SPECIAL REPAIR TO BULIDING NO. P-38 IN ASC TYPE A AND BATHROOM PORTION ONLY IN BUILDING NO. P-82 SECTOR D AT MIL STN YOL.

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance exceeding 1.5 Km but not exceeding 2.00 Km complete all as specified and directed.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance exceeding 1.5 Km but not exceeding 2.00 Kmm complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance exceeding 1.5 Km but not exceeding 2.00 Kmm complete all as specified and directed.

Demolition of brick work or stonework or precast concrete articles and precast concrete block walling ,built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distanceexceeding 1.5 Km but not exceeding 2.00 Kmm complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Dismantling plain or corrugated steel sheeting any guage, thickness including Nainital or similar pattern roof covering, all as specified.

Taking down chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed.

Demolition of factory made PVC cubicial partitian , complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, and disposal of unserviceable material, debris and rubbish to a distanceexceeding 1.5 Km but not exceeding 2.00 Kmm complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises. complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Demolition and breaking up 75mm/110 bore drain pipe (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down steel rolling shutter of any descripton exc 2 sqm each and removing from site, complete all as specified.

Taking down existing unserviceable roof treatment on roof slab , taking down cement plaster including existing tarfelt from roof to of old roof surfaces by brushing with wire brushes for removing caked mud etc, sweeping with broom and finally fanning the cleaned surface to romove all loose dirt etc. on roof etc. and disposal of rubbish n.exc 50m distance from the starting point, complete all as specified and as directed by Engr-In-Charge.

Broken bats Aggregate for loose filling, for sunken floor slab, gauge 80 mm to 150 mm graded, complete all as specified.

Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering, complete all as specified.

PCC 1:5:10 (nominal mix) type E-2 (using 40mm graded crushed stone aggregates) as in filling and mass concrete in sunken floor complete all as specified and directed.

PCC 1:3:6(nominal mix) type C-1 (using 20mm graded crushed stone aggregates) as in filling concrete for hold fast, complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork where required complete all as specified and directed.

RCC Type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete flat, complete all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 (01 cement : 06 coarse sand) all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, as in half brick thick wall ,any radius, built in cement mortar 1:4 and pointed with same mortar as the work proceeds complete all as specified and directed.

2nd class hardwood (Sal) plain solid straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 105 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

35mm thick , Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on one side and other face is covered with decorative face veneer with lipping/frame to match sides , fitted to chowkhats complete all as specified and directed.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. Make : As per Appendix 'C'. Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Mild steel butt hinges of size 75mm medium weight cold rolled complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 75mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 100 mm and fixed complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

Continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap 40mm (when opened), complete all as specified.

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified.

Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

18/19mm thick, Prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination, fixed with screws to timber frame work complete all as specified and directed.

External teak wood lipping, 6mm thick fixed with nails, suitable for 18/19mm thick prelaminated particle board, complete all as specified.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification & drawing as shown on page No 176 to 183 of MES SSR 2020 Part-II compete all as specified and directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification & drawing as shown on page No 176 to 183 of MES SSR 2020 Part-II compete all as specified and directed.

Aluminium anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding and also including 4mm thick, Non asbestos fibre cement building boards fixed or laid/ inserted to framework with screws, as in ceiling , complete all as specified. Note : The board shall be as per IS-14862 and shall be manufactured from homogeneous mixture of cement, quartz and cellulose and shall be cured with high pressure steam using auto claving process.all as specified and directed.

Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Rolled mild steel work in Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc., conforming to Fe-410- W(Gde- E-250) quality- A, complete all as specified and as directed.

Rolled mild steel work in Rolled sections as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410- W(Gde- E-250) quality- B, complete all as specified and as directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Steel rolling shutters, without ball bearing, including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete (Thickness of laths 1.00 mm): gear operated type with bevel gear box and crank handle, complete all as specified.

Safety lever locks mild steel with 4 levers for rolling shutters, complete all as specified.

75mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed.

50mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregates) as in padding in floors , finished even and smooth, without using extra cement, complete all as specified and directed. .

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) for sunken portion complete all as specified and directed.

Non-Skid,Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7-8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. Note : Size,Shade and colour of tiles shall be approved by GE.

Glazed ceramic coloured tiles of size 450 mm x 300 mm x 7 mm/350 mm x 250 mm x 7 mm / 1200x600x7mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Note : Size,Shade and Colour of tile shall be approved by the GE.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified.

20mm thick Granite slab (table rubbed, edges rounded & polished on both sides)) as in urinal partitian with chase cutter & embedded the stone in the chase with epoxy grout chemical (like araldite etc) or with cement mortar 1:4 , complete all as specified and directed. Note : Size, shade and colour shall be approved by GE

Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 15 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, trowelled to even and smooth finish without using extra cement with water proofing compound complete all as specified. Note : Supply Only water proofing compound shall be measured and paid seperately

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, trowelled to even and smooth finish without using extra cement complete all as specified.

5mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling , chajjas, fin, facias etc and including applying cement slurry; surface finished even & smooth without using extra cement complete all as specified and directed .

Supply only intergal water proofing compound, complete all as specified.

Water proofing treatment over terrace using SHALIURETHANE- BTD OF STP MAKE OR EQUIVALENT as approved by GE, high solid content single component water based liquid applied elastomeric water proofing membrane as ASTMC 836 and ASTMD 6083, thickness of the membrane shall be 1.50mm, having solid content of more than 80% elongation of 500+(-) 50%, laid over reinforcing layer on non woven geo-textile mesh of 40/50, 50 gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and surface preparation complete as per manufacturer's instructions complete all as specified and directed

Taking down cement plaster/decayed concrete from RCC roof projections/upward parapet walls/down facia/soffits and fins of RCC chajjas/beams/columns/balconies etc. and also applying one coat of anti corrision paint to visible reinforcement if any. Supply and fixing by means of nailing wire netting of galvanised wire 1.40mm dia and mesh size 20mm and brushing neat cement slury with 3.00 Kg of cement/sqm including 20mm thick cement rendering in two layers of 10mm each using shot gun or pressure nozzle for grouting the surface well bonded with reinforcement (top/final layer shall be rendered after final setting of under layer) in CM 1:3 on concrete surfaces including scaffolding at a height upto 7.00 mtrs etc complete all as specified and directed.

Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint over one coat of primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceilings and applying two coat of oil bound distemper over a coat of primer , finished smooth with sand paper complete all as specified and directed.

Taking down old cement plaster of walls and perform waterproofing of exterior walls, including raking out joints,loose particles complete and applying two coats of acrylic polymer modified high performance coating . The treatment shall be done from ground level and upto suitable height as directed and icluding 15mm thick cement plaster in CM 1:4 well finished even and smooth complete all as sepcified and directed. Make : Asian/ Berger/ Nerolac

20mm bore, CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

16mm bore, CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Steel tubes, 32 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, as in spout of sunken floor/ overflow pipe , including taking down old pipe complete all as specified and directed.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified

Chromium plated soap dish, fixed to plugs wirh chromium plated brass screws ,fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, with pedestal, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including , 15mm bore cast copper alloy, with capstan heads, chromium plated, fancy type mixer, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx

Vitreous China bowl urinal full stall type, white (including fixing bolts, flush pipe, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 7.0 litres), with grating and union for discharge pipe, flush pipe and waste pipe, , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, PVC connections 450mm long, 15mm size with brass couplings nuts including grating and Union for discharge pipe, complete all as specified and as directed.

Stop valves/ angle valve , cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. Note : Type of valve to be approved by the GE.

Bath and shower mixer 3 in 1 for mixing hot and cold water with arrangement for both telephonic hand shower and overhead shower with bend pipe with connecting legs and wall flanges, screwed down or iron pipe, 15mm bore and fixed, and fixed in repairs complete, all as specified. Make : Cera Cat Part No. F2014403 or equivalent in Jaquar/Hindware/Paryag

Flush valve concealed push type (single flush) 32 mm (1.25”), chromium plated suitable for 15mm bore of pipe, and fixed in repairs complete, all as specified. Make : Cera Cat Part No. F8010103 or equivalent in makes mentioned in Appx 'C'.

Bib tap, cast copper alloy ,chromium plated, fancy type , Bib cock long nose with wall flange and aerator , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair complete all as specified and directed. Make : Cera Cat Part No. F2002152 or equivalent in Jaquar/Hindware/Paryag

Pillar taps, with 310 mm (12.5”) long extended body and aerator , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, of 15 mm bore, fixed in repair complete all as specified and directed. Make : Cera Cat Part No. F1016102 or equivalent in Jaquar/Hindware/Paryag

PVC connections 15 mm size with PTMT nuts of length 600mm fixed in repair complete all as specified and directed.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified.

32mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight - 45gms), fixed in repair , complete all as specified.

32mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight - 45gms), suitable for urinals, fixed in repair , complete all as specified.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), fixed in repair , complete all as specified.

32mm bore, Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm, complete all as specified.

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. S1053101 for EWC, B1510123 for seat cover, of 'Cera' or equivalent in makes mentioned in Appx 'C'

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, snow white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc and making good to floors to match existing, in repairs, all as specified. Make: Cat Part No.S3020105 of 'Cera' or equivalent makes mentioned in Appx 'C'.

PVC valve less, snow white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No. B1010112 of Cera or equivalent in makes mentioned in Appx 'C'.

5.5mm thick , Bevelled edge polished mirror of slected quality glass ( Size not less than 2.8 Sqm), mounted mounted on walls with spacers with CP brass screws and cup washers , fixed in repair , complete all as specified.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor ,complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor , complete all as specified and directed.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints,fixed to walls , complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints,fixed to walls , complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified.

110 mm dia PVC(SWR) vent cowl complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 250 Lires but but not exceeding 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc, complete all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including taking down old tank any typecomplete all as specified.

Factory casted of 12 mm High Pressure Laminated (HPL) sheet certified to IS-2046 for toilet and shower room partition with approved design and shade by Engr-in-Charge comprising of good quality and high pressure resistance with proper resistance from scratch, abrasion, heat, chemical, impact and moisture resistance alongwith anti-bacterial resistance. Note : HPL sheet should be of approved make with a suitable warranty period.

Factory made STAINLESS STEEL HARDWARE SET comprising of :- (i) Spring loaded auto closed hinges 3PC (SS 304)- (ii) Coat Hook Cum Door stopper 1 PC (SS 304)- (iii) Look cum privacy indicator 1 PC (SS-304)- (iv) Round Door Knob 1 Pair (SS 304)- (v) Adjustable Leg height 120mm to 150mm 2PC (SS 316)- (vi) Screw- Rubber and all accessories reqd to make cubicle partition. Note : The hardware quality, size and grade shall be approved by Engineer-in-Charge and of stainless steel grade of certified warranty. Make : SUPERFIT/ GODREJ/ HITACHI

Stainless Steel finish chromium plated top rail of suitable length having section 50x 32 mm or other size to receive 12 mm thk HPL sheet well fitted and make proper finish with the help of screws, adhesives supported by walls or clamps, completed all as specified and as directed.

Stainless Steel Finish chromium plated U Shaped rail of suitable length having section 25 mm x 16 mm or other size to receive 12 mm thick HPL sheet well fitted and make proper finish with the help of screw, adhesives supported by walls or clamps , completed all as specified and as directed.

Stainless Steel Finish Anodize Chromium plated door stopper / H type channel section of suitable length having section 20 mm x 12.5 mm or other to receive 12 mm thk HPL sheet well fitted and make proper finish with the help of screws, adhesives supported by walls or clamps, completed all as specified and as directed.

Stainless Steel Finish chromium plated 90’ section or F Channel section or other for corners of suitable length having section 20 mm x 12.5 mm or other to receive 12 mm thk HPL sheet well fitted and make proper finish with the help of screws, adhesives supported by walls or clamps, completed all as specified and as directed

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surface complete all as specified and directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC concealed (concealed wiring) conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring, cutting chases, making good in cement mortar in CM (1:3), finishing surfaces to match with existing and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly for modular fitting, modular box sunk for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '119' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '119' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '119' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Modular switch 1 way 6A, 1 module, complete all as specified.

Modular switch 1 way 16A, 1 module, complete all as specified.

Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified.

Modular Socket 6A/16A - 2/3 pin combined , 2 module, all as specified and directed.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 12 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack , 10 watt LED,6500k, two feet long, with all acessoreis internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Make: Havell's Cat Part No. LHEXACP7IN1W010 of "Havells" or equivalent in makes mentioned in Appendix

LED type tube light, 1x20 watt 230 volts wall mounted Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours, internely pre wired and including connecting up with three core twisted flexible copper conductor cable of suitable size. Make: Havells cat part No. LHEXACP7FN1W020 or equivalent in Appx

LED Luminaire 600mmx600mm, 36 watt, 6500K, Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling, complete all as specified Make: Havells cat part No. LHEBAEP7IW1W036 or equivalent in Appx

50 Watt Street Light with best in class design & Robust heat sink along with class leading IP, IK & Surge protections for long lasting performance. with IP65 protection and impact resistance of IK08. connecting with PVC insulated three core flexible copper conductor of suitable size to fitting including bracket made up of 32mm dia GI pipe light grade 1.5 metre long and bent to shape required, complete all as specified Make: Havells cat part No. LHEXBAP7PN7J050 or equivalent in Appx

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, B Curve all as specified.

MCB SPN 40 to 63 Amp, 240 Volts, 10 KA , B curve all as specified.

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm, including taking down old fan, complete all as specified.

Taking down wall mounted fan 400mm sweep any make from existing position from any height by disconnecting electric connection and inspection of exhaust fan in presence of JE incharge(or rep of department) after dismantalling spare parts. including hanging fixing and connecting up and testing etc complete all as required at site and directed by Engr-in-charge

Complete repair and maintenance of unserviciable wall mounted fan 400mm sweep including dismentalling complete fan parts i,connections inspecting serviciability of all the parts refixing of serviciable parts after cleaning and replacement of unserviciable parts with companies with genuine parts i.e capacitor,bearing,bushes,shaft(rubber bush connecting wire PVC connector aluminium clamps for rod bush rods blades) and greasing oiling etc including repaint assembling cleaning and testing of fan as directed.

Removing of old burnt winding any type cleaning stator complete for burnt wiring carbon residue and rewinding of stator winding of any type any make fan any stator design wall mounted fan of any sweep with superior quality super enemaled winding copper wire of existing specifications guage and weight with superior quality insulation of satisfactory functioning inpresence of JE incharge complete all as directed by Engr-in-charge

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 31 of tender doucments.

MM Constructions (BID ID -3343073)

Eshaan Construction Co. (BID ID -3343134)