PROVN OF TILING OF JCOS ACCN BLDG NO 8 AND SPL REPAIR OF COMPLETE WIRING IN VIP BLOCK TRISHUL NANDA DEVI GANGOTRI YAMUNOTRI KAILASHKOT NANDKOT KAMET LIPULEKH AND CHAUKHAMBA AT AR AND RC AT NAINITAL UNDER GE RANIKHET

Amount

BOQ ( Sch 'A') B/R items Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material & Labour for coloured non skid ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc. 0.11 sqm but n.exc. 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigment over with and including 15mm thick bedding layer in CM 1:6 complete all as specified and directed.

Material & Labour for 300x200x7mm thick glazed ceramic digital tiles coloured, design and pattern as approved fixed as in vertical surface such as skirting, dado and riser to steps etc, set and jointed in neat cement slurry and pointed with white cement with colour pigment to match complete all as specified and directed.

M&L for virified tiles 8 to 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and hite or coloured cement to match as in floors etc. set and jointed in neat cement slurry over with and including screed bed of 15 mm thick in CM 1:6 and pointed in white or coloured cement to match as in floor etc , all as specified.

M&L for virified tiles 8 to 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in verticle surfaces etc etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over with and including screed bed or bedding layer 10mm thick in CM 1:4 on vertical surfaces/skirting complete all as specified and as directed

Taking down carefully copper /aluminium point wiring (light,fan,socket or power ) complete fittings such as switches and fixtures ceiling roses, pendants, regulators, sockets, lamp holders, bracket light fittings, bulk heads fittings, tube light fittings etc removing the materials from site and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

Supply & fixing point wiring for one light point/ fan/ bell point / 5 Ampere socket outlet point (independent point) controlled by one, one way switch with 1.5 Sqmm size, PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia )with all fittings and accessories fixed concealed (including chase cutting in brick/stone/precast PCC block masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and including modular metal flush box for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with modular cover plate with frame and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size copper conductor cable (FRLS) as in earth wire and connected to common earth dolly complete all as specified and directed

All as per item No 07 above but one light point controlled by two way switch.

All as per item No 07 above but wiring with 2.5 Sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) cable and 2.5 sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) earth wire for socket outlet 5 pin 15 Amps controlled by one, one way switch on same board.

All as per item No 07 above but wiring with 2.5 Sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) cable and 2.5 sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) earth wire for socket outlet 5 pin 15 Amps controlled by one, one way switch on independent board.

All as per item No 07 above but wiring with 4 Sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) cable and 4 sqmm PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) earth wire for socket outlet 3 pin 15 Amps controlled by one, one way switch on independent board.

S&F switch modular type single pole, one way 10 Amp, 1 module complete all as specified and directed.

S&F switch modular type, two way 10 Amp, 1 module complete all as specified and directed

S&F socket out let modular type, 2/3 pin combined 2 module, 6/10 Amps, complete all as specified and directed.

S&F switch modular type single pole, one way 16/20 Amp, 1 module complete all as specified and directed.

S&F socket out let modular type, 2/3 pin combined 2 module, 6/16 A or 10/20 Amps, complete all as specified and directed.

S&F ceiling rose, PVC/ Poly carbonate,isolated body three terminal complete all as specified and directed.

S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

S & F call bell ding dong AC, 230V single pole complete all as specified and directed.

S&F bell push modular type single pole, one way 6 Amp, one module complete all as specified and directed.

Supply and fix High quaity LED light fitting 1x20 W,220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed.

Supply and fix LED Bulb 9 Watt complete all as specified and directed.

Taking down carefully and refixing of light fittings any type( wall/bracket/bed lamp/ ceiling fitting or any other fittings) and any size with/without driver, holder including repair works such as painting of wall/bracket lights as required and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed.

S & F in repair MCB single pole, 240 volts, 20 to 40 Amp, rupturing capacity 10 KA, ‘B’ curve type in the MCB DB including taking down complete all as specified and directed.

S & F in repair MCB single pole and neutral, 240 volts, 40 to 63 Amp, rupturing capacity 10 KA, including taking down complete all as specified and directed.

S & F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral,12 ways including blancking plate with 200 Amp rated bus bar, 240 volts fixed sunk / flush to the wall or niche complete all as specified and directed.

S&F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 240 Volts 20 Amps complete all as specified and directed.

Taking down carefully and refixing of existing sheet metal enclosures for DB’s (Double door type) incl MCBs any type & rating, 8/12 ways including blancking plate, fixed sunk / flush to the wall or niche incl connection with wire and thimbles and plastering the external surfaces and matching the same with existing suface complete all as specified and directed.

S & F MCB FP , 415 volts, AC B curve, 10 KA , 63 to 100 Amp complete all as specified and directed.

S&F sheet metal enclusure for DBs(double door type) prewired Triple pole and neutral 12 way including blacking platge as required with 200 Amps rated bus bar, 415 volts fixed complete all as specified and directed.

S&F sub main wiring with two single core FRLS PVC insulated and sheathed 1100 Volts grade, 10 Sqmm size cables, PVC insulated multi-stranded copper conductor fixed in & including PVC conduit pipe 25mm dia with all accessories and one continuous run of 6.0 Sqmm copper conductor PVC insulated multistanded copper conductor as earth (Note :- Two single core cables along with earth wire and conduit shall be measured as one unit length).

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost by the contractor.

M&L for earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised iron strip 32x6mm as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 40 mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised Iron/steel of size 75mm x75mm x 25mm, supplying and laying charcoal stone aggregate) chamber and mild steel angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded crushed stone aggregate reinforced with 8 mm dia TMT bars @ 75mm C/C both ways with mild steel handle 12 mm dia, PGI funnel with wire mesh, 20 mm dia GI pipe light grade for watering all as shown in drawing with complete all as specified and directed Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 40mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost by the contractor.

Supply & Fixing LED street light fitting 35W, 230V AC outdoor type with high pressure die cast aluminium IP66 roadway luminaire with high power LED as light source and electronic driver including GI bracket light grade with impact and corrosion resistant including thermal management in multiple optics and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded aluminium conductor cable complete including taking down existing old light fitting any type all as specified and directed.

S & F LED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed.

Supply and fix High quility LED lighting fixture mirror type with high output diffuser 2 feet 1x 5 Watt. 220V AC,complete with polycarbonate tube, white/warm white suitable for mirror light internally pre wired of 1.5 sqmm three core flexible cable complete all as specified & directed.

Taking down storage type water heater (geyser) of any type /make up to 50 Ltr capacity after disconnecting electric / water connections and refixing the same after carrying out necessary repairs including reconnecting the electric / water connections and testing complete all as specified and diected.

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 4 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50.0 sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120.0 sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95.0 sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70.0 sq mm 3.5 core complete all as specified and directed.

Excavation in trenches in hard/dense soil not exc 1.5 mtrs wide and not exc 1.5 m in depth for laying cables and getting out incl jointing bottom surface to the reqd level/slope etc complete all as specified and directed.

Returning, fillingin, including spreading, leveling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed.

Removing excavated material (soil) to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note : Punned down thickness of sand shall be considered for measurement and payment.

Material and labour for brick cable cover protection to cable using old size class 'B' bricks (230x115x75mm size), laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as specified and directed.

M&L for 40mm bore GI pipe light grade with and includning all GI fittings as in protection pipe for cable fixed to pole or laid in trenches/ floor for mechanical of protection of cable complete all as specified and directed.

M&L for 50mm bore GI pipe light grade with and includning all GI fittings as in protection pipe for cable fixed to pole or laid in trenches/ floor for mechanical of protection of cable complete all as specified and directed.directed.

M/S ABHI ASSOCIATES

Ramsons