Construction of Boiler/Steamer Room,Gas Room and Service area for Ammavasai Mandabam,A/m Mariamman Temple , Samayapuram, Trichy District.

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and FILLING GRAVEL in 'foundation and basement in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Providing and laying crushed stone sand gravel mix (1:1) at the rate of 0.62 cu.m of filling crushed stone sand and 0.66 cum of gravel to consolidated thide of 150mm designed to attain a CBR value of not less than 20 including cost and conveyance of crushed stone sandgravel from approved sources to work site and stacking m3/them to the departmental gauge for premeasurement including labour charges labour charges for power roller watering and all other tools and plants employed including all other incidental charges etc., complete with standard specification

Cement concrete 1:5:10 (one cement, five sand and ten aggregate) using 40mm gauge hard broken blue granite stone jelly for foundation and basement including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification and as directed by the departmental officers.

Brick work in following Cement Mortar 1:5 using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation and basement

Ground floor

Damp proof Course with Cement Mortar 1:4 (One cement & four sand) 12mm thick of the following mixed with water proofing compound of approved quality confirming to ISS @ 2% by weight of cement used as complete complying with standard specification and as directed by the department officers

Supplying and erecting steel centering including necessary supports for plane surfaces for all RCC works including strutting upto 3.29m high in all floors using mild steel shutters of size 90cmx60cm of BG 10 stiffened with mild steel angles of size 25mmx 25mmx3mm laid over silver oak (Country wood) Joists of size 10cmx6.5cm spaced at about 90cm c/c and supported by casurina props of 10cm to 13cm dia. (spaced at 75cm c/c) etc., complete complying with standard specification and as directed by the departmental officers.

For Column footings, column pedestals, plinth beams etc.,

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beam , etc.

For plane surfaces such as rectangular or square RCC columns. sunshades, top and bottom slab of RCC boxing, etc.

Providing and lying in position, standardised Concrete Mix M20 Grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 Kg/M3 and Maximum water cement ratio of 0.55 including admixture (plasticiser/super plasticiser) in recommended proportions as per IS 9103 as accelerate, retard setting of concrete improve workability without impairing strength and durability with about )5 cu.m) 7730 kg of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kg of 10-12mm machine crushed stone jelly and about (4.79 cu.m 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying vibrating wi…

For foundation and basement

For Super structure Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18/20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

For Super structure Ground floor

Special ceiling plastering and finishing the exposed surface of RCC items of work such as slab, beam, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase, step, landing slab etc., including neat finishing and curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

UPVC Window-M0674 Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with Gl/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator-M0675 Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing of Mild steel Grills for doors, windows,open courtyard, grill gate etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specifications.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Dadooing with granite tiles Super fine polished with machine cut edges of synthetic grey, paradise, and similar varieties of suitable sizes 2'0" x 1'0" (or) 1'0" x 1'0" (or) 1'0" x 1'6" of 10 mm thick

Manufacturing, supplying and fixing of Entrance steel doors with the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel in the shutter and welded intact for 1/3 bottom portion of the shutter. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat sand witching the CR sheet in between. Additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 20 kg/sq.m with 300mm hieght of fixed 2 glazing at top with 3mm thick Pin Headed glass inc…

Painting new iron works with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., but excluding cost of priming coat etc., with one coat zinc chloride primer over the existing priming coat complete complying with standard specification and as directed by the departmental officer.

Supplying suitable size casing pipe for 6" dia borewell 6kg/sqem) of best quality with ISI mark with necessary PVC coupling with socket end, The PVC should got approved by the departmental officers-150mm dia

Labour charges for inserting 150 mm dia M.S. Casing pipes assembly (With slots or without slots) in the drilled hole including welding the joints and packing annular space with pebbles of size and quality as approved by the Executive Engineer/TWAD Board

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by 'V' notch method..

Supplying and fixing the PVC end cap of 160mm dia at the of PVC casing pipe etc., complete complying with standard specification. The bore cap should be got approved by the Exe.engineer before use on works.

Supplying & fixing of 2.0 H.P Borewell submergible with with heavy duty double cylinder air lifting compressior with stand pulli guard with 2hp 1440 Rpm 220V,50 Hz, 220V, single phase TEFC heavy duty motor complete set with Vee belt& Foot valve Pump size water pipe 1" and air pipe 1/2"

Supplying of best and approved quality of HDPE pipe of following size including laying in the basement and tying with copper wire etc., complete complying with standard specification-50mm dia

50mm dia HDPE pipe

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Upto 5 HP

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg./sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works-Below Ground Level

32mm dia UPVC pipe BGL

Supplying and fixing the following UPVC specials of heavy type of approved quality and good variety of various sizes excluding fixing charges, but including cutting and threading of pipes as directed by the departmental officers etc., complete complying with standard specification. UPVC specials should be got approved by the departmental officers before use on work.

32 mm dia UPVC Coupling

32mm dia UPVC Elbow

32 mm dia UPVC Tee

32 mm dia UPVC Union

25mm dia UPVC Elbow

25mm dia UPVC Coupling

25 mm x 20 mm Dia Reducer Elbow

Supplying fixing and connecting of 4 sq.mm seathed 3 core cable wire for the sub-mergible motor from pannel board to sub-mergible pump including rope etc., complete.

Supplying and fixing wall mounting of Panel board with following accessories a. Suitable DOL type push botton automatic starter for for 2HP Bore well compressior

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. External Water supply above Ground level

32 mm dia UPVC Pipe

25 mm dia UPVC Pipe

20 mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. UPVC Coupling

40 mm dia

32 mm dia

UPVC Elbow 40 mm dia

32 mm dia

25 mm dia

20 mm dia

UPVC Tee 40 mm dia

32 mm dia

UPVC Hex Nipple 40 mm dia

32 mm dia

UPVC Union 40 mm dia

32 mm dia

UPVC Reducer Elbow 32 x 25 mm dia

25 x 20 mm dia

Supplying and fixing in position 15mm dia brass CP swan nech tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC/MS clamp, teak wood plugs, brass screws, etc.,

110mm dia PVC

75mm dia PVC

Supplying and fixing position PVC Nahani Trap (The Nahani Trap should be got approved by the Executive Engineer before use on works) 100 x 75mm with PVC grating

Supplying and fixing PVC water tank etc., complete.

Supplying and fixing Gate Valve

40mm dia gate valve

32mm dia gate valve

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Sub Total

Sudhakar (BID ID -1409004)