SPL REPAIR TO OFFR MD ACCN NEAR TCP GATE NO 2 AT BIRPUR AND PROVN OF LT PANEL AND ALLIED ELECTRIC WORK AT DSOM AND I UNDER GE DEHRADUN.

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Material and labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, using old size bricks, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:6, surface finished even and smooth (without using extra cement) complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, surface finished even and smooth (without using extra cement) complete all as specified and directed.

Material and labour for 10 mm thick rendering on ceiling surface in cement mortar 1:3 mixed surface finished even and smooth including fixing of wire mesh wherever required complete all as specified and directed.

Material and labour for preparation of newly plastered surface of walls including corners and applying two coats of distemper oil emulsion over applying of 1-2 mm thick wall care putty finish wall surface even & smooth complete all as specified and directed.

Material and labour for complete removal of existing treatment of walls including corners and applying two coats of distemper oil emulsion over applying of 1-2 mm thick wall care putty finish wall surface even & smooth all complete all as specified and directed.

Material and labour for two coats of exterior grade 1st quality weather coat paints over a coat of alkali resistant priming paint over applying of 1-2 mm thick wall care putty finish wall surface even and smooth including preparation of new plaster external surfaces of wall etc with scrap wire brush and washing with water complete all as specified and directed.

Material and labour for complete removal of existing treatment of walls including corners and applying two coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over applying of 1-2 mm thick wall care putty finish wall surface even and smooth complete all as specified and directed.

Material and labour for preparation of newly plastered surface of ceilings and applying two coats of distemper oil emulsion on ceiling, off sets, pillar etc.complete all as specified and directed.

Material and labour for preparation of old plastered surface on ceilings and applying two coats of distemper oil emulsion on ceiling, off sets, pillar etc complete all as specified and directed.

Material and labour writing letters or figures (Block. Roman, Italic or Indian) nexc 30 cm high Writing bldg No complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

Material and labour for vitrified ceramic tiles light shade 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over and including screed bed15 mm thick in CM 1:6 set and jointed in neat cement slurry @ 3kg per sqm and pointed in white or coloured cement to match with tile including dismantling of existing tiling complete all as specified and directed.

Description all as per item No 16 above but as in skirting over and including 10 mm thick rendering in cement mortar 1:4 complete all as directed and specified and directed.

Material and labour for non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x 7 to 8 mm thick in floor, set and jointed in neat cement slurry @ 3kg per sqm and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Description all as per item No 18 above but as in skirting over and including 10 mm thick rendering in cement mortar 1:4, complete all as directed and specified and directed.

Material and labour for non skid/mat finish ceramic colour tiles of size 300 mm x 300 mm and 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry @ 3 kg per sqm and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for glazed ceramic colour tiles size 300 mm x 450 mm/ 300 mm x 600mm x 7 to 8 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry @ 3 kg per sqm and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as directed and specified.

Dismantling of stone slabs and tiles laid, bedded in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Material and labour for 18-20 mm thick Granite, of any type, table rubbed and polished in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified including moulding complete all as specified and directed.

Taking down chowkhats or frames with shutters n.exc 1.50 sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames with shutters exc 1.50 sqm but n.exc 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Supply and fix factory made 100 % solid wood plastic composite (WPC) door frame 125x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed.

Supply and fix factory made 100 % solid wood plastic composite (WPC) door frame 105x60 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed.

Supply and fix 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side plain with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and directed.

Supply and fix 30 mm thick moulded WPC factory made Glazed and skeleton shutter (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side plain with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and directed.

Supply and fix Stainless steel Butt Hinges medium weight, cold rolled 100 mm fixed to steel/wooden/WPC shutters complete all as specified and directed.

Supply and fix Stainless steel barrel tower bolts 150 mm size, with bright bolt fixed in repairs complete all as specified and directed.

Supply and fix 150 mm size solid in one piece stainless steel handles, cast D type, fixed with stainless steel screws complete all as specified and directed.

Supply and fix 300 mm long Stainless steel Helical door spring welded to steel frame or fixed to wooden door frame with screws including roller and roller plate etc complete all as specified and directed.

Supply and fix floor door stopper of stainless steel double legged and tongue, 304 grade, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

Supply and fix stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and directed.

Supply & fix for powder coated Aluminium standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one nos wire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows, and glazed with glass 5mm thick, fixed with glazing clips, aluminium grill with mesh size 75 mm and aluminium bar 6 mm XPM type, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc, complete all as specified and directed. Shutter Top & bottom size:- 37.50 x 15.00 x 1.60 mm Shutter inner lock size:- 37.50 x 15.00 x 1.60 mm Shutter side (Handle) size:- 37.50 x 15.00 x 1.36 mm Chowkhat bottom size:- 50.30 x 26.00 x 1.20 mm Chowkhat top & sides size:- 50.30 x 26.00 x 1.00 mm Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco (ii) Particle board: Century ply/ Kitply / Green ply (iii) Glass: Saint gobain / Modi guard / Tata Note: Iron grill with frame to be fixed with window (measured and paid separately)

Supply and fix Stainless steel 304 grade wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with 8% nickle complete all as specified and directed.

Supply & fix in repair 18 mm thick PVC board one side prelaminated and other side plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive complete all as specified and directed.

Supply & fix in repair 18 mm thick PVC board both side plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive complete all as specified and directed.

Supply & fix in repair 6 mm thick PVC board both side plain white colour as in cub board selves etc fixed with screws, salvent cement/ adhessive , complete all as per specifications and directed.

Supply and fix 75 mm size solid one piece stainless steel handles, cast D type, fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

Supply and fix Continuous (Piano) hinges, mild steel, bright finished or stainless steel 304 grade, width of flaps (When open) 30 mm complete all as specified and directed.

Supply and fix magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

Supply & fix in repair chrome plated stainless steel wire basket (storage basket) pull out type for large utensils of size 480 x 500 x 150 mm of grade 304 with necessary fixing clips etc. complete all as specified and as directed.

Supply & fix in repair chrome plated stainless steel wire basket (plate basket) pull out type for large utensils of size 380 x 500 x 100 mm of grade 304 with necessary fixing clips etc. complete all as specified and as directed.

Supply & fix in repair chrome plated stainless steel wire basket (cutlery basket) pull out type for large utensils of size 380 x 500 x 100 mm of grade 304 with necessary fixing clips etc. complete all as specified and as directed.

Supply & fix in repair chrome plated stainless steel wire basket (grain trolly basket) pull out type for large utensils of size 480 x 500 x 100 mm of grade 304 with necessary fixing clips etc. complete all as specified and as directed.

Supply & fix Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs , complete all as specified and directed.

Supply & fix in repair 25 mm dia stainless steel polished 204 grade drapery rod 1mm thick with final decorative, including brackets, decorative finished at both ends complete all as speccified and directed as per approved sample complete all as specified and directed.

Supply & fix medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing including dismantling of old tubing complete all as specified and directed.

Supply & fix medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing including dismantling of old tubing complete all as specified and directed.

Supply & fix in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and directed.

Supply & fix in repairs vitreous china water closet (Padestal pattern) single sheet fancy type including fixing bolts, flushing cistern dual flush type of total capacity 10 ltr incl PVC white Seat cover and incl lime concrete bedding including 100mm CI 'P' or 'S' trap complete all as directed.

Supply & fix in repair 10 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve with PVC long bend for out let, fixing with WC complete all as specified and directed.

Supply & fix in repair vitreous china wash hand basin including Pedestral, white size 550 x 400 mm including cutting for and pinning in ends of brackets, including Waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed.

Supply & fix in repair sink mixer 15 mm dia, Brass Chromium plated complete all as specified and directed.

Supply & fix in repair wall mixer/L bend mixer 15 mm dia, Brass Chromium plated complete all as specified and directed.

Supply & fix in repairs centre hole basin mixer 15 mm dia, Brass Chromium plated complete all as specified and directed.

Supply & fix CP brass bib tap long body 15mm bore screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix in repairs CP stop/angle cock fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fix in repair CP brass shower rose,100mm dia and suitable for 15 mm dia pipe, complete all as specified and directed.

Supply and fix in repairs PVC connection 15mm size with PTMT nuts, of 450 mm long complete all as specified and directed.

Supply and fix in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix in repairs Soap dish 6 inches, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Supply and fix in repairs health faucet mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix in repair waste coupling 32mm dia PTMT half or full threaded for sink etc, complete all as specified and directed.

Supply and fix in repair CP steel Grating round with steel frame with hinge 100mm dia complete all as specified and directed.

Supply and fix in repairs 32mm bore heavy duty waste pipe not less than 80cm long with PVC coupler for kitchen sink, WHB, urinal, etc complete all as specified and directed.

Supply & fix in repair glass corner shelf suitable size made of 5 mm thick toughened glass with CP railing complete all as specified.

Supply & fix in repair front glass shelf assembly consisting of 5.5 mm thick toughened glass with CP railing and brass brackets of size 500x125 mm, complete all as specified.

Supply and fix in repairs stainless steel kitchen sink without draining board ISI marked made of stainless steel 1 mm thick, with plugs, washers and wastes, including bedding lime cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 410mm x 330mm x 160mm,complete all as specified and directed.

Taking down CI/AC/PVC pipes incl fittings upto 110mm dia and removing from site complete all as specified and directed.

Supply and fix PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls or laid in trenches or floors complete all as specified and directed.

Supply and fix PVC (SWR) pipes of 75 mm dia, single socketed fixed to walls or laid in trenches or floors complete all as specified and directed.

Supply and fix PVC (SWR) bends of 110 mm dia, any radius complete all as specified and directed.

Supply and fix PVC (SWR) bends of 75 mm dia, any radius complete all as specified and directed.

Supply and fix PVC (SWR) junction single Tee equal or unequal 110 mm dia complete all as specified and directed.

Supply and fix PVC (SWR) junction single Tee equal or unequal 75 mm dia complete all as specified and directed.

Supply and fix PVC nahani trap of 75mm bore, with grating including jointing to waste pipe with solvent fixed in cement concrete type B1 (1:2:4), complete all as specified and directed.

Supply and fix in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed.

Supply and fix in repairs for 110mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement and demolition of existing old cement concrete of plinth protection in ground floor and paving below or above ground level complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

Material and labour for 20-25 mm thick machine cut Kota stone slab as in flooring/skirting over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding,mirror polished to exposed edges incl 20 mm thick screed bedding layer of CM 1:4 complete all as specified and directed.

Supply and fix rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external and internal white and fly nut complete screwed down for iron pipe of 20 mm dia including dismantling of old tank complete all as specified and directed.

Supply and fix rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external and internal white and fly nut complete screwed down for iron pipe of 20 mm dia including dismantling of old tank complete all as specified and directed.

Supply and fix in repairs Gun metal gate valve iron wheel head screwed both ends for iron pipe of 20 mm bore complete all as specified and directed.

Taking out & removing existing roof treatment of any description completely upto concrete surface including racking out joints, hacking for key, sweeping clean and scrubbing down with water etc to remove dust etc,complete all as specified and directed.

Material & labour for surface preparation of roof and treating of joints, filling of honey combs and providing 25 mm thick PCC (1:2:4) type B-0 with WPC over roof surface complete all as specified and directed.

Material and labour for Water proofing roof treatment with polymeric water proofing membranes of weight not less than 3Kg/sqm five layers with center core as 90 micron high molesuvre,high density polythene film sand witched between two layers of polymeric (Static polythene based) between laminated on both sides with 20 micron HMDPF film over a coat of hot blown bitumen with 85/25 grade @ 1.20 Kg/Sqm after priming the surface with bituminous emulsion @ 0.30 Litre/Sqm on plastered surface. Water proofing membrane should be laid with over laps 150 mm at ends and 75 mm for sides and shall be bounded uniformity by LPG torch flame over the polymeric water proofing membranes apply semi hot blown bitumen 85/25 grade @ 1.20 Kg/ sqm dusted sand over the coat of the coat @0.5 Kg/Sqm and applying aluminium reflective paint over it as per manufacturers instructions complete all as specified and directed. Note : - The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. (ii) 2.5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. Contractor's quoted rate for this item shall deemed to be inclusive of this aspect.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply & fix MS rolled sections / tubular pipes etc. as in main and cross beams, Jack rafters, balconies and railings, purlins where connected to common rafters and running rails etc confirming to Fe-290(Grade E-165) , complete all as specified and directed.

Supply and fixing framed work such as grills, gratings, etc. or hand rails with ends of bars (angle, hollow section) shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings etc, complete all as specified and directed.

Supply and fix for prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for 60 mm thick pre polished rubber moulded coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and as directed.

Material and labour for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed.

Material and labour for sand filling 25mm thick under floors or in foundations including watering and consolidation complete all as specified and as directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, removing surplus soil to a distance n exc 50m and making good surface in hard/dense soil complete all as specified and as directed.

Material and labour PCC (1:3:6) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed.

Supply and fix mild steel work as in post and strut in fencing including cutting tops to shape as directed drilling holes, notching for wire etc. and flat iron fillets, 10 mm dia round bar, nut & bolts for securing wire mesh including all necessary drilling and bolting including embeding in concrete and similar work confirming to Fe-290 Gde E-165 including dismantling of posts of any type, complete all as specified and directed.

Supply only chain link MS galvanised fencing any mesh, size & type of standard as approved by Engineer-in-Charge.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wire any size or type complete all as specified and dirceted

Dismantling fencing wire mesh, any type complete all as specified and directed.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole cable etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and directed.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete) 150mm bore set in cement mortar complete all as specified and directed.

Supply and fix 150 mm Salt glazed stoneware drain pipes, grade ‘A’ complete all as specified and diirected as per Eng-in-charge.

Material and labour for PCC (1:3:6) type C-2 (using 20 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

Material and labour for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with suitable size modular cover plate , one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge for following :-

One light point/ ceiling fan point/ Exhaust fan point controlled by one-one way switch

One bell point controlled by one-one way switch bell push.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board.

Description all as per item No 113 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor cable of size 2.5 Sq mm complete all as specified and directed.

Description all as per item No 113 above but up to Sheet matel enclosure MCB DB with plug socket independent, with cable 4 Sq mm size, with earth continuity coductor cable of size 4 Sq mm complete all as specified and directed.

Supply and fix modular switch 1 way 6A,1 module,230 volts complete all as specified and directed.

Supply and fix modular switch 1 way 16A,1 module, 230 volts complete all as specified and directed.

Supply and fix modular socket 6A-2/3 pin, 2 module, 230 volts complete all as specified and directed.

Supply and fix modular socket combination 6/16 A,6 pin,2 module ,230 volts complete all as specified and directed.

Supply and fix modular fan step regulator, 120W,2 module ,230 volts complete all as specified and directed.

Supply and fix Modular Bell push 6A 1 module complete all as specified and directed.

Supply and fix Bell Multi Music type complete all as specified and directed.

Supply and fix in replacement of sheet metal enclosure SPN with 3 pin earth metal plug and socket complete with one SPN MCB 20 Amps, 240 volts in repairs complete all as specified and directed by Engineer-in-Charge.

Supply and fix ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 220 V AC complete all as specified and directed.

Material and labour lamp holder insulated body with back plate suitable for angle and batten fitting including LED bulb 9 watt complete all as specified.

Material and labour sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multistranded of size 10 Sq.mm. (nominal area) drawing in and including 25 mm. dia or higher PVC concealed conduit heavy duty accessories and fittings. PVC insulated unsheathed FRLS cable copper conductor multistranded of size 10 Sq. mm. as earth wire upto common earth and connected to earth dolly including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed. NOTE : - 3 run of cable and 1 run of conduit shall be measured as 1 unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories/fittings.

Supply and fix sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going including connection with suitable size copper lugs/thimbles/glands including taking down existing unserviciable DBs including MCBs complete all as specified and directed

Supply and fix sheet metal enclosures Triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing including connection with suitable size copper lugs/thimbles/glands including taking down existing unserviciable DBs including MCBs complete all as specified and directed

Supply and fix MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked including connection with suitable size copper lugs complete all as specified and directed.

Supply and fix MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked including connection with suitable size copper lugs complete all as specified and directed.

Supply and fix MCCB 415 Volt 16 KA 4 pole 125 Amp adjustable type as incoming with fixing arrangement including connection with suitable size copper lugs complete all as specified and directed.

Supply and fix wall mounted LED tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Supply and fix mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Supply and fix LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Supply and fix ceiling fan 1200 mm sweep single phase 230 volts double ball bearing with down rod , canopy, blades etc ,BLDC TYPE, 5 star rated including connecting with twisted three cord flaxible copper conductor cable (23/.0076 ) from ceiling rose to connector of fan etc including taking down old ceiling fans and deposited to AGE EM-II store yard complete all as specified and directed.

Supply and fix exhaust fan, metallic body AC single Phase. 230V of size 300mm sweep RPM, single phase, 230V AC with louver all as specified and making hole for fixing arrangement on wall with frame holdfastner, bolt, washer etcincluding connection with twisted white three core flexible copper multistranded conductor cable from ceiling rose to connector all a directed. ( Note: Old unserviceable fan will be deposited in E/M store yard. )

Supply and fix in replacement air ventilation fan made of sturdy Engineering plastic complete with louvers shutter, 250 mm sweep, 1200 RPM, single phase, 230V AC including necessary and making hole for fixing arrangement on wall with frame holdfast, bolt, washer etc including connection with twisted white three core flexible copper multistranded conductor cabl from ceiling rose to connector all a directed by Engineer-in-charge. (Note: old unserviveable fan shall be deposite in E/M yard.)

Supply and fix in replacement of Geyser vertical mount type 25 Ltrs capacity BEE five star rated , shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall complete all as specified & directed . ( Note: old unserviceable Geyser will be deposited in E/ M store yard )

Supply and fix Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 240 Volts 20 amp single pole MCB complete all as specrified & directed

Material and labour GI bracket made out of 40 mm GI pipe medium grade pipe for fabrication to shape as required length of pipe 1.2 mtr with necessary fixing arrangement by means of MS clamps 02 Nos not less than 50x6 mm MS flat duly painted, nuts, bolts and washer complete all as specified & directed

Supply and fixing Integral LED Bldg security Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) and complete all as specified & directed. NOTE: (i) Earth lead strip and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

Supply and fix LED decorative post top lantern for Garden light 40 watt IP 65 protection resistance to impact and corrosion glare, free and better uniformity including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Supply, laying, jointing and testing of underground XLPE insulated, armouredheavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 Core laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs of cable size including taking down existing unserviceable cable etc complete all as specified and directed.

Description all as per Item No 144 but 6 Sq mm, 2 core complete all as specified & directed.

Supply, installation, testing and commissioning in replacement of L.T Panel, thermoplastic Polycarbonate IP 65 Distribution Board in accordance with IEC 60 529 (Dust Proof, Water Proof & Weatherproof) Thermoplastic Polycarbonate DB of Shock proof, Rust Proof, Corrosion Free, Acid & Chemical Resistant, Fire Retardant & Self Extinguishing, UV Resistant, Silica and Halogen Free recyclable material. Type tasted as per IEC 61 439-1. Total Insulated with System Voltage 415V AC, 50Hz, and 5 wires. The board/panel should be UV resistance in accordance with IEC 61439-1, clause 10.2.4:The panel should be anti-acid & anti corrosive. in accordance with IEC 62262.Outdoor Floor mounting with the following switch gears . Incomer:- MCCB 400 Amps 4P,35 KA - 01 Nos. Meter set : Digital voltmeter ,Ammeter + CT: 400/5, RYB indicating Lamp LED type 240 V,Rating of aluminium bus bar 600 Amp. Outgoing:- 250 Amp FP,36 KA MCCB- 01 Nos. 160 Amp FP,25 KA MCCB- 02 Nos. 125 Amp FP,25 KA MCCB- 01 Nos. 63 Amp FP,16 KA MCCB- 01 Nos

Material and labour , transporting, errecting and fixing in replacement Steel tubular swaged poles type 410 SP-31, 9.00 metre long , complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified including painting with two coats of synthetic enamalled paint over one coat of red oxide primer and 06 Nos bands/ straps with yellow and black colour ( 30 cm wide each)epoxy heat resistant paint at a distance 30 cm from plinth block and numbering of poles with black synthetic enamel paint in 2.5 cm height including tarring/Bituminous paint one coat on steel surface embedded in concrete foundation complete all as specified and shown on drawings and directed.

Material and labour for PCC (1:4:8) type D-2 (using 40mm graded caushed stone aggregate) as in foundation of poles and stay etc including form work complete all as specified & directed.

Material and labour for PCC 1:3;6 type C-1 (using 20 mm crushed stone aggregate) as in coping of poles etc including form work complete all as specified and directed.

Supply and fix junction box made of glass fibre reinforced and transparent poly carbonate of size 126x228x111, KV PC 8104 with IP 65 protection including MCB SP, 6 Amps 1 No and suitable size clamps fixing for pole/in pcc foundation etc,including taking down the old one,all as specified and as directed.

Supply and laying XLPE insulated galvanised steel strip or wire armoured electric power UG cable with stranded aluminium conductor 1100 V grade of size 95 sqmm 3.5 core complete all as specified and directed.

Supply and laying XLPE insulated galvanised steel strip or wire armoured electric power UG cable with stranded aluminium conductor 1100 V grade of size 10 sqmm 4 core complete all as specified and directed.

Material and labour for sand cushioning to under ground cable, 8 cms thick before laying the cable and 15 cms thick after laying & stretching the cable in trenches, including hand punning and consolidating, complete all as specified & directed . Note:- For payment purpose punned thickness shall be measured.

Material and labour for bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified & directed.

Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including three core copper wire and PVC conduit to connection light to Junction box and thermal management in multiple optics complete with IP 65/66 protection completed as directed .

Supply and fix Street light TIMER control panel ,110 Amps,3 pole /230 Volt ,Digital time switch ,pole/wall mounting made out of 3.15mm CRCA sheet duly power coated with locking arrangement including internal wiring complete with bypass arrangements complete all as specified and directed.

Material & Labour for Painting of poles 9 Mtr long with one coat of aluminium paint complete including fittings such as brackets etc. and black&white synthetic enamel paint on alternative strips upto height of 1.5mtr from copping of the pole including numbering the pole with 8cm size letter with back paint having back ground of yellow painted circle of 10cm dia complete all as directed.

Material and labour for earthing complete with galvanised earth plate electrode 600x600x6.0mm thick, buried directly in ground (Earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.50 mtr below normal ground level connected with galvanised iron earth strip 25x4mm by means of bolts, nuts, check nuts and washer of galvanised iron or steel complete with 40 mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15 type B1 in pit with angle iron (25x25x3)mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, test piont etc. in and including light frade GI protection pipe 40mm bore up to 7.5m lenght for drawing in earth lead wire , all as shown in electrical plate No.3 of SSR Part-1 complete with necessary earth work in any type of soil, removal to a distance not exc. 50m, testing on completion complete all as specified and directed. NOTE: (i) Earth lead strip and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

Supply and fix tubing 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

NOTE:- Amount of credit of Rs. 86112.00 for retrieved materials is mentioned in Schedule of Credit Page No 36 & 37 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s Pradeep Kumar (BID ID -3302819)

M/S SEWA AND SERVE BUILDERS (BID ID -3302943)