Construction of 1 No. Type IV Qtrs for Dr. Residence at Kandi in Tehsil Baroh Distt Kangra HP (SH- Construction of Civil work including water supply and Sanitary Installation and septic tank with soak pit etc)

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Sand filling under floor including watering, ramming, consolidating and dressing complete including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like floor etc.including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters)thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls(any thickness) partitions and the like including attached, pilasters, buttresses, plinth and string courses and the like including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (One cement; four sand; eight graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum comprassive strength of 20 N/mm square (Twenty Newton per square metre) with cement contents not less than 330 kg (Three hundred thirty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum compressive strength of 20N/mm square (Twenty Newton per square metre) with cement contents not less than 320 kg (Three hundred twenty kilograms) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum compressive strength of 20N/mm square with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts for all floors heights including entire carriage of materials within all leads, lifts and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 320 kg (Three hundred ten kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in walls/ vertical surface upto any thickness including attached, pilasters, buttresses, plinth and string courses and the like including entire carriage of materials within all leads, lifts and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete in reinforcement work for reinforced concrete Chhajjas for all thickness in all floor levels up to all heights including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work up to all floors level up to all height as per direction of Engineer-In-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying Damp Proof Course 100mm (One Hundred milimetres) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five milimetres nominal size) and curing complete, as required at site including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Applying a coat of hot bitumen mexphalt 80/100 (Eighty/Hundred) or equivalent using 1.70 Kgs. (one decimal seventy Kilogram’s) per square metre. On Damp Proof Course after cleaning the surface with a place of cloth lightly soaked in kerosene oil; including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing Tor steel reinforcement for reinforced cement concrete work including bending, binding, straightning and placing in position complete including cost of binding wires complete and other incidentals due for its completion for all floors including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : Six sand : Twelve graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) at plinth level in cement mortar 1:6 (One cement: Six sand) as per approved drawing, design and as directed by the Engineer-in-Charge including entire carriage of materials within all leads, lifts and other incidentals.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6(One cement: Six sand) including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4(One cement: Four sand) including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (One cement: four sand) including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (One cement: four sand) shall be proceded at the internal of 90-100 cm (Ninety to hundred centimetre horizontally as well as vertically to strength the masonry work including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 12mm (Twelve millimetre) thick preliminated board both side BWP Phenol bounded exterior/interior grade panelled shutters with frame of first class deodar wood for cup board i/c bright finished/black enamelled iron butt hinges with necessary screws 40mm (Forty millimetere) thick frame. complete as per direction of Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 40mm thick Second class deodar wood wire gauge shutters using galvanised M.S. wire gauge of IS gauge designation 85G with wire of dia 0.56mm for doors, windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 19mm (Nineteen milimetres) thick water proof termite resistant commercial board shutter of Century Ply ISI Marked or its equivalent with approved shade shall be finished with green spectrum veneer of Greenlum/Mayur of approved shade with 6mm/12mm (Six millimetres/Twelve millimetres) thick hard wood edging and all cut portions round and backing for cup board/SDB including fixing with nickel plated piano hinges with screws etc complete shutter from outside shall be finished with 1mm (One millimetres) thick laminated of approved shade in matt finished & painted from inside as per direction of Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 19mm (Nineteen millimetres) thick water proof terminate resistant commercial board ply Centuary/ Alpro or equivalant in shelves/box for cup-board including its selves and shutter, back sides of the cup board with butt joints and fixing with nails & screws and all cut portion of selves and box shall be finished with 6mm (Six millimetres) hard wood edging complete as per direction of Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 6mm (Six millimetres) thick ply wood lining Centuary with butt jointing (frame work and cover fillets to be measured and paid for separately) complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 8mm (Eight millimetres) thick ply Centuary/ Alpro or equivalant in shelves/box for cup-board with butt joints and fixing with nails and screws etc commertial board box including selves and shutter both sides of the cup board shall be of 8mm (Eight millimetres) thick ply all cut portion of selves shall be finished with 6mm/12mm (Six millimetres) / (Twelve millimetres) hard wood. The shutter from outside shall be finished with 1 mm (One millimetre) thick lamination of approved shade in mat finished and painted from inside complete as per direction of Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 12mm (Twelve millimetres) thick and 100mm (One hundered millimetres) wide palmet with 25mm (Twenty five millimetres) dia wooden curtain rod with and brackets including fixing with 25x3mm (Twenty five into three millimetres) M.S flat 10 cm (Ten centimetres)long and plug etc,complete in first class deodar wood. complete as per direction of Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (Twenty five into Twenty five into Five milimetres) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25mm (Twenty five into Twenty five milimetres) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two decimal Five milimetres) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing MS plain grills of required pattern in steel frames of windows and ventilators etc with M. S flat 20x5mm (Twenty into five millimetres) and 8x8mm (Eight into eight millimetres) solid square or round bars with round headed bolts and nuts etc. or by screws complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 250x16mm (Three hundred into Sixteen milimetres) size aluminum oxidized PILOT/ Sheel or equivalant sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

300x16 mm (Three hundered into Sixteen )

250x16mm (Two hundred fifty into Sixteen milimetres) size

Providing and fixing aluminum oxidized PILOT/ Sheel or equivalant Tower bolts (Barrel type) anodized transparent or dyed to required colour and shade with necessary screws etc; complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

250x10mm (Two hundred into Ten milimetres) size

150x10mm (One hundred fifty into Ten milimetres) size

Providing and fixing aluminum oxidized PILOT/ Sheel or equivalant handles anodized transparent or dyed to required colour and shade with necessary screws etc; including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

125x10mm (One hundred into ten milimetres) size

100x10mm (One hundred into ten milimetres) size

Providing and fixing 150mm (One hundred fifty millimetres) M.S. double acting spring hinges of approved brand with necessary screws etc. complete as per the direction of Engineer-In-Charge including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 65x35mm (Sixty five into Thirty five milimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete (Indian make of approved quality) complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing catcher for cup board shutters with necessary screws etcetra; complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing oxidized 200mm (Two hundred milimetres) size oxidized PILOT/ Sheel or equivalant oxidized M.S. hooks and eyes complete with necessary screws etc; complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing land fixing Precast terrazzo tiles ISI market No. IS-1237 hydraulic compressed 20mm (Twenty millimetres) thick with marble chips of specified sizes laid in floors, treads of steps and landings on a bed of 25mm (Twenty five millimetres) averatge thickness of cement mortar 1:6(One cement: Six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of Grey shade upto all floors level complete including entire carriage of materials within all leads, lifts and other incidentals and as per directed by the Engineer-in-Charge.

Providing and laying 600x600mm (Six hundred into six hundred milimetres) matt finish vitrified tiles of itco/Rak/Kajaria/Orient and bell in grey/coloured of approved shade in flooring, treads of steps and landing laid on a bed of 12mm (Twelve milimetres) thick cement mortar 1:3 (1 cement: 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete upto all floor level including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying ceramic tiles antiskid of Orient/Somany/Rak or its equivalent as per approved shade 5.5 mm (Five point five millimetres) thick in flooring 300x300mm (Three hundred into Three hundred milimetres) size in treads of steps laid on a bed of 12mm (Twelve milimetres) thick cement mortar 1:3 (One cement : three sand) finished with cement slurry mixed with pigment to match the shade of tiles upto all floor level including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing land fixing Precast terrazzo tiles ISI market No. IS-1237 hydraulic compressed 20 mm (Twenty millimetres) with marble chips of specified sizes in skirting and risers of steps not exceeding 30cm in height on 10mm (Ten millimetres) thickness of cement mortar 1:3 (One cement : Three Sand) jointed with neat cement slurry and pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of following shades GREY (Wherever required) including rubbing and polishing upto all floors level complete including entire carriage of materials within all leads, lifts and other incidentals and as per directed by the Engineer-in-Charge.

Providing and laying 300x300/200x300 mm (Three hundred into three hundred/Two hundred into Three hundred milimetres) size of Nitco/Kajaria/Orient/Bell/Swastik/Rak or equivalent white glazed tiles 6mm (Six milimetres ) thick in skirting, risers of steps and dado laid on a bed of 12 mm (Twelve millimetres) thick cement mortar 1:3 (One cement : Three sand) finished jointed with cement slurry complete upto all floors level including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying 20mm (Twenty milimetres) thick White Makrana Marble work (table rubbed and polished) in flooring 20mm (Twenty milimetres) thick base in cement mortar 1:3 (One cement: Three sand) including pointing with cement mortar 1:2 (One White cement: Two marble dust) with an admixture of pigment to match the marble shade complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing 50mm (Fifty milimetres) thick cement concrete flooring thick cement concrete 1:2:4 (One cement : Two sand: Four graded crushed stone aggregate 20mm (twenty milimetres) nominal size laid in one layer finished with a floating coat of neat cement complete upto all floor level, including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted sheet Tata/Shakti or equivalent in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 10 (Ten) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required including carriage of materials within all leads and lifts and other incidentals as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge

Providing and fixing Tata/Shakti or equivalent valleys 90 cm (Ninety centimetres) over all over all with 0.60mm (Zero decimal Sixty milimetres) thick prepainted sheet roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester organic coating of 20 (Twenty)microns primer coating back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.63mm (Zero decimal Sixty three milimetres) thick prepainted steel sheet ridges (Factory made) shall be having proper Gola/Shape of steel sheet Tata/ Sakti or equivalent with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating plus back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with plain galvanized iron J or L hooks, bolts and nuts 8mm (Eight milimetres) diametres with G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 30cm (Thirty centimeters) wide 30cm deep minimum (Thirty centimeters) over all semi-circular 0.60mm (Zero decimal sixty milimetres) thick plain G.I. sheet gutter Tata/Shakti or equivalent with iron brackets 40x3mm (Forty into Three milimetres) size bolts and nuts and washers etcetera including making necessary connections with rain water pipe complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing plain B.P. iron sheet 1.66mm to 2mm (One decimal sixty six millimeter to Two milimetres) thick 16 gauge fixed in soffits /ceiling including jointing with gas/electric welding in position complete (frame work is to be measured and laid for separately including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (Sixteen into Three point one five milimeters) lugs 10 cm (Ten centimeter) long embedded in cement concrete blocks 15 x10x10 cm (Fifteen into ten into ten centimeters) size of 1:3:6(1 cement:3 sand:6 graded stone aggregate 20mm wenty milimeters) nominal size) or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Fixed steel window

Top hung window

Providing and fixing factory made double steel shutter window side hung( glazed and other wire gauge) of standard rolled steel section jointing metered welded with manufactured to relevant ISI standard specification with 16x3.15 mm lugs 20 cm long embedded in cement concrete block 1:3:6 (1 Cement :3 sand : 6 graded crushed stone aggregate 20mm nominal size) with wood/steel plugs and screws or rawl/plugs screws or with fixing clips or with bolts and nuts as required and iron fitting including providing and fixing glass pans with special putty of glazed side of shutter and wire guage of IS designation 85G with metal beading another side complete including priming coat of red lead paint complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimetres) diametres on wall face rain water pipes of 4.5 kgs/sqm (Four point five kilograms per square metre) working pressure class B PVC D-Plast ISI mark of SFMC/Finolex/Relpipe(Reliance) or its equivalent hight denesity pipe for rain water pipe fixed with approved adhesive including filling the joints complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing on wall face P.V.C. acessories for rain water pipes 4/6 kgs/sqm (Four/Six kilograms per square metre) working pressure class B PVC D-Plast ISI mark of SFMC/Finolex/Relpipe(Reliance) or its equivalent high denesity pipe for rain water pipe fixed with approved adhesive including filling the joints complete wincluding entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

100mm (One hundred millimetres) dia PVC Plain bend

100mm (One hundred millimetres) dia PVC Shoe

Providing and fixing M.S. holder bat clamps of approved design to PVC. rain water pipe embedded in and including cement concrete blocks 10x10x10cm (Ten into ten into ten centimetres) of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etcetera including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing angle iron doors frames (Single rebate) manufactured from M.S. angle section of 40 40 X 5 (Forty into forty into five milimetres) mm and M.S, flat 50x5 (Fifty into five milimetres) as per design and drawing including jambs, lock jambs beeds if required angles threshold of M.S. angle 50x25mm(Fifty into twenty five milimetres) welded or rigidly fixed by mechanical means lugs with split ends tails to each jambs including steel butt hinges 2.5mm(Two decimal five milimetres) thick with a provision of locking arrangements and shock absorbers as specified and applying coat of approved steel primer after pre-treatment of the surfaces or as directed by the Engineer-in-Charge within all leads , lifts of materials and other incidentals.

Providing and fixing angle iron doors frames (Double rebate) manufactured from M.S. angle section of 40x40x5mm(Forty into Forty into Five milimetres) and M.S, flat 50x5 (Fifty into five milimetres) as per design and drawing including jambs, lock jambs beeds if required angles threshold of M.S. angle 50x25mm(Fifty into twenty five milimetres) welded or rigidly fixed by mechanical means lugs with split ends tails to each jambs including steel butt hinges 2.5mm(Two decimal five milimetres) thick with a provision of locking arrangements and shock absorbers as specified and applying coat of approved steel primer after pre-treatment of the surfaces within all leads , lifts of materials and other incidentals

Providing and fixing M.S. xchannel in doors and windows frames manufactured from M.S. Channel section of 75.18x38.1 mm(Seventy five point eighteen intothirty one point five milimetres) and M.S, flat 75x5 (Seventy five into five milimetres) combination as per design and drawing including butt hinges, jambs, lugs with split and tails to each jamb including butt hinges 2.5mm(Two decimal five milimetres) thick with a provision of locking arrangements and shock absorbers as specified and applying coat of approved steel primer after pre-treatment of the surfaces within all leads , lifts of materials and other incidentals

Steel work welded in built up sections joints channels, angles, tees frame work for ceiling/false ceiling flats with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint i/c framed work with angle tees 40x6mm including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Steel work welded in built up sections trusses and framed work, including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint in gratings framed gaurds, bars, ladders, railing, brackets and similar work, including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing M.S. fan clamps of Type-I of 16 mm (Sixteen milimetres) diameters M.S. barbent to shape with hooked ends to Reinforced Cement Concrete slab during laying including painting the exposed portion of loop all as per standard design complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Applying priming coat over new steel and other metal surfaces with Nerolac/ Asian or equivilant after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Painting two or more coats (excluding priming coat) with Nerolac/ Asian or equivilant on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter white ready mixed paint white including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces with Nerolac/ Asian or equivilant after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting ready mixed paint brushin wood primer pink including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Painting two or more coats (excluding priming coat) on over new wood and wood based surfaces with Nerolac/ Asian or equivilant with enamel paint other than white brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

15mm (Fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) upto floor all level including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) above plinth level floor all level including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

15mm (Fifteen milimetres) thick cement plasters in two coats bearing coat 10mm (Ten milimeters) and finishing coat 5mm (Five milimeters) on fair side of brick/concrete/stone walls for interior plastering upto any height including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:4 (One cement : Four sand) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Distempering (two or more coats) with oil bound washable distemper with Nerolac/ Asian or equivalant of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.priming coat with distemper primer including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima ) or equavalent Asian paints of Nerolac on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (Seventy five milimetres) thick(un-consolidated)bed of dry brick/stone aggregate 40mm (Forty milimertres) nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) including finishing the top surfaces of concrete smooth including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cm (Fifteen into twenty three centimetres) in cement mortar 1:6 (One cement : Six sand) and inside plastering with cement plaster 1:3 (One cement : Three sand) including earth work and laying 10cm cement concreter in 1:5:10 (One cement: Five sand: Ten graded) crushed stone aggregate 40mm (Forty millimetres) nominal size and 7.5 cm (Seven point five centimetres) cement concrete 1:2:4 (One cement: Two sand: Four graded) crushed stone aggregate 20mm (Twenty millimetres) nominal size and finished with a floating cost of neat cement complete as per standard design complete in all respect including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing railing (Balcony railing) composed of moulded hand rail of M.s. hollow pipe size 80x40x3.2mm (Eighty into Forty into Three point two millimetres) and 25mm (Twenty five millimetres) solid square bar to support the hand rail complete as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing polythelene aluminum polythelene (P.E.) A.L P.E composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 flow guard/Kitec/Kisan or its equivalent for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work) pipes exposed on wall 1216, including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals.

1216 (16mm (Sixteen milimetres) O.D. pipe

2025 (25mm (Twenty five milimetres) O.D. pipe

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor complete in all respect including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

20mm (Twenty milimetres) nominal bore/diameters

25mm (Twenty five milimetres) nominal bore/diameters

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) 40mm dia including all tube fitting such as nipples, elbows, unions, tees and clamps including making good the wall, ceiling and floor complete in all respect including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PVC bat clamp including steel bolts to sand cast/spun iron pipes embedded and including cement concrete block 10x10x10cm (Tem into ten into ten centimetres) of 1:2:4 (1cement: 2sand: 4 graded crushed stone aggregate 20mm nominal size and cost of cutting holes and making good the walls etc. including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150 mm (One hundred fifty milimetres) nominal size

100 mm (One hundred milimetres) nominal size

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals.

Providing and fixing P.V.C. ISI mark SFMC/Finolex/Relpipe (Reliance) or equivalent pipe fittings and accessories single for sewerage pipe confirm to IS No. 14735-99 plain bend complete including fixing with approved adhesive including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150mm (One hundred fifty milimetres) diametres

110mm (One hundred one milimetres) diametres

Providing and fixing P.V.C. tees medium class D-Plast or equivalent complete including fixing with approved adhesive including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 150mm (One hundred fifty milimetres) diametres PVC Tee (150 mm)

Providing and fixing 110mm (One hundred ten milimetres) diametres PVC Tee (100 mm)

Providing and fixing P.V.C. D-Plast or equivalent heal rest including filling the joints with including fixing with approved adhesive including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150mm (One hundred fifty milimetres) diametres

110mm (One hundred ten milimetres) diametres

Providing and fixing P.V.C. D-Plast or equivalent Collar including filling the joints with including fixing with approved adhesive including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150mm (One hundred fifty milimetres) diametres

110mm (One hundred ten milimetres) diametres

Providing and fixing P.V.C. D-Plast or equivalent Cowl including filling the joints with including fixing with approved adhesive including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150mm (One hundred fifty milimetres) diametres

110mm (One hundred ten milimetres) diametres

Providing and fixing 110 mm X 90 mm (One hundred ten into ninety millimetres) nominal diameter PVC floor trap including filling the joints with adhesive mixure complete, including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing in trenches in PVC pipe class "A" soil waste and ventilating pipe fixing with adhesive mixture complete of supreme or its equavalents make including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

150mm (One hundred fifty milimetres) nominal size

110mm (One hundred ten milimetres) nominal size

Providing and fixing vitreous china Cera / Hindware/Jaquar of star white/ snow white shade or equivalent ISI marked big size No 20090 vitreous china water closet squatting pan (Orissa Type) WC pan size 53x41cm (Fifty three into forty one centimetres) orissa pattren (earth work, bed concrete, foot rest and trap to be measured and paid for separately) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing vitreous china wash down water closet Cera Anglo Indian W.C. (universal) No. 2061 (Europeon type W.C. pan) or its equivalent with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres apacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovrflow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately . complete including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimetres) PVC P or S traps for water closet (squatting pan) Cera/Jaquar or its equivalent including jointing the trap with pan and soil pipe in cement mortar 1:1 (One cement : One sand) sand cost iron including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing vitreous china padestal for wash basin complete recessed at the back for the reception of pipes and fittings including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 610x510x200mm (Six hundred ten into five hundred ten into two hundred milimetre) Size will bowl depth 200mm (Two hundred millimeters) stainless steel Kitchen sink Cera/Hindware/Jaquar or its equivalent of approved standard ISI marked with drain board super deluxe 6321 with with C.I or M.S bracket painted white including cutting holes in walls and making good the same but including fitting including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 550x400 mm (Rupees five hundred fifty into Four hundred millimeters) Cera/Hindware or its equivalent vitreous china wash basin with single hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 32 mm (Thirty two milimeters) diameter rubber plug for sink or wash basin (Heavy duty make ISI marked No-8931 & 7893) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 32mm (Thirty two milimetres) nominal bore G.I./M.I Union of following sizes (where required) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 32mm (Thirty two millimetres) diametres P.V.C. Cera / Hindware/Jaquar or equivalent waste pipe for wash basin or sink complete, including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 32mm (Thirty two millimetres) diametres CP ISI marked or equivalent waste (Heavy duty makes ISI marked No. 8931 & 8934) including brass check nut complete, including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty milimetres) beveled edge mirror or superior glass mounted on 6mm (Six milimetres) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass and screws and washers including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 600x20mm (Six hundred into Twenty milimetres) C.P. Clarion series (GA/GB Endorsing the green building norm/Green Initiative/Jaguar or equivalent brass Towel rail complete with C.P. brass brackets fixed to wooden plug with C.P. brass screws including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 600x120mm (Six hundred into One hundred twenty milimetres) glass shelf with C.P. brass Jal/Jaquar or equivalent (Heavy duty makes ISI marked is No. 8931 & 8934) brackets and guard rail complete fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing C.P. brass toilet paper holder Clarion series (GA/GB Endorsing the green building norm/Green Initiative/Jaguar or equivalent (Heavy duty make ISI marked No-8931 & 8934) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 15mm (Fifteen milimetres) diametres C.P. brass pillar tap with capstan bead Jal/Jaquar or equivalent including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 15mm (Fifteen millimetres) nominal bore chromium plated brass ISI marked No. 8934) bib tap E 58 (Eighty eight)Jal/ESS ESS or equivalent, including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 15mm (Fifteen millimetres) nominal bore Jal/ESS ESS or equivalent chromium plated ptmt push cock tap Jal/Jaguar or equivalent, including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 15mm (Fifteen milimetres) diametres brass angle valve of approved make & design without nuts Jal/Jaquar or equivalent including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing brass full way valve with wheel Jaquar or its equivalent including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

15mm (Fifteen milimetres) nominal bore

20mm (Twenty milimetres) nominal bore

Providing and fixing 15mm (Fifteen milimetres) nominal bore brass valve Jal/ESS ESS or equivalent (Horizontal plunger type) high pressure with copper plate complete within all leads, lifts of materials and other incidentals

Providing and fixing 15mm (Fifteen milimetres) nominal bore PVC connection pipe with brass union 45cm (Forty five Centimetres) length including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and placing water tank make P.V.C. SINTEX or equivalent having capacity of 500 (Five hundred) liters each tank necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let and inside painting ball valve with cover and locking arrangements including painting of good quality complete in all respect including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying 150 mm (One hundred fifty millimetres) nominal bore/diametres to level or slopes PVC pipe for sewerage line including joint with approved adhesive mixture, within all leads, lifts of materials and other incidentals

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (Twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 1.00 mtrs(One metre) deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Construction brick masonry chamber for under ground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (One : Five) C. I. cover with frame (light duty) 455x610mm (Four hundred fifty five and Six hundred ten millimeteres) internal dimensions total weight cover with frame to be not less than 38kg weight of cover 23kgs and weight of frame 15kgs RCC top slab 1:2:4 (1cement:2sand: 4graded crushed stone aggregate 20mm foundation concrete 1:5:10 (1cement:5sand:10 graded crushed/broken stone aggregate 40mm nominal size inside plastering 15mm thick with cement mortar 1:3 (1cement:3 sand) finished with a coat of neat cement on walls and bed concrete etcetera complete inside dimensions 455x610mm (Four hundred fifty five into six hundred ten milimeters) and 450mm (Four hundred fifty milimeters) deep single pipe line complete in all respect including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying 100mm (One hundred milimetres) dia cement concrete 1:5:10 (One Cement: five Sand : ten graded stone aggregate 40mm (Forty milimetres) nominal size) bedding for PVC soil waste pipe of the following internal diameters, necessary form work and curing complete in all respect including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing white plastic seat (solid) hollow type and cover for wash down water closet with C.P. brass hinges and rubber buffers matching with shade of European W.C. panm including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing chromium plated (Heavy duty makes ISI marked No. 8931 & 8934) brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 200 mm (Two hundred millimetres) wide sand cast iron hinges with chequered or ribited non slip surface including fixing in holes with 200x200x20mm (Two hundred into two hundred into twenty milimetres) in cement concrete 1:3:6 (One cement : Three sand: six graded crushed stone aggregate 20mm (twenty milimetres) nominal size complete, including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing in cast iron cover with frame for manhole 455mmx610mm (Four hundred fifty five into Six hundred ten millimetres) light duty weight not less than 50 Kgs (Fifty kilograms) complete including entire carriage of materials within all leads lifts and other incidentals, and per as directed by the Engineer-in-Charge.

Providing and fixing PVC pipe 100mm (One hundred millimetres) dia for inlet & outlet connection complete complete including entire carriage of materials within all leads lifts and other incidentals, and per as directed by the Engineer-in-Charge.

Alpna Sharma