1) Supply, Installation, Testing and Commissioning of 2MT EOT Crane. 2) Supply, Installation, Testing and Commissioning of 10MT EOT Crane. 3) Conversion of 2MT and 5MT monorail hoist as EOT crane providing long travel mechanism

Amount

2MT EOT CRANE

Design, fabrication and supply of 2 Ton capacity EOT Crane (including items End carriage with 2 HP Motors and Gear boxes, Cross Travelling Beam 400mm, Cross Travelling Festoon Cable System, Control Panel, Pendent Control Switch, Limit Switches and 2 Ton Wire Rope Hoist)

Bus Bar Shrouded conducting system

Current collector 4 Nos (1 set)

Erection and commissioning of EOT crane including transporting charge

Design, fabrication and supply of long travel beam and rail for 70 mtr length, 5 Nos of cantilever.

Erection, alignment and full welding of above works including transporting charge.

Technical Specification

1.Safe Working Load : 2TON

2.Class of duty : Class II as per IS 807/3177

3.Operation : From the floor with pendent 6 way +on off switch

4.Location : Indoor

5.Height of lift : 6 m

6.Hoisting speed :3.0m/min

7.Cross travel Speed : 15.0m/min

8.Hoist motor rating: 3 hp

9.Cross travel motor rating : 1 hp

10.Cross travel structure: 400 ISMB

11.Hoist brake type: In built AC disc brake

12.CT wheel diameter: EN8 150 mm

13.Drum : Seamless Pipe

14.Wire Rope : Dia. 8/2 Reeving

15.Hoist number of falls: 4

16.Lifting Hook: Single shank,Swiveling type, 'C' hook with safety latch

17.Drum : Seamless Pipe

18.Limit Switch for hoist : Rotary type

19.Limit Switch for CT : Lever type

20.Paint : Ampoxy Grey

21.Power/control voltage: 415V,3Phase, 50 Hz/110V,%) Hz 6 way +on off switch

22. VFD and contactor: Schneider make

10MT EOT CRANE

Design, fabrication and supply of fully electrical SG EOT Crane including End Carriage, Gear Wheels, Axles, Locking Plates, Plumber Blocks, Pinion Wheels, Pinion Shaft, Motor 1.5 HP (2 Nos), Gear Box(2), Cross Travel Festoon Cable System including 6 way pendent switch, Limit Switches, LT Panel Board with 10 Ton capacity Wire Rope Hoist (12.5 HP) with Electric Trolley (2 HP) 6 Mtr lift.

Bus Bar 100 Amps Shrouded Conducting System

Current Collector

Transporting charge, erection and commissioning of crane

Design, fabrication and supply of long travel beam 100 Mtr with above construction specification Technical Specification 1.Long travel beam : 355 mm (JINDAL/SAIL make ) 2.Stiffeners : 75X 8 mm Flat on Flat on 750mm gap on web side of 355 mm beam 3.Base Plate : 10 mm ms Plate 4.Rail: 50 mm Polished Square Shaft

Erection and commissioning of above beam and rail for 10 Ton capacity EOT crane including transporting charge

Technical Specification

1.Safe Working Load : 10 TON

2.Operation : From the floor with pendent 6 way +on off switch

3.Location : Indoor

4.Height of lift : 6 m

5.Single Girder Construction : 600 ISMB JINDAL/SAIL Make +125 X 250mm including Cross Channel and 10 mm stiffeners

6.Hoist motor rating: 12.5 hp

Long travel speed : 15m/min 1.5 hp motor motovario

7.Cross travel motor rating : 2 hp motor

8.Cross travel structure: 400 ISMB

9.Hoist brake type: In built AC disc brake

10.CT wheel diameter: EN8 150 mm

11.LT wheel diameter: EN8 260 mm gear wheel 230 mm dia (50 mm rail)pinion 30mm dia

12.Drum : Seamless Pipe,330mm, RH& LH Type Winding

13.Wire Rope : Dia. 16:4/2 Reeving Usha Martin 6X36fibre core

14.Hoist number of falls: 4

15.Lifting Hook: Single shank,Swiveling type, 'C' hook with safety latch

16.Drum : Seamless Pipe

17.Limit Switch for hoist : Rotary type

18.Paint : Epoxy Primer & Goden Yellow paint

19.Power/control voltage: 415V,3Phase, 50 Hz/110V,1 Ph , 50 Hz Schneider Contactor and Schneider VFD

CONVERSION OF 5MT MONORAIL CRANE AS EOT CRANE

Design, fabrication and supply of fully electrical SG EOT crane including End Carriage, Gear Wheels, Plain Wheels, Axles, Locking Plates, Plumber Blocks, Pinion Wheels, Pinion Shaft, Motor 1.5 HP (2 Nos), Gear Box (2), Cross Travel Festoon Cable System for 2 Hoists including 6 way pendent switch, Limit Switches, LT Panel Board with VFD (Excluding 2 Hoists and Cross Beam)

Current Collector

Transporting charge, Erection and commissioning of crane

Technical Specification

1. Current Collector: Safe track

2. Operation : From the floor with pendent 6 way +on off switch

3.Location : Indoor

4.Height of lift : 6 m

5. Hoist speed: 3.0 m/min

6.Cross travel speed : 15.0m/min

7.Cross Beam : Single Girder Construction 500+ 125X250 mm Box including Cross Channel and 10 mm Stiffeners

8.Long tarvel control box:Schneider

span of 2 MT crane is 6 metres and longitudinal travel 25 metres. Span of 10 MT crane is 11 metres,

stoppers should be provided for longitudinal and cross travel for 2MT and !0 MT cranes.

Warranty condition-3 years from the date of commissioning and handing over.

Necessary approval from the date factory inspectorate is to be obtained.

Painting of the steel structure should be carried out as follows. Clean the metallic surface and apply two coats of epoxy primer over which two coats of golden yellow metallic paint of minimum 75 micron each.

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of installation, testing and commissioning cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR specification and direction of Engineer at site.

Mega Cranes India Pvt Ltd

JKL Agencies

Sagar Industries