Tender for Comprehensive Operation and Maintenance contract of Street Light Poles, SITC of Street Light work at Eastern side and SITC and Implementation of Centralized Smart city Management System (CMS for streetlight) for entire Ahmedabad city for Five Years

Total Amount of 5 Years (SECTION-A)

Amount for 1st Year ( 1 month x 12 nos )

Amount for 2nd Year ( 1.03 x Amount of 1st Year )

Amount for 3rd Year ( 1.06 x Amount of 1st Year )

Amount for 4th Year ( 1.09 x Amount of 1st Year )

Amount for 5th Year ( 1.12 x Amount of 1st Year )

Total Amount of 5 Years (SECTION-B1)

Total Amount of 5 Years (SECTION-B1)

SECTION- B2 SITC Work

Amount of 1st Year

Amount of 2nd Year ( 1.03 x Amount of 1st Year )

Amount of 3rd Year ( 1.06 x Amount of 1st Year )

Amount of 4th Year ( 1.09 x Amount of 1st Year )

Amount of 5th Year ( 1.12 x Amount of 1st Year )

Total Amount of SITC Work (SECTION-B2)

Total Amount of SITC Work (SECTION-B2)

Total Amount of O & M (SECTION B1+ SECTION B2)

Total Amount of O & M (SECTION B1+ SECTION B2)

SECTION- C CMS and SFP Work

Implementation of City Management System ( for Street Light)

Section Feeder Pillar Work (Consider 50% New)

Section Feeder Pillar Upgradation Work (Consider Remaining 50% Upgradation Amount)

Total Amount of Section Feeder Pillar (SECTION-C)

Total Amount of Section Feeder Pillar (SECTION-C)

SECTION- D AI Work (Optional)

Total amount of AI Work (Section D) (Optional)

Total amount of AI Work (Section D) (Optional)

Document : Zone Wise pole qty detail

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

Sr NOS OF STREETLIGHT

5 Saijpur Bogha

8 Thakkarbapa Nagar

North Zone Total

3 Central Jamalpur

Central Zone Total

6 Ramol Hathijan

East Zone Total

South Zone Total

Grand Total ( Package A East Zone)

Grand Total ( Package A East Zone)

Document : SECTION-A, O & M WORK

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

DESCRIPTION UNIT

NO. QTY RATE TOTAL

Street Light pole with < = 30 w LED light fitting (With Single

Street Light pole with < = 30 w LED light fitting (With Two

Street Light pole with < = 30 w LED light fitting (With Three

Street Light pole with LED light fitting between 31w to 70 w

(With Single Arm)

Street Light pole with LED light fitting between 31w to 70 w

Street Light pole with LED light fitting between 31w to 70 w

(With Three Arm)

Street Light pole with LED light fitting between 31w to 70 w

(With Four Arm)

Street Light pole with LED light fitting between 71w to 135 w

& Above (With Single Arm)

Street Light pole with LED light fitting between 71w to 135 w

& Above (With Two Arm)

Street Light pole with LED light fitting between 71w to 135 w

& Above (With Three Arm)

Street Light pole with LED light fitting between 71w to 135 w

& Above (With Four Arm)

Street Light pole with SMART LED light fitting between 80w

to 250 w (Excluding LED Fixture, Driver, SPD, Smart

Controller, Over Voltage Protection Devices). (With Single

Street Light pole with SMART LED light fitting between 80w

13 to 250 w (Excluding LED Fixture, Driver, SPD, Smart No 588.00 105.00

Controller, Over Voltage Protection Devices) (With Two Arm)

Street Light pole with SMART LED light fitting between 80w

to 250 w (Excluding LED Fixture, Driver, SPD, Smart

Controller, Over Voltage Protection Devices) (With Three

Street Light pole with SMART LED light fitting between 80w

to 250 w (Including LED Fixture, Driver, SPD, Over Voltage

Protection Devices) (With Single Arm) (After guarantee

Street Light pole with SMART LED light fitting between 80w

to 250 w (Including LED Fixture, Driver, SPD, Over Voltage

Protection Devices) (With Two Arm) (After guarantee period

17 Ring Pole with Four Smart fitting No - 128.00 -

18 Ring Pole with Four fitting No - 128.00 -

19 High Mast Pole with LED fittings (12.0 mt to 30.0 mt High) No 161.00 1,801.00

High Mast Pole with Conventional (Sodium / MH) fittings

(12.0 mt to 30.0 mt High)

Monthly charges for the Provision of cellular / IoT data

connectivity for smart streetlight controllers and feeder-level

equipment, enabling real-time communication with the central

Document : SECTION-B1, OPTIONAL WORK FOR O&M

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

1 Section Feeder Panels

2 Cable Trench & Pipe

3 Cable & Termination

4 Street Light Pole & Bracket

Total Amount for 1 Year

Total Amount for 1 Year

Total Amount for 1 Month

Total Amount for 1 Month

ESTIMATE Page : 5 of

DESCRIPTION UNIT

NO. QTY RATE TOTAL

Note :It is mandatory for the successful bidder to execute this work as many times and for as much quantity as required,

based on the actual site conditions, throughout the entire contract period, as and when needed.

1 Section Feeder Pillar

Installation of Section Feeder Panel

Installation Testing and Comissioning of New / existing

section feeder pillar as said location by engineer in charge

complete in all respect as it is original with necessary cable

termination, with extra required various sizes cables & with

cable joints if needed etc. as per requirement or as per

instruction of engineer in charge.

Section Pillar Type-A, Each Door of Size Approx Height

1250mm, Length 450mm, 16 Guage

Section Pillar Type-B, Each Door of Size Approx Height

750mm, Length 375mm, 16 Guage

SITC of Section Pillar Stand of Size 40mm x 40mm x 6mm

angle, Height 950mm, Length 90mm, width 600mm.

Painting of Existing Section Feeder Panel Complete with two

coats of Aluminium Paint

1.6 Dismentalling of SFP no 275.00 1,108.00

1.7 Muffing of SFP no 225.00 4,209.00

Total of Section Feeder Pillar

2 Cable Trenches, Manholes & Pipes -

Making trench in soft soil of suitable width of 90 cms deep

from the final ground level or road level for laying cable or

locating the fault all over the run and backfilling the same &

clearing the site by removing debris & Shifting of the debris &

making site good As per the Instruction of the Engineer

Making trench in Hard murum / Tar Road of suitable width of

90 cms deep from the final ground level / road level for laying

cableor locating the fault all over the run and backfilling the

same and making the surface proper. by removing debris &

Shifting of the debris & making site good As per the

Instruction of the Engineer Incharge.

(B) If additional machinery like hammer driller or JCB use

Covering of cable with second class bricks laid cover the

cable crosswise & also on both sides with covering of 7.

Cms. layer of sand above & below cable (cable shall be laid

in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there are more

than one cable in the trench on either side of the cable,

Cms. over lapping of bricks shall be provided.

Driling the road without breaking the road surface (Asphalt)

for laying of cable for feeding power supply by making

Suitable size of holes at both ends complete. (A) Up to

Driling the road without breaking the road surface (Asphalt)

for laying of cable for feeding power supply by making

2.6 Suitable size of holes at both ends complete. mt 800.00 610.00

(B) Up to 150 mm bore dia

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type

with necessary connecting accessories of same material at

required depth for laying of cable. below ground / road

surface for enclosing cable with Excavation and backfilling the

same to make ground as per original. (A)50 mm dia

ESTIMATE Page : 6 of

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type

with necessary connecting accessories of same material at

required depth for laying of cable. below ground / road

surface for enclosing cable with Excavation and backfilling the

same to make ground as per original. (C)90 mm dia

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type

with necessary connecting accessories of same material at

required depth for laying of cable. below ground / road

surface for enclosing cable with Excavation and backfilling the

same to make ground as per original. (D)120 mm dia.

Providing & laying approved make ISI marked HDPE 6Kg /

cm2 (Class-3) as per IS:4984:1995 PE-80 to be erected at

2.10 road crossing on or floor as directed for laying of cable. The mt 22,000.00 487.00

pipes as following size of dia & weight per 6 mtr. (E) 90 mm

Providing & laying approved make ISI marked HDPE 6Kg /

cm2 (Class-3) as per IS:4984:1995 PE-80 to be erected at

2.11 road crossing on or floor as directed for laying of cable. The mt 22,000.00 725.00

pipes as following size of dia & weight per 6 mtr. (F) 110 mm

Total of Cable Trenches, Manholes & Pipes

SITC of Flexible PVC insulated multi strand multi core 1.1 kv

3.1 grade ISI marked copper wires of following size to be erected Mtr 1.00 46.00

as directed.(f) 1.50 Sq.mm 4 core round PVC sheathed

Supply and laying of XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables in Existing Cable Trench / Mtr 275.00 282.00

50 sq.mm x 3.5 c Al. cable

3.3 35 sq.mm x 3.5 c Al. cable Mtr 275.00 218.00

3.4 25 sq.mm x 4 c Al. cable Mtr 8,250.00 189.00

3.5 16 sq.mm x 4 c Al. cable Mtr 8,250.00 152.00

3.6 10 sq.mm x 4 c Al. cable Mtr 8,250.00 139.00

3.7 existing laid Cable recovery ( Per mtr Length ), Mtr 5,775.00 14.00

Disconnecting the cable connection and Providing straight

joint with PVC mould using heat shrink /cast resin type epoxy

compound Insulating material and making the joint complete

using necessary in line connectors, hardener, earth continuity

connection, spacers etc. and reconnecting the same & ensure

the joint resistance within the limits as per IS.

(A) up to 25 Sq mm Cable no. 11,065.00 1,073.00

(B) 35 to 95 Sq. mm cable. no. 1.00 1,535.00

3.9 Making of burnt Loop-IN, Loop-Out in poles no. 2,970.00 264.00

4 Street Light Pole -

Installation Testing & Commissioning up to 6 Mtr Tubuler

Pole/ Swaged Pole. with All kind of Accessories MCB,

Junction Box, Pole Numbering With 2 coat of Paint, Muffing,

stud type terminal and arrangement for cable termination as

per details given by manufacturer considering site

ESTIMATE Page : 7 of

Installation Testing & Commissioning up to 6 Mtr. Octagonal

pole/ Conical pole, any flanged mounted pole with All kind of

Accessories MCB, Junction Box, Pole Numbering With 2 coat

of Paint, stud type terminal and arrangement for cable

termination as per details given by manufacturer considering

site requirement.

Installation Testing & Commissioning up to 7 Mtr. to 10 Mtr.

Tubuler Pole/ Swaged Pole. with All kind of Accessories

MCB, Junction Box, Pole Numbering With 2 coat of Paint,

Muffing stud type terminal and arrangement for cable

termination as per details given by manufacturer considering

site requirement.

Installation Testing & Commissioning up to 7 Mtr.to 10 Mtr

Octagonal pole/ Conical pole, any flanged mounted pole with

All kind of Accessories MCB, Junction Box, Pole Numbering

With 2 coat of Paint, stud type terminal and arrangement for

cable termination as per details given by manufacturer

considering site requirement.

Installation Testing & Commissioning up to 11 Mtr. to

Mtr.Tubuler Pole/ Swaged Pole.with All kind of Accessories

MCB, Junction Box, Pole Numbering With 2 coat of Paint,

Muffing stud type terminal and arrangement for cable

termination as per details given by manufacturer considering

site requirement.

Installation Testing & Commissioning up to 11 Mtr.to 16 Mtr

Octagonal pole/ Conical Pole, any flanged mounted pole with

All kind of Accessories MCB, Junction Box, Pole Numbering

With 2 coat of Paint, stud type terminal and arrangement for

cable termination as per details given by manufacturer

considering site requirement.

Providing cement concrete.for foundation or for concrete

filling in 1:2:4 ratio with 20 to 25 mm stone metal duly

plastered with necessary curing for pole /Panel muffing or any

Providing TMT Bar FE 500/500D reinforcement for RCC work

4.8 including bending, binding and placing in position complete Kg. 13,750.00 75.46

upto floor two level.

SITC of 0.1 to 2 Mtr G.I.bracket with 2 coat P.U. Paint with

primer(Any Arm Bracket as per architect design).

Note : Sample must be Approved from Client / Architect /

Consultant before supply.

Painting of street light pole with bracket complete with two

4.1 coats of Aluminium paint for following size of pole. no 35.00 213.00

(A) up to 4 mtr

Painting of street light pole with bracket complete with two

4.11 coats of Aluminium paint for following size of pole. no 2,994.00 263.00

(B) up to 6 mtr.

Painting of street light pole with bracket complete with two

coats of Aluminium paint for following size of pole.

(C) up to 9 mtr

Painting of street light pole with bracket complete with two

4.13 coats of Aluminium paint for following size of pole. no 328.00 552.00

(D) up to 10 to 13 mtr / 16 mtr

4.14 PU base primer and PU Paint on pole up to 4.0 Mtr no 45.00 753.00

PU base primer and PU Paint on pole above 4.0 Mtr up to

PU base primer and PU Paint on pole above 8.0 Mtr up to

PU base primer and PU Paint on pole above 12.0 Mtr up to

SITC of Pole Numbering as per Engineer in charge, Charges

ESTIMATE Page : 8 of

Pole dismantling, carting and to submit at AMC store. ( 4 mtr

to 10 mtr height)

Pole dismantling, carting and to submit at AMC store. ( 10 mtr

to 16 mtr height) 12 NOS OF Foundation BOLT

Supply of Foundation bolt for 12 Mtr. To 30 Mtr. High Mast as

Any height and type pole alignment

Supply and Installation for Modification work of relocation of

Junction Box upto 1.2 Mtr. From bottom. Scope of work:- Hole

4.23 Drilling and Fixing of Junction box with loop in loop out cable no 544.00 941.00

in Existing GI / DWC Pipe with connection of Fixtures and

Supplying and erecting A class / B Class Galvanized iron pipe

having smooth finished bore of the pipe on both ends erected

nuts and bolts along the pole / wall shaping the pipe as per

site requirement. Pipe dia as following.

Supplying and erecting A class / B Class Galvanized iron pipe

having smooth finished bore of the pipe on both ends erected

4.25 nuts and bolts along the pole / wall shaping the pipe as per Mtr 1.00 323.00

site requirement. Pipe dia as following.

RCC/Asphalt road cutting to accommodate C-PVC 25 mm

heavy duty pipe minimum 2 x 2 inch (DXW) for cable laying

and reinstate with cementing in proper manner. (It also

include supply of C-PVC 25 mm heavy duty pipe & laying of

Note : It is mandatory in the scope of successful bidder to

execute this work as many times ( for as as many quantity) as

per actual site conditions during entire contract period as and

4.27 MS tubular sleeve 2 mtr long 219 mm dia extention piece no 68.00 6,690.00

Total of Street Light Pole

Chemical Type Earthing

Supplying & erecting in earthpit of minimum bore dia. 225mm

size , approved make Safe Earthing Electrode consisting

Pipe-in-Pipe Technology as per IS 3043-1987 made of

Copper Pipes having Outer pipe dia of 50mm having , Inner

pipe dia of 40 mm , connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

(a) For Electrical Installation up to 440V in normal soil Length

Back filling compound - 1 Nos Bag of 25 Kg.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I.

pipe with necessary coupling buch buried in specially

prepared earth pit & G.I. earth wire of 8 SWG erected &

connected as directed (For panel)

ESTIMATE Page : 9 of

Plate Type Earthing

Supplying & erecting funnel type earthing having earth plate

of following size burred in specifically prepared earth pit 3 mtr.

below ground with 40 kg. charcoal and salt with alternate

layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with

a wire mesh for watering & bricks masonry block, C.I. Cover

5.4 complete as per para 7.3 of IS 3043 with necessary length of Ea. 3.00 2,543.00

double Galvanised Iron / copper earth wire No 6 SWG bolted

with lug to the plate and covered in 12 mm dia. G.I. pipe

mtr long complete connected to the nearest switch gear with

end socket as per direction & duly tested by earth tester

confirming to IS (As per drawing) with following specification

With 45 x 45 x 0.35 cms. G.I. earth plate

Total of Earthing

6 Miscellanious -

Replacement of lightning arrestor as per actual site condition

during entire contractor period as and when required

Replacing of Head frame for 12 mtr. To 30 mtr. High mast

Replacing of Wire rope for 12 Mtr. To 30 Mtr. High Mast

Ligting System.

Replacement of Traveling cable for 12Mt. to 30 Mt. High Mast

Lighting System.

Replacement of Double winch drum for 12 Mtr. To 30 Mtr.

High Mast Lighting System

Rewinding of electrical motor for 12 Mtr. To 30 Mtr. High Mast

Lighting System.

Replacement of electrical motor for 12 Mtr. To 30 Mtr. High

Mast Lighting System.

Dismantling of 12Mt. to 30 Mt. High Mast Lighting System &

Carting to AMC store.

Installation of 12 Mtr. To 30 Mtr. High Mast Lighting System.

With loading / Unloading

Replacement of Lent ran carriage for 12 Mtr. To 30 Mtr. High

Mast Lighting System

To carry out census of existing street light poles, Post top

pole and feeder pillar (The same to be incorporated in eastern

side) in entire city with help of mobile app of any king of latest

6.11 equipment (Geo-coordinate mapping) depicting longitude and lot 1.00 5,00,000.00

latitude and code of each street light poles as per the formate

indicated in the tender

(To be complete within 3 months)

Total of Miscellanious

Reinstate of paver block with back filling. Waterring,PCC and

fixing blocks in proper manner.

SITC of Cement 1:5:10 (1 Cement: 5 Coarse sand: 10 hard

broken stone aggregates 40 mm nominal size) and curing

complete excluding cost of form work in (A) Foundation and

ESTIMATE Page : 10 of

Providing and Laying of Rubber Moulded Paver Block

Grey/Coloured 60 mm thick, M-35 Grade of any size ; shape

(Usually Uni-Paver Blocks) using black trap good quality

aggragate of 20 mm nominal size for footpath, parking areas,

service lanes and other areas as mentioned in the drawing /

instruction of engineer in charge. Cost includes formworks

using rubber mould, Rate providing and laying paver blocks

as per required grading and specification. The paver block

shall be echanically

7.3 compacted. The work of paving blocks shall be executed in Sq.Mtr. 173.00 475.00

line and level by skill mason of flooring work only. It should be

laid in such a way that the no cutting of the paver block to be

necessary. if cutting of paver

block necessary then it should be cut by machine only and

carting. The finished surface of the paver block shall have

resonably good, plain finished. Paver blocks shall be

compacted and shall be relaid if necessary. Gravel or such

type of materials shall not be allowed for production. Laying

on 5 cms thick sand

Total of Civil Work

ESTIMATE Page : 11 of

Document : SECTION-B2, SITC FOR Streetlight work

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

Description Amount

1 Section Feeder Panels

5 Cable & Termination

6 Street Light Pole & Bracket

7 Light Fixture

ESTIMATE Page : 12 of

DESCRIPTION UNIT

NO. QTY RATE TOTAL

Section Feeder Panels Type-C

"Supplying, unloading at site, shifting to site, assembling, leveling,

grouting, erecting, Testing, & Commissioning double

compartmentalized Street light control panel with IP 55 protection &

Enclosure should be powder coated fabricated from 12 Gauge M.S.

sheet & folded channel totally enclosed cubical type. with pad lock

arrangement. The successful tenderer will have to prepare general

arrangement with dimensions & get it approve through Architect/

Consultant. All civil work including RCC platform for street light panel

should be in scope of Electrical contractor complete in all respect as

per detail drawing and directed by engineer in charge. with the

mm height MS angle covered stand.

The switchboard (panel) shall have provision for future expansion &

shall be modular in construction. The bus bars shall be connected

with C type clamps without any drilling on the bus bars.

SITC of the IP 65 Smart Section feeder panel with space for Smart

Energy monitoring system and 2 number of 3 phase Energy meter of

Supply Company for the Street Lighting Consisting of following

Incoming : 100 Amp FP MCCB with the spreader link with in built

earth fault relay

R-Y-B-On-Off indicating Lamp with control fuse.

Set of 100 A. FP tinned copper busbars of EC. grade & adequate

capacity, size & insulated with colour tape & should be tined at all

Auto/Manual bypass switch with indicating lamp

Meter : VAF meter equivalent to Enercon make ELF 3259 with 100/

Outgoing : MCB's Should be of 10 KA.

Timer Equivalent to Theben make Astronomical type with the battery

back up : 2 nos.

40 amp. FP Power Contactor : 2 nos.

6 - 32 amp. DP Power Contactor : 8 nos.

40 Amp. FP MCB : 4 nos.

6 -32 Amp. FP MCB : 2 nos.

6 - 32 amp. SP MCB : 18 nos.

5 KVAR Capacitor with the 40 amp TP capacitor duty contactor with

the 10 minute time delay relay.

Panel Should Have lockable Space to incorporate the 2 nos of the

phase energy meter with its main switches with separate cable entry

with separate compartment & Separate door. Also door higes are

made from solid pin and bolted type. No welding are alloved for

Section Feeder Panels Type-D -

ESTIMATE Page : 13 of

Supplying, unloading at site, shifting to site, assembling, leveling,

grouting, erecting, Testing, & Commissioning double

compartmentalized Street light control panel with IP 55 protection &

Enclosure should be powder coated fabricated from 12 Gauge M.S.

sheet & folded channel totally enclosed cubical type. with pad lock

arrangement. The successful tenderer will have to prepare general

arrangement with dimensions & get it approve through Architect/

Consultant. All civil work including RCC platform for street light panel

should be in scope of Electrical contractor complete in all respect as

per detail drawing and directed by engineer in charge. with the

mm height MS angle covered stand.

The switchboard (panel) shall have provision for future expansion &

shall be modular in construction. The bus bars shall be connected

with C type clamps without any drilling on the bus bars.

SITC of the IP 65 Smart Section feeder panel with space for Smart

Energy monitoring system and 2 number of 3 phase Energy meter of

Supply Company for the Street Lighting Consisting of following

Incoming : 63 Amp FP MCB with the spreader link with in built earth

R-Y-B-On-Off indicating Lamp with control fuse.

Set of 63 A. FP tinned copper busbars of EC. grade & adequate

capacity, size & insulated with colour tape & should be tined at all

Auto/Manual bypass switch with indicating lamp

Meter : VAF meter equivalent to Enercon make ELF 3259 with 63/ 5 A

Outgoing : MCB's Should be of 10 KA.

Timer Equivalent to Theben make Astronomical type with the battery

back up : 2 nos.

40 amp. FP Power Contactor : 2 nos.

6 - 32 amp. DP Power Contactor : 8 nos.

40 Amp. FP MCB : 2 nos.

6 -32 Amp. FP MCB : 2 nos.

6 - 32 amp. SP MCB : 12 nos.

5 KVAR Capacitor with the 40 amp TP capacitor duty contactor with

the 10 minute time delay relay.

Panel Should Have lockable Space to incorporate the 2 nos of the

phase energy meter with its main switches with separate cable entry

with separate compartment & Separate door. Also door higes are

made from solid pin and bolted type. No welding are alloved for

ESTIMATE Page : 14 of

FEEDER SECTION PILLAR TYPE-A (Regular)

750 W x 600 L x 1050 H (As per drawing)

Supply, installation, Testing and commissioning of the Feeder Section

Pillars as per specifications, IS and Drawings

The unit rate for each item shall include : Call for final inspection prior

to dispatch. Delivery of the fidder pillar / section pillar to site. Shifting

of the fidder / section piller from site to store to the suitable location.

& Fixing of Section Pillar. Assembly and wiring of component supplied

separately. Installation of section

piller to including removing old section pillar. Earthing all components,

frame etc. to a common internal earth bar. M.S. parts should painted

with powder coating.

Supply & fixing all accessories and supporting structure. Supply & Set 72.00 49,161.00

fixing of M.S. 40 x 40 x 6 channels for fixing the panels. Connection,

testing and commissioning Checking of internal connection and

wiring, operation of switches, starter, MCCB, relays,

contactors etc. Supply of necessary tools, hardware, testing

equipment etc. etc. Electrical contractor shall carry out the insulation

test at site and all the readings shall be submitted in duplicate to the

consultant or engineer-in- charge.

All civil work including RCC platform for street light panel should be in

scope of Electrical contractor complete in all respect as per detail

drawing and directed by engineer in charge with the MS angle

covered stand. Approval from State Electricity Board & Liason work.

Also door higes are made from solid pin and bolted type. No welding

are alloved for hinges.

FEEDER SECTION PILLAR TYPE-B-1

SIZE :- 750 W x 600 L x 750 H (As per drawing)

Supply, installation, Testing and commissioning of the Feeder Section

Pillars as per specifications, IS and Drawings.

The unit rate for each item shall include : Call for final inspection prior

to dispatch. Delivery of the fidder pillar / section pillar to site. Shifting

of the fidder / section piller from site to store to the suitable location.

Shifting & Fixing of Section Pillar. Assembly and wiring of component

supplied separately. Installation of section piller to including old

section pillar. Earthing all components, frame etc. to a common

internal earth bar.M.S. Parts should painted with powder coating.

Supply & fixing all accessories and supporting structure. Supply & Set 45.00 30,602.00

fixing of M.S. 40 x 40 x 6 channels for fixing the panels. Connection,

testing and commissioning. Checking of internal connection and

wiring, operation of switches, starter, MCCB, relays, contactors

etc.Supply of neccessary tools, hardware, testing equipment etc.

Electrical contractor shall carry

out the insulation test at site and all the readings shall be submitted in

duplicate to the consultant or engineerin-

charge. All civil work including RCC platform for street light panel

should be in scope of Electrical contractor complete in all respect as

per detail drawing and directed by engineer in charge with the MS

angle covered stand. Approval from state Electricity Board & Liason

work.Also door higes are made from solid pin and bolted type. No

welding are alloved for hinges.

FEEDER SECTION PILLAR TYPE - B-2 Set 38.00 30,602.00

5 1200 W x 400 L x 900 H (As per drawing)

ESTIMATE Page : 15 of

FEEDER SECTION PILLAR TYPE - B-3

Size :- 600 x 600 x 250 mm

Supplying & erecting approved make IP 55 grade Company

fabricated Timer Panel of following capacity for switch On-Off

street lights on time scheduling basis made from 12 G CRCA

sheet duly epoxy power painted inside and outside with hinged

doors and locking arrangement consisting of suitable size of

Pole MCB and 4 pole contactor (cat-III)with Astronomical digital

time switch, auto manual switch of same make and suitable

input and output Bakelite terminals and with door earthing no 81.00 14,668.00

approved by Engineer in charge. Supply & fixing of M.S. 40 x

for fixing the panels. panel is also suitable to fit on wall. Also

door higes are made from solid pin and bolted type. No welding

are alloved for hinges. All civil work including RCC platform for

street light panel should be in scope of Electrical contractor

complete in all respect as per detail drawing and directed by

engineer in charge with the MS angle covered stand.

Removing of Section Feeder Panel

Dismantling and removing of existing section feeder pillar as said

location by engineer in charge complete in all respect as it is original

with necessary civil work foundation, cable termination, with extra

required various sizes cables & with cable joints if needed etc. as per

requirement or as per instruction of engineer in charge.

Installation of Section Feeder Panel

Installation Testing and Comissioning of New / existing section feeder

pillar as said location by engineer in charge complete in all respect as

it is original with necessary cable termination, with extra required

various sizes cables & with cable joints if needed etc. as per

requirement or as per instruction of engineer in charge.

Upgradation of Section Feeder Panel

Upgradation of existing section feeder pillar Install MCB instead of

Fuse as said location by engineer in charge complete in all respect as Set 5.00 3,000.00

it is original with necessary cable termination etc. as per requirement

or as per instruction of engineer in charge.

Total amount for Section Feeder Panels

Total amount for Section Feeder Panels

SITC of the MCB's ( 10 KA ) Timers , & Contactors With the Dinrail

Channel providing and erecting Miniature circuit breaker single pole

0.5A to 2A system and having breaking capacity 10 KA to be erected

in existing box. confirming to IS 8828/1996 with ISI Mark

Miniature circuit breaker single pole suitable to operate on 240 V A.C.

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark

6 to 25 A SP MCB

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity & confirms

to IS : 8828 in existing box having following capacity

6 to 32 A DP MCB

Approved make ELCBs / RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and

suitable for operation on single phase 240 V. having characteristic of

quick action & tripping with all advance feature & do not incorporate no 2.00 1,950.00

any electronic component. for following Max. rating erected as

25 to 32A / 30mA/100 mA DP ELMCB

ESTIMATE Page : 16 of

Approved make ELCBs / RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and

suitable for operation on single phase 240 V. having characteristic of

quick action & tripping with all advance feature & do not incorporate no 2.00 2,213.00

any electronic component. for following Max. rating erected as

40 A / 100 mA DP ELMCB

Providing & erecting 415 V MCB three Pole for Motor & Inductive

Load (C Curve) having 10KA breaking capacity & confirms to IS :8828

in existing box having following capacity

(a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive

Load (C Curve) having 10KA breaking capacity & confirms to IS :8828

in existing box having following capacity

(b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity

6 to 32A FP MCB

Supplying & erecting power contactor for time switch complete

erected as per direction Cat III no 2.00 1,865.00

20 [B] 2 pole 250V 32 Amp.

Supplying & erecting power contactor for time switch complete

erected as per direction Cat III no 2.00 2,755.00

21 [D] 4 pole 440V 40 Amp.

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed.

To Supply & Install Takti (Size 12" X 8 " in 16 gauge M.S. Plate) on

street light pole with painting in the prescribed matter as directed by no 83.00 424.00

23 the engineer in charge and take two photograph of the same takti.

Total amount for MCB

Total amount for MCB

Making trench in soft soil of suitable width of 90 cms deep from the

final ground level or road level for laying cable or locating the fault all

over the run and backfilling the same & clearing the site by removing mt 1,16,093.00 55.00

debris & Shifting of the debris & making site good As per the

Instruction of the Engineer Incharge.

Making trench in Hard murum / Tar Road of suitable width of 90 cms

deep from the final ground level / road level for laying cableor locating

the fault all over the run and backfilling the same and making the mt 29,024.00 74.00

surface proper. by removing debris & Shifting of the debris & making

site good As per the Instruction of the Engineer Incharge.

26 (B) If additional machinery like hammer driller or JCB use [Add] mt 3,207.00 354.00

ESTIMATE Page : 17 of

Covering of cable with second class bricks laid cover the cable

crosswise & also on both sides with covering of 7. 5 Cms. layer of

sand above & below cable (cable shall be laid in 0.9mtr.deep &

Mtr.wide trench). Where there are more than one cable in the trench

on either side of the cable, 5 Cms. over lapping of bricks shall be

Driling the road without breaking the road surface (Asphalt) for laying

of cable for feeding power supply by making Suitable size of holes at

both ends complete.

(A) Up to 100 mm bore dia

Driling the road without breaking the road surface (Asphalt) for laying

of cable for feeding power supply by making Suitable size of holes at

both ends complete.

(B) Up to 150 mm bore dia

Construction of brick masonery pulling chamber 1250 mm x 1250 mm

inside clear size and depth upto 1.2 meter with 350 mm thick

masonery in cerment mortar proporation 1:5,cement finish cement

plaster in CM proportion of 15 mm thickness from inside with 150 mm

thick PCC at bottom with top slab minmum 200 mm thickness in M20

grade with reinforcement. The rate shall be inclusive of providing and

fixing frame and cover of FRC for the Heavy Duty. Rate also inclusive

of excavation and back filling & clearing the site by removing debris &

Shifting of the debris & making site good As per the Instruction of the

Engineer Incharge complete in all respect.

Total Amount for Cable Trench

Total Amount for Cable Trench

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type with

necessary connecting accessories of same material at required depth

for laying of cable. below ground / road surface for enclosing cable

with Excavation and backfilling the same to make ground as per

original. The corrugated pipe shall be able to withstand compression

test at 750 N when reaching a deflection of 5 %.

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type with

necessary connecting accessories of same material at required depth

for laying of cable. below ground / road surface for enclosing cable

with Excavation and backfilling the same to make ground as per

original. The corrugated pipe shall be able to withstand compression

test at 750 N when reaching a deflection of 5 %.

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type with

necessary connecting accessories of same material at required depth

for laying of cable. below ground / road surface for enclosing cable

with Excavation and backfilling the same to make ground as per

original. The corrugated pipe shall be able to withstand compression

test at 750 N when reaching a deflection of 5 %.

Providing & laying. Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II ) Anti Rodent type with

necessary connecting accessories of same material at required depth

for laying of cable. below ground / road surface for enclosing cable

with Excavation and backfilling the same to make ground as per

original. The corrugated pipe shall be able to withstand compression

test at 750 N when reaching a deflection of 5 %.

ESTIMATE Page : 18 of

Providing & laying approved make ISI marked HDPE 6Kg / cm2

(Class-3) as per IS:4984:1995 PE-80 to be erected at road crossing

on or floor as directed for laying of cable. The pipes as following size mt 9,625.00 487.00

of dia & weight per 6 mtr.

(E) 90 mm inner Dia

Providing & laying approved make ISI marked HDPE 6Kg / cm2

(Class-3) as per IS:4984:1995 PE-80 to be erected at road crossing

on or floor as directed for laying of cable. The pipes as following size mt 9,625.00 725.00

of dia & weight per 6 mtr.

(F) 110 mm inner Dia.

Total Amount for pipes

Total Amount for pipes

Supply and laying of XLPE(IS:7098) )(I)-88 ISI marked armored cable

of Cu. / Aluminum conductor of 1.1 KV.grade of following sizes in

ground or in pre-laid DWC pipe / Trenches with necessary cable

identification mark to be provided at distance of 15 mt. & with 2 nos.

of 16 SWG G.I. wire continuous in length per cable.

37 50 sq.mm x 3.5 c Al. cable mt 605.00 282.00

38 35 sq.mm x 3.5 c Al. cable mt 41,250.00 218.00

39 25 sq.mm x 4 c Al. cable mt 33,750.00 189.00

40 16 sq.mm x 4 c Al. cable mt 68,750.00 152.00

41 10 sq.mm x 4 c Al. cable mt 5,50,000.00 139.00

Supplying and laying Flexible PVC insulated multistrand multicore

42 kv grade ISI marked copper wires of following size.

SITC of 1.00 Sq.mm 3 core round PVC sheathed

43 Scope also include the removal of existing wire if required

SITC of 1.50 Sq.mm 3 core round PVC sheathed

44 Scope also include the removal of existing wire if required

SITC of cable with 5 core x 2.5 Sq. mm EPR insulated PVC scheated

Copper Cable with required length from bottom Junction Box to top

junction box of Highmast, with needed all electrical mechanical

accessories and tools to Commission the Highmastt poles as per

tender terms, conditions & Specifications.The scope also includes the

deposition of the existing removed cables and related accessories at

the location as directed by Engineer Incharge Scope also include

the removal of existing wire if required

Cable Termination

Supplying & fixing Double Compression type Brass glands & making

joint with necessary crimping socket of long nack type connecting the

same to various equipment etc. for the following sizes:

46 50 sq.mm x 3.5 c Al. cable no 56.00 150.00

47 35 sq.mm x 3.5 c Al. cable no 2,200.00 150.00

48 25 sq.mm x 4 c Al. cable no 2,200.00 126.00

49 16 sq.mm x 4 c Al. cable no 4,640.00 107.00

50 10 sq.mm x 4 c Al. cable no 1,100.00 90.00

Total Amount for Cable & Termination

Total Amount for Cable & Termination

Street light Poles & High Mast

ESTIMATE Page : 19 of

SITC of approved make FRP Pole having following specifications:

FRP Light Pole made by CNC filament winding machine using

thermoset resin polyester/epoxy resin system) having minimum 62%

glass content. The pole should be in one piece and tapered round in

shape, having smooth finish and should be totally free from corrosion

as well as non conductive & shock proof Pole should be provided with

FRP Anchor Base and it should be heavy duty, or MS Material duly

painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be

UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying

suitable primer system that ensures proper adhesion of the paint.

51 Minimum coating thickness shall be 80 to 100 micron. Deflection of no 321.00 8,934.00

the pole shall not exceed more than 10% of the length of pole for the

given load“ Pole should be generally made as per the dimensional

data, performance criteria and some interchangeability features of

poles as per standard ANSI C 136.20 latest version or ASTM D

4923/01 including cable termination box with necessary accessories .

The size of pole and type of installation with foundation as per

manufacturer details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[C] Overall length of 3.5 Mtr. Average Thickness: 7mm.

Top/ Bottom OD Dia A/F 89/135 mm ± 2mm approx. Approx. Weight

of Pole 15kg. approx. (Without Base) Anchor Base (Size 250X250 &

SITC of approved make FRP Pole having following specifications:

FRP Light Pole made by CNC filament winding machine using

thermoset resin polyester/epoxy resin system) having minimum 62%

glass content. The pole should be in one piece and tapered round in

shape, having smooth finish and should be totally free from corrosion

as well as non conductive & shock proof Pole should be provided with

FRP Anchor Base and it should be heavy duty, or MS Material duly

painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be

UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying

suitable primer system that ensures proper adhesion of the paint.

52 Minimum coating thickness shall be 80 to 100 micron. Deflection of no 161.00 9,696.00

the pole shall not exceed more than 10% of the length of pole for the

given load“ Pole should be generally made as per the dimensional

data, performance criteria and some interchangeability features of

poles as per standard ANSI C 136.20 latest version or ASTM D

4923/01 including cable termination box with necessary accessories .

The size of pole and type of installation with foundation as per

manufacturer details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[D] Overall length of 4 Mtr. Average Thickness: 7mm.

Top/ Bottom OD Dia A/F 89/145 mm ± 2mm approx. Approx. Weight

of Pole 19 kg approx. (Without Base)

Anchor Base (Size 250X250 & 12mm th.)

ESTIMATE Page : 20 of

Supply of approved make FRP Pole having following specifications:

FRP Light Pole made by CNC filament winding machine using

thermoset resin polyester/epoxy resin system) having minimum 62%

glass content. The pole should be in one piece and tapered round in

shape, having smooth finish and should be totally free from corrosion

as well as non conductive & shock proof Pole should be provided with

FRP Anchor Base and it should be heavy duty, or MS Material duly

painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be

UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying

suitable primer system that ensures proper adhesion of the paint.

Minimum coating thickness shall be 80 to 100 micron. Deflection of no 161.00 13,920.00

the pole shall not exceed more than 10% of the length of pole for the

given load“ Pole should be generally made as per the dimensional

data, performance criteria and some interchangeability features of

poles as per standard ANSI C 136.20 latest version or ASTM D

4923/01 including cable termination box with necessary accessories .

The size of pole and type of installation with foundation as per

manufacturer details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight of

Pole 32 kg approx. (Without Base) Anchor Base (Size 300X300 &

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 4 metre having thickness of 4.5 mm, 165 mm

outer uniform dia., with base plate of 450 x 450 x 12 mm with stiffener

plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 321.00 13,243.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 4000mm above GF) (Sample to be approved )

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 6 metre having thickness of 4.5 mm, 165 mm

outer uniform dia., with base plate of 450 x 450 x 12 mm with stiffener

plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 9.00 19,860.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 6000mm above GF) (Sample to be approved )

ESTIMATE Page : 21 of

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 7 metre having thickness of 4.5 mm, 165 mm

outer uniform dia., with base plate of 450 x 450 x 12 mm with stiffener

plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 9.00 23,170.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 7000mm above GF) (Sample to be approved )

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 8 metre having thickness of 4.5 mm, 165 mm

outer uniform dia., with base plate of 450 x 450 x 16 mm with stiffener

plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 321.00 26,480.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 8000mm above GF) (Sample to be approved )

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 9 metre having thickness of 4.5 mm, 165 mm

outer uniform dia., with base plate of 450 x 450 x 16 mm with stiffener

plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 161.00 29,790.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 9000mm above GF) (Sample to be approved )

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 10 metre having thickness of 4.5 mm,

mm outer uniform dia., with base plate of 450 x 450 x 16 mm with

stiffener plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 161.00 33,100.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect (effective length

should be 10000mm above GF) (Sample to be approved)

ESTIMATE Page : 22 of

Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE

for road having Height - 11 metre having thickness of 4.5 mm,

mm outer uniform dia., with base plate of 450 x 450 x 16 mm with

stiffener plate with Seprate integral type junction box ( For Street

light ) , with j bolt, necessary hardware as per detail, with necessary

Reducer / Coupler / for fixing of light fixtures & Hinged access door

with welded chain between pole and hinged door with Allen key no 9.00 36,410.00

access the integral junction box, Fabrication work complete in all

respect as per given detail with one coat of zinc oxide complete in all

respect as per Drawing. Rate shall be including two coats of PU paint

of shade as per drawing or as directed by Architect ( effective length

should be 11000mm above GF) (Sample to be approved )

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 9.00 4,196.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(A) 3 Mtr. Long 70 mm Top X 130 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%) .3 mm

thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and

450mm long with necessary G.I. J Bolts .Approx weight 29 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 65.00 5,501.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and

450mm long with necessary G.I. J Bolts .Approx weight 37 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 9.00 6,806.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole weight 46 kg

ESTIMATE Page : 23 of

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 9.00 8,111.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole weight 59 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 9.00 11,299.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(E) 7 Mtr. Long 70 mm Top X 135 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 225mmX225mmX16mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole weight 67 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 65.00 13,872.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(G) 8 Mtr. Long 70 mm Top X 155 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 260mmX260mmX16mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts Approx Pole weight 84 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 65.00 15,550.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(H) 9 Mtr. Long 70 mm Top X 155 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 3 mm

thickness with 260mmX260mmX16mm base plate, 4-M24 Bolts and

750mm long with necessary G.I. J Bolts .Approx Pole weight 97 kg

ESTIMATE Page : 24 of

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 65.00 19,577.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(I) 10 Mtr. Long 70 mm Top X 175 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 4 mm

thickness with 275mmX275mmX16mm base plate, 4-M24 Bolts and

750mm long with necessary G.I. J Bolts .Approx Pole weight 145 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable no 65.00 25,283.00

foundation (Included) as per details given by manufacturer

considering site requirement.

(J) 11 Mtr. Long 90 mm Top X 210 mm bottom dia (Tolerance are

allowed in all octagonal pole top and bottom dia +/-10%), 4 mm

thickness with 300mmX300mmX20mm base plate, 4-M24 Bolts and

750mm long with necessary G.I. J Bolts .Approx Pole weight 192 kg

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable

foundation (Included) as per details given by manufacturer

considering site requirement.

(K) 12 Mtr. Long 90 mm Top X 240 mm bottom dia, 4 mm thickness

with 320mmX320mmX20mm base plate, 4-M24 Bolts and 850mm

long with necessary G.I. J Bolts .Approx Pole weight 230 kg

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(A) 3 Mtr. Long 70 mm Top X 115 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%),3 mm

ESTIMATE Page : 25 of

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(C) 5 Mtr. Long 70 mm Top X 145 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(D) 6 Mtr. Long 70 mm Top X 160 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(E) 7 Mtr. Long 70 mm Top X 175 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

ESTIMATE Page : 26 of

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(F) 8 Mtr. Long 70 mm Top X 190 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with no 33.00 16,501.00

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(G) 9 Mtr. Long 70 mm Top X 205 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(H) 10 Mtr. Long 80 mm Top X 220 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(I) 11 Mtr. Long 80 mm Top X 245 mm bottom dia (Tolerance are

allowed in all conical pole top and bottom dia +/-10%), 3 mm

ESTIMATE Page : 27 of

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and arrangement for cable

terminations as erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement. The length of poles are as below.

(J) 12 Mtr. Long 80 mm Top X 260 mm bottom dia, 3 mm thickness

supplying & erecting 4.5 Meter G.I. (B Class ERW G.I.Pipes) Swaged

pole with Base Plate ,Single SMC Junction Box with all necessary

electrical mechanical accessories, Earthing jumper, Fastner, Lugs, 2 no 65.00 6,871.00

Nos.Cable Protection Pipes, Painting of pole with numbering etc as

per tender terms and conditions, Specifications and scope of work.

Supplying & erecting 5.5 Meter G.I.(B Class ERW G.I.Pipes) Swaged

pole with Base Plate ,Single SMC Junction Box with all necessary

electrical mechanical accessories, Earthing jumper, Fastner, Lugs, 2 no 1,604.00 7,403.00

Nos.Cable Protection Pipes, Painting of pole with numbering etc as

per tender terms and conditions, Specifications and scope of work.

Supplying & erecting 7.0 Meter G.I.(B Class ERW G.I.Pipes) Swaged

pole with Base Plate ,Single SMC Junction Box with all necessary

electrical mechanical accessories, Earthing jumper, Fastner, Lugs, 2 no 963.00 8,716.00

Nos.Cable Protection Pipes, Painting of pole with numbering etc as

per tender terms and conditions, Specifications and scope of work.

Supplying & erecting 9.5 Meter G.I.(B Class ERW G.I.Pipes) Swaged

pole with Base Plate ,Single SMC Junction Box with all necessary

electrical mechanical accessories, Earthing jumper, Fastner, Lugs, 2 no 1,283.00 12,870.00

Nos.Cable Protection Pipes, Painting of pole with numbering etc as

per tender terms and conditions, Specifications and scope of work.

SITC of extra junction box with all required accessories and one no.

85 cable protection GI pipe of 40 mm dia as per drawing.

SITC of extra junction box with all required accessories and two no.

86 cable protection GI pipe of 40 mm dia as per drawing.

ESTIMATE Page : 28 of

SITC of 9M Conical Bended Hot Dip Galvanized with PU Painted with

Top dia 75mm and Bottom Dia 170mm with pole thickness 3mm

along with Base plate 275mmx275mmx16mm with Single Arm

Bracket of 300mm with provision for 4 nos of foundation bolts. The

steel used for the manufacture of Pole shall comply with BSEN

with yield strength of 355 MP for Conical Pole shaft or equivalent and

the material for the base plate, bracket, flange plates, shall be

equivalent to or better than IS 2062. Hot Dip Galvanizing shall be in

accordance with IS 2629 or latest IS specification. The poles should

be Hot Dip Galvanized to give average thickness of galvanization as

per IS 4759/ BSEN 1461 standards – 65 microns.Test report to be

submitted by manufacturer. All components of the pole and brackets

shall be hot dip galvanized after completion of fabrication.No further

touching up finalizing or modification shall be done after galvanizing. no 65.00 43,700.00

The overall length of each section bracket is immersed in one dipping

operation to ensure smooth and aesthetic finish. No repetition

allowed. They shall be designed and fabricated from such material

and provided with such finish so as to withstand atmospheric

conditions.The poles are to be designed for maximum wind speed of

47 m/s (169 km /hr.) (IS 875 Part-III). The pole shall be evenly

tapered from base to top. The pole shall preferably be fabricated in

section. There shall be no circumferential welded joint in Poles. All

welds shall ensure no fissures inside or outside or outsides surfaces,

and no blowholes. Within the pole there must be Din rail Mounting

provision for MCB & Electrical Connector. Pole must be with 300m

single bracket arm as per shown in drawing. Make / As per approved

SITC of 4M Conical Bended Hot Dip Galvanized with PU Painted with

Top dia 70mm and Bottom Dia 118mm with pole thickness 3mm

along with Base plate 200mmx200mmx12mm with Single Arm

Bracket of 300mm with provision for 4 nos of foundation nut & bolt.

The steel used for the manufacture of Pole shall comply with BSEN

10025 with yield strength of 355 MP for Conical Pole shaft or

equivalent and the material for the base plate, bracket, flange plates,

shall be equivalent to or better than IS 2062. Hot Dip Galvanizing

shall be in accordance with IS 2629 or latest IS specification. The

poles should be Hot Dip Galvanized to give average thickness of

galvanization as per IS 4759/ BSEN 1461 standards –

microns.Test report to be submitted by manufacturer. All components

of the pole and brackets shall be hot dip galvanized after completion

of fabrication.No further touching up finalizing or modification shall be no 33.00 20,125.00

done after galvanizing. The overall length of each section bracket is

immersed in one dipping operation to ensure smooth and aesthetic

finish. No repetition allowed. They shall be designed and fabricated

from such material and provided with such finish so as to withstand

atmospheric conditions.The poles are to be designed for maximum

wind speed of 47 m/s (169 km /hr.) (IS 875 Part-III). The pole shall be

evenly tapered from base to top. The pole shall preferably be

fabricated in section. There shall be no circumferential welded joint in

Poles. All welds shall ensure no fissures inside or outside or outsides

surfaces, and no blowholes. Within the pole there must be Din rail

Mounting provision for MCB & Electrical Connector. Pole must be with

300m single bracket arm as per shown in drawing. Make / As per

approved make list.

ESTIMATE Page : 29 of

SITC of Decorative Pole of 4.2 M column structure with an aesthetic

curved designed single arm decorative bracket. The Pole Shaft

should be fabricated out of Steel tube of grade YST 240. Structurally

designed base plate of Steel Steel of grade E250 Conforming to IS

226/ IS 2062 should be welded with the pole shaft. The structure

should be completely hot-dip galvanized and surface finished with PU

paint. The pole should be of large section at the base with height of

2.7M made up of Tapered fabricated sheet as per IS 1079, welded

with pipe dia of 140mm through which one single ended branch

coming out with dia. 60mm. The base plate shall be of

370mmx370mmx16mm suitable for mounting on 4 nos foundation

bolts. The pole shall be made of Mild Steel with Hot Dip Galvanizing

coating including base plate as per ASTM A123. The pole shall be of

‘composite’ construction designed to withstand specified ‘dead load’

pertaining to the luminaire and its mounting accessories and ‘wind

load’ corresponding to a basic wind speed of 169 kmph without any

deformation or damage to the structure. The welding shall be of high

quality, carried out by qualified welders using approved welding

procedures and tested for its quality through NDT method, such as

DP Test. The pole shaft structure shall be hot dip galvanized through

single dip process as per ASTM A123 and minimum average coating

shall not be less than 65 microns. No mechanical operation, such as

welding, drilling, etc. should be carried out on the pole structure post

hot dip galvanizing. The poles shall have door of about 470 mm

length and shall be vandal resistance and shall be weather proof to

ensure safety of inside connection as approved by the Depts. The

door shall be flush with the exterior surface and shall have suitable

locking arrangement with provision for connectors, MCB, etc. (to be

supplied by others). Complete pole shall be treated with high quality

epoxy zinc primer and thereafter coated with environmentally stable

Polyurethane paint to minimum average DFT of 70 micronsMake / As

89 per approved make list.

SITC of Decorative Pole of 9M column structure with an aesthetic

curved designed Double arm decorative bracket. The Pole Shaft

should be fabricated out of Steel tube of grade YST 240. Structurally

designed base plate of Steel Steel of grade E250 Conforming to IS

226/ IS 2062 should be welded with the pole shaft. The structure

should be completely hot-dip galvanized and surface finished with PU

paint. The pole should be of large section at the base with height of

4M made up of Tapered fabricated sheet as per IS 1079, welded with

pipe dia of 165mm through which two single ended branch coming out

with dia. 76mm. The base plate shall be of 370mmx370mmx16mm

suitable for mounting on 4 nos foundation bolts. The pole shall be

made of Mild Steel with Hot Dip Galvanizing coating including base

plate as per ASTM A123. The pole shall be of ‘composite’

construction designed to withstand specified ‘dead load’ pertaining to

the luminaire and its mounting accessories and ‘wind load’

corresponding to a basic wind speed of 169 kmph without any

deformation or damage to the structure. The welding shall be of high

quality, carried out by qualified welders using approved welding

procedures and tested for its quality through NDT method, such as

DP Test. The pole shaft structure shall be hot dip galvanized through

single dip process as per ASTM A123 and minimum average coating

shall not be less than 65 microns. No mechanical operation, such as

welding, drilling, etc. should be carried out on the pole structure post

hot dip galvanizing. The poles shall have door of about 470 mm

length and shall be vandal resistance and shall be weather proof to

ensure safety of inside connection as approved by the Depts. The

door shall be flush with the exterior surfa ce and shall have suitable

locking arrangement with provision for connectors, MCB, etc. (to be

supplied by others). Complete pole shall be treated with high quality

epoxy zinc primer and thereafter coated with environmentally stable

Polyurethane paint to minimum average DFT of 70 microns.Make / As

90 per approved make list.

ESTIMATE Page : 30 of

SITC of 4 Mtr height Urban Street Light Pole Hot dip Galvanized and

PU painted having pipe size of 100x100 mm square pipe (as per

drawing) with thickness of 3 mm Pole shall be mounted on square

base plate 200*200 *12 mm thickness suitable for mounting on 4 nos

foundation bolts. The pole must have a provision of extended Single

Arm bracket of 500mm length with the provision of integrated IP66

luminaire protected with an IK08 rated polycarbonate lens and

separate control gear compartment. (Protected against 5 joules of

impact, equivalent to a 1.7kg object dropped from 300mm). Overall

System efficacy at 130Lm/W at 4000K CCT. Surge Protection

provided at 10kV for both Common and Differential mode. The Pole

Shaft should be fabricated out of Steel tube of grade YST

Structurally designed base plate of Steel of grade E250 Conforming to

IS 226/ IS 2062 should be welded with the pole shaft. The pole shall

be of ‘composite’ construction designed to withstand specified ‘dead

load’ pertaining to the luminaire and its mounting accessories and

‘wind load’ corresponding to a basic wind speed of 169 kmph without no 6.00 20,125.00

any deformation or damage to the structure. The welding shall be of

high quality, carried out by qualified welders using approved welding

procedures and tested for its quality through NDT method, such as

DP Test. The pole shaft structure shall be hot dip galvanized through

single dip process as per ASTM A123 and minimum average coating

shall not be less than 65 microns. No mechanical operation, such as

welding, drilling, etc. should be carried out on the pole structure post

hot dip galvanizing. The poles shall have door of about 250 mm

length and shall be vandal resistance and shall be weather proof to

ensure safety of inside connection as approved by the Depts. The

door shall be flush with the exterior surface and shall have suitable

locking arrangement with provision for connectors, MCB, etc. (to be

supplied by others). Complete pole shall be treated with high quality

epoxy zinc primer and thereafter coated with environmentally stable

Polyurethane paint to minimum average DFT of 70 microns in closed

91 paint booth chamber.Make / As per approved make list.

SITC of 9Mtr height Urban Street Light Pole Hot dip Galvanized and

PU painted having pipe size of 150x150 mm square pipe (as per

drawing) and Hot Dip Galvanization an LED fixture wattage rating of

90W to 120W. Pole shall be mounted on square base plate 300*300

*16 mm thickness suitable for mounting on 4 nos foundation bolts.

The pole must have a provision of extended Single Arm bracket of 1M

length with the provision of integrated IP66 luminaire protected with

an IK08 rated polycarbonate lens and separate control gear

compartment. Overall System efficacy at 110Lm/W at 4000K CCT.

Surge Protection provided at 10kV for both Common and Differential

mode. The Pole Shaft should be fabricated out of Steel tube of grade

YST 240. Structurally designed base plate of Steel Steel of grade

E250 Conforming to IS 226/ IS 2062 should be welded with the pole

shaft. The pole shall be of ‘composite’ construction designed to

withstand specified ‘dead load’ pertaining to the luminaire and its

mounting accessories and ‘wind load’ corresponding to a basic wind

speed of 169 kmph without any deformation or damage to the

structure. The welding shall be of high quality, carried out by qualified

welders using approved welding procedures and tested for its quality

through NDT method, such as DP Test. The pole shaft structure shall

be hot dip galvanized through single dip process as per ASTM A123

and minimum average coating shall not be less than 65 microns. No

mechanical operation, such as welding, drilling, etc. should be carried

out on the pole structure post hot dip galvanizing. The poles shall

have door of about 250 mm length and shall be vandal resistance and

shall be weather proof to ensure safety of inside connection as

approved by the Depts. The door shall be flush with the exterior

surface and shall have suitable locking arrangement with provision for

connectors, MCB, etc. (to be supplied by others). Complete pole shall

be treated with high quality epoxy zinc primer and thereafter coated

with environmentally stable Polyurethane paint to minimum average

DFT of 70 microns.Make / As per approved make list.

ESTIMATE Page : 31 of

SITC of 9Mtr height Urban Street Light Pole Hot dip Galvanized and

PU painted having pipe size of 150x150 mm square pipe (as per

drawing) with thickness of 3 mm and Hot Dip Galvanization an LED

fixture wattage rating of 90W to 120W. Pole shall be mounted on

square base plate 300*300 *16 mm thickness suitable for mounting

on 4 nos foundation bolts. The pole must have a provision of

extended Single Arm bracket of 1.25M length with the provision of

integrated IP66 luminaire protected with an IK08 rated polycarbonate

lens and separate control gear compartment. Overall System efficacy

at 130Lm/W at 4000K CCT. Surge Protection provided at 10kV for

both Common and Differential mode. The Pole Shaft should be

fabricated out of Steel tube of grade YST 240. Structurally designed

base plate of Steel of grade E250 Conforming to IS 226/ IS

should be welded with the pole shaft. The pole shall be of ‘composite’

construction designed to withstand specified ‘dead load’ pertaining to

the luminaire and its mounting accessories and ‘wind load’

corresponding to a basic wind speed of 169 kmph without any no 6.00 45,425.00

deformation or damage to the structure. The welding shall be of high

quality, carried out by qualified welders using approved welding

procedures and tested for its quality through NDT method, such as

DP Test. The pole shaft structure shall be hot dip galvanized through

single dip process as per ASTM A123 and minimum average coating

shall not be less than 65 microns. No mechanical operation, such as

welding, drilling, etc. should be carried out on the pole structure post

hot dip galvanizing. The poles shall have door of about 250 mm

length and shall be vandal resistance and shall be weather proof to

ensure safety of inside connection as approved by the Depts. The

door shall be flush with the exterior surface and shall have suitable

locking arrangement with provision for connectors, MCB, etc. (to be

supplied by others). Complete pole shall be treated with high quality

epoxy zinc primer and thereafter coated with environmentally stable

Polyurethane paint to minimum average DFT of 70 microns.Make / As

93 per approved make list.

SITC of Type-A, Any kind of 3 to 4.5 mtr ht. Post top lantern Pole (

94 With Basic Rate of Rs. 22500/-)

SITC of Type-B, Any kind of 5 to 5.9 mtr ht. Post top lantern Pole (

95 With Basic Rate of Rs. 30000/-)

SITC of Type-C, Any kind of 6 Mtr. Ht. to 7.9 Mtr. Ht. Decorative

96 Street Light Pole ( with Basic Rate of Rs.35000/-)

SITC of Type-D, Any kind of 8 Mtr. Ht. Decorative Street Light Pole (

97 with Basic Rate of Rs.40000/-)

SITC of Type-E, Any kind of 9 Mtr. Ht. to 12 Mtr. Ht. Decorative Street

98 Light Pole ( with Basic Rate of Rs.45000/-)

Any kind of 0.1 to 2Mtr. Decorative Single Arm Bracket ( with Basic

99 Rate of Rs.7500/-) however not limited to this only.

Any kind of 0.1 to 2Mtr. Decorative Double Arm Bracket ( with Basic

100 Rate of Rs.10000/-) however not limited to this only.

Any kind of 0.1 to 2Mtr. Decorative Three Arm Bracket ( with Basic

101 Rate of Rs.12000/-) however not limited to this only.

SITC of Smart pole as per the Drawings / Specification As per

102 approved make list.

SITC of cement concrete.for foundation or for concrete filling in 1:2:4

ratio with 20 to 25 mm stone metal duly plastered with necessary Cu.Mtr 1,870.00 5,077.00

103 curing for pole muffing or any other purpose.

SITC of TMT Bar FE 500/500D reinforcement for RCC work including

bending, binding and placing in position complete upto floor two level.

SITC of 0.1 to 2 Mtr G.I.bracket with 2 coat P.U. Paint with primer(Any

Arm Bracket as per architect design).

Note : Sample must be Approved from Client / Architect / Consultant

SITC of FRP/GRP arm bracket of having 15˚ arm with 50 mm OD

106 pipe *5 mm thk,1000mm long from pole centre (A) Single arm bracket

SITC of FRP/GRP arm bracket of having 15˚ arm with 50 mm OD

pipe *5 mm thk,1000mm long from pole centre no 65.00 2,390.00

107 (B) Double arm bracket

ESTIMATE Page : 32 of

Supplying & erecting approved make AMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting no 27.00 890.00

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(A) 300mm x 200mm x 100mm [deep]

SITC of electric insulating paint having quantity of paint suitable to

apply upto 6 feet on pole with 5 KV strength and following

specifications:

(Hig electric strength 55 kv/mm, stable upto 200 degree temprature, no 2,750.00 1,530.00

excellent puncture resistant, resistance to fire, excellent resestance to

UV radiation, tough & scratch resistant excellent resistant to

Total Amount of Street Light Pole & Bracket 59

Total Amount of Street Light Pole & Bracket 59

: Luminaries with all electrical accessories are prewired upto the

terminal block & mounted on a removable control gear module for

ease of maintenance. All electrical connections of the control gear

module with the rest of the luminaire should be easily maintainable.

Mounting options should be for pole top mounting

. Note : All Outdoor Fixture should be minimum IP66

Supply and installation of LED street light luminaire with system

power (20W)± 5% , Available in color temperature (4000K-5700K),

CRI>70, SDCM<3 , LEDs used have a life of 50,000 burning hrs. &

Lumen maintenance as per L70 with high power white LEDs wattage

of 3 Watt and above assembled on MCPCB. The Luminaire System

efficacy should be of ≥160LPW at 5700K / ≥150LPW at 4000K /

≥135LPW at 3000K. The fixture housing must be Made of ADC

PDC Aluminum housing for rapid thermal healing & Powder coated by

Corrosion resistant Nano coating technology. The luminaire PCB

Used for Making Light Engine should be Metal Core PCB made of

high grade Al 5052 with minimum 70 micron copper thickness &

W/mk thermal conductivity for better thermal maintenance for light

Engines. Luminaire must have a Ingress protection of IP66 and

Impact Resistance of IK08. The fixture should have an Injection

moulded special PC lens optics ensuring low glare & best in class

uniformity of >0.45. The luminaire must have Integral encapsulated

high efficiency electronic driver of efficiency > 85% having a

Aluminum extrusion construction with rated voltage of 140-270V,

power factor > 0.95, THD < 10%, with Inbuilt surge protection of 10KV

and upgraded with integrated IP67 protected SPD of 20KV/10KA

surge protection with all necessary safety protection like mis-wiring,

Over voltage, Short circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

ESTIMATE Page : 33 of

Supply and installation of LED Street light luminaire with system

power (45W)± 5% , Available in color temperature (4000K-5700K)

CRI>70, SDCM<3 , LEDs used have a life of 50,000 burning hrs. &

Lumen maintenance as per L70 with high power white LEDs wattage

of 3 Watt and above assembled on MCPCB, efficiency more than

150 lm/w. The Luminaire System efficacy should be of >=135LPW. .

The Luminaire System efficacy should be of ≥160LPW at 5700K /

≥150LPW at 4000K / ≥135LPW at 3000K The fixture housing must be

Made of ADC 12 PDC Aluminium housing for rapid thermal healing &

Powder coated by Corrosion resistant Nano coating technology. The

luminaire PCB Used for Making Light Engine should be Metal Core

PCB made of high grade Al 5052 with minimum 70 micron copper

thickness & 2 W/mk thermal conductivity for better thermal

maintanance for light Engines. Luminaire must have a Ingress

protection of IP66 and Impact Resistance of IK08. The fixture should

have an Injection moulded special PC lens optics ensuring low glare

& best in class uniformity of >0.45. The luminaire must have Integral

encapsulated high efficiency electronic driver of efficiency > 85%

having a Aluminium extrusion construction with rated voltage of 140-

270V, power factor > 0.95, THD < 10%, with Inbuilt surge protection

of 10KV and upgraded with integrated IP67 protected SPD of

20KV/10KA surge protection with all necessary safety protection like

mis-wiring, Over voltage, Short circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

112 Technical specifications as Above (#111) no. 33.00 3,312.00

Supply and installation of LED street light luminaire with system

power (60W)± 5% , Available in color temperature (3000K-5700K)

CRI>70, SDCM<3 , LEDs used have a life of 50,000 burning hrs. &

Lumen maintenance as per L70 with high power white LEDs wattage

of 3 Watt and above assembled on MCPCB. The Luminaire System

efficacy should be of ≥160LPW at 5700K / ≥150LPW at 4000K /

≥135LPW at 3000K. The fixture housing must be Made of ADC

PDC Aluminium housing for rapid thermal healing & Powder coated

by Corrosion resistant Nano coating technology. The luminaire PCB

Used for Making Light Engine should be Metal Core PCB made of

high grade Al 5052 with minimum 70 micron copper thickness &

W/mk thermal conductivity for better thermal maintanance for light

Engines.Luminaire must have a Ingress protection of IP66 and Impact

Resistance of IK08. The fixture should have an Injection moulded

special PC lens optics ensuring low glare & best in class uniformity of

>0.45. The luminaire must have Integral encapsulated high efficiency

electronic driver of efficiency > 85% having a Aluminium extrusion

construction with rated voltage of 140-270V, power factor > 0.95, THD

< 10%, with Inbuilt surge protection of 10KV and upgraded with

integrated IP67 protected SPD of 20KV/10KA surge protection with all

necessary safety protection like mis-wiring, Over voltage, Short

circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

114 Technical specifications as Above (#113) no. 93.00 4,948.00

ESTIMATE Page : 34 of

Supply and installation of LED street light luminaire with Dimmable

Driver with system power (90W )± 5% , Available in color temperature

(3000K-5700K) , CRI>70, SDCM<3, LEDs used have a life of

burning hrs. & Lumen maintenance as per L90 with high power white

LEDs wattage of 3 Watt and above assembled on MCPCB. The

Luminaire System efficacy should be of ≥160LPW at 5700K /

≥150LPW at 4000K / ≥135LPW at 3000K. The fixture housing must

be Made of ADC 12 PDC Aluminum housing for rapid thermal healing

& Powder coated by Corrosion resistant Nano coating technology.

The luminaire PCB Used for Making Light Engine should be Metal

Core PCB made of high grade Al 5052 with minimum 70 micron

copper thickness & 2 W/mk thermal conductivity for better thermal

maintenance for light Engines. Luminaire must have a Ingress

protection of IP66 and Impact Resistance of IK08. The fixture should

have an Injection moulded special PC lens optics ensuring low glare

& best in class uniformity of >0.45. The luminaire must have Integral

encapsulated high efficiency electronic driver of efficiency > 85%

having a Aluminum extrusion construction with rated voltage of 140-

270V, power factor > 0.95, THD < 10%, with Inbuilt surge protection

of 10KV and upgraded with integrated IP67 protected SPD of

20KV/10KA surge protection with all necessary safety protection like

mis-wiring, Over voltage, Short circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

116 Technical specifications as above (#115) no. 93.00 5,917.00

117 Supply and installation of LED street light luminaire with Dimmable

Driver with system power (120W)± 5% , Available in color

temperature (4000K-5700K) , CRI>70, SDCM<3 , LEDs used have a

life of 100,000 burning hrs. & Lumen maintenance as per L90 with

high power white LEDs wattage of 3 Watt and above assembled on

MCPCB. The Luminaire System efficacy should be of ≥160LPW at

5700K / ≥150LPW at 4000K / ≥135LPW at 3000K. The fixture housing

must be Made of ADC 12 PDC Aluminum housing for rapid thermal

healing & Powder coated by Corrosion resistant Nano coating

technology. The luminaire PCB Used for Making Light Engine should

be Metal Core PCB made of high grade Al 5052 with minimum

micron copper thickness & 2 W/mk thermal conductivity for better

thermal maintenance for light Engines. Luminaire must have a Ingress

protection of IP66 and Impact Resistance of IK08. The fixture should

have an Injection moulded special PC lens optics ensuring low glare

& best in class uniformity of >0.45. The luminaire must have Integral

encapsulated high efficiency electronic driver of efficiency > 85% no. 514.00 6,501.00

having a Aluminum extrusion construction with rated voltage of 140-

270V, power factor > 0.95, THD

< 10%, with Inbuilt surge protection of 10KV and upgraded with

integrated IP67 protected SPD of 20KV/10KA surge protection with all

necessary safety protection like mis-wiring, Over voltage, Short

circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

118 Technical specifications as above (#117) no. 1,339.00 6,501.00

ESTIMATE Page : 35 of

Supply and installation of LED street light luminaire with Dimmable

Driver with system power (150W)± 5% , Available in color

temperature (3000K-5700K) ,CRI>70, SDCM<3 , LEDs used have a

life of 100,000 burning hrs. & Lumen maintenance as per L90 with

high power white LEDs wattage of 3 Watt and above assembled on

MCPCB. The Luminaire System efficacy should be of ≥160LPW at

5700K / ≥150LPW at 4000K / ≥135LPW at 3000K. The fixture housing

must be Made of ADC 12 PDC Aluminum housing for rapid thermal

healing & Powder coated by Corrosion resistant Nano coating

technology. The luminaire PCB Used for Making Light Engine should

be Metal Core PCB made of high grade Al 5052 with minimum

micron copper thickness & 2 W/mk thermal conductivity for better

thermal maintenance for light Engines. Luminaire must have a Ingress

protection of IP66 and Impact Resistance of IK08. The fixture should no. 129.00 7,798.00

have an Injection moulded special PC lens optics ensuring low glare

& best in class uniformity of >0.45. The luminaire must have Integral

encapsulated high efficiency electronic driver of efficiency > 85%

having a Aluminum extrusion construction with rated voltage of 140-

270V, power factor > 0.95, THD

< 10%, with Inbuilt surge protection of 10KV and upgraded with

integrated IP67 protected SPD of 20KV/10KA surge protection with all

necessary safety protection like mis-wiring, Over voltage, Short

circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab..

120 Technical specifications as above (#119) no. 890.00 7,798.00

Supply and installation of LED street light luminaire with Dimmable

Driver with system power (170W)± 5% , Available in color

temperature (3000K-5700K) , CRI>70, SDCM<3 , LEDs used have a

life of 100,000 burning hrs. & Lumen maintenance as per L90 with

high power white LEDs wattage of 3 Watt and above assembled on

MCPCB. The Luminaire System efficacy should be of ≥160LPW at

5700K / ≥150LPW at 4000K / ≥135LPW at 3000K. The fixture housing

must be Made of ADC 12 PDC Aluminum housing for rapid thermal

healing & Powder coated by Corrosion resistant Nano coating

technology. The luminaire PCB Used for Making Light Engine should

be Metal Core PCB made of high grade Al 5052 with minimum

micron copper thickness & 2 W/mk thermal conductivity for better

thermal maintenance for light Engines. Luminaire must have a Ingress

protection of IP66 and Impact Resistance of IK08. The fixture should no. 129.00 9,018.00

have an Injection moulded special PC lens optics ensuring low glare

& best in class uniformity of >0.45. The luminaire must have Integral

encapsulated high efficiency electronic driver of efficiency > 85%

having a Aluminum extrusion construction with rated voltage of 140-

270V, power factor > 0.95, THD

< 10%, with Inbuilt surge protection of 10KV and upgraded with

integrated IP67 protected SPD of 20KV/10KA surge protection with all

necessary safety protection like mis-wiring, Over voltage, Short

circuit, Reverse Polarity protection.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-

IES, LM 79, LM 80, & TTC certificates will be provided from NABL

accredited lab.

122 Technical specifications as above (#121) no. 825.00 9,018.00

ESTIMATE Page : 36 of

Supply and installation of LED Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on MCPCB,

corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminum with diffuser

and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V, Power Factor more

than 0.95, THD < 10 %, CCT 4000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 145 lumens/watt . LED driver efficiency > 85 no. 93.00 7,195.00

%.( fittings required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.

The Engineer in charge may select any wattage capacity between the

(B) Flood Light (IP-66), Surge protection 10KV integral and, Light

must have 440VAC line supply with over-voltage protection.

(iii) above 90 watts Watts

Supply and installation of LED Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on MCPCB,

corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminum with diffuser

and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V, Power Factor more

than 0.95, THD < 10 %, CCT 4000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 145 lumens/watt . LED driver efficiency > 85 no. 93.00 8,370.00

%.( fittings required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.

The Engineer in charge may select any wattage capacity between the

(B) Flood Light (IP-66), Surge protection 10KV integral and, Light

must have 440VAC line supply with over-voltage protection.

(iv) above 120 watts

Supply and installation of LED Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on MCPCB,

corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD < 10 %, CCT 4000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 145 lumens/watt . LED driver efficiency > 85 no. 93.00 9,552.00

%.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.

The Engineer incharge may select any wattage capacity between the

(B) Flood Light (IP-66), Surge protection 10KV integral and ,Light

must have 440VAC line supply with over-voltage protection.

(v) above 160 watts

ESTIMATE Page : 37 of

Supply and installation of LED Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on MCPCB,

corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminum with diffuser

and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V, Power Factor more

than 0.95, THD < 10 %, CCT 4000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 145 lumens/watt . LED driver efficiency > 85 no. 194.00 10,711.00

%.( fittings required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.

The Engineer in charge may select any wattage capacity between the

(B) Flood Light (IP-66), Surge protection 10KV integral and, Light

must have 440VAC line supply with over-voltage protection.

(vi) above 200 Watts

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminum with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V, Power Factor more

than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.

The Engineer in charge may select any wattage capacity between the

(C) Post Top Lantern LED fitting comprises of finish cast aluminum

spigot and spun aluminum canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and accessories wired upto

terminal block. IP

SITC of Type – A Any kind of Light fixture ( with Basic Rate of

SITC of Type – B Any kind of Light fixture ( with Basic Rate of

SITC of Type – C Any kind of Light fixture ( with Basic Rate of

SITC of Type – D Any kind of Light fixture ( with Basic Rate of

SITC of Type – E Any kind of Light fixture ( with Basic Rate of

SITC of Type – F Any kind of Light fixture ( with Basic Rate of

Total Amount of Light Fixtures 24

Total Amount of Light Fixtures 24

Plate Type Earthing

Supplying & erecting funnel type earthing having earth plate of

following size burred in specifically prepared earth pit 3 mtr. below

ground with 40 kg. charcoal and salt with alternate layers of charcoal

& salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering

& bricks masonry block, C.I. Cover complete as per para 7.3 of IS

3043 with necessary length of double Galvanised Iron / copper earth

wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia.

G.I. pipe 2.5 mtr long complete connected to the nearest switch gear

with end socket as per direction & duly tested by earth tester

confirming to IS (As per drawing) with following specification

134 (C) with 60 x 60x 0.315 cms. Copper earth Plate no 4.00 7,797.00

135 (B) With 45 x 45 x 0.35 cms. G.I. earth plate no 6.00 2,543.00

Chemical Type Earthing -

ESTIMATE Page : 38 of

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of Copper Pipes having Outer

pipe dia of 50mm having , Inner pipe dia of 40 mm , connection

terminal dia of 14 mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for

following type of applications.

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

136 Back filling compound - 1 Nos Bag of 15 Kg.

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

137 Back filling compound - 1 Nos Bag of 25 Kg.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with

necessary coupling buch buried in specially prepared earth pit & G.I. Ea. 2,887.00 815.00

earth wire of 8 SWG erected & connected as directed (For panel)

Earth wire/strips : -

Supply and laying required size Cu/GI. earthing strips for

interconnecting the earthing stations, panels, section piller etc. in built

up trenches, on walls/ceiling, buried in ground generally as specified

and shown on drawings complete with :

a) Fixing accessories.

b) Corrosion protection of buried conductors with bituminous coating

and covered with PVC tapes.

140 No.8 gauge bare cu. earth wire Kg. 219.00 787.00

Providing and erecting HOT deep Galvanised iron strip/ wire 8 to

Total Amount of Earthing

Total Amount of Earthing

Pole dismantling, carting and to submit at AMC store. ( 4 mtr to 10 mtr

The temporary illumination work

Providing of minimum of 10 nos. of LED Flood light minimum

Watt flood light and its temporary wiring in each job in existing road /

service road as per client requirement

Providing , erecting , fabricating the M.S. structure as per requirement

on site incorporating proper size of M.S. angles, flats, bars, channels,

pipes, sections, Sheets & for the pole swaging with the suitable dia

pipe complete with cutting, welding, grinding & finishing duly painted Kg 2,887.00 77.00

with two coat of redoxide with erection on site as per direction of

engineer in charge with necessary gouting, cementing, plastering &

finishing complete as per the instruction of the engineer incharge.

Total Amount of Miscellaneous

Total Amount of Miscellaneous

ESTIMATE Page : 39 of

Document : SECTION-C, CMS AND SECTION FEEDER PANEL WORK

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

Sr. No. Description Amount Rs.

2 New Section Feeder Panel

3 Upgradation Work of Existing Section Feeder Panel

ESTIMATE Page : 40 of

DESCRIPTION UNIT QTY

SITC of a Smart 4G Timer, Supply of lot based 4G Smart Streetlight

Control & Monitoring System having a Smart Panel comprising of 3 Phase

loT Streetlight Smart 4G Timer with 16x2 LCD to display RSSI, relay status,

RTC time & diagnostics.. Controller works on 3-phase & also on any

available 1-Phase., Controller with 8-hour battery backup during external

power failure. External power failure alert immediately to cloud., 110-630 V

AC @ 50-60 Hz 3 phase operating range., Standby power consumption

<3W., Smart 4G Timer with RS232 port for DLMS Energy meter., Smart 4G

Timer must be compatible with any make / brand of DLMS (RS232) Energy

Meter., DI: 4 Nos. (3 Contactor/Latch detection, 1 for Door Sensor.)., DO:

Relays for Independent control each phase (R. Y. B) with 1 extra spare

relay., Smart 4G Timer with dual SIM functionality for connectivity backup..

4G M2M SIM 3-Year communication included., Local configuration via WiFi

/BLE for maintenance or during force majeure., GPS chip inbuilt of Smart 4G

Timer for auto location tracking & astronomic schedule location.,

programmable schedules., Astronomic scheduling with monthly offsets..

Smart 4G Timer has inbuilt timer stores schedules locally & also stores

schedule execution logs locally, syncs to cloud whenever connected to

cloud., Auto-scheduler overrides manual operations.. Monitoring & alerts for

MCB trips.. Over/under voltage, current, overload, power factor & short

circuit protections with alerts via Dashboard, App, SMS, WhatsApp & Email.,

Contactor / Latch chattering protection & alerts., Smart 4G Timer with neutral

failure protection and alert., Bulit-in Watchdog for anti-jamming.. Smart 4G

Timer must send Regular "heartbeat" on software for CCMS status..

Accelerometer for tamper & panel movement detection & alerts.. Smart 4G

Timer must be tested from an NABL Lab for Surge Test @ 6 KV (IEC 61000-

Conducted Emission @ 150 KHz-30 MHz (CISPR11), Damp Heat Test (40

Deg C @ 95% RH) 2 cycles of 12+12 hours (IS: 9000 (Part 5/Sec.2):

latest) with all test passing criteria as "Temporary degradation or loss of

function or performance which is self-recoverable"., FOTA functionality

required for upgrades., Smart 4G Timer sends & stores online/offline data of

controller & load for lamp burn hours analysis..It stores & syncs connectivity

logs for configuration of network connections & analytics., CCMS SMART

SOFTWARE, OAuth 2.0 APIs for sending data to Government

clouds/software, etc., CCMS Web dashboard with secure password & OTP

login., Hosted on trusted cloud, data security, antivirus & attack protection.,

HTTPS., AES256-bit encryption., Vulnerability Assessment and Penetration

Testing (VAPT) certificate for CCMS Software., Streetlight management

software for load status, live analytics & reports., Energy meter data tables

(kW, kWh, PF, I, V, etc.) available., Utility monthly bill reconciliation & Class

1 accuracy reports for billing, energy monitoring & auditing for streetlight

load., Fault detection., Light fault 99% analysis on dashboard using energy

monitoring., WhatsApp integration., Hierarchy-wise reporting & alerts., GIS

mapping of live connected streetlight control panels, poles & streetlights.,

MQTT protocol., Smartphone app with local configuration & navigation.,

Monitoring & reporting of lighting parameters., Facility for media attachments

for site photos/videos/work permits/checklists, etc. per Feeder Panel for

remote verification., Asset management module for streetlight infrastructure

data., Complaint/service task management with history & escalation must be

available., Android & IOS App for dashboard analytics, graphs, energy data,

alerts., 3 Years CCMS Web Software & Cloud Server Hosting subscription

included.. Customizable, user-friendly dashboard..

SITC of PANEL & SWITCHGEAR, The panel made with 2 mm CRCA sheet

with ground mountable stand complete with gland plate, waterproof glands,

earthing bolt., IP55, weatherproof panel with RAL7035 powder-coated..

Smart 4G Timer must be fitted on removable terminal sockets for easy

maintenance.. Also, provide lock & key facility., Panel mount outdoor

antenna for GSM, GPS., Canopy design for draining down water

ESTIMATE Page : 41 of

DESCRIPTION UNIT QTY

SITC of Class 1 DLMS energy meter NABL approved with 1-2 months of

stored data of daily, hourly, monthly, load survey, instantaneous, events,

tamper data & with power events stored in meter memory for audit purpose.,

Must monitor V. I. KWH, KVA, PF. KVAH, etc.The solution must include

wiring, terminal connectors, DIN rail mounting arrangement, and proper

Supply, Installation, Testing and Commissioning (SITC) of a panel-mounted,

multi-circuit energy monitoring system for monitoring 6, 9, 12, or 18 or as per

site requirements outgoing circuits within feeder panels or distribution

boards. The system must enable real-time measurement and reporting of

power, energy, and circuit-level load status to enable efficient energy

management, fault detection, and operational optimization. should be in full

compliance with the requirements and configurations specified in the

detailed technical specifications section.

SITC of feeder panel accessory with switchgear includes 3 Nos. 3 pole

Contactor / Latch having minimum 50 A Load carrying capacity per phase,

5 all other switchgear & wires: 40 A load carrying capacity., 1 Nos. 4P MCB 10 Each 4,000 12,500

kA for Incomer & 6 Nos. 1P MCBs 10 kA for Outgoing.. Phase-Wise Bypass

MCBs required.. 4P RCCB 100 mA.,

ESTIMATE Page : 42 of

DESCRIPTION UNIT QTY

Software Licenses, Design, Development, Delivery and Hosting on Secure

Cloud, Street Light Smart Management Software as described; Secure

Database, Remote Controlling, Monitoring, Power metering features and

Reports Generation & Delivery; Local Language inclusion if needed, API

access and integration support to CMS/ SCADA system; 24 x 7 ticketing

system access; Advance User Rights Management to limit control per User,

Unlimited Users per Project/ Organization, Equipment Activation in LMS,

Local Training on Software platform, All types of Recurring Charges & All

Upgrades, O&M, Bug fixing, Security Updates for two years for

Cabinet Controllers and Outdoor Lamp Controllers. Hosting, Customization

and Delivery of Mobile and Web Applications for Smart Street Light

Management for field activity, maintenance crew, special access control,

event management as described; 24 x 7 ticketing system access; User

Rights Management, Unlimited Users per Project/ Organization, Equipment

Activation in LMS, Training on Mobile apps, All types of Recurring Charges &

All Upgrades, O&M, Bug fixing, Security Updates for Five years for

Cabinet Controllers and Outdoor Lamp Controllers. should be in full

compliance with the requirements and configurations specified in the

detailed technical specifications section.

The scope also includes Supply, Installation, Testing, and Commissioning

(SITC) of a web-based, centralized Helpdesk Software System for managing

service requests, complaints, maintenance calls, and issue tracking across

departments and field teams within the city’s command and control

operations. The system shall support multi-user and multi-role access with

6 configurable workflows, and provide a browser-accessible interface Each 1 3,00,00,000

compatible with desktop and mobile devices. The Helpdesk Software shall

include features such as ticket creation (manual and automated),

assignment, SLA-based escalation, resolution tracking, feedback capture,

and closure with audit trails. It must support multi-channel input including

web portal, email parsing, mobile app integration, and optionally WhatsApp

or SMS bot. The solution shall include a real-time dashboard for ticket

status, SLA compliance, and KPI monitoring, with exportable reports in

PDF/Excel formats. The system must allow user authentication via Role-

Based Access Control (RBAC) and optionally integrate with LDAP/Active

Directory. A searchable internal knowledge base, SOP/document upload

module, and complaint category-wise configuration shall be included. The

backend shall be developed on an open-source stack (Node.js/PHP/Python)

with a relational database (PostgreSQL/MySQL) hosted on a secure Linux-

based server (Ubuntu LTS or RHEL). The software must comply with

Government of India standards on data security, including SSL- encrypted

HTTPS access, OWASP-aligned input validation, and server hardening as

per CERT-In advisories. The system shall be capable of handling a minimum

of 10,000 tickets per month and 500 concurrent users, with automated

backup, restore, and recovery options. The SITC scope includes deployment

(on-premise or cloud), initial configuration, administrator and operator

training, user manual, mobile app (if applicable), SOP documentation, and 5-

year technical support with remote troubleshooting and software updates.

should be in full compliance with the requirements and configurations

specified in the detailed technical specifications section. The scope also

includes the integration of existing nodes through API

Hosting, Customization and Delivery of Mobile and Web Applications for

Smart Street Light Management for field activity, maintenance crew, special

access control, event management as described; 24 x 7 ticketing system

access; User Rights Management, Unlimited Users per Project/

7 Organization, Equipment Activation in LMS, Training on Mobile apps, All Each 1 1,00,00,000

types of Recurring Charges & All Upgrades, O&M, Bug fixing, Security

Updates for five years for 10,000 Cabinet Controllers and Outdoor Lamp

Controllers. should be in full compliance with the requirements and

configurations specified in the detailed technical specifications section.

SITC of Outdoor Lamp Controller / Individual Streetlight Controller (OLC)

with motion sensor based on wireless communication supplied with firmware

8 updates, bug fixes at no additional costs, and complete certifications. 5 year Each 15,000 6,500

standard warranty. should be in full compliance with the requirements and

configurations specified in the detailed technical specifications section.

ESTIMATE Page : 43 of

DESCRIPTION UNIT QTY

SITC of Pole-Mounted Nema-based Outdoor Lamp Controller / Individual

Streetlight Controller (OLC) for retrofitting old streetlight fixtures for wireless

communication supplied with complete with firmware updates, bug fixes at

no additional costs, and complete certifications. 5 year standard warranty.

should be in full compliance with the requirements and configurations

specified in the detailed technical specifications section.

SITC of high-quality, 5-core flexible cable with 2.5 sq.mm cross-sectional

area for power and control signal transmission between pole-mounted

luminaries and NEMA-based streetlight controllers. The cable shall ensure

safe, durable, and weather-resistant operation in outdoor environments,

conforming to relevant IS/IEC standards. Should have 5-core flexible cable,

2.5 sq.mm per core, Suitable for both power supply and signal

10 communication from NEMA controllers to luminaries, Insulated with high- Meter 1,50,000 78

grade PVC/XLPE compound for mechanical and thermal endurance, UV-

resistant, weatherproof and suitable for outdoor installations, Flame-

retardant and low-smoke emission type as per IS 694/IEC 60227, Operating

voltage: up to 1100V, Color-coded cores for easy identification, Compatible

with conduit or pole-mounted clamp installation, Minimum bending radius

and high flexibility for pole-top application

Supply, Installation, Testing, and Commissioning (SITC) of an enterprise-

grade, rack-mounted server system with disaster recovery setup in full

compliance with MeitY (Ministry of Electronics and Information Technology,

Government of India) guidelines for hosting centralized applications such as

Smart Infrastructure Management Software, SCADA, or Street Light

Management Platforms at the City Command Centre. The server shall be of

2U/4U industrial rack-mountable form factor, equipped with dual Intel Xeon

Silver/Gold or AMD EPYC processors with a minimum of 16 physical cores

in total, 128 GB ECC DDR4 RAM (expandable up to 512 GB), and storage

comprising 4 TB NVMe SSD configured in RAID 5 for OS and application

hosting, and 10 TB enterprise grade SATA HDD configured in RAID 6 for

local data archival. The system shall support 4 × 1 Gbps RJ45 and 2 ×

Gbps SFP+ Ethernet interfaces, redundant hot-swappable platinum-rated

power supplies, hardware RAID controller with battery backup unit (BBU),

and remote management capabilities via IPMI/BMC with web-based KVM.

The server shall come pre-installed with a MeitY-compliant operating system

(Ubuntu LTS / RHEL / Windows Server), hardened as per CERT-In security

advisories. A disaster recovery (DR) setup must be commissioned at a

geographically separated Tier III or higher data centre located within India,

ensuring real-time or near-real-time asynchronous data replication with an

RPO of ≤15 minutes and RTO of ≤1 hour. The DR setup shall include

minimum 5 TB usable replicated storage with secure transmission protocols

(SSL/TLS or AES-256 encrypted VPN tunnels), along with scheduled backup

policy (1 Full + 7 Incremental + Monthly Retention), DR drill capability (at

least twice a year), audit-ready SOPs, failover/failback procedures, and 24x7

monitoring dashboard for replication health.The scope shall also include an

online UPS system of minimum 2 kVA rating with ≥60 minutes backup time

using SMF/VRLA batteries, and a 16-port managed Layer 2/3 industrial

Ethernet switch with VLAN, QoS, SNMP support. All power/data/network

cables, connectors, rack-mount kits, documentation, testing tools, licenses (if

applicable), training for staff, and commissioning services shall be included

as part of the SITC deliverables. should be in full compliance with the

requirements and configurations specified in the detailed technical

specifications section.

ESTIMATE Page : 44 of

DESCRIPTION UNIT QTY

SITC of a desktop workstation for individual operators at the zone level. The

workstation must be suitable for operating the Street Light Management

Software and handling administrative and reporting tasks. It shall come pre-

installed with a licensed Windows Operating System, MS Office suite,

antivirus software, and necessary drivers. The system should have

appropriate processing power, RAM, and display resolution for multi-window

monitoring and data processing. should be in full compliance with the

requirements and configurations specified in the detailed technical

12 specifications section. Each 10 1,25,000

Intel® Core™ i7-12th generation, 4.0 GHz or higher, Minimum 32GB RAM,

Minimum 512 GB separate SSD hard drive for OS and 1TB HDD for Data,

DVD R/W, Graphics Adapter - Intel®IRIS XE Graphics or equivalent for local

client GPU rendering support, latest Windows professional OS (64-bit OS

versions recommended), Video Monitor Resolution- 1280x1024 pixels, 32 bit

with keyboard and mouse. with all required software like MS office, 5Year

antivirus etc..

SITC of of cellular / IoT data connectivity for smart streetlight controllers and

feeder-level equipment, enabling real-time communication with the central

LMS platform. The charges cover SIM card provisioning, activation, and

monthly data usage for device communication. The service must ensure

secure, uninterrupted data transmission with sufficient bandwidth and

fallback mechanisms as applicable. The recurring charges shall be paid in

the O&M section by the department on a monthly basis upon submission of

invoice and usage details.

SITC of of qualified and trained support staff from the OEM for on-site

operation, maintenance, and technical support at the Control Command

Centre. The deployment shall cover THREE shifts per day (24X7) to ensure

round-the-clock availability of personnel for managing the Street Light

Management Software, attending to alerts, coordinating with field teams, and Per

generating daily/weekly reports. The staff shall also assist in troubleshooting, Person

routine diagnostics, and training of municipal personnel as required.

Hour/Shift for 7 Days week, 3 Person for 60 months should be in full

compliance with the requirements and configurations specified in the

detailed technical specifications section.

CMS Work Total Amount

CMS Work Total Amount

Section Feeder Panels Type-A

ESTIMATE Page : 45 of

DESCRIPTION UNIT QTY

Supplying, unloading at site, shifting to site, assembling, leveling, grouting,

erecting, Testing, & Commissioning of Smart 4G Timer, Supply of lot based

4G Smart Streetlight Control & Monitoring System having a Smart Panel

comprising of 3 Phase loT Streetlight Smart 4G Timer with 16x2 LCD to

display RSSI, relay status, RTC time & diagnostics.. Controller works on 3-

phase & also on any available 1-Phase., Controller with 8-hour battery

backup during external power failure. External power failure alert

immediately to cloud., 110-630 V AC @ 50-60 Hz 3 phase operating range.,

Standby power consumption <3W., Smart 4G Timer with RS232 port for

DLMS Energy meter., Smart 4G Timer must be compatible with any make /

brand of DLMS (RS232) Energy Meter., DI: 4 Nos. (3 Contactor/Latch

detection, 1 for Door Sensor.)., DO: 3 Relays for Independent control each

phase (R. Y. B) with 1 extra spare relay., Smart 4G Timer with dual SIM

functionality for connectivity backup.. 4G M2M SIM 3-Year communication

included., Local configuration via WiFi /BLE for maintenance or during force

majeure., GPS chip inbuilt of Smart 4G Timer for auto location tracking &

astronomic schedule location., 50 programmable schedules., Astronomic

scheduling with monthly offsets.. Smart 4G Timer has inbuilt timer stores

schedules locally & also stores schedule execution logs locally, syncs to

cloud whenever connected to cloud., Auto-scheduler overrides manual

operations.. Monitoring & alerts for MCB trips.. Over/under voltage, current,

overload, power factor & short circuit protections with alerts via Dashboard,

App, SMS, WhatsApp & Email., Contactor / Latch chattering protection &

alerts., Smart 4G Timer with neutral failure protection and alert., Bulit-in

Watchdog for anti-jamming.. Smart 4G Timer must send Regular "heartbeat"

on software for CCMS status.. Accelerometer for tamper & panel movement

detection & alerts.. Smart 4G Timer must be tested from an NABL Lab for

Surge Test @ 6 KV (IEC 61000-4-5), ESD Test @ 4 KV (IEC 61000-4-2),

EFT @ 2 KV (IEC 61000-4-4), Conducted Emission @ 150 KHz-30 MHz

(CISPR11), Damp Heat Test (40 Deg C @ 95% RH) 2 cycles of 12+12 hours

(IS: 9000 (Part 5/Sec.2): 1981 latest) with all test passing criteria as

"Temporary degradation or loss of function or performance which is self-

recoverable"., FOTA functionality required for upgrades., Smart 4G Timer

sends & stores online/offline data of controller & load for lamp burn hours

15 analysis.. It stores & syncs connectivity logs for configuration of network no 1,085 1,00,000

connections & analytics., PANEL & SWITCHGEAR, The panel includes a

Class 1 DLMS energy meter NABL approved with 1-2 months of stored data

of daily, hourly, monthly, load survey, instantaneous, events, tamper data &

with power events stored in meter memory for audit purpose., Must monitor

V. I. KWH, KVA, PF. KVAH, etc.. Panel made with 2 mm CRCA sheet with

ground mountable stand complete with gland plate, waterproof glands,

earthing bolt., IP55, weatherproof panel with RAL7035 powder-coated..

Smart 4G Timer must be fitted on removable terminal sockets for easy

maintenance.. Switchgear includes 3 Nos. 3 pole Contactor / Latch having

minimum 50 A Load carrying capacity per phase, all other switchgear &

wires: 40 A load carrying capacity., 1 Nos. 4P MCB 10 kA for Incomer &

Nos. 1P MCBs 10 kA for Outgoing.. Phase-Wise Bypass MCBs required.. 4P

RCCB 100 mA., door sensor. Also, provide lock & key facility., Panel mount

outdoor antenna for GSM, GPS., Canopy design for draining down water.,

CCMS SMART SOFTWARE, OAuth 2.0 APIs for sending data to

Government clouds/software, etc., CCMS Web dashboard with secure

password & OTP login., Hosted on trusted cloud, data security, antivirus &

attack protection., HTTPS., AES256-bit encryption., Vulnerability

Assessment and Penetration Testing (VAPT) certificate for CCMS Software.,

Streetlight management software for load status, live analytics & reports.,

Energy meter data tables (kW, kWh, PF, I, V, etc.) available., Utility monthly

bill reconciliation & Class 1 accuracy reports for billing, energy monitoring &

auditing for streetlight load., Fault detection., Light fault 99% analysis on

dashboard using energy monitoring., WhatsApp integration., Hierarchy-wise

reporting & alerts., GIS mapping of live connected streetlight control panels,

poles & streetlights., MQTT protocol., Smartphone app with local

configuration & navigation., Monitoring & reporting of lighting parameters.,

Facility for media attachments for site photos/videos/work permits/checklists,

etc. per Feeder Panel for remote verification., Asset management module for

streetlight infrastructure data., Complaint/service task management with

history & escalation must be available., Android & IOS App for dashboard

analytics, graphs, energy data, alerts., 3 Years CCMS Web Software &

Cloud Server Hosting subscription included.. Customizable, user-friendly

Section Feeder Panels Type-B

ESTIMATE Page : 46 of

DESCRIPTION UNIT QTY

SITC of , unloading at site, shifting to site, assembling, leveling, grouting,

erecting, Testing, & Commissioning of Smart 4G Timer, Supply of lot based

4G Smart Streetlight Control & Monitoring System having a Smart Panel

comprising of 3 Phase loT Streetlight Smart 4G Timer with 16x2 LCD to

display RSSI, relay status, RTC time & diagnostics.. Controller works on 3-

phase & also on any available 1-Phase., Controller with 8-hour battery

backup during external power failure. External power failure alert

immediately to cloud., 110-630 V AC @ 50-60 Hz 3 phase operating range.,

Standby power consumption <3W., Smart 4G Timer with RS232 port for

DLMS Energy meter., Smart 4G Timer must be compatible with any make /

brand of DLMS (RS232) Energy Meter., DI: 4 Nos. (3 Contactor/Latch

detection, 1 for Door Sensor.)., DO: 3 Relays for Independent control each

phase (R. Y. B) with 1 extra spare relay., Smart 4G Timer with dual SIM

functionality for connectivity backup.. 4G M2M SIM 3-Year communication

included., Local configuration via WiFi /BLE for maintenance or during force

majeure., GPS chip inbuilt of Smart 4G Timer for auto location tracking &

astronomic schedule location., 50 programmable schedules., Astronomic

scheduling with monthly offsets.. Smart 4G Timer has inbuilt timer stores

schedules locally & also stores schedule execution logs locally, syncs to

cloud whenever connected to cloud., Auto-scheduler overrides manual

operations.. Monitoring & alerts for MCB trips.. Over/under voltage, current,

overload, power factor & short circuit protections with alerts via Dashboard,

App, SMS, WhatsApp & Email., Contactor / Latch chattering protection &

alerts., Smart 4G Timer with neutral failure protection and alert., Bulit-in

Watchdog for anti-jamming.. Smart 4G Timer must send Regular "heartbeat"

on software for CCMS status.. Accelerometer for tamper & panel movement

detection & alerts.. Smart 4G Timer must be tested from an NABL Lab for

Surge Test @ 6 KV (IEC 61000-4-5), ESD Test @ 4 KV (IEC 61000-4-2),

EFT @ 2 KV (IEC 61000-4-4), Conducted Emission @ 150 KHz-30 MHz

(CISPR11), Damp Heat Test (40 Deg C @ 95% RH) 2 cycles of 12+12 hours

(IS: 9000 (Part 5/Sec.2): 1981 latest) with all test passing criteria as

"Temporary degradation or loss of function or performance which is self-

recoverable"., FOTA functionality required for upgrades., Smart 4G Timer

sends & stores online/offline data of controller & load for lamp burn hours

16 analysis.. It stores & syncs connectivity logs for configuration of network no 725 85,000

connections & analytics., PANEL & SWITCHGEAR, The panel includes a

Class 1 DLMS energy meter NABL approved with 1-2 months of stored data

of daily, hourly, monthly, load survey, instantaneous, events, tamper data &

with power events stored in meter memory for audit purpose., Must monitor

V. I. KWH, KVA, PF. KVAH, etc.. Panel made with 2 mm CRCA sheet with

ground mountable stand complete with gland plate, waterproof glands,

earthing bolt., IP55, weatherproof panel with RAL7035 powder-coated..

Smart 4G Timer must be fitted on removable terminal sockets for easy

maintenance.. Switchgear includes 3 Nos. 3 pole Contactor / Latch having

minimum 50 A Load carrying capacity per phase, all other switchgear &

wires: 40 A load carrying capacity., 1 Nos. 4P MCB 10 kA for Incomer &

Nos. 1P MCBs 10 kA for Outgoing.. Phase-Wise Bypass MCBs required.. 4P

RCCB 100 mA., door sensor. Also, provide lock & key facility., Panel mount

outdoor antenna for GSM, GPS., Canopy design for draining down water.,

CCMS SMART SOFTWARE, OAuth 2.0 APIs for sending data to

Government clouds/software, etc., CCMS Web dashboard with secure

password & OTP login., Hosted on trusted cloud, data security, antivirus &

attack protection., HTTPS., AES256-bit encryption., Vulnerability

Assessment and Penetration Testing (VAPT) certificate for CCMS Software.,

Streetlight management software for load status, live analytics & reports.,

Energy meter data tables (kW, kWh, PF, I, V, etc.) available., Utility monthly

bill reconciliation & Class 1 accuracy reports for billing, energy monitoring &

auditing for streetlight load., Fault detection., Light fault 99% analysis on

dashboard using energy monitoring., WhatsApp integration., Hierarchy-wise

reporting & alerts., GIS mapping of live connected streetlight control panels,

poles & streetlights., MQTT protocol., Smartphone app with local

configuration & navigation., Monitoring & reporting of lighting parameters.,

Facility for media attachments for site photos/videos/work permits/checklists,

etc. per Feeder Panel for remote verification., Asset management module for

streetlight infrastructure data., Complaint/service task management with

history & escalation must be available., Android & IOS App for dashboard

analytics, graphs, energy data, alerts., 3 Years CCMS Web Software &

Cloud Server Hosting subscription included.. Customizable, user-friendly

New Section Feeder Panel Work

ESTIMATE Page : 47 of

DESCRIPTION UNIT QTY

Removing of Section Feeder Panel

Dismantling and removing of existing section feeder pillar as said location by

engineer in charge complete in all respect as it is original with necessary civil

work foundation, cable termination, with extra required various sizes cables

& with cable joints if needed etc. as per requirement or as per instruction of

engineer in charge.

Installation of Section Feeder Panel

Installation Testing and Commissioning of New / existing section feeder pillar

as said location by engineer in charge complete in all respect as it is original

with necessary cable termination, with extra required various sizes cables &

with cable joints if needed etc. as per requirement or as per instruction of

engineer in charge.

Upgradation of Section Feeder Panel

Upgradation of existing section feeder pillar Install MCB instead of Fuse as

said location by engineer in charge complete in all respect as it is original

with necessary cable termination, with extra required various sizes cables &

with cable joints if needed etc. as per requirement or as per instruction of

engineer in charge.

SITC of the MCB's ( 10 KA ) Timers , & Contactors With the Dinrail Channel

20 providing and erecting Miniature circuit breaker single pole 0.5A to 2A no 14,225 268

system and having breaking capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark

Miniature circuit breaker single pole suitable to operate on 240 V A.C.

21 system and having breaking capacity 10 KA to be erected in existing box. no 6,000 111

confirming to IS 8828/1996 with ISI Mark 6 to 25 A SP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive

22 load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in no 1,000 297

existing box having following capacity 6 to 32 A DP MCB

Approved make ELCBs / RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable

for operation on single phase 240 V. having characteristic of quick action &

tripping with all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed 25 to 32A /

30mA/100 mA DP ELMCB

24 40 A / 100 mA DP ELMCB no 7 2,213

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C

25 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box no 103 522

having following capacity (a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C

26 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box no 6 641

having following capacity (b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

27 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box no 500 730

having following capacity 63A FP MCB

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

28 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box no 500 662

having following capacity 40A FP MCB

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

29 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box no 150 590

having following capacity 6 to 32A FP MCB

Supplying & erecting power contactor for time switch complete erected as

per direction Cat III [B] 2 pole 250V 32 Amp.

Supplying & erecting power contactor for time switch complete erected as

per direction Cat III [D] 4 pole 440V 40 Amp.

ESTIMATE Page : 48 of

DESCRIPTION UNIT QTY

Supplying & erecting approved make Digital time switch having lithium cell

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

32 contacts Minimum switching setup time 1 minimum & LCD display. Also no 1,000 3,137

comprised permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

Upgradation Amount for Section Feeder Panel

ESTIMATE Page : 49 of

Document : SECTION-D, AI WORK

Project : Street Light Work Ahmedabad

Client : Ahmedabad Municipal Corporation

Sr. No. Description Amount Rs.

ESTIMATE Page : 50 of

DESCRIPTION UNIT QTY

AI Engine Infrastructure Platform

Supply, Installation, Testing, and Commissioning of the complete on- premises

1 hardware and foundational software stack. This platform is designed as a high- Set - - -

availability cluster to provide the resilient and high- performance computational

power required for all specified AI functionalities, including future-readiness for

large-scale (70B+ parameter) AI models.

Inference Servers (High Availability Pair): For real-time processing of all AI

1.1 models. Each of the two servers to be equipped with 2x NVIDIA H200 80GB Set 1 1,68,72,400

GPUs (NVLink), 1.5 TB DDR5 RAM, 32-64 core CPU (AMD EPYC/Intel Xeon),

and 2 TB NVMe SSD.

AI Model Training Servers (High Availability Pair): A dedicated HA cluster for

1.2 the periodic offline retraining of all AI models. Each of the two servers to be Set 1 2,18,26,800

equipped with 2x NVIDIA H200 80GB GPUs (NVLink), 2 TB DDR5 RAM, 64-

core CPU, and 8 TB NVMe SSD.

Database Servers (High Availability Pair): A High Availability (1+1) cluster for

1.3 structured data storage. Each node to have a 32-core CPU, 512 GB RAM, and 1 98,68,200

High-Speed NAS Storage: For storing historical logs, datasets, and AI model

1.4 checkpoints. 50 TB high-performance SSD-based storage (RAID 10) with 10- Nos 1 86,74,600

25 GbE uplinks.

Monitoring, Logging & Load Balancing Servers (HA Pair): A High Availability

1.5 (1+1) cluster for system monitoring (Prometheus, Grafana), logging, and Set 1 78,62,860

request distribution.

1.6 High-Speed Network Switches (HA Pair): A High Availability (1+1) pair of 25- 40 Set 1 48,62,800

GbE Managed Switches with VLAN Support for low-latency connectivity.

Security Appliances (Firewall HA Cluster): A High Availability cluster of Next-

1.7 Generation Firewalls with DDoS & SSL inspection to protect all system Set 1 82,96,480

Core Platform & Virtualization Software Licenses: Includes all necessary OS,

1.8 virtualization, and container platform licenses to operate the entire hardware L.S 1 2,28,46,800

cluster as a unified, resilient private cloud.

LMS AI Software Platform

Supply of all proprietary application software required to operate the AI

Analytics and Optimization Engine. The software platform must grant the right

to use the specified modules across the entire network of assets and support

the high-availability hardware cluster.

Core AI Engine Components

2.1 Foundational software components responsible for data processing, real- time L.S - - -

analysis, and model deployment, forming the backend "brain" of the entire

Data Ingestion & ETL Platform: Core component for scalable intake of telemetry

2.1.1 from 207,000+ endpoints, performing data cleaning, transformation, and L.S 1 2,96,78,400

preparation for storage and analysis.

Real-time Stream Processing Engine: Core engine for analyzing data streams

2.1.2 in motion, enabling immediate alerts and actions for dynamic control and fault L.S 1 2,84,82,600

AI Model Serving & Inference Engine: Core runtime engine responsible for

2.1.3 deploying, managing, and serving predictions from all trained AI models with L.S 1 2,92,46,800

2.2 AI Application Model Packs L.S - - -

2.2.1 Predictive Failure AI Models Pack: The trained models (e.g., Gradient Boosting, L.S 1 1,94,64,600

LSTMs) for predicting failures in luminaires, drivers, and controllers

Power Grid Anomaly & Theft Detection AI Models Pack: The trained models

2.2.2 (e.g., Isolation Forests, Autoencoders) for identifying anomalies in power quality L.S 1 1,86,75,400

2.2.3 Energy Forecasting AI Models Pack: The trained time-series models (e.g., L.S 1 1,94,67,200

ARIMA, Prophet) for predicting energy consumption.

ESTIMATE Page : 51 of

DESCRIPTION UNIT QTY

2.2.4 Adaptive Lighting Data Fusion AI Models Pack: The trained models for fusing L.S 1 1,87,68,480

traffic, weather, and event data to create dynamic lighting profiles.

2.2.5 NLP & Sentiment Analysis AI Models Pack: The trained NLP models (e.g., L.S 1 1,98,76,860

BERT-based classifiers) for citizen feedback classification and analysis.

Application & Visualization Suites

2.3 The user-facing software components (dashboards, control panels, and L.S - - -

reporting tools) that allow operators to interact with and manage the insights

generated by the AI engines.

Predictive Maintenance & Asset Health Suite: The dashboard for maintenance

2.3.1 teams to visualize asset health scores, RUL estimates, and a map-based view L.S 1 1,18,67,500

of predicted faults.

Dynamic Lighting & Scene Management Suite: The control panel for lighting

2.3.2 operators to create, manage, and deploy dynamic lighting profiles L.S 1 98,76,400

recommended by the AI.

Energy Analytics & Optimization Suite: The dashboard for energy managers to

2.3.3 visualize consumption trends, forecasts, and potential savings identified by the L.S 1 92,97,520

analytics engine.

Citizen Service & Helpdesk Integration Suite: The interface for helpdesk teams

2.3.4 to view and manage auto-classified and prioritized tickets generated by the NLP L.S 1 85,84,200

Geospatial Intelligence & Reporting Suite: The reporting tool for exporting

2.3.5 aggregated data like traffic heatmaps and fault concentration maps for use in L.S 1 96,76,800

external GIS and urban planning software.

3 Professional & Operational Services L.S - - -

One-Time Implementation & Setup Services

3.1 Covers all one-time professional services required to successfully deploy, L.S - - -

configure, integrate the AI Engine, and train the initial models to ensure the

system is ready for operation.

Infrastructure Deployment & Integration: Covers the complete physical

3.1.1 deployment, logical configuration of the HA cluster, and integration with existing L.S 1 1,68,74,000

city data sources.

Initial AI Model Training & Calibration: Covers the professional data science

3.1.2 services for the first cycle of data ingestion, training, and calibration of all L.S 1 2,96,46,800

specified AI models to establish a baseline performance.

Yearly Operations & Management Services - After Successful Implementation

4 Covers all recurring services required to operate, maintain, and support the AI L.S - - -

Engine platform annually. The quantity reflects a 5-year operational period.

Annual Hardware Maintenance Contract (AMC): Comprehensive on-site

4.1 support, spares, and maintenance for all hardware components listed in Section L.S 5 60,00,000

Annual Software Platform & Application Support: Covers updates, security

4.2 patches, and technical support for all software listed in Section 14.8 and L.S 5 60,00,000

AI Model Monitoring, Retraining & Optimisation Services: Professional data

science services for continuous monitoring of model performance, periodic

retraining with new data, and optimisation of AI algorithms. Including Man

Managed Security & Infrastructure Operations: 24/7 monitoring of the platform

4.4 for security threats, performance bottlenecks, and operational management of L.S 60 4,00,000

the HA infrastructure. Including Man Power

ESTIMATE Page : 52 of