R.O.

Plant. R.O. Plant OEM has to Provide fitness certificate at the time of releasing S.D.

For 25 Ltr. Capacity

(B) Total Amount of Electrical Work Rs.

(B) Total Amount of Electrical Work Rs.

TOTAL CIVIL + ELECTRICAL WORK Rs.

Executive Engineer

Signature of contractor Guj state police housing corporation limited