Thuruthikkattu cheruvallikkavu devaswom - aymanam sub group - kottayam group-construction of sreekovil for goddess vandurga and sree bhadrakali

GSB Laying for sreekovil base area (Bhadra & Vanadurga)

Granular Sub-base with Well Graded Material (Table 400.1) <br> (A) By Mix in Place Method <br> Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. <br> (i) For Grading I Material

Sreekovil for Bhadra

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry in cement mortar 1:6 (1 cement : 6 coarse sand) with hard stone in foundation and basement up to plinth level

Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15 up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement :1.5 coarse sand(Zone III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Stone work ashlar paved in c.m 1:6 ( 1 white cement: 6 coarse sand) moulding pointing with cement mortar 1:2 ( 1 cement: 2 stone dust) with an admixture of pigment matching to stone shade using white sand stone one face dressed and providing extra ornamental works etc.

Extra charges for forming, Supplying and providing Kumudam of required size and shape (Round) in brick masonry as per plan

Extra charges for forming , supplying and providing vedika of required size and shape in brick masonry as per plan

Extra charges for forming , supplying and providing corner pillars of required size and shape in brick masonry as per plan

Extra charges for forming , supplying and providing Ghanadwaram of required size and shape in brick masonry as per plan.

Extra charges for forming , supplying and providing Kallutharam, valaru, kapodham of required size and shape in brick masonry as per plan.

Reapering with reaper of size 38x16 mm with cement mortar 1:4 of suitable spacing including all cost of materials and labour charges.

Roofing with PWD pattern tiles (R.P Tiles)

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Polishing on wood work with ready mixed wax polish of approved brand and manufacture:New work

Providing Teak Wood Double Leaf Shutters 50 mm thick planks and providing soothrappattika having a sectional area of 100 mm x75 mm size ornamental works like flowers having brass kumila each leaf 2 nos iron flats 40x6 mm size top and bottom and having all ornamentation etc. complete

Supplying and fixing MANICHITHRATHAZHU (16 Inch) for Valiyambalm main door and providing locking arrangements.

Supplying and fitting COPPER THAZHIKAKKUDAM including all ornamentation and polishing with lacquer polish etc complete (sanctioned rate)

Providing and laying new ashlar slabs (Krishnashila ) for flooring inside having thickness of 100 mm over C.M 1:4, 20 mm thick with proper slopes as directed by the departmental officials.

Sreekovil for Vanadurga

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry in cement mortar 1:6 (1 cement : 6 coarse sand) with hard stone in foundation and basement up to plinth level

Providing and laying in position ready mixed or site batched design mix cementconcrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15 up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement :1.5 coarse sand(Zone III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Stone work ashlar paved in c.m 1:6 ( 1 white cement: 6 coarse sand) moulding pointing with cement mortar 1:2 ( 1 cement: 2 stone dust) with an admixture of pigment matching to stone shade using white sand stone one face dressed and providing extra ornamental works etc.

Extra charges for forming, Supplying and providing Kumudam of required size and shape (Round) in brick masonry as per plan

Extra charges for forming , supplying and providing vedika of required size and shape in brick masonry as per plan

Extra charges for forming , supplying and providing corner pillars of required size and shape in brick masonry as per plan

Extra charges for forming , supplying and providing Ghanadwaram of required size and shape in brick masonry as per plan.

Extra charges for forming , supplying and providing Kallutharam, valaru, kapodham of required size and shape in brick masonry as per plan

Reapering with reaper of size 38x16 mm with cement mortar 1:4 of suitable spacing including all cost of materials and labour charges.

Roofing with PWD pattern tiles (R.P Tiles)

Polishing on wood work with ready mixed wax polish of approved brand and manufacture:New work

Providing and laying new ashlar slabs (Krishnashila ) for flooring inside having thickness of 100 mm over C.M 1:4, 20 mm thick with proper slopes as directed by the departmental officials.

Supplying and fixing MANICHITHRATHAZHU (16 Inch) for Valiyambalm main door and providing locking arrangements.

Supplying and fitting COPPER THAZHIKAKKUDAM including all ornamentation and polishing with lacquer polish etc complete (sanctioned rate)

Providing Teak Wood Double Leaf Shutters 50 mm thick planks and providing soothrappattika having a sectional area of 100 mm x75 mm size ornamental works like flowers having brass kumila each leaf 2 nos iron flats 40x6 mm size top and bottom and having all ornamentation etc complete.