Civil Work

Name of Work: Package: Construction of New Animal Husbandary Epic Center at (1) Sarsavani

(2) Latipura and (3) Mujpur, Ta. Padra, Dist. Vadodara (Deposit Work)

BILL OF QUANTITIES

It. No. Description of Item Quantity Unit Rate in Figure Total

1 Excavation for foundation upto 1.5 m depth including sorting out 854.89 Cu.mt 250.90

and stacking of useful materials and disposing off the excavated

stuff upto any lead. (B) Dense or Hard soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m including 162.78 Cu.mt 289.92

sorting out and stacking of useful materials and disposing off the

excavated stuff upto any lead. (B) Dense or Hard soil

3 Providing and laying cement concrete work 1:2:4 (1- Cement : 2- 112.50 Cu.mt 4135.13

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

and curing complete Including cost of formwork But Excluding The

Cost Of reinforcement for reinforced concrete work in (A)

Foundations, footings, Base or columns and Mass concrete . (For

4 Providing and laying controlled cement concrete M.250 and curing 54.37 Cu.mt 4642.97

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundations,

footings, Base of columns and Mass concrete. (For Footing)

5 Providing and laying controlled c.c. M.250 & curing complete 12.21 Cu.mt 7742.66

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Collumns, pillars,

posts & struts upto floor two level for G.F. (For Column Up to PL)

6 Providing and laying controlled cement concrete M.250 and curing 33.47 Cu.mt 5875.17

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (C) Slabs, landing,

shelves, Balconies, Lintels, Beams, Girders and Cantilever upto

floor two level.(For Ground Beam)

7 Filling available excavated earth (Excluding rock) in trenches plinth, 814.95 Cu.mt 133.65

sides of foundation etc in layers not exceeding 20 cm in depth

consolidating each deposited layer by ramming and watering.

8 Filling in foundation and plinth with murrum or selected soil in layers 42.99 Cu.mt 296.29

of 20cm. thickness including watering, ramming and consolidating

9 Filling in plinth with sand under floors including watering, ramming 11.37 Cu.mt 471.69

consolidating and dressing etc. complete.

10 Anti-Termite System:Providing and laying of permanent piping 227.49 Sq.mt 134.33

technology anti-termite treatment before flooring work by installing

LLDP (Low linear density polyethylene) tube of 8 mm O.D. &

mm 1.D. with inbuilt pressure compensation chip every 30 cm

interval in the tube, having working pressure of 2 Kg/cm2 and

release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP pipe

shall be installed at the entire periphery of the building and at

internal network of building at a depth of 20 to 200 mm under floor

at every 2 to 3 mtr. c/c distance (adjusted as per building layout ) &

Ends of loop pass through a PVC elbow of minimum 32 mm ID at

junction box of wall and floor level, entering into a steel reinforced

grooved flexible pipe of minimum 22 mm ID leading into junction

box and the loops shall terminate in junction boxes & test every

junction during injecting chemicals for termite control treatment. The

anti termite chemical Imidacloprid 30.5% SC mix as per IS-6313

(part III) shall be injected by the pressure pump diluted with water @

10.5 ml/5 ltr of water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The

contractor shall submit approved line plan for piping system and

junction boxes dully approved by Engineer-in-Charge with bond of

year warranty.(i)Anti Termite chemical injected area (Chemical

injecting incl. labour cost)

11 Providing and laying damp proof course 25mm thick cement 35.04 Sq.mt 304.53

concrete 1:2:4 (1-Cement : 2 coarse sand : 4 stone aggregate

mm nominal size) and curing complete.

It. No. Description of Item Quantity Unit Rate in Figure Total

12 Brick work using common burnt clay building bricks having crushing 15.12 Cu.mt 4121.55

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventiona( For

B/w Up to Plinth)

13 Brick work using Common burnt clay building bricks having 127.05 Cu.mt 4396.56

crushing strength not less than 35 kg/sq.cm in Super Structure

above floor Two Level in cement mortar 1:6 ( 1 cement : 6 fine sand

) (B) Conventional.( For B/W Uo to GF Slab)

14 Half brick masonry in common brunt clay building bricks having 36.99 Sq.mt 667.96

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4

(1- Cement : 4 -coarse sand ) in Superstructure above plinth level

up to floor two Level(B) Conventional

15 Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse 12.38 Cu.mt 3993.11

sand : 6- crushed stone aggregates 20 mm nominal size) and

curing complete including cost of formwork in (A) Wall Caps /

16 Providing and laying controlled cement concrete M.200 and curing 8.97 Cu.mt 7230.59

complete excluding the cost of formwork and reinforcement for

reinforced concrete work in (C) Slabs, landing, shelves, Balconies

Lintels, Beams, Girders and Cantilever upto floor two level. (For

17 Providing and laying controlled c.c. M.200 & curing complete 19.14 Cu.mt 7677.01

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Collumns, pillars,

posts & struts upto floor two level for G.F.(For Column)

18 Providing and laying controlled cement concrete M.200 and curing 27.45 Cu.mt 6336.74

complete Including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (C) Slabs, landing,

shelves, Balconies Lintels, Beams, Girders and Cantilever upto

floor two level. (For Beam)

19 Providing and laying controlled cement concrete M.200 and curing 34.14 Cu.mt 4693.47

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (C) Slabs, landing,

shelves, Balconies Lintels, Beams, Girders and Cantilever upto

floor two level.(For Grade slab)

20 Providing and laying controlled cement concrete M.200 and curing 36.84 Cu.mt 6432.69

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (C) Slabs, landing,

shelves, Balconies Lintels, Beams, Girders and Cantilever upto

floor two level.(For slab)For GF Slab

21 Providing TMT Bar FE 500D reinforcement for R.C.C. work 30273.50 Kg 77.29

including bending ,binding and placing in position complete up to

floor two level

22 Providing and fixing M.S. Fan clamps type 1 to 16mm diaM.S. bar 30.00 Nos 131.93

bent to shape with hooked ends to R.C.C. slabscuring, laying

including painting the exposed portion ofloops, all as per standard

design complete

23 Providing & fixing 40 mm thick Single shutter flush door solid core 20.16 Sq.mt 7424.51

finished with both side 1 mm thick lamination both side like

'NOVAPAN 'or equivalent, of natural wood grain shade as approved

by this office having telephone black granite 18 mm thick frame with

double stone as per the instruction of Engineer in charge.with

necessary SS hinges and fixtures etc . complete.

24 Providing & fixing 35 mm thick Single shutter flush door solid core 4.74 Sq.mt 7015.46

finished with both side 1 mm thick laminationboth side like

'NOVAPAN 'or equivalent, of natural wood grain shade as approved

by this office having telephone blackgranite 18 mm thick frame with

double stone including fixed ventilation above lintle level as per drg

and as per theinstruction of Engineer in charge.with necessary SS

hinges and fixtures etc . complete.

It. No. Description of Item Quantity Unit Rate in Figure Total

25 Providing and fixing window having extruded aluminum colour 21.60 Sq.mt 3199.68

anodized section frame main outer size 95mm x 24mm x 1.17mm

(of Jindal section no.2459 @ Wt. 0.738 Kg/mt), horizontal three

track member size 92mm x 31.75mm x 1.30mm (of Jindal section

no. 8688, @ Wt. 1.07 Kg/mt), vertical member of size 92mm

31.75mm x 1.50mm (of Jindal section no. 8933 @ Wt. 1.06 Kg/mt)

with sliding shutters of horizontal member size 40mm x 18mm x

1.29mm (of Jindal Section No. 8947 @ Wt. of 0.456 Kg/mt), vertical

member of size 40mm x 18mm x 1.29 mm (of Jindal section no:

8949 @ Wt. of 0.456 kg / mt) with 5 mm th transparent bronze

colour tinted float glass with powder coated aluminum fittings and

fixtures and transparent silicon sealant glass fixing Including 18 mm

Granite Frame as per details etc.

26 Providing and fixing FRP frame size 125x65 mm and 35mm thick 11.49 Sq.mt 2019.98

FRP shutter with wood grain raised panneled design finish shutter

having extra reinforcement on sides & edges in Gel coat finish. The

core of the shutter & frame is to be filed up with injected

polyurethene foam done in situ alongwith embedded wooden pieces

for stiffening & also taking hinges & fintures. The whole FRP frame

& shutter is to be water proof weather proof, termite proof &

resistance to mild acid/alkali. Rates are to be inclusive of S.S

hinges with fastener sleeve & alluminium fixtures & fastenings.

27 Providing and fixing Louverd type ventilators with powder coated 1.62 Sq.mt 13733.98

aluminum fittings and fixtures and Blur glass fixing to Adjustable

louverds and black granite frame as per details and executed as per

directed by Engineer Incharge.

28 Providing and fixing M.S. grills of required pattern to 430.50 KG 128.27

wooden/Marble/Granite/Stone frames of windows etc. with M.S.

flats at required spacings and frame alround, square or round bars

with round headed bolts and nuts or by screws (A) Ornamentle Grill.

29 Providing and fixing M.S. grills of required pattern to 731.58 KG 264.62

wooden/Marble/Granite/Stone frames of windows etc. with M.S.

flats at required spacings and frame alround, square or round bars

with round headed bolts and nuts or by screws (A) Ornamentle Grill.

30 Providing and fixing rolling shutters of approved makemade of 80 31.92 Sq.mt 4546.01

mm wide M.S. laths inter-locked togetherthrough their entire length

and jointed together at the endsby end locks mounted on specially

designed pipe shaft withbracket plates, guide channels and

arragements for insideand outside locking with push-pull operation

including thecost of hood cover and spring etc. complete. (B)

Shuttershaving width 3.5 M. and above

31 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 148.50 Sq.mt 1451.16

mm(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand)

on new surface or fixing on existing flooring byadhesive material

including dismentaling of existingflooring and jointed with color

cement slurry includingfinised with flush pointing & cleaning the

surface etc.complete for light shade

32 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 7.68 Sq.mt 1432.78

(average) base of cement mortar 1:6 (1 cement: 6 coarse sand) on

new surface or fixing on existing flooring by adhesive material

including dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing & cleaning the

surface etc. complete for antiskit.

33 Providing and laying Marbo Grenite tiles 8 to 10 mm thick , 24'' x 77.46 Sq.mt 1169.98

24'' in skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with white

34 Providing and laying polished Kota stone slab flooring over 20mm 49.26 Sq.mt 1069.62

(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse

sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete. (B)

It. No. Description of Item Quantity Unit Rate in Figure Total

35 Providing and laying 18 mm thick machine cut, free edges, machine 6.81 Sq.mt 3325.93

polished Black Granite tread and risers in single piece with 1 cm

nosing and necessary grooves on treads etc. complete.

36 Providing and laying BBCC of 75mm th. Layer in CM (1:3) including 252.72 Sq.mt 621.15

sparaying two coat of water proofing chemical with selected brand

by enginner incharge .i.e.perma or other with leveling complete for

ready base of china mosaic tratment.

37 Providing and laying broken china mosaic flooring for terrace using 245.43 Sq.mt 765.97

12 mm to 20 mm broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be tempered to bring

mortar creme out upto surface using white cement including

rounding off junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

38 Providing and cement vata (10cm x 10cm size) quarter round in 79.86 Rmt 24.28

cement mortar 1:1 including neat cement finishing watering etc.

39 Providing 15mm thick cement plaster in single coat on Rough 669.72 Sq.mt 171.21

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii) Cement mortar

1:4 (1-cement :4-sand) (Interior Plaster)

40 Providing 15 mm thick cement plaster in single coat on 208.14 Sq.mt 196.64

brick/concrete walls for interior plastering upto floor two level and

finished even and smooth in (i)Cement mortar 1:4 (1-cement:4-

sand) (ceiling Plaster)

41 20mm thick sand faced cement plaster on walls upto height 10 965.33 Sq.mt 337.52

metres above ground level consisting of 12mm thick backing coat of

C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M.

1:1 (1-cement : 1-sand) etc. complete.

42 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 12.60 Rmt 42.02

43 Applying two coats of Birla or Asian acrylic lappy (putty) and two 610.86 Sq.mt 40.59

coats of primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter and

sand papered smooth. ( Interior Wall Putty)

44 Applying two coats of Birla or Asian acrylic lappy (putty) and two 208.14 Sq.mt 42.72

coats of primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter and

sand papered smooth. (Ceiling Putty)

45 Wall painting two coats with plastic emulsion paint of approved 610.86 Sq.mt 80.87

brand and manufacture on wall surfaces to give an even shade

including throughly brushing the surface free from mortar droppings

and other foreign matter and sand papered smooth. (Interior Wall

46 Finishing wall with weather proof exterior emulsionpaint on wall 965.33 Sq.mt 117.40

surface (two coats) to give an requiredshape even shade after

thoroughly brushing the surfaceto remove all dirt, and remains of

loose powdered materials.etc complete (Exterior Wall Paint)

47 Wall painting two coats with plastic emulsion paint of approved 208.14 Sq.mt 83.00

brand and manufacture on wall surfaces to give an even shade

including throughly brushing the surface free from mortar droppings

and other foreign matter and sand papered smooth on ceiling.

(Ceiling Paint)

48 Providing laying and jointing in true line and level 40mm dia. 33.00 Rmt 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE /SUPREME/ ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be concelled

as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost

of all materials.

It. No. Description of Item Quantity Unit Rate in Figure Total

49 Providing laying and jointing in true line and level 32mm dia. 72.00 Rmt 119.15

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be concealed

as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost

of all materials.

50 Providing laying and jointing in true line and level 15mm dia. 39.00 Rmt 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be concealed

as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost

of all materials.

51 Providing and fixing concealed center point to wall ceiling & floor 24.00 Rmt 660.58

CPVC (SDR 13.5) PIPE having National SanitationFoundation

(NSF) seal for potable water of following dia. nominal bore tube

fittings and clamps including making goodthe wall, ceiling and floor

etc.complete. [F] 50mm.

52 Providing and fixing concealed center point to wall ceiling & floor 36.00 Rmt 253.82

CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube

fittings and clamps including making good the wall, ceiling and floor

etc. complete. [C] 25 mm.

53 Providing laying and jointing in true line and level 110 diameter 81.00 Rmt 856.03

U.P.V.C. SWR Type B pipe confirmng to IS 13592-1992 with one

end plain and other end socketed with rubbering, & fitting

conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointd with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC clamp of the size

110 mm diameter x 149 mm length x 145 mm high at every

mm center to center or shall be concealed in walls as directed

including necessary fittings such as Cowel vent, bends, shoes etc.

including testing of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

54 Providing and fixing screw down bib taps of following size.(A) Brass 12.00 Nos 214.81

screw down bib tap polished bright. (ii) 20mm dia.

55 Providing and fixing pillar tap, capstan head, screw down high 6.00 Nos 354.69

pressure with screws, shanks and back nuts. (ii) 20mm dia.

56 Providing and fixing chromium plated brass half turn flush cock of 9.00 Nos 263.77

approved quality including fixing in pipe line etc. complete.(ii) 25mm

57 Providing and fixing Gun metal check or non return full way wheel 6.00 Nos 663.43

valve.40 mm dia.

58 Providing and fixing Gun metal check or non-return fullway wheel 9.00 Nos 420.63

valve. (C) 25mm dia.

59 Providing and fixing Granite of 18 to 20mm thick having minimum 3.00 Nos 9511.17

single plece length of 210mm to be fixed on Walls to act as Study

Table / Wash Basin, including fixing the same using cement mortar

in proportion 1:1 etc. comp, Necessary Grove in Walls By Machine,

Front Side Round the edge and cutting hole in ganite stone for

wash basin, Computer Wire, including rubbing and polishing

finishing jointed with grey cement slurry including rubbing and

polishing finishing etc complete. etc complete.. with all labour &

material & equipment.....etc. Completed as directed by Engineer-in-

charge (A) Granite slab 18mm thick

60 Providing and fixing C.P.Brass towel rail complete with C.P.Brass 6.00 Nos 616.42

brackets fixed to woodenplugs with c.p.brass screws.(B) 600 mm x

61 Providing and fixing C.P. brass shower rose with 15mm or 20mm 3.00 Nos 282.16

inlet.(A) 100mm dia. Each

62 Providing and fixing 600mm x 450mm bevelled edge mirrror of 3.00 Nos 854.58

superior glass mounted on 6mm thick A.C. sheet or plywood sheet

and fixing to wooden pluge with C.P. brass screws and washers.

It. No. Description of Item Quantity Unit Rate in Figure Total

63 Providing and laying wash down water closet (european type Wall 3.00 Nos 10261.60

Hung WC pan) Florentine series FLS-WHT 0111B including

providing and fixing metropole Flush cock seat cover, jet wash etc

complete unit of jaquar Branch (or equvalant) including installing

and fitting as per manufacturers standards by skilled trained

plumber including testing etc complete quality and brand as

approved by Engineer in charge.

64 Providing laying and jointing in true line and level 160 diameter 42.00 Rmt 834.38

U.P.V.C. SWR Type B pipe confirmng to IS 13592-1992 with one

end plain and other end socketed with rubbering, & fitting

conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointd with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC clamp of the size

160 mm diameter x 210 mm length x 196 mm high at every

mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent cement

including cost of all materials.

65 Providing and fixing PVC SWR Nahni trap IS 14735 fordrain - 100 21.00 Nos 572.32

mm diameter with jali of the followingnominal diameter of self

cleansing design with C.I screaddown or hinged grating including

the cost of cutting andmaking good the walls.

66 Providing and laying (two level or slopes ) and jointing with stiff 21.00 Rmt 312.76

mixture of cement mortar in proportion 1:1 salt glazed stone ware

pipes following nominal internal diametre including testing of pipes

and joints etc complete. 150 mm dia.

67 Constructing brick masonary chamber for under ground 6.00 Nos 2932.93

C.I.inspection chamber and bends with bricks having crushing

strength not less than35 kg/sq.cm in C.M.1:5 C.I.cover with frame (

light duty) 455 mm x 610 mm internal dimension total weight of

cover with frame to be not less than 38 kgs.(weight of cover 23 kg

and wt.of frame 15 kg)R.C.C.top slab with 1:2:4 mix ( 1 cement:2

coarse sand:4 graded stone aggregates 20 mm size)

foundationconcrete 1:5:10 inside plaster 15 mm thick cement mortar

1:3 finished smooth with a floating coat of neat cement on wall and

bed concrete etc complete.(I) Inside dimensions 455 mm x 610 mm

and 450 mm deep for single pipe line.

68 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2- 3.00 Nos. 11042.74

coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat

of neat cement and making channels in cement concrete 1:2:4 mix

(1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside

size900mm x 1200mm and 1.5M. deep including C.I. cover with

frame size 560mm diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

Kg.)(A) With 230mm thick walls of brick msonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5

(1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm

diameter sewer.

69 Providing erecting and fixing double coated Syntex or equivalent 4500.00 Litre 3.95

PVC. (ISI) mark water tank of reqd capacity each with all necessary

fittings & connection etc. comp on terrace.

70 Providing and fixing ball cock of approved quality as directed.(A) 3.00 Nos 132.89

Copper metal(i) 25 mm dia.

71 Providing and laying sandwich type kitchen platform of size 2.10 9.81 Sq.mt 23691.57

x0.76 x 0.76 m and respected length with dhar polish or moulding

having base 4" and spport & base with marble or Kota as per site

requirement also loft and base finish with glaze tile and top with

selected shed of marble or granite with gas pipe provision and sink

including all fittings ,material and labour as per directed by engineer

It. No. Description of Item Quantity Unit Rate in Figure Total

72 Providing & Fixing Co2 type portable ABC Dry Powder Type ABS 9.00 Nos 3535.00

Fire Extinguisher Capacity 4.5 Kg. Discharge Range 3mt. Timing

to 180 Sec. standard approved IS code No. 2878:2004

73 (B) Providing sock pit of 5.00 Cu.M. Volume includingexcavating 3.00 Nos 3427.65

and filling brickbats with dry masonry workat top for 45cm. height

including covering the top withstone including providing vatas in

C.M. 1:3 with finishing curing etc. complete as directed.

74 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking 394.28 Sq.mt 704.07

concrete block 60mm thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design

Confirming to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line and level as per

guidlines of IRC : SP 63-2018 etc. Complete.

75 Providing and fixing pre-cast concrete kerb stone of gray cement 41.18 Rmt 370.68

based concrete block 30cm length,30cm height and 15cm thick of

M250 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with C:M

1:3 (1cement:3fine sand) etc complete

76 Providing and fixing eco-friendly light weight calcium silicate false 61.98 Sq.mt 1674.15

ceiling tiles having Tegular edge & 15 mm Thick Densified edges on

the Tile Periphery for Extra Strength The Light weight calcium

silicate ceiling tiles shall have , light reflection 85% non-combustible

as per B.S. 476 part IV, 100% humidity resistance and also having

thermal conductivity0.043° w/m KC.for the best thermal Insulation .

The Light weight calcium Silicate tile shall be of approved texture

Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe

having NRC value of 0.75 NRC or equivalent of size 595 X 595 mm

to be laid on true horizontal level suspended inter locking metal grid

of hot dipped galvanized steel sections (galvanizing @120 grams

per sqm including both side) consisting of main ‘T’ runner suitably

spaced at joints to get required length and size of 24X38mm made

from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and

cross ‘T’ of size 24X28mm made out of 0.33mm (Minimum) sheet

spaced 1200mm along spaced between main ‘T’ at 600mm centre

to centre to form agrid of 1200X600mm and secondary cross ’T’ of

length 600mm and size 24x28mm made of 0.30 mm thick

(Minimum) sheet to be interlocked at middle of the 1200X600mm

panel to form grid of size 600X600mm resting on periphery

walls/partitions on a perimeter wall angle pre-coated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the

help of rawl plugs at 450mm centre to centre with 25mm long dry

wall screws @ 230mm interval and laying 15mm thick Densified

edges light weight calcium silicate ceiling tiles of approved texture

(Fine Fissured/Cosmos/Spintone) in the grid including, cutting

/making opening for services like diffusers, grills, light fittings,

fixtures, smoke detectors etc.,

wherever required, Main ‘T’ runners to be suspended from ceiling

using G.I. slotted cleats of size 25X35X1.6mm fixed to ceiling with

12.5mm dia and 50mm long dash fasteners, 4mm G.I. adjustable

rods with galvanized steel level clips of size 85X30X0.8mm, spaced

at 1200mm centre to centre long main ‘T’ bottom exposed with

24mm of all T-sections shall be pre-painted with polyester baked

paint, for all heights, as per specifications, drawings and as directed

by engineer-in-charge.Note:- Only calcium silicate false ceiling area

will be measured from wall to wall. No deduction shall be made for

exposed frames/opening (cut outs) having area less than 0.30 sqm.

The calcium silicate ceiling tiles shall have NRC. Value of

(Minimum) for Fine fissured/Spintone/Cosmos and 0.75 NRC for

Globe, light reflection 85% non-combustible as per B.S. 476 part IV,

100% humidity resistance and also having thermal conductivity.

0.043° w/m KC.for the best thermal Insulation

It. No. Description of Item Quantity Unit Rate in Figure Total

77 Painting lines, deashes, arrows, letters etc on roads, Air fields,on 35.60 Sq.mt 126.21

walls and like in two coats with road marking paint, brushing

including cleaning the surface of all dirt, dust and other foreign

matter. (i) Upto 10cm in width

78 Clearing and grubbing road land including uprooting rank vegetation 0.21 Hact. 82249.89

grass bushes, shrubs, sapling and trees girth up to 300 mm

removal of stumps of trees cut earlier and disposal of unserviceable

materials (A) By manual means in area of light jungle

79 Provinding and laying controlled cement concrete M -250 and 1.67 Cu.mt 4845.98

finishing smooth with curing etc complete, including the cost of

formwork but excluding the cost of reinforcement for R.C.C. work in

(A) Foundations, footings, Base of Columns and Mass concrete.

80 Providing, fixing and erecting steel shed including M.S. G.I. pipe 90.82 Sq.mt 2434.02

(class-B), framing of structure with hollow section And painting with

two coats of oil paint including priming coat. Rates including with

necessary fabrication work including cutting, welding, making holes

by drilling machine & fixing in line and level of all structure including

cost of all laboures, fixtures, fastening and equipments etc.

81 Office Table:- 18mm thick three layer pre laminated particle board 3.00 No. 23230.00

Work with PVC Edge band 2mm thick wrapped around the top,

Decorative aluminium bidding in top and modesty including all

necessary elements with necessary features and fastning finish all

as per directed by Engineer in Charge. 6FT Office Table

(Dimension :- 180 cm x 90cm x 75 cm) with suitable Brand.

82 Revolving Chair:- Full-Back Executive Office Chair upholstered in 3.00 No. 14897.50

bonded leather and PVC, Padded seat and back for all-day comfort

and support, Pneumatic seat-height adjustment; 360-degree swivel;

smooth-rolling casters and having overall dimension 73.9D x 66.5W

x 115.6H Centimeters with Armrest (Brown) with selected brand.

83 File Rack:- lack Adjustable 5-Shelf Shelving Unit Storage Rack 9.00 No. 7777.00

Utility Rack Garage Shelves Display Rack Steel Boltless Rivet

Rack, 60 inches Height 1-Pack ({5 - SECTION } 5'[H] X 2'[L] X

1'[D]) with suitable Brand.

84 Steel Stool:- Office Stainless Steel Stool having minimum oveall 15.00 No. 1818.00

dimension 35.6D x 35.6W x 76.2H Centimeters, made with S.S. leg

and rubber pad/bushing with suitable Brand which will select by

enginner in charge.

85 Chair:- S.S. Chair for Office having seat and back with selected 12.00 No. 2626.00

cushion, Fabric, Pattern, PU with arm rest and minimum overall

dimension 78.7D x 41.9W x 78.7H Centimeters with suitable Brand

which will select by engineer in charge.

86 Stainless Steel Office Almirah :Suppliny and instaling Portable 3.00 No. 15150.00

Modern double Door steel almariah with nearer 30 kg wt having

diamension 36 x 18 x 78.5 inch made from ss,Eco friendly and UV

resistant in grey color having min 4 partioin for file rack and other

copartment as per selected and directed by Engineer incharge.

87 Providing and fixing Precast RCC Compound Wall made of I shape 200.30 Rmt 2171.50

verticle Pre cast Pre tension post of size 2100 mm height , section

150 mm x 150 x 50 mm center slot and edge chamfer made from

concrete grade M-25 (For Vertical Post), 2135 mm x 300mm x

mm plank made of pre cast and pretension from concrete grade M-

25 with 3 nos of 4mm tension wire and Edge 10 x 10 mm chamfer

(For Panel)7 panel in row position having center to center space not

more than 2.25 meter and segemnt height made of 2100 mmasper

design or as per directed by engineer incharge.

88 Providing and fixing ms grill entarnace gate of predetermine design 18.90 Sq.mt 4749.02

including all material like hinges,roller,stopper ,rail head , handle etc

having coat of red lead and painting with selected colour guide by

engineer incharge.

It. No. Description of Item Quantity Unit Rate in Figure Total

89 Providing and laying controlled cement concrete M.250 and curing 6.08 Cu.mt 8780.94

complete including the cost of formwork and Excluding the cost fo

reinforcement for reinforced concrete work in (D) Columns, Pillars

posts and struts, upto floor two level.

90 Providing and laying burnt brick masonary for super structure with 12.70 Cu.mt 4428.08

ordinary portland cement mortar 1:5 proportion including providing

scaffolding racking out joints curing etc. complete for all leads and

lifts. (Conventional Bricks) upto floor two level.

91 Providing and laying and fixing 50 mm thick expansion joint by 3.38 Sq.mt 1491.03

hydro cell semi rigid UV resistance with high performance laminated

closed cell polythene foam joint filler in sheet foam as directed, etc.

ELECTRIFICATION

92 Point wiring for Light/ Bell with 2-1.5 sq.mm & earthwire of 1.5 30.00 Pt. 449.45

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of pipe to be

erected concealed in/ on surface on wall/ceiling complete with 6A

Modular type switch/ bell push & accessories and earth continuity

of following type, erected on PVC / Metallic box, single mounting

base frame covered with textured/metallic front plate modules

erected on/ in wall/ ceiling as per pipe erected, with necessary

Lamp holder/ ceiling rose/ H.D.Connector as directed. (a) with

medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling completeCat-III

93 Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm 15.00 Pt. 638.32

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling complete with 6A Modular type

switch and hum free EME four or more step type electronic fan

regulator with separately mounted and accessories with earth

continuity of following type erected on PVC / Metallic box, single

mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed. (a) with

medium class Rigid PVC pipe and accessories, Cat-III

94 Point wiring for Looped Plug with 6A Modular type switch & 5 pin 15.00 Pt. 257.55

socket erected on PVC / Metallic box, single mounting base frame

covered with textured / metallic front plate modules erected on / in

wall / ceiling with following type accessories, Cat-III

95 Point wiring for Individual Plug with & earthwire of 1.5 sq.mm 15.00 Pt. 711.04

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic box covered

with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories. [II] For 16A Plug

with 2-2.5 sq.mm Cu. Wire, (a) with medium class Rigid PVC pipe

and accessories erected flushed on wall/ceiling complete, Cat-III

96 Providing & erecting Switch board for Computer or electric 12.00 Nos. 1133.22

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug [B] For Modular Type Accessories, Cat-III

97 Providing and erecting Mains with 1.1 KV grade FRLS PVC 150.00 Mtr. 82.82

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size , (a) with medium

class Rigid PVC pipe and accessories, (b) 2 wire 2.5 mm²

It. No. Description of Item Quantity Unit Rate in Figure Total

98 Supplying and erecting Flexible PVC insulated multi strand multi 18.00 mtr 77.77

core 1.1 kv grade ISI marked copper wires of following size to be

erected as directed.(h) 2.50 Sq.mm 3 core round PVC sheathed

99 providing and erecting Mains with 1.1 KV grade FRLS PVC 30.00 mtr 260.58

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with medium class

Rigid PVC pipe and accessories (h) 4 wire 6 sq. mm

100 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 24.00 Nos. 535.30

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V

to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)),(A) Tube Light with integral/ non-

integral driver, (v) 36-40 Watts, Surge-2 KV, IP-20, conventional

101 Supplying and erecting led lamps with following wattage capacity of 3.00 Nos. 112.11

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with

PC diffuser suitable LAMP holder (ii) 5 to 8 watts CAT-III

102 Providing and erecting Approved make Ceiling fan with double ball 15.00 Nos. 1596.81

bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm.

sweep complete, canopy erected on existing hook or clamp with

earthing. [Make shall be approved by Engineer in charge]]

103 Supplying and erecting 19/20 mm. nominal bore Medium Class M.S. 15.00 Mtr. 108.07

Pipe down rod erected duly painted for fan complete with necessary

24/ O.20, 3 core flexible wire with earthing.

104 Supplying & erecting approved make low noise decorative exhaust 3.00 Nos. 1703.87

fan having square frame ABS body with inbuilt lowers & square

frame.200mm with 1350RPM Cat.II

105 providing and erecting Miniature circuit breaker single pole 6A to 36.00 Nos. 112.11

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark CAT-III

106 Providing and erecting Sheet Steel powder coated MCB distribution 3.00 Nos. 2339.16

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should

be used of same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type outgoing Per

phase isolation type (PPI) (b) sheet steel double door (i)4 way

107 Providing & erecting 415 V MCB Four Pole for Motor & Inductive 3.00 Nos. 668.62

Load (C Curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity (b)40 Amp., Cat-III

108 Providing & erecting 240 V MCB double pole switch for lighting 3.00 Nos. 299.97

Load (B Curve) having 10 KA breaking capacity & confirms to IS :

8828 in existing box having following capacity CAT-III (a)6 to 32 A

109 Plastic enclosure fitted with DIN rail suitable for incorporating One / 3.00 Nos. 52.52

It. No. Description of Item Quantity Unit Rate in Figure Total

110 Aproviding and erecting Approved make RCCBs conforming to IS: 9.00 Nos. 1969.50

12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic component. for

following Max. rating erected as directed (i) 25 Amps., Cat-III

111 Supplying & erecting earth pit of minimum bore dia.150mm size 3.00 Nos. 4591.46

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report must

be submitted by Agency. (a) For Electrical Installation up to 440V in

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

112 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 66.00 mtr 153.52

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

cables(A) 4 core 16 Sq. mm

113 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 159.00 mtr 92.92

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables. (B)

114 Providing and, fixing heavy duty flange type brass cable gland with 36.00 ea 38.38

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables. (B) 2 to

115 Supplying and erecting LED street light / Flood light fittings with 18.00 Nos. 3345.12

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor

more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver

efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.), (A) Street Light

(IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (i) above 36 to

116 Providing and erecting Miniature circuit breaker single pole 0.5A to 18.00 Nos. 270.68

2A system and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

117 Supplying & erecting approved make SMC press moulded 18.00 Nos. 476.72

composite FRP. loop-in, loop-out approx. 2mm thick box complete

with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting

mob & hinged doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps& earth bolt of

following size of box..( c)150mm x 125mm x 100mm [deep]

It. No. Description of Item Quantity Unit Rate in Figure Total

118 Providing and erecting Street Light pole bracket comprising main B 18.00 Nos. 614.08

Class GI pipe of 4.2 cm/require outside dia. complete with suitable

B Class G.I. sleeve tubing of approx. 45cms.length and suitable for

76.5 mm /80mm / required size of pole top having sufficient

fasteners for fixing the brackets and having spread of 1.5.mtr.

length with 110 deg.with vertical plane & suitable welded stays,

reducer and with check nuts complete painted with one coat of Red

oxide / PU base primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket 1 Mtr

Replacing old & u/s Solder less crimping type Aluminium lugs

conforming to IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

121 Solder less crimping type Copper lugs conforming to IS suitable for 18.00 Nos. 8.08

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. . (A) 1.5/2.5 to 6 Sq.mm

122 Providing and erecting Approved make Four pole moulded case 3.00 Nos. 6790.43

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.with enclosure

123 Supplying KITKAT pattern porcelain cut-out fuse with base of 9.00 Nos. 278.76

following current capacity erected on existing block board. (v)

A. 500 V. cat-iii

124 Supplying and erecting nuwood 12mm thick on existing angle iron 3.00 Sqmtr 385.82

frame or wooden patti

125 Providing & laying approved make Double walled corrugated pipes 60.00 mt 62.62

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth in

existing trench for laying of cable. below ground / road surface for

enclosing cable 50mm

126 Making trench in soft soil of suitable width of 90 cm deep for laying 54.00 mt 55.55

cable or locating the fault all over the run and back filling the same

and making the surface as normal ground.

Rs. Ninety Eight Lakhs, Fifty Six Thousand Three Hundred Twenty Four and Seven Paisa Only

I/We am/are willing to carry out the work @ ______________ % ______________ percent

(should be written in figures and words) below / above, the estimated rates mentioned above, amount of

my/our tender works out as under :

Above all items of "Bill of Quantities" with Item Description, Unit, Qty, Rate & Amount have verified by me and

It. No. Description of Item Quantity Unit Rate in Figure Total

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the

Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills.

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

5 The contractor will have to submit the mix design for different grades of cement concrete and asphalt

at his own cost before execution as directed and to be approved from the engineer in charge.

6 Dismentaling Credit Rs.15,000/- (Fifteen Thousand) only shall be recovered from contractors R.A.

Deputy Executive Engineer Executive Engineer

District (R&B) Sub Dn. No.1 District (R & B) Division

Vadodara Vadodara