Construction of Health Sub Centre building at Sathana in Tehsil Fatehpur distt. Kangra HP SH Construction of building portion including water Supply and sanitary Installation

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches drain etcetra in all heights/depth in all kinds of classification of soil such as pick work , jumper work ,pick jumper work , blasting work ( soft and hard rock ) saturated soil including chiseling or wedging out rock where blasting is prohibited or any other mixed variety of soil including shoring , strutting , dewatering and pumping or bailing out water ( surface and sub soil water ) upto any depth or any quantum of water including slush which may arise during dewatering removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads as directed by Engineer-in-Charge and then returning the stacked soil in 15cm ( fifteen centimetre) layers when required into plinths and sides of foundation etecetra , consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated earth as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials with in all leads and lifts. The rate is including Royality, malkana,octroi, toll tax, sale tax, G.S.T. and all other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per HPPWD specification or as directed by Engineer-in-Charge, including carriage of materials with in all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, sale tax, toll tax, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frames 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in foundation footings, basis of columns etcetera and mass concrete including carriage of materials within all leads and lifts and other incidental. The rate is including Royality charges, Malkhana, Octroi, sale tax, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in suspended floors, roofs, landings , balconies, shelves and access platform and the like floor etcetera upto any thickness upto all floor level including carriage of materials within all leads, lifts and other incidental. The rate is including Royality charges, Octroi, Malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters) thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in Columns, pillars, piers, abutments, posts and struts (square, rectangular or polygonal in plan) in any heights / thickness/depths etcetera upto all foor level including carriage of materials within all leads lifts and other incidental. The rate is including Royality charges, Octroi, Malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in stair cases with sloping or stepped soffits excluding landing upto all floor level including carriage of materials within all leads, lifts and other incidental. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frames 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in Lintels, beams, plinth beams, girders, bressumers and cantilevers upto any heights/depths / thickness upto all floor level including carriage of materials within all leads, lifts and other incidental. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering in all heights below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls upto any width etcetera upto all floor level including carriage of materials within all leads, lifts and other incidental. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and laying in position cement concrete 1:5:10 (one cement isto five sand isto ten graded broken /crushed stone aggregate 40mm(forty millimeters) nominal size) of specified grade vibrated and mechanically mixed and curing complete excluding the cost of centering and shuttering in all work upto plinth level including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and laying in position cement concrete 1:4:8 (one cement isto four sand isto eight graded broken /crushed stone aggregate 40mm(forty millimeters) nominal size) of specified grade vibrated and mechanically mixed and curing complete excluding the cost of centering and shuttering in all work upto plinth level including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete grade M-20 (twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( twenty newton per square millimetre) for reinforced cement concrete work with cement content not less than 330kg/cum ( three humndred thirty kilogram per cubic metre) as per approved design mix for all works up to plinth level to give a smooth surface including curing complete and pumping of concrete to site of laying but excluding cost of centering, shuttering, finishing and reinforcement including admixture in recommended proportion as per IS: 9103 to accelerate, retard setting of concrete, improve work ability without impairing strength and durability including carriage of materials with in all leads, lifts and other incidentals. The rate is including royality charges, octroi, sale tax, malkana, G.S.T. and other taxes as imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25( M-twenty five) for reinforced concrete work using cement content not less than 360kg/ cum ( three hundred sixty kilogram /per cubic meter as per approved design mix for all work above plinth level up to floor all five level to give smooth surface including curing and pumping of concrete to site of laying but excluding cost of centring /shuttering, finishing and reinforcement including admixture in recommended proportion as per IS 9103 to accelerate,retard setting of concrete improve work ability without impairing strength and durability including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Steel reinforcement Thermo-Mechanically Treated bars of grade of Fe-500D or more of Tata Tiscon/sail for reinforced concrete work including straightening, cutting, bending, placing in position and binding including the cost of binding wire complete upto all floor level and carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate is including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Smooth finishing of the exposed surface of reinforcement cement concrete work with 6 mm (six milimeter) thick cement mortar 1:3 (one Cement : three fine sand).including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Brick work using Second class common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level upto all floor level in cement mortar 1:6 (one cement : six sand) and curing complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to all floor level.Cement mortar 1:3 (one cement : three coarse sand), as per approved drawing, design and specifications and as per direction of the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, GST, sale tax, malkana and all other taxes as imposed by the Government.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement isto six coarse sand isto twelve graded stone aggregate 20 mm( twenty millimeter) nominal size) upto plinth level with cement mortar 1:6 (one cement isto six coarse sand) including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Filling in plinth with stone under floors including watering ramming, consolidating and dressing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 18 mm (eighteen millimeter) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut granite of approver shade and colour for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimeter) thick base of cement mortar 1:4 (One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etectera complete at all levels as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing ISI marked 35mm(thirty five millimetre) thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ( three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws and carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and fixing 25 mm (twenty five millimeter) thick second class deodar wood panelled or panelled and glazed shutters for cup board including ISI marked anodised aluminium butt hinges with necessary screws etecetra complete including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design, specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and fixing cabinet work made of 19mm (Nineteen milimetre) thick water proof termie resistant commercial board box including vertical partitions shelves and shutters ,back side of the cup board/ cabinet shall be finished with 8mm( eight milimetre) thick ply. All cut portion of the shutters and shelves shall be finished with 6mm (Six milimetre) thick hard wood edging, the shutters from outside shall be finished with 1.00mm ( one millimetre ) thick lamination of approved shade including nikel plated bright finished piano hinges and carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and fixing 40mm ( forty millimetre) thick second class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screw including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and fixing 30 mm (thirty millimetre) thick second class deodar wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (zero point six three millimetre) for doors, windows and clerestory windows with hinges and necessary screws with ISI marked M.S. pressed butt hinges bright finished of required size including carriage of materials within all leads, lifts and other incidentals charges as per approved drawing ,design specification, and as directed by Engineer in charge. The rate including Royality charges, Octroi, sale tax, Malkhana, GST and all other taxes as imposed by the Government.

Providing and fixing 300x16mm (three hundred into sixteen millimeter) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 250x16mm (two hundred fifty into sixteen millimeter) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 250x10mm (two hundred fifty into ten millimeter) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 200x10mm (two hundred into ten millimeter) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 65mm (sixty five millimeter) special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimeter) oxidised M.S. double acting spring hinges with necessary screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 200mm (two hundred millimetre) weighing not less than 120 gms (one hundred twenty grams) oxidised M.S. casement stays (straight peg type) with necessary screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 250x20x6mm (two hundred fifty into twenty into six millimeter) ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 25mm (twenty five millimetre) diameter chromium plated brass curtain rod having wall thickness of 1.25mm (one point two five millimetre) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etcetera wherever necessary complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of windows etcetera with M.S. flats, square or round bars etcetera including welding to steel windows and priming coat with approved steel primer all complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Structural steel work of TATA TISCON/SAIL/JINDAL riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing factory made double shutter for steel windows side hung (one glazed and other wire gauged) of standard rolled steel section joints mitred and welded with 15x3mm (fifteen into three millimetre) lugs 10cm (ten centimetre) long embedded in cement concrete block 15x10x10cm ( fifteen into ten into ten centimetre) size of 1:3:6 (one cement isto three sand isto six graded stone aggregate 20mm (twenty millimetre) nominal size) or with wooden/steel plugs and screws or rawal plugs or with fixing clips or with bolts and nuts as required and iron fittings including providing and fixing of glass panes 4mm (four millimetre) thick with glazing clips and special metal sash putty of approved make for glazed shutter and metal beading with screws etecetra and including fixing of wire gauge using galvanised M.S. wire gauge of IS gauge designation 85-G (eighty five-G) with wire of diameter 0.56mm (zero point five six millimetre) and for fixing wire mesh with M.S. flat 20x3mm (twenty into three millimetre) for beading with screws and applying a priming coat of approved steel primer after pretreatment of the surface as directed by Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including Royality, malkana, octroi, toll tax, sale tax, G.S.T. and other taxes imposed by the Government. Side Hung Window Double shutter one glazed and other wire gauged.

Providing and fixing steel glazed doors, windows and ventilators of standerd rolled steel sections, joints mitred and welded with 15x3mm (fifteen into three millimeter) lugs 10cm (ten centimeter) long embedded in cement concrete block 15x10x10 cm (fifteen into ten into ten centimeter) size of 1:3:6 (one cement isto three sand isto six graded stone aggregate 20mm (twenty millimeter) nominal size) or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fitting such as handles, tower bolts etecetra including providing and fixing of glass panes 4mm (four millimetre) thick with gazing clips and special metal sash putty of approved make complete including applying a priming coat of red lead paint as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government. Fixed steel windows

Providing and fixing steel glazed doors, windows and ventilators of standerd rolled steel sections, joints mitred and welded with 15x3mm (fifteen into three millimeter) lugs 10cm (ten centimeter) long embedded in cement concrete block 15x10x10 cm (fifteen into ten into ten centimetre) size of 1:3:6 (one cement isto three sand isto six graded stone aggregate 20mm (twenty millimeter) nominal size) or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fitting such as handles, tower bolts etecetra including providing and fixing of glass panes 4mm (four millimetre) thick with gazing clips and special metal sash putty of approved make complete including applying a priming coat of red lead paint as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government. Top hung ventilators.

Providing and fixing double rebate angle iron frame for doors, windows and clerestory windows manufactured from steel iron section of 40x40x5mm (forty into forty into five millimeter) and M.S. flat 50x4mm (fifty into four millimeter) including hinges jamb, lock jamb beed and if required angle thrashold of mild steel angle 50x25mm (fifty into twenty five millimeter) welded or rigidly fixed by machanical means, lugs with split end tails to each jambs including steel butt hinges 2.5mm (two point five millimeter) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by Engineer-In-Charge as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing angle iron cup board frame manufactured from M.S. angle iron section of 25x25x5mm (twenty five into twenty five into five millimeter) thickness including hinges jambs, lock jambs beed and if required angle thrashold of mild steel angle 25x25mm (twenty five into twenty five millimeter) welded or rigidly fixed by machanical means, lugs with split end tails to each jambs including steel butt hinges 2.5mm (two point five millimeter) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by Engineer-In-Charge as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing M.S. channel frames 75x40mm (seventy five into forty millimeter) for doors, windows manufactured from ISMC 75x40mm (seventy five into forty millimeter) with M.S. flat 75x4mm (seventy five into four millimeter) in combination welded together to make one frame as per drawing and design including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50x25mm (fifty into twenty five millimetre) welded or rigidly fixed by mechanical means lugs with split end tails to each jamb including iron butt hinges 2.5mm (two point five millimeter) thick with a provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pre-treatment of the surface as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing railing for staircase having ballustres of 19 X 19 mm (Ninetten into nineteen millimetre) M.S (Mild steel) solid square bar with a clear height of 85cm ( eighty five centimetre) and 60cm ( sixty centimetre) centre to centre embedded in cement concrete steps and welded at top along with hand rail of hollow mild steel rectangular pipe of 60x40mm( sixty into forty millimetre) vertical balluster welded or jointed with each other with two rows of mild steel flat 50x5mm( fifty into five millimetre) as per specification, approved drawings, design as per entire satisfaction and direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing M.S. (Mild steel) fan clamps type I of 16 mm (sixteen millimeter) diameter M.S. bar, bent to shape with hooked ends in reinforcement cement concrete slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and laying 600x600mm (six hundred millimetre into six hundred millimeter) vitrified floor tiles (thickness to be specified by the manufacture) of RESTILE/JOHNSON/KAZARIA of approved shade and design with water absorption less than 0.08% ( zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, in flooring laid on 20mm (twenty millimeter) thick cement mortar 1:4 (one cement isto four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( at the rate three point three kilogram/per square meter) including grouting the joints with white cement and matching pigments etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Cement concrete flooring 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and laying 300mmx300mm ( three hundred millimetre into three hundred millimetre) vitrified tiles (thickness to be specified by the manufacturer)of JOHNSON/KAZARIA as per approved shade and design with water absorption less than 0.08% ( zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades in skirting, riser of steps over 12mm (twelve millimeter) thick cement mortar 1:3 (one cement isto three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (at the rate of three point three kilogram/per square meter) including grouting the joints with white cement and matching pigments etcetera complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

White glazed tiles 6mm (six millimeter) thick and size 300mmx300mm (three hundred millimeter into three hundred millimeter) in skirting, risers of steps and dado upto any height on 12mm (twelve millimeter) thick cement mortar 1:3 (One cement isto three sand) and jointed with white cement slurry complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

15mm (fifteen millimetre) thick cement plaster skirting or dado upto any height with cement mortar 1:3 (one cement isto three coarse sand), finished with a floating coat of neat cement including rounding of junctions with floor and curing complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge and carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 40mm (forty millimetre) wide and 4mm (four millimetre) thick glass strips in joints of terrazo/ cement concrete floors complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheet ISI marked Z-120) of TATA/Durashine/Reliance/Jindal over steel truss in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster (RMP), organic coating of 20 (twenty) microns over 5 (five) microns primer coating of back of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted limpet, rubber washers complete with all accessories as required as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing prepainted steel sheet ridges having proper Gola shape or hips of TATA/Durashine/Sail/Reliance/Jindal 60cm (sixty centimetre) overall with 0.60 (zero point six zero millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating plus back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted J or L hooks, bolts and nuts 6mm (six millimetre) diameter) prepainted bitumen washers complete in all respect as per approved drawing, design, specification and as per the direction and entire satisfaction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing prepainted steel sheet valleys of 90 cm (ninety centimeter) wide overall with 0.60mm (zero point six zero millimetre) thick prepainted steel sheet of TATA Durashine/Sail/Reliance/Jindal in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diameter with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 0.63mm(zero point six three millimetre) thick plain galvanished iron sheet with zinc coating not less than 275gm/m2 ( two hundred seventy five gram per square metre) 15cm (fifteen centimeter) wide, 45 cm (forty five centimeter) overall semi-circular plain G.I. sheet gutter with iron brackets 40x3mm (forty into three millimeter) size, bolts, nuts and washers etcetera including making necessary connections with rain water pipes complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing on wall face ISI marked 110mm (one hundred ten millimetre) diameter high pressure PVC rain water pipes of Supreme/Finolex/Vectus/Reliance working pressure not less than 6.00kg/m2 ( six kilogram per square metre) including fixing with approved adhesive etecetra complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing onwall face P.V.C. ( D-plast) accessories for rain water pipe of supreme /Finolex, Vectus/ Reliance including filling the joints with approved adhesive complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government. P.V.C. plain bend 110mm ( one hundred ten millimetre) diameter.

Providing and fixing on wall face P.V.C. (D-plast) accessories for rain water pipe of supreme/Finolex, Vectus/Reliance including filling the joints with approved adhesive complete as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government. P.V.C. plain shoe 110mm ( one hundred ten millimetre) diameter.

Providing and fixing M.S. BP (Black plain) sheet 2mm (two millimetre) thick of TATA/SAIL in eaves board/facia/soffits/ceiling including cutting, fixing and jointing with gas/electric welding to steel roof members and applying a coat of red lead primer complete as per H.P.P.W.D specification, approved drawing and design (frame work is to be measured and paid for separately) including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred millimetre) diameter P.V.C. pipe clips/clamps of supreme/finolex/Reliance of approved design to P.V.C. rain water pipe by means of 50x50x50mm (fifty into fifty into fifty millimeter) hard wood plugs screwed with M.S. screw of required length including cutting brick workand fixing in cement mortar 1:4 (One cement isto four sand) and making good the wall etcetera as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and fixing 8 mm (eight millimeter) thick cement bonded partical board ceiling of approved quality with but jointing and nails complete (frame work and coner fillets to be measured and paid for separately) as per specification, approved drawings, design, entire satisfaction and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate including royality charges, octroi, malkhana, sale tax, GST and all other taxes as imposed by the Government.

Providing and applying 15 mm (fifteen millimeter) thick cement plaster with cement mortar 1 : 6 ( one cement isto six sand) in single coat on rough side of brick / concrete / stone walls for interior plastering up to all floor level including arises, internal, rounded angles ,chamfers and / or rounded angles in all girth and finished even and smooth as per specifications approved drawings, design, as per entire satisfaction and direction of the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Providing and applying 15 mm (fifteen millimeter) thick cement plaster with cement mortar 1 : 4 ( one cement isto four sand) in single coat on fair side of brick / concrete / stone walls for interior plastering up to all floor level including arises, internal, rounded angles ,chamfers and / or rounded angles in all girth and finished even and smooth as per specifications approved drawings, design, as per entire satisfaction and direction of the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Providing and laying 6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3(one cement isto three sand) upto all floor level and curing complete including carriage of materials with in all leads, lifts and other incidental as per specifications, approved drawings, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

White washing with lime on New work (three or more coats) to give an even shade complete in all respect as per specifications, approved drawings, design, as per entire satisfaction and direction of the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Distempering (two or more coats)with oil bound washable distemper of approved brand and manufacture (Nerolac/Asian or its equivalent) and of required shade on undecorated wall surfaces to give an even shade over and including priming coat of distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth priming coat with distemper primer upto all floor level including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Finishing walls with water proofing cement paint of required shade on New work (Two or more coats applied @ 3.84 kg/10 sqm) (three point eight four kilogram/ten square meter) including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Providing and applying white cement based putty of Birla/JK average thickness 1 mm (One millimeter) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Wall painting (two or more coats) with acrylic emulsion paint of approved brand and manufacture and of approved shade for interior grade on undecorated concrete /stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including carriage of materials with in all leads , lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/litre (fifty grams per litre) including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Painting wood work with Deluxe Multi Surface Paint of required shade two or more coats applied @ 0.90 ltr/10 sqm (zero point nine zero litre per ten square meter) over an under coat of primer applied @ 0.75 ltr/10 sqm (zero point seven five litre per ten square meter) of approved brand and manufacture to give an even shade including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Painting steel work with Deluxe Multi Surface Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (zero point nine zero litre per ten square meter) over an under coat of primer applied @ 0.80 ltr/10 sqm (zero point eight zero litre per ten square meter) of approved brand and manufacture to give an even shade including carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Providing plinth protection with 40 mm ( forty millimeter) thick interlocking tiles/ cement concrete paver block with 23 cm ( twenty three centimetre) diameter half round stone ware pipe for drainage purpose laid over 10 cm (ten centimetre) cement concrete 1:4:8 ( one cement isto four coarse sand isto eight graded stone aggregate 40mm (forty millimetre) nominal size) inbedding/haunching complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate including royality charges, octroi, malkana, sale tax,G.S.T. and all other taxes as imposed by the Government.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature up to 80°C (eighty degree C) including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers and connectors etecetra with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge 1216 (One thousand two hundred sixteen) (16mm OD)(sixteen millimetre outer diameter) pipe including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature up to 80°C (eighty degree C) including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers and connectors etecetra with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge 1620 (One thousand six hundred twenty) (20mm OD) ( twenty millimetre outer diameter) pipe including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing to wall ceiling and floor ISI marked 20mm ( twenty millimetre) nominal bore galvanized mild steel tubes (Medium grade) tube fitting and clamps of approved brand and manufacture of TATA/ JINDAL make including making good the wall, ceiling and floor and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (One hundred ten millimeter) diameter P.V.C. ( poly vinyle chloride) pipe clips/ clamps ISI marked of approved design to P.V.C. ( poly vinyle chloride) with steel screws and rawl plugs etecetra complete and cost of cutting holes and making good the walls etecetra including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter P.V.C. ( poly vinyle chloride) pipe clips/ clamps ISI marked of approved design to P.V.C. ( poly vinyle chloride) with steel screws and rawl plugs etecetra complete and cost of cutting holes and making good the walls etecetra including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Making connection of G.I. distribution branch with G.I. main of 25 to 40mm (twenty five to forty millimetre) nominal boare by providing and fixing tee, including cutting and threading the pipe etecetra complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and laying in trenches 110mm (one hundred ten millimeter) diameter high pressure unplasticised Rigid P.V.C. ( poly vinyle chloride) spigot and socket, waste and ventilating pipe having working pressure not less than 6.00 kg/m2 (six kilogramme per square metre) including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter high pressure P.V.C. (poly vinyle chloride) spigot and socket, waste and ventiling pipe having working pressure not less than 6.00 kg/m2 (six kilogramme per square metre) including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) diameter ISI marked P.V.C. plain bend of Supreme/Finolex including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter ISI marked P.V.C. plain bend of Supreme/Finolex including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) diameter ISI marked P.V.C ( poly vinyle chloride) tee including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter ISI marked P.V.C ( poly vinyle chloride) tee including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) diameter PVC ( poly vinyle chloride) Heel rest bend of ISI marked including fixing with approved adhesive etecetra and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter PVC ( poly vinyle chloride) Heel rest bend ISI marked including fixing with approved adhesive etecetra and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) diameter ISI marked PVC ( poly vinyle chloride) collar of Finolex/Prince/Supreme including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter ISI marked PVC ( poly vinyle chloride) Collar of Finolex/Prince/Supreme including fixing with approved adhesive etecetra complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) diameter ISI marked P.V.C. cowl of Supreme/Finolex including fixing with approved adhesive and carriage of materials within all leads, lifts, and other incidentals and as per specification, approved drawings, design as per entire satisfaction and as directed by the Engineer in charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T. and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter ISI marked PVC ( poly vinyle chloride) cowl of Supreme/Finolex including fixing with approved adhesive and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeters) nominal diameter ISI marked high pressure polyvinyl chloride spigot and socket soil waste and ventilating pipe including fixing with approved adhesive etecetra complete f including carriage of materials within all leads, lifts and other incidental charges as per specification, approved drawings, design, as per entire satisfaction and direction of the Engineer-in-charge . The rate including royality charges, octroi, malkhana, G.S.T., sale tax and all other taxes as imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) nominal diameter ISI marked high pressure polyvinyl chloride spigot and socket soil waste and ventilating pipe including fixing with approved adhesive etecetra complete for intel and outlet including carriage of materials within all leads, lifts and other incidental charges as per specification, approved drawings, design, as per entire satisfaction and direction of the Engineer-in-charge . The rate including royality charges, octroi, malkhana, G.S.T., sale tax and all other taxes as imposed by the Government.

Providing and fixing 110mmx90mm (one hundred ten millimeter into ninety millimetre) ) nominal size P.V.C. ( poly vinyle chloride) floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etecetra and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with ISI marked white solid plastic seat and lid, 10 litre (ten litre) low level white P.V.C. ( poly vinyle chloride) flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing white viterous china flat back wash basin size 550x 400 mm (five hundred fifty into four hundred millimeter) of Hindware/Cera make with single 15mm (fifteen millimetre) C.P. brass pillar taps with C.I. brackets, 32 mm (twenty two millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 550x400X180mm.(five hundred fifty into four hundred into one hundred eighty millimeter) stainless steel laboratory sink with C.I. or M.S. brackets painted white C.P. brass chain with rubber plug, 40mm (forty millimetre) C.P. brass waste and 40mm (forty millimetre) C.P. brass trap with necessary C.P. brass unions complete including cutting holes in wall and making good the wall wherever required and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 610x510mm (six hundred ten into five hundred ten millimeter) with bowl depth 200mm (two hundred millimetre) stainless steel kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40mm (forty millimetre) including painting of fittings and brackets, cutting and making good the walls wherever required and carriage of materials with in all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 32mm (thirty two millimeter) diameter rubber plug for wash basin or sink including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 32mm (thirty two millimeter) diameter M.I. Union for wash basin or sink including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 32mm (thirty two millimeter) diameter C.P. brass waste for wash basin or sink including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 100mm (one hundred millimeter) diameter C.P. grating of Jal/Jaugar for gully, floor or nahni trap complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality and colour 450 mm (four hundred fifty millimeter) long towel rail with total length of 495 mm (four hundred ninety five millimeter, 78mm (seventy eight millimeter) wide and effective height of 88 mm (eighty eight millimeter) weighing not less than 170 gms (One hundred seventy grams) including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (forty millimeter) long screws, rawl plugs etcetera complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimeter) breadth 102mm (one hundred two millimeter) height of 75mm (seventy five millimeter) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) diameter C.P. brass pillar tap with capstan head complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) diameter C.P. brass bib tap with capstan head complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) diameter C.P. brass stop cock of Pryag/Hindware/Cera complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 15mm ( fifteen millimetre) nominal bore C.P. brass angle valve of pryag / Hindware/ Cera complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore brass full way valve with wheel complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing 20mm (twenty millimeter) nominal bore brass full way valve with wheel complete including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing brass ball valve (horizontal plunger type) high pressure with polythene plastic float 15mm (fifteen millimeter) nominal bore including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and fixing P.V.C water storage tank of make sintex having capacity of 1000 ltr. (one thousand litre) of ISI: marked 12701 marked G.I inlet and outlet connection, 15mm( fifteen millimetre) nominal bore ball valve and mosquito proof P.V.C cover with locking arrangement including hoisting upto all heights above ground level complete in all respect including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and laying in trenches 150 mm (one hundred fifty millimeter) diameter high pressure P.V.C pipe for disposal of sewarge inluding jointing with approved adhesive complete and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 (one cement isto one and half coarse sand (zone- III) isto three graded stone aggregate 20 mm(twenty millimeter) nominal size), mix foundation concrete 1:4:8 (one cement isto four coarse sand (zone- III) isto eight graded stone aggregate 40 mm (forty millimeter) nominal size) mix, inside plastering 12 mm (twelve millimeter) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20 mm (twenty millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm (ninety into eighty centimeter) and 45 cm (forty five centimeter) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg ( twenty three kilogramme) and weight of frame 15 kg ( fifteen kilogramme) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Constructing masonry Chamber 30x30x50 cm (thirty into thirty into fifty centimeter) inside, in brick work in cement mortar 1:4 (one cement isto four coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (one hundred into one hundred into seventy five millimeter) (inside) with hinged cover fixed in cement concrete slab 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20 mm(twenty millimeter) nominal size), mix including necessary excavation, foundation concrete 1:5:10 ( one cement isto five fine sand isto ten graded stone aggregate 40mm (forty millimeter) nominal size ) and inside plastering with cement mortar 1:3 (one cement isto three coarse sand) 12mm (twelve millimeter) thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (seven point five) including carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement is to Five Sand is to ten graded crushed stone aggregate 40mm (Forty milimetre) nominal size) in haunching of stoneware/ P.V.C pipes of 150mm (One hundred fifty milimetre) internal diameters including necessary form work and curing complete in all respect and carriage of materials within all leads, lifts and other incidentals as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate including royality charges, octroi, malkhana, sale tax, G.S.T and all other taxes as imposed by the Government.

DILRAJ SINGH