PROPOSED GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

One percent of the Estimated cost of work put to tender shall be recovered from the running bills of the contractor as testing charges,

after deducting the cost of material proposed in scheduled-A at basic rate. One percent labour cess will be deducted from contractor’s

I/ We am/are willing to carry out the work at _____________________% above / below _____________________________%

(should be writtern in figure and words)

below / above the estimated rates mentioned above amount of my / our tender works out as under :-

Estimated amount put to tender : Estimated amount put to tender :

Signature of contractor Chief Officer

CHORWAD NAGARPALIKA

1) All the work shall be carried out as per MOST specification and specification on the division or as directed.

Rates quoted includes clearance of site (prior to commencement of work and at its closed) in all respects and held gross for

2) under all conditions, site moisture weather etc.

In RCC item when there is change in grade of concrete mix or change in consumption of cement as per actual mix design

then the difference in consumption of cement shall be deducted from the rate of original item valued at the star rate as

3) mentioned in tender. However no extra payment shall be made for use of additional Quantity of cement as per actual

concrete mix design. Concrete mix design shall be done in GERI laboratory only.

The Contractor shall exhibits a board as per Govt. circular No. 2DK – 3277 / 1657 N Dt. 26–01-73 with detail of specification

4) and details of work and amount involved at site without any payment as directed by the Engineer in charge.

Testing of materials be as per statement attached with the Specifications, the materials shall be tested in G.E.R.I. Bill for

5) testing shall be paid by the Executive Engineer and 1% of the (one percent) of amount put to tender after shall be recovered

from the running account bills of the works. (As per G.R. (R&B) Deptt., No. TNC/1085/4/C dtd. 20.12.91.

6) The contractor shall quote even "NIL" if no reduction is proposed.

One precent of estimated cost put to tender for this work shall be recovered from the contract payments as "LABOUR CESS".

7) In terms of the Gujarat Government Gazette Extra ordinary dated 12.12.04. Implementation of building and other

construction workers regulation of equipments and conditions of service Act-1996)

8) Photographs of before work and after work will be submitted by the contractor at the time of each bill submission.

9) GST Will be Paid Extra as Actual Bill Amount.

10) The base amount of Rs. 3,68,918.00 will be recovered from the 1st RA Bill of this work towards salvage value of dismantled

material available from dismantling the existing structure irrespective of the quantity of material actually received on site.

11) Additional pro-rata amount for salvaged material will be recovered from the 1st RA Bill of this work towards salvage value of

dismantled material available from dismantling the existing structure, based on recorded quantity on site of extra material

other Paver Block, Steel and bela stone.

Signature of contractor Chief Officer

CHORWAD NAGARPALIKA

CHORWAD NAGARPALIKA

CHORWAD, DIST. JUNAGADH

Name of Project : PROPOSED GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

Name of Work : CONSTRUCTION WORK FOR GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

SCHEDULE - "B1"

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

1 Excavation for foundation up to 1.5 Meter depth including

sorting out and stacking of useful materials and

disposing of excavated stuff up to any lead. (a) For Loose Rupees One Hundred

or Soft soil Twenty Two and Ninety

168.41 122.94 Four Paise m3

2 Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead. (B)

Dense or Hard soil Rupees One Hundred Fifty

104.76 157.16 Seven and Sixteen Paise m3

3 Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff upto any lead. (E) Hard Rupees Six Hundred

Rock Twenty Seven and Forty

111.24 627.48 Eight Paise m3

4 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

exceeding 20 cm. In depth consolidating each deposited Rupees One Hundred

layer by ramming and watering Thirty Six and Ninety Two

5 Filling in foundation and plinth with Murrum or selected

soil in layers of 20cm. thickness including watering, Rupees Three Hundred

ramming and consolidating etc. complete. One and Seventy Eight

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

6 Filling in foundation and plinth with black garden soil in Rupees Two Hundred

any thickness completed. Seventy Three and

41.45 273.71 Seventy One Paise m3

7 Providing and laying cement concrete 1:2:4 (1-Cement :

2-Coarse sand : 4- graded stone aggregates 20 mm

nominal size) and curing complete excluding cost of Rupees Three Thousand

formwork in (A) Foundation and Plinth Eight Hundred Five and

102.46 3805.29 Twenty Nine Paise m3

8 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Four Thousand Six

work in : RCC Column Footings Hundred Ninety Three and

61.14 4693.47 Forty Seven Paise m3

9 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Seven Thousand

work in : RCC Column up to Plinth Level. Two Hundred Thirty Seven

8.79 7237.66 and Sixty Six Paise m3

10 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Seven Thousand

work in : RCC Columns for Ground Floor Two Hundred Thirty Seven

35.01 7237.66 and Sixty Six Paise m3

11 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Five Thousand

work in : RCC Plinth beams Four Hundred Forty and

24.17 5440.87 Eighty Seven Paise m3

12 Providing laying Controlled cement concrete M-200 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Five Thousand

work in : RCC Floor Beams at GF Slab level. Eight Hundred Seventy

20.63 5875.17 Five and Seventeen Paise m3

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

13 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete

work in : RCC Slabs & Landings Rupees Six Thousand Sixty

38.47 6064.04 Four and Four Paise m3

14 Providing laying Controlled cement concrete M-250 and

curing complete including the cost of form work and

excluding cost of reinforcement for reinforced concrete Rupees Six Thousand One

work in : RCC lintel Hundred Fifty Three and

5.58 6153.93 Ninety Three Paise m3

15 Providing and TMT bar FE 500/500D reinforcement for

R.C.C. work and including bending, binding & placing in

position completed up to floor two level. Rupees Seventy Seven and

25299.50 77.29 Twenty Nine Paise Kg.

16 White Stone Bela Masonry block in course in super

structure with stone of approved quality in lime mortar

1:6 (1-cement : 6-coarse sand) including packing the Rupees Six Thousand Four

joints etc. complete. (up To 10 ton) Hundred Seventy Nine and

37.06 6479.69 Sixty Nine Paise m3

17 White Stone Bela mesonry work in partition walls upto

cm thickness in cement Mortar 1:4 ( 1-Cement : 4-

course sand) Rupees Six Hundred Eighty

86.83 684.49 Four and Forty Nine Paise m2

18 20mm thick sand faced cement plaster on walls up to

10 meter above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3- fine sand) and

mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) Rupees Three Hundred

etc. complete. Forty Two and Forty Two

19 Providing 15mm thick cement plaster in single coat on

rough (Similar) side of single or half brick walls for

interior plastering up to floor two level and finished even Rupees One Hundred

and smooth in (i) C.M. 1:3 (1-cement : 3- sand) Ninety Five and Forty

511.69 195.43 Three Paise m2

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

20 Providing 10mm thick cement plaster in single coat on

brick/concrete Slab for interior plastering up to floor two

level and finished even and smooth in (i) C.M. 1:3 (1-

cement : 3- sand) Rupees One Hundred Forty

307.72 145.66 Five and Sixty Six Paise m2

21 Extra over above item for plastering on ceilings and sofits

of stairs upto floor two level instead of plastering on

walls. Rupees Twenty Six and Six

22 Finishing wall with base coats of wall primer of approved

brands and above weather proof exterior emulsion

paint on wall surface (Two coats) to give an required

shape even shade after thoroughly brushing the surface

to remove all dirt, and remains of loose powdered Rupees One Hundred

materials etc. complete Thirty Six and Seventy

1074.72 136.79 Nine Paise m2

23 Applying Two coats of Birla or Asian Acrylic Lappy (putty)

and two coats of primer of approved brand and

manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand

papered smooth. Rupees Forty and Sixty

24 Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth Rupees Eighty Two and

819.41 82.86 Eighty Six Paise m2

25 Painting two coats (including priming coat) on new steel

and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning the

surface an even shade including cleaning the surface of Rupees One Hundred

all dirt, dust and other foreign matter. Twenty Eight and Ninety

86.07 128.95 Five Paise m2

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

26 Supply & plantation of shrubs are to be planted as per

the detailed planting drawing and specify distance,

labour charges, for digging of pit as per detailed

specification filling of organic manure, fertilizer,

insecticides etc. and planting of plant as shown in the

drawing, filling the pit, proper pressing and watering.

complete including maintenance for 3 years with

watering, organic manure, isecticides to be applied time

to time wherever required. also damaged or dry plant

Rupees Two Hundred Sixty

which is not grow up, to be replaced complete.

61.00 260.58 and Fifty Eight Paise No

27 Providing and laying Granite slab (18mm thick) slab

flooring over 20mm (Average) thick base of cement

mortar 1:6 (1-cement : 6-Coarse sand) or L.M. 1:1.5 laid

over and jointed with grey cement slurry including

rubbing and polishing complete (Basic Granite rate shall Rupees Two Thousand

be 250/Sft) (A) Granite slab 18mm thick Four Hundred Eighteen and

23.97 2418.55 Fifty Five Paise m2

28 Providing and laying 18mm thick Granite slab in riser of

steps Dedo and pillars laid 10mm thick Cement Mortar

1:3 (1-Cement : 3-Coarse Sand) and jointed with Grey Rupees Two Thousand Five

Cement Slurry including rubbing and polishing complete. Hundred Two and Seventy

6.92 2502.78 Eight Paise m2

29 Providing and laying coloured glazed tiles of the size

skirting, risers of steps and Dedo on 10 mm. thick

cement plaster 1:3 (1 cement : 3 coarse sand) & jointed Rupees One Thousand Four

with white cement slurry. Hundred Eighty Eight and

51.03 1488.24 Twenty Four Paise Sqm

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

30 Providing and fixing 35mm thick shutter for doors,

windows and clerestory windows including Indian teak

wood frames 12cm x 7cm. Size including anodized

aluminium fixtures and fastenings including primer coat

of approved quality and two coats of oil painting etc, Rupees Five Thousand

complete. (ii) Fully Panelled. Three Hundred Thirty Eight

15.58 5338.31 and Thirty One Paise m2

31 Providing and fixing FRP frame size 125x65 mm and

35mm thick FRP shutter with wood grain raised panneled

design finish shutter having extra reinforcement on sides

& edges in Gel coat finish. The core of the shutter &

frame is to be filed up with injected polyurethene foam

done in situ along with embedded wooden pieces for

stiffening & also taking hinges & fintures. The whole FRP

frame & shutter is to be water proof weather proof,

termite proof & resistance to mild acid/alkali. Rates are

to be inclusive of S.S hinges with fastener sleeve & Rupees Two Thousand

alluminium fixtures & fastenings. Nineteen and Ninety Eight

32 Providing and laying cement concrete flooring 1:2:4 (1-

cement : 2-coarse sand : 4-graded stone aggregate

20mm nominal size) laid in one layer and finished with a

floating coat of neat cement. (B) 50mm thick. Rupees Three Hundred

245.52 339.08 Thirty Nine and Eight Paise m2

33 P & L 24" x 24" vitrified 8 mm thick tile flooring over

20mm (average) base of cement mortar 1:6 (1 cement:

6 coarse sand) on new surface or fixing on existing

flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry

Rupees One Thousand

including finised with flush pointing & cleaning the

Three Hundred Fifty Four

surface etc. complete for DARK shade

72.85 1354.62 and Sixty Two Paise m2

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

34 Providing and laying broken china mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope

and to be tempered to bring mortar crème out up to

surface using white cement including rounding off

junctions and extending them up to 15cm along the wall

Rupees Seven Hundred

clearing with water and oxalic acid etc. as directed

Seventy Nine and Seventy

35 Providing and fixing standared extruded of alluminium

section of size 63mm x 38.10mm x 1.2mm @ Wt.

Kg/mt with colour anodized alluminium frame for

ventilation with 5 mm thick frosted glass as details etc Rupees One Thousand One

complete for Ventilation Hundred Seventy Five and

3.10 1175.56 Fifty Six Paise m2

36 Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at

required spacings and frame alround, square or round

bars with round headed bolts and nuts or by screws (A)

Plain Grill. Rupees One Hundred Six

860.85 106.24 and Twenty Four Paise Kg

37 Box cutting the road surface to proper slope and camber

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto any lead. Rupees One Hundred Nine

34.00 109.42 and Forty Two Paise m3

38 Providing and fixing pre-cast Rubber Dye / steel Dyeinter

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and

as per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the

joint with sand in proper line and level as per guidlines of

IRC : SP 63-2018 etc. Complete.

Rupees Seven Hundred Six

249.92 706.93 and Ninety Three Paise m3

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

39 Providing and fixing (Vyara or Equivalent Brands) pre-

cast Rubber Dye / steel Dye inter locking Square

concrete block Size 200 X 200 X 80 mm thick with grade

of concrete M400 pneumatic compressed / vibrated

mechanically and as per approved design and Colours of

Paver Block Said by AVKUDA Authorized Person

Confirming to IS 15658 : 2006 including 35 mm Sand

layer for levelling and filling the joint with sand in proper

Rupees One Thousand

line and level as per guidelines of IRC : SP 63-2018 etc.

Three Hundred Ninety Six

4.50 1396.43 and Forty Three Paise m2

40 Providing Erecting and fixing coated PVC. (ISI) water

tank of required capacity each with all necessary fittings

and connection etc. complete on terrace. Rupees Three and Ninety

2000.00 3.95 Five Paise Lt.

41 Providing laying and jointing in true line and level 40mm

dia. U.P.V.C. Pipe (SCH-40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

Rupees One Hundred Forty

of all materials.

18.00 148.12 Eight and Twelve Paise Rmt

42 Providing, laying and jointing in true line and level 25mm

dia. U.P.V.C. Pipe (SCH-40) line including fitting as

approved by Engineer-in-Charge. Pipe shall be fixed on

the wall with the help of clamp at every two meter C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all

Rupees Ninety One and

materials. (D) 25mm dia pipe

30.00 91.84 Eighty Four Paise Rmt

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

43 Providing, laying and jointing in true line and level 50mm

dia. U.P.V.C. Pipe (SCH-40) line including fitting as

approved by Engineer-in-Charge. Pipe shall be fixed on

the wall with the help of clamp at every two meter C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the

Rupees One Hundred

same with adhesive solvent, including cost of all

Ninety Five and Sixty

materials. (D) 50mm dia pipe

30.00 195.67 Seven Paise Rmt

44 Providing laying and jointing in true line and level 32mm

dia. U.P.V.C. Pipe (SCH-40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

Rupees One Hundred

of all materials.

30.00 119.15 Nineteen and Fifteen Paise Rmt

45 Providing laying and jointing in true line and level 15mm

dia. U.P.V.C. Pipe (SCH-40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

Rupees Seventy Two and

of all materials.

30.00 72.65 Sixty Five Paise Rmt

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

46 Providing, laying and jointing in true line and level

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and Rupees Eight Hundred

jointed with adhesive solvent cement including cost of all Seventy Six and Ninety

60.00 materials. 876.91 One Paise Rmt

47 Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and Rupees Five Hundred

making good the walls. Eighty Six and Twenty

6.00 586.28 Eight Paise EA

48 Providing and fixing brass screw down stop (A) 15 mm.

Dia Rupees Two Hundred Five

6.00 205.83 and Eighty Three Paise EA

49 Providing and fixing Pillar Tap, capstan head, screw down

high pressure with screws, shanks and back nuts (A) 15 Rupees Three Hundred

mm. Dia Eight and Seventy Three

6.00 308.73 Paise EA

50 Providing and Fixing of Fix Glass of 12mm Tafan Glass

with all Neccesary Fitting of Approved make Standard

Industry Practice as per Instruction of Engineer-in- Rupees Five Thousand Six

Charge and all Complete. Hundred Seventy Eight

102.28 5678.33 and Thirty Three Paise m2

CHORWAD NAGARPALIKA

CHORWAD, DIST. JUNAGADH

Name of Project : PROPOSED GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

Name of Work : Proposed Gym Equipment for Gym and Fitness Center at Chorvad Dist. Junagadh

SCHEDULE - "B2"

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

1 Supply & installing of Trade Mill of Jerai Or equivelant make

made 6 hp moter, 200 kg user weight capacity 22 level auto

incline 1 to 22 km max speed 5 year motor warranty and

year free service standard make including all harware and Rupees Two Lac Sixty

fixtures of standard make complete as per detail Seven Thousand Seven

specification and instruction of consultant. Hundred Twenty Five and

2.00 267725.75 Seventy Five Paise Set

2 Supply & installing of Air Bike Or equivelant make made

with air resistance and 180 kg user weight capacity and

manual break with display make including all hardware & Rupees Fifty Eight

fixtures of standard make complete as per detail Thousand Two Hundred

specification and instruction of consultant. One and Twenty Five

3.00 58201.25 Paise Set

3 Supply & installing of Body Twister commercial model of

Jerai Or equivelant make made from 4" X 2" square

gauge CRCA pipe, 2" X 2" square 14 gauge CRCA pipe, 1" &

2" dia CRCA pipe 14 gauge CRCA pipe high quality powder

coated, seat work made from 18mm ISI mark plywood with

2" thk PU foam and high density rexene of standard make

including all harware and fixtures of standard make

Rupees Twenty Nine

complete as per detail specification and instruction of

Thousand One Hundred

1.00 29100.63 and Sixty Three Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

4 Supply & installing of Multi Adjustable bench only of Jerai

Or equivelant make made from 4" X 2" square 12 gauge

CRCA pipe high quality powder coated, seat work made

from 18mm ISI mark plywood with 2" thk PU foam and high

Rupees Fifty Eight

density rexene of standard make including all harware and

Thousand Two Hundred

fixtures of standard make complete as per detail

One and Twenty Five

specification and instruction of consultant.

3.00 58201.25 Paise Set

5 Supply & installing of Multi Purpose bench only for flat,

Incline, Decline, Leg extension and Squat purpose of Unique

Gym Equipment Pvt. Ltd. Or equivelant make made from 2"

X 2" square 14 gauge CRCA pipe high quality powder

coated, seat work made from 18mm ISI mark plywood with

2" thk PU foam and high density rexene of standard make

Rupees Thirty Three

including all harware and fixtures of standard make

Thousand Seven Hundred

complete as per detail specification and instruction of

Fifty Six and Seventy

1.00 33756.73 Three Paise Set

6 Supply & installing of Peck Deck Jerai Or equivelant make

made with the Tube thickness - 2.5 mm and wight thickness

- 100 kg , N.W. - 270 kg and G.W. - 307 kg including all

harware and fixtures of standard make complete as per Rupees One Lac Seventy

detail specification and instruction of consultant. Six Thousand Nine

Hundred Thirty One and

1.00 176931.80 Eighty Paise Set

7 Supply & installing of Let pull dow for back Jerai Or

equivelant make made with the Tube thickness - 2.5 mm

and wight thickness - 100 kg, N.W. - 270 kg and G.W. -

kg including all harware and fixtures of standard make Rupees One Lac Seventy

complete as per detail specification and instruction of Six Thousand Nine

consultant. Hundred Thirty One and

1.00 176931.80 Eighty Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

8 Supply & installing of Bicep + Tricep machine of Jerai Or

equivelant make made with the Tube thickness - 2.5 mm

and wight thickness - 100 kg , N.W. - 270 kg and G.W. -

307 kg including all harware and fixtures of standard make Rupees One Lac Seventy

complete as per detail specification and instruction of Four Thousand Six

consultant. Hundred Three and

1.00 174603.75 Seventy Five Paise Set

9 Supply & installing of Functional Trainer machine of Jerai Or

equivelant make made with the Tube thickness - 2.5 mm

and wight thickness - 100 kg, N.W. - 270 kg and G.W. -

kg including all harware and fixtures of standard make Rupees Two Lac Ninety

complete as per detail specification and instruction of Six Thousand Eight

consultant. Hundred Twenty Six and

1.00 296826.38 Thirty Eight Paise Set

10 Supply & installing of Leg Extension with Curl jerai company

Or equivelant make made from 4" X 2" square 12 gauge

CRCA pipe, 2" X 2" square 14 gauge CRCA pipe, 1" dia

CRCA pipe 14 gauge CRCA pipe high quality powder coated,

and 18mm MS bright bar for plates stack guide rod & 1" dia

MS bright bar for centre rod high quality nickel chrome

coated bar. pulley bearing should be 6201ZZ of standard

make. weight stack 15 plates, - 100 kg each plate should

not less than 5 kg. Seat work made from 18mm ISI mark

plywood with 2" thk PU foam and N.W. - 243m kg and G.W.

- 274 kg and high density rexene of standard make with

flexible arrangement including all harware and fixtures of Rupees One Lac Eighty

standard make complete as per detail specification and Thousand Four Hundred

instruction of consultant. Twenty Three and Eighty

1.00 180423.88 Eight Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

11 Supply & installing of Seated Leg Press of Jerai. Or

equivelant make made Size - 2170 x 1610 x 1260 mm

standard make with flexible arrangement including all Rupees Two Lac Fifteen

harware and fixtures of standard make complete as per Thousand Three Hundred

detail specification and instruction of consultant. Forty Four and Sixty

1.00 215344.63 Three Paise Set

12 Supply & installing of Lateral rise Shoulder Press machine

of Jerai Or equivelant make made from standard make with

flexible arrangement including all hard ware and fixtures of

standard make complete as per detail specification and Rupees Twenty Thousand

instruction of consultant. Nine Hundred Fifty Two

1.00 20952.45 and Forty Five Paise Set

13 Supply & installing of Cable cross over machine for chest of

jerai with weight stake 95 kg x 2 N.W. - 411 Kg and G.W. - Rupees Two Lac Eighty

466 Kg standard make including all harware and fixtures of Five Thousand One

standard make complete as per detail specification and Hundred Eighty Six and

1.00 instruction of consultant. 285186.13 Thirteen Paise Set

14 Supply & installing of Air rover machine for chest of jerai Or

equivalent with Air resistance 180 kg user weight capacity

plus 2 year warranty standard make including all harware Rupees Ninety Eight

and fixtures of standard make complete as per detail Thousand Nine Hundred

specification and instruction of consultant. Forty Two and Thirteen

1.00 98942.13 Paise Set

15 Supply & installing of Chin up machine for Shoulder of jerai

Or equivalent Tube thick - 2.5 mm, weight stake - 100 Kg

and N.W - 321 Kg, G.W. - 377 Kg standard make including Rupees One Lac Seventy

all harware and fixtures of standard make complete as per Six Thousand Nine

detail specification and instruction of consultant. Hundred Thirty One and

1.00 176931.80 Eighty Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

16 Supply & installing of Row machine for Shoulder of jerai Or

equivalent Tube thick - 2.5 mm, weight stake - 100 Kg and

N.W - 229 Kg, G.W. - 260 Kg standard make including all Rupees One Lac Seventy

harware and fixtures of standard make complete as per Four Thousand Six

detail specification and instruction of consultant. Hundred Three and

1.00 174603.75 Seventy Five Paise Set

17 Supply & installing of Wrist curl machine for Shoulder of

jerai or equivalent standard make including all harware and Rupees One Lac Fifty

fixtures of standard make complete as per detail Seven Thousand One

specification and instruction of consultant. Hundred Forty Three and

1.00 157143.38 Thirty Eight Paise Set

18 Supply & installing of Aductor + abductor machine for

Shoulder of jerai Or equivalent Tube thick - 2.5 mm

weight stake - 80 Kg and N.W - 248 Kg, G.W. - 278 Kg

standard make including all harware and fixtures of Rupees One Lac Seventy

standard make complete as per detail specification and Four Thousand Six

instruction of consultant. Hundred Three and

1.00 174603.75 Seventy Five Paise Set

19 Supply & installing of Dual asix machine for Shoulder of

jerai with weight stake 95 kg x 2 Or equivelant make made

from 4" X 2" 12 gauge & 2" X 2" 14 gauge square CRCA

pipe, 1" & 2" dia 14 gauge CRCA pipe high quality powder

coated, and 18mm MS bright bar for plates stack guide rod

& 1" dia MS bright bar for centre rod high quality nickel

chrome coated bar. pulley bearing should be 6201ZZ of

standard make. weight stack 15 plates, each plate should

not less than 5 kg. Seat work made from 18mm ISI mark

plywood with 2" thk PU foam and high density rexene of Rupees Eighty One

standard make including all harware and fixtures of Thousand Four Hundred

standard make complete as per detail specification and Eighty One and Seventy

1.00 instruction of consultant. 81481.75 Five Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

20 Supply & installing of Arm Curl machine for Shoulder of

jerai or equivelant make made from standard make Rupees One Lac Forty

complete as per detail specification and instruction of Five Thousand Five

consultant. Hundred Three and

1.00 145503.13 Thirteen Paise Set

21 Supply & installing of Shrugs dead lift machine for Shoulder

of jerai or equivelant make made from standard make Rupees Two Lac Twenty

complete as per detail specification and instruction of Six Thousand Nine

consultant. Hundred Eighty Four and

1.00 226984.88 Eighty Eight Paise Set

22 Supply & installing of Seated calf machine for Shoulder of

jerai or equivelant Size - 1500 x 700 mm x 1000 mm make

made from standard make complete as per detail Rupees Forty Six

specification and instruction of consultant. Thousand Five Hundred

1.00 46561.00 Sixty One Only Set

23 Supply & installing of Web bord machine for Shoulder of

jerai or equivelant Size - 1380 mm x 680 mm x 690 mm Rupees Fifty Two

make made from standard make complete as per detail Thousand Three Hundred

specification and instruction of consultant. Eighty One and Thirteen

1.00 52381.13 Paise Set

24 Supply & installing of Utiity bench machine for Shoulder of

jerai or equivelant Size - 1060 mm x 680 mm x 900 mm

make made from standard make complete as per detail Rupees Twenty Nine

specification and instruction of consultant. Thousand One Hundred

1.00 29100.63 and Sixty Three Paise Set

25 Supply & installing of Back extension machine for Shoulder

of jerai or equivelant Size - 1270 mm x 990 mm x 1630 Rupees Thirty Eight

mm make made from standard make complete as per Thousand Four Hundred

detail specification and instruction of consultant. Twelve and Eighty Three

1.00 38412.83 Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

26 Supply & installing of Pressure curl machine for Shoulder of

jerai or equivelant Size - 1270 mm x 990 mm x 1630 mm Rupees Forty Seven

make made from standard make complete as per detail Thousand Seven Hundred

specification and instruction of consultant. Twenty Five and Three

1.00 47725.03 Paise Set

27 Supplying of Fitness accessories like dumbell MS high

quality nickel chome plated sets as following size & sets

with dumbell standard make complete as per detail Rupees Two Hundred

specification and instruction of consultant. Twenty One and Sixteen

740.00 221.16 Paise Kg

28 Supplying of Fitness accessories like Plates MS high quality

nickel chome plated sets as following size & sets with

dumbell standard make complete as per detail specification Rupees Two Hundred

and instruction of consultant. Fifteen and Thirty Four

455.00 215.34 Paise Kg

29 Supplying of Fitness accessories like Rods MS high quality

nickel chome plated sets as following size & sets with

dumbell standard make complete as per detail specification Rupees Nine Hundred

and instruction of consultant. Eighty Nine and Forty Two

44.00 989.42 Paise Feet

30 Supplying of Fitness accessories like EZ Rods MS high

quality nickel chome plated sets as following size & sets

with dumbell standard make complete as per detail Rupees One Thousand

specification and instruction of consultant. One Hundred Five and

8.00 1105.82 Eighty Two Paise Feet

31 Supply & installing of Power Rack of jerai or equivelant Rupees One Lac Four

make made from standard make complete as per detail Thousand Seven Hundred

specification and instruction of consultant. Sixty Two and Twenty

1.00 104762.25 Five Paise Kg

32 Supply of Fix barbell and rack set each set contain 2 stand

of jerai Or equivelant make made from 20 to 40mm dia Rupees One Lac Sixty Two

round CRCA power coated pipe with silicon/rubber slew Thousand Nine Hundred

complete. Sixty Three and Fifty

1.00 162963.50 Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

33 Supply of Doumble rack set each set contain 2 stand Size -

214 x 70 / 76 x 44 cm of jerai Or equivelant make made

from standard make complete as per detail specification and Rupees Fifty One

instruction of consultant. Thousand Two Hundred

2.00 51217.10 Seventeen and Ten Paise Set

34 Supply of Plate tree each of jerai Or equivelant make made Rupees Thirty Four

from standard make complete as per detail specification and Thousand Nine Hundred

instruction of consultant. Twenty and Seventy Five

1.00 34920.75 Paise Set

35 Supply of Flate Olympic GS 24 each of jerai Or equivelant

Size - 1740 mm x 1700 mm x 1250 mm made standard Rupees Sixty Two

make complete as per detail specification and instruction of Thousand Eight Hundred

consultant. Fifty Seven and Thirty

1.00 62857.35 Five Paise Set

36 Supply of Decline Olympic each of jerai Or equivelant Size -

1740 mm x 1700 mm x 1250 mm standard make complete Rupees Sixty Eight

as per detail specification and instruction of consultant. Thousand Six Hundred

Seventy Seven and Forty

1.00 68677.48 Eight Paise Set

37 Supply of Incline Olympic each of jerai Or equivelant Size -

1740 mm x 1700 mm x 1250 mm standard make complete Rupees Eighty Seven

as per detail specification and instruction of consultant. Thousand Three Hundred

One and Eighty Eight

1.00 87301.88 Paise Set

38 Supply of Prone leg each of jerai Or equivelant Thick -

mm, weight - 100 kg, N.W. - 211 kg and G.W. - 242 kg Rupees One Lac Seventy

standard make complete as per detail specification and Four Thousand Six

instruction of consultant. Hundred Three and

1.00 174603.75 Seventy Five Paise Set

39 Supply of Web board each of jerai Or equivelant standard Rupees Fifty Two

make complete as per detail specification and instruction of Thousand Three Hundred

consultant. Eighty One and Thirteen

1.00 52381.13 Paise Set

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

40 Supply of coloured Yoga mats of standard makes as specify

colour made from Thermoplastic elastomer. Which is more

enviornment friendly or made from eco conscious Jute

intermixed with a thin rubber layer for floor grip. The mates Rupees Seven Hundred

should be free from harmful substances. Fifty Six and Sixty Two

10.00 756.62 Paise No.

41 Supplying and Installation of Revolving Low Back Chair-

Upholstered with Leatherette seat have be made up of

12mm+/-1 mm thick hot pressed Mr grad plywood on which

moulded PU foam mounted. Back is made up moulded PU

foam and Inner outer snap fitted covers injection moulded

rectangular shape.The mechanism of the chair have

following features: 360⁰ revolving push back Mechanism,

Tilt tension adjustable, Single position locking, Overall

dimensions of Chair-Width of Chair-580 mm,Depth of chair-

580 mm as measured from base below. Height of back from Rupees Four Thousand

ground-min 950 to max 1050 mm. Seat height -min 440 Three Hundred Thirty

5.00 mm to max 540 mm. 4338.46 Eight and Forty Six Paise No.

42 Supplying and Installation of Revolving High Back Chair

Premium: High Back Rev. Chair - Upholstered with

Leatherette seat made up of 12 mm+ /- 1 mm thick hot

pressed Mr grad plywood and back in two Pieces 12 mm

inner Back and 6 mm in Rear Back. Moulded polyurethane

foam used in making seat with moulded density 45+/-2

Rupees Twenty One

kg/m³. Back is made out of 32 Density Block Foam covered

Thousand Nine Hundred

with 14 mm thick 32 density foam sheet (Block foam).

Ninety Seven and Eighty

2.00 21997.80 Paise No.

43 Providing and Supplying and Installtion of Indian Teak

(Sag) Wood Three Seater Sofa of as per given design, Rupees Forty Seven

details and instructions of Engineer-in-charge or Interior Thousand Nine Hundred

Designer and all complete. Fifty Five and Twenty

3.00 47955.20 Paise No.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

44 Providing and Supplying and Installtion of Indian Teak

(Sag) Wood Table of as per given design, details and Rupees Twenty One

instructions of Engineer-in-charge or Interior Designer and Thousand Nine Hundred

all complete. Ninety Seven and Eighty

1.00 21997.80 Paise No.

45 Providing and Supplying Locker all Complete as per

Engineer in Charge Instruction. Rupees Seventy Three

Thousand Three Hundred

2.00 73326.00 Twenty Six Only No.

CHORWAD NAGARPALIKA

CHORWAD, DIST. JUNAGADH

Name of Project : PROPOSED GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

Name of Work : ELECTRIFICATION WORK FOR GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

SCHEDULE - "B3"

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

1 Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to

10 mtr length, in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/

Wooden box, single mounting base frame covered with

textured/ metallic/ white front plate modules erected on/

in wall/ ceiling as per pipe erected, with necessary Lamp

holder/ ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories Rupees Four Hundred

erected concealed in wall/ ceiling complete Cat. III Eighty Five and Eighty One

53.00 485.81 Paise Pt.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

2 Point wiring for FAN with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A Modular

type switch and hum free EME step type electronic fan

regulator mounted and accessories with earth continuity

of following type erected on PVC/ Metallic/ Wooden box,

single mounting base frame covered with textured/

metallic/ white front plate modules erected on / in wall

/ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories Rupees Six Hundred

erected concealed in wall/ ceiling complete Cat. III Seventy Four and Sixty

14.00 674.68 Eight Paise Pt.

3 Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC/

Metallic/ Wooden box covered with appropriate front

plate modules erected on/ in wall/ ceiling as per pipe

erected with following type of accessories.

[I] For 6A Plug and 6a switch with 2-1.5 sq.mm Cu.

Wire from nearby switchboard/ mcb db board (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ ceiling complete Cat. III Rupees Five Hundred Ten

11.00 510.05 and Five Paise Pt.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

4 Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/ Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories.

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm

Cu. Wire from mcb db board.

(f) with medium class Rigid PVC pipe and accessories Rupees Seven Hundred

erected concealed in wall/ceiling complete Cat. III Forty Five and Thirty Eight

11.00 745.38 Paise Pt.

5 Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/ Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories.

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm

Cu. Wire with 2.5 sq.mm (green) earthing wire from mcb

(f) with medium class Rigid PVC pipe and accessories Rupees Eight Hundred

erected concealed in wall/ceiling complete Cat. III Seventy One and Sixty

3.00 871.63 Three Paise Pt.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

6 Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC/ Metallic/

Wooden box, single mounting base frame covered with

textured/ metallic/ white front plate modules erected on/

in wall/ ceiling with following type accessories Cat.-III

Rupees Two Hundred Fifty

12.00 257.55 Seven and Fifty Five Paise Pt.

7 Providing following type of Modular Type Accessories

mounted with PVC / metallic/ Wooden box, single

mounting base frame covered with textured/ metallic/

white front plate, modules erected with necessary

connections as per site situation directed by Engineer In

(14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular

Rupees Four Hundred Ten

MCB Switch Cat.III

1.00 410.06 and Six Paise Ea.

8 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /

flushed on wall/ ceiling, with 1.5 sq.mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories (b) 2 wire

Rupees Eighty Two and

260.00 82.82 Eighty Two Paise Mtr.

9 Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (e)

Sq.mm 3 core round PVC sheathed Rupees Forty Six and Forty

147.00 46.46 Six Paise Mtr.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

10 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/

name 160V to 270V, Power Factor more than 0.95, THD

< 15%, CCT 3000K to 6500K, Luminaire efficacy >

lumens/watt, LED driver efficiency > 85% (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings. The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (i) 5-10 Watts, Surge-

2 KV, IP-20, conventional 1 to 2 feet Cat-lll Rupees One Hundred Sixty

6.00 165.64 Five and Sixty Four Paise Ea.

11 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95,

THD < 15%, CCT 3000K to 6500K, Luminaire efficacy >

85 lumens/watt, LED driver efficiency > 85 % (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings. The Engineer incharge may select any

wattage capacity between the ranges shown.)

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

(A) Tube Light with integral driver (v) 36-40 Watts, Rupees Five Hundred

Surge-2 KV, IP-20, conventional 4 feet Cat-lll Thirty Five and Thirty

21.00 535.30 Paise Ea.

12 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/ CRCA/

aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name 160V

to 270V, Power Factor more than 0.95, THD < 15 %, CCT

3000K to 6500K, Luminaire efficacy > 85 lumens/watt,

LED driver efficiency > 85 % (fitting required LM-79 & LM-

80 Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The Engineer

incharge may select any wattage capacity between the

(A) Square/ Circular shaped Surface/ Recessed Mount

Downlight with provision for spring loaded mounting clips Rupees Two Hundred

complete. IP20 (i) 5-9 watts, Surge-2 KV Cat-lll Twenty and Eighteen

4.00 220.18 Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

13 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/ CRCA/

aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name 160V

to 270V, Power Factor more than 0.95, THD < 15 %, CCT

3000K to 6500K, Luminaire efficacy > 85 lumens/watt,

LED driver efficiency > 85 % (fitting required LM-79 & LM-

80 Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The Engineer

incharge may select any wattage capacity between the

(B) LED Panel Light with provision for Plane front frame Rupees One Thousand

with translucent cover fixed to housing complete.IP20 Seven Hundred Ninety

(vi) 36 watts, 24" x 24", Surge- 2KV Cat-lll Four and Seventy Seven

15.00 1794.77 Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

14 Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

270V, Power Factor more than 0.95, THD < 10%, CCT

3000K to 5700K, Uniformity ratio > 0.45, Luminaire

efficacy > 100 lumens/watt. LED driver efficiency >

%. (fittings required LM-79 & LM-80 certificates) (NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings. The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection-4KV integral Rupees Four Thousand

and, Light must have 440VAC line supply with over- Nine Hundred Ninety

voltage protection. (ii) above 48 to 60 Watts Cat-lll Seven and Forty Eight

21.00 4997.48 Paise Ea.

15 Providing Approved make Triple Pole Metal Clad Switch

Fuse Unit 415/500V. with HRC fuse of suitable load and Rupees Five Thousand

neutral link confirming to IS. (c) 100 A/125 A Cat.III Eight Hundred Twelve and

1.00 5812.55 Fifty Five Paise Ea.

16 Erection & connection charges for 32A/ 63A/ 100A HRC

TPN as following (b) Erection on New angle iron frame Rupees One Hundred

duly painted with red oxide Thirty Eight and Thirty

1.00 138.37 Seven Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

17 Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415V, having normal current rating up

to 25A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected

Rupees Six Thousand One

in existing 16 G.M.S. housing. ICS=100% of ICU only Cat

Hundred Seventy Three

1.00 6173.12 and Twelve Paise Ea.

18 Supplying and erecting triple pole & neutral 440V / 500V

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

Rupees One Thousand

necessary connections. (A) Suitable for 100 Amp.

Nine Hundred Sixty One

0.50 1961.42 and Forty Two Paise Rn.Mtr

19 providing and erecting Miniature circuit breaker single

pole 6A to 25A suitable to operate on 240V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

Cat.III Rupees One Hundred

39.00 112.11 Twelve and Eleven Paise Ea.

20 Providing & erecting 415V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS:8828 in existing box having following Rupees Five Hundred

capacity (a) 6 to 32 Amp. Cat.III Ninety Five and Ninety

5.00 595.90 Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

21 Providing & erecting 415V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS:8828 in existing box having following Rupees Seven Hundred

capacity (c) 63 Amp. Cat.III Thirty Seven and Thirty

1.00 737.30 Paise Ea.

22 Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs. (The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type

Rupees Three Thousand

outgoing Per phase isolation type (PPI) (b) sheet steel

Four Hundred Twelve and

double door (iii) 8 way

1.00 3412.79 Seventy Nine Paise Ea.

23 providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240V, 50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

Rupees One Thousand

component. for following Max. rating erected as directed

Nine Hundred Sixty Nine

(i) 25 Amps.DP Cat. III

3.00 1969.50 and Fifty Paise Ea.

24 Providing and erecting Approved make RCCBs

conforming to IS:12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral 415V,

50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any

Rupees Two Thousand Six

electronic component for following Max. rating erected as

Hundred Thirty Seven and

directed. (ii) 40Amps. FP Cat. III

2.00 2637.11 Eleven Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

25 Providing and erecting metallic vitrified danger notice

board as per language suggested by engineer incharge

for MEDIUM VOLTAGE installation to be erected as per IS-

2551. Rupees Sixty Nine and

2.00 69.69 Sixty Nine Paise Ea.

26 Providing and erecting Annealed bare Copper wire 8 to Rupees Seven Hundred

16 SWG. Ninety Four and Eighty

5.00 794.87 Seven Paise Kg.

27 Providing and erecting Pipe type earthing having

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit Rupees Three Hundred

complete with necessary 8 SWG earth wire. Sixty Eight and Sixty Five

12.00 368.65 Paise Ea.

28 For using salt and charcoal / coke as required for pipe Rupees One Hundred

type earthing. Seventy One and Seventy

12.00 171.70 Paise Ea.

29 Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I. Pipes having

Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with chamber

and heavy duty cover.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

(A) (approved make OEM has to submit test certificate

including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has

to ensure the value of earthing resistane mentioned in

test Certificate) & having back filling compound of

(B) Inner chemical (CCM Compound)- Resistivity:-

ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:-

<2% (C) Back fill Compound:- Earthing compound

should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.

(c) For Electrical Installation covering Transformer

Neutrals, Lightning arrester Earthing, A.C. Plant &

Sensitive Computer System (like Automation, SCADA) i.e

independent Earthing in normal soil. Length of Pipe: 3.00 Rupees Eight Thousand Six

mtrs Back filling Compound: 2 nos Bags of 25 Kg. Hundred Thirty Six and

2.00 8636.51 Fifty One Paise Ea.

30 Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated outdoor type double door

cubical panel board necessary IP-54 and above

protection as per approval from engineer incharge made

from 14 SWG thick CRC M.S. sheet for outer body &

doors, 16 SWG thick CRC M.S.sheet for internal partitions

with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding,

riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire/ copper-aluminium strips,

rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and

rubber gasket, heavy duty end terminal connection,

danger notice board, necessary ventilation, earthing strip

complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with

following approved manufacturers with following size. (A)

Rupees Eleven Thousand

locally fabricated panel board (i) with 350 mm depth

Four Hundred Sixty Six

1.00 11466.53 and Fifty Three Paise Sq.Mtr

31 Providing and erecting XLPE (IS:7098) (I)-88 ISI

armoured cable multistrand / Solid Copper conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench/ pipe at road crossing or floor of following Rupees Three Hundred

size of cables. (B) 4 core 4 Sq. mm Sixty Four and Sixty One

195.00 364.61 Paise Mtr.

32 Providing and erecting XLPE(IS:7098) (I)-88 ISI

armoured cable multistrand/ Solid Copper conductor for

1.1KV. to be laid on wall with necessary clamps or in

existing trench/ pipe at road crossing or floor of following

size of cables. (C) 4 core 6 Sq.mm Rupees Five Hundred Ten

5.00 510.05 and Five Paise Mtr.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

33 Providing and erecting XLPE (IS:7098) (I)-88 ISI

armoured cable multistrand Copper conductor for 1.1KV.

to be laid on wall with necessary clamps or in existing

trench/ pipe at road crossing or floor of following size of Rupees Nine Hundred

cables. (B) 4 core 16 Sq. mm Eighty Seven and Seventy

5.00 987.78 Eight Paise Mtr.

34 Making trench in soft soil of suitable width of 90 cm deep

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

ground. Rupees Fifty Five and Fifty

140.00 55.55 Five Paise Mtr.

35 Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene (conforming to

IS 14930 II) with necessary connecting accessories of

same material at required depth in existing trench for

laying of cable. below ground/ road surface for enclosing

cable (A) 50 mm outer dia Rupees Sixty Two and

170.00 62.62 Sixty Two Paise Mtr.

36 Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (A) 2 to 4 core 2.5 / 4 Sq.mm

Rupees Thirty Three and

24.00 33.33 Thirty Three Paise Ea.

37 Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (D) 2 to 4 core 16 Sq. mm Rupees Forty Seven and

2.00 47.47 Forty Seven Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

38 Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/2.5 to 6 Sq.mm Rupees Eight and Eight

96.00 8.08 Paise Ea.

39 Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (C) 16 Sq.mm. Rupees Twelve and Twelve

8.00 12.12 Paise Ea.

40 Supply, Installation, Testing and Commissioning of

suitable sweep, BEE 5 Star rated, Ceiling fan with Brush

Less Direct Current (BLDC) permanent ferrite magnet

Motor, class of insulation: B, Rust free 3 nos.Aluminium

blades, 2 nos. canopies, shackle kit with earthing

provision, copper winding, Power factor not < 0.9,

Service Value (CMM/W) minimum 6.85,

Air delivery minimum 215 CMM, 350 RPM,230v

(tolerance as per IS : 374-2019), THD < 10%, with

remote unit for Speed Control and all remaining

accessories including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable for

to 285 Voltage and rectifier circuit with surge, over

current and overload protection, 50 Hz, Single phase AC

Supply, earthing etc. Complete as required. [Make shall

be approved by Engineer in Charge] (B) 1200 mm Sweep

Rupees Two Thousand

Eight Hundred Eighty Five

14.00 2885.57 and Fifty Seven Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

41 Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each

side and pierced through a 16 Gauge M.S. box / Heavy

Duty PVC box complete erected concealed in Ceiling with

necessary finishing. Rupees One Hundred Eight

14.00 108.07 and Seven Paise Ea.

42 Providing 2.5mm.thick laminated acrylic sheet to cover

the fan hook or Fan box. Rupees Eighteen and

14.00 18.18 Eighteen Paise Ea.

43 Supplying & erecting single phase approved make

industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium duty

having following dia size and maximum speed in RPM [A]

305 mm dia 900 RPM Cat.II Rupees Two Thousand Fifty

7.00 2054.34 Four and Thirty Four Paise Ea

44 Providing suitable M.S. louver shutter of the Exhaust fan. Rupees Three Hundred

Sixty Eight and Sixty Five

7.00 368.65 Paise Ea.

45 Supplying & erecting electro galvanised G.I. wire micro

mesh jali cover of grade 304 required size with suitable

wooden frame duly fitted in wall outside of exhaust fan Rupees Six Hundred Thirty

for insect protection. Four and Twenty Eight

7.00 634.28 Paise Sq. Mtr

46 Providing recess in wall or window frame suitable for

erection of Exhaust fan complete with plastering and

colour washing to match the colour of the wall or window

complete with expanded metal in order to render the

fitting in accessible and the room water-proof. Rupees One Hundred

Eighty Nine and Eighty

7.00 189.88 Eight Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

47 Supply of approved make FRP Pole having following

specifications: FRP Light Pole made by CNC filament

winding machine using thermoset resin polyester/epoxy

resin system) having minimum 62% glass content. The

pole should be in one piece and tapered round in shape,

having smooth finish and should be totally free from

corrosion as well as non conductive & shock proof Pole

should be provided with FRP Anchor Base and it should

be heavy duty, or MS Material duly painted with Epoxy

Pole should be flame retardant as per IS 6746. Resin

used shall be UV resistance and pigmented. A highly

weather resistant polyurethane coating shall be applied

to the pole after applying suitable primer system that

ensures proper adhesion of the paint. Minimum coating

thickness shall be 80 to 100 micron. Deflection of the

pole shall not exceed more than 10% of the length of

pole for the given load“ Pole should be generally made as

per the dimensional data, performance criteria and some

interchangeability features of poles as per standard ANSI

C 136.20 latest version or ASTM D 4923/01 including

cable termination box with necessary accessories . The

size of pole and type of installation with foundation as

per manufacturer details and site requirement are as

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx.

Weight of Pole 32 kg approx. (Without Base) Anchor Base

(Size 300X300 & 18mm Th.) Rupees Fourteen Thousand

Fifty Nine and Twenty

7.00 14059.20 Paise Ea

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

48 Supply of approved make FRP Pole having following

specifications: FRP Light Pole made by CNC filament

winding machine using thermoset resin polyester/epoxy

resin system) having minimum 62% glass content. The

pole should be in one piece and tapered round in shape,

having smooth finish and should be totally free from

corrosion as well as non conductive & shock proof Pole

should be provided with FRP Anchor Base and it should

be heavy duty, or MS Material duly painted with Epoxy

Pole should be flame retardant as per IS 6746. Resin

used shall be UV resistance and pigmented. A highly

weather resistant polyurethane coating shall be applied

to the pole after applying suitable primer system that

ensures proper adhesion of the paint. Minimum coating

thickness shall be 80 to 100 micron. Deflection of the

pole shall not exceed more than 10% of the length of

pole for the given load“ Pole should be generally made as

per the dimensional data, performance criteria and some

interchangeability features of poles as per standard ANSI

C 136.20 latest version or ASTM D 4923/01 including

cable termination box with necessary accessories. The

size of pole and type of installation with foundation as

per manufacturer details and site requirement are as

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

(1) Suitable for base plate mounting single arm Bracket.

[C] Overall length of 3.5 Mtr. Average Thickness: 7mm.

Top/ Bottom OD Dia A/F 89/135 mm ± 2mm approx.

Approx. Weight of Pole 15kg. approx. (Without Base)

Anchor Base (Size 250X250 & 12mm th.) Rupees Nine Thousand

Twenty Three and Thirty

5.00 9023.34 Four Paise Ea

49 Providing FRP arm bracket of having 2 sets of suitable

SS304 hardware for fixing the brackets & spread of

Mtr (Suitable for 89 to 114 mm pole top dia) (A) Single Rupees Two Thousand Five

arm bracket Hundred Fifty One and

7.00 2551.26 Twenty Six Paise Ea

50 Providing FRP arm bracket of having 2 sets of suitable

SS304 hardware for fixing the brackets & spread of

Mtr (Suitable for 89 to 114 mm pole top dia) (B) Double Rupees Three Thousand

arm bracket Nine Hundred Thirty Three

1.00 3933.95 and Ninety Five Paise Ea

51 Providing FRP arm bracket of having 2 sets of suitable

SS304 hardware for fixing the brackets & spread of

Mtr (Suitable for 89 to 114 mm pole top dia) (C) Triple Rupees Five Thousand

arm bracket Three Hundred Eleven and

4.00 5311.59 Fifty Nine Paise Ea

52 Supplying & erecting approved make time switch with

single pole air break contacts suitable for 230V. 15/16A.

complete with self starting motor driven clock ‘ON’ &’

OFF’ automatic arrangement at any predetermined time

during each 24 hours,With nickel cadmium rechargeable

Rupees Two Thousand

battery backup erected as directed.

Three Hundred Fifty Four

2.00 2354.31 and Thirty One Paise Ea.

53 Supplying & erecting power contactor, AC3 duty for time

switch complete erected as per direction Cat III (D) 4 Rupees Two Thousand

pole 440V 40 Amp. Seven Hundred Eighty Two

2.00 2782.55 and Fifty Five Paise Ea

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

54 Providing and erecting Inverter based approved make

split air-conditioning unit consisting of condensing unit

with variable speed fan motor, inverter type hermetically

sealed rotary compressor with accessories etc. duly

connected separately erected evaporating unit and

blower motor with its accessories by means of extra

supplied proper insulated copper tubing,drain PVC pipes

suitable for (cost includes Eco Friendly green gas

charging and 15A plug top & Remote Control & MS

Stand) with necessary core cutting. (2) For ISEER Range Rupees Fifty Five Thousand

(KWH/KWH) (4.0 to 4.49) (B) for 1.5 ton capacity- One Hundred Eighty Nine

1.00 Premium Cat. 55189.43 and Forty Three Paise Ea.

55 Providing & Erecting full SS Body (SS 304) Split type

water cooler having storage capacity 160 to 175 Ltr.

(Tank SS 304) & Cooling capacity 150 ltr. Per hour @ an

ambient temp of 350C. The outlet temp. of the water

should drop by 150C within a hour,The water cooler

should be comprising of hermetically sealed

Reciprocating compressor with R134A, fan motor, Copper

Condensing unit with company fabricated Outdoor Unit

water tank surrounded by evaporating coil, thermostats,

relay etc. complete with necessary copper tube &

Insulation, M.S Chanel Stand with Painting for water tank

& M.S. Powder Coated Stand for Outdoor unit with

Installation. With DPELCB and 4 Way DB Box with Rupees Sixty One

accessory Three core Cord for connection. Thousand One Hundred

1.00 61115.10 Fifteen and Ten Paise Ea.

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

56 Supplying & erecting reverse osmosis (RO) water

purification system with M.S. powder coated pedestal

frame, prefilter housing carbon filter suitable buster DC

pump, auto low & high pressure switches with following

size of LPH capacity & erected as directed [E] 200 LPH

with 1 phase/ 3 phase Raw water pump of 1000LPH @

2.5kg/cm2 (1N0 - Kirloskar/ CRI/ Lubi), Dual media filter

10"x54" (1 No), Micron catridge filter 20" x 2.5" - (1No),

High pressure pump 1000LPH @ 10kg/cm2 - (1No -

Shimge /CRI /Lubi), RO Membrane housing with RO Rupees Ninety Three

membrane of 40*40 - (1 No), RO pressure tube 4" x 1E- Thousand Four Hundred

(1No), 0-1200LPH Rotameter- (2 Nos). Recovery Rate Sixty Eight and Forty Three

57 Supplying and erecting Direct on line starter with

Amp. (resistive @ 230v) power relay and with 2 to 5/

to 10 / 8 to 20 amp. Range C.T. Operated electronic

overload relay in engineering grade plastic enclosure for

3 ph 415v 50 HZ A.C. motor up to 7.5 HP with high

voltage protection (above 480 v) and under voltage

protection (below 330 v) current sensing single phasing

protection. Reverse phasing protection, inverse current

characteristic overload protection with indication for On,

OL, HV,LV SPP in a single unit with feather touch start /

stop push button, high temperature with standing Rupees Two Thousand One

Bakelite terminals complete erected on P.W. Block with Hundred Sixty Eight and

2.00 necessary connection. [Cat.II] 2168.47 Forty Seven Paise Ea

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

58 Providing & erecting open well horizontal mono block

pump set with cast iron body, complete for three phase

submersible motor having [D] For 5 HP 3 phase open

well horizontal mono block pump set suitable for

LPM to 310 LPM @ 10 to 42 Mtr head suitable for 50/65 Rupees Eighteen Thousand

mm dia delivery pipe Cat.II Seven Hundred Forty Six

1.00 18746.61 and Sixty One Paise Ea.

59 Supplying & erecting approved make Automatic liquid

level controller 6A. with sensor testing as per instruction

of Engineer in charge on site complete with wiring

connection with existing wires, with copper conductor

from pump to upper and lower tank. Rupees Two Thousand

Three Hundred Fifty Five

2.00 2355.32 and Thirty Two Paise Ea.

60 S.I.T.C. submersible pump set suitable for bore of

mm. dia. or more having three phase motor capacity not

more than 5 H.P. with following capacity . Lifting and

Lowering taken extra. (A) (25 stage) 120 to 125 LPM Rupees Twenty Six

discharge at 155 to 120 mtrs. head respectively suitable Thousand Eight Hundred

for 50 mm dia. delivery pipe Cat.III Ninety Four and Twenty

1.00 26894.28 Eight Paise Ea.

61 Lowering of submersible motor pump set at the depth of

following, complete with required. Nos. and size of casing

pipes erected by means of proper chain pulley block &

pipe wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe

Rupees Two Thousand Five

assembly filled up with water (B) Above 60 mtrs. and Up

Hundred Sixty Eight and

1.00 2568.43 Forty Three Paise Per Job

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated in Figure in Words according to

but may be estimated

more or less quantities.

62 Lowering of submersible motor pump set at the depth of

following, complete with required. Nos. and size of casing

pipes erected by means of proper chain pulley block &

pipe wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe

assembly filled up with water (D) For Open well

Horizontal submersible pump set for sump well (i) 1 HP

Rupees Eight Hundred Fifty

1.00 856.48 Six and Forty Eight Paise Per Job

63 Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq.mm

Rupees One Hundred Forty

150.00 146.45 Six and Forty Five Paise Mtr.

CHORWAD NAGARPALIKA

CHORWAD, DIST. JUNAGADH

Name of Project : PROPOSED GYM & FITNESS CENTER AT CHORVAD, DIST. JUNAGADH

Salvagable Material

Item Quantities Item Description Estimated Rates Unit Total Amount

Item Quantities Item Description Estimated Rates Unit Total Amount

No. Estimated according to

in Figure in Words

but may be estimated

more or less quantities.

1 Bela Stone (Salvaged, old) Rupees Twenty Two and

6270.00 22.09 Nine Paise Nos.

2 Steel (Salvaged, old)

11685.00 16.00 Rupees Sixteen Only Kg

3 Paver Block (Salvaged, old) Rupees One Hundred

Eighty Eight and Fifty Six

230.45 188.56 Paise Sqm