RECONDUCTORING AND DRAWING ADDL FEEDER ON EXISTING TOWN FEEDER BY USING CC FROM OTP SS TO TOWN

Dismantling (without damage) one km 11kV line (three conductors) including dismantling cross arm, insulators, disc, disconnecting jumper connection, rolling the conductor and stacking the materials.

Labour charges for loading HT A type pole from the stacking place and unloading the same at work site (transportation by any vehicle).

Renewal of existing damaged/old 11kV PSC/RCC Pole with new A type pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole.

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 numbers of poles excluding loading& unloading charges.

Additional rate for excavation of Pit for A type pole in Laterite.

Additional rate for excavation of Pit for A type pole in Hard Laterite.

Additional rate for excavation of Pit for A type pole in Soft Rock.

Additional rate for excavation of one Pit for HT Pole/HT Stay in Laterite.

Additional rate for excavation of one Pit for HT Pole/HT Stay in Hard Laterite.

Additional rate for excavation of one Pit for HT Pole/HT Stay in Soft Rock.

Additional rate for excavation of one Pit for LT Pole/LT Stay in Laterite.

Additional rate for excavation of one Pit for LT Pole/LT Stay in Hard Laterite.

Additional rate for excavation of one Earth Pit (2.5m depth) in Laterite.

Additional rate for excavation of one Earth Pit (2.5m depth) in Hard Laterite.

Additional rate for excavation of one Pit for Coil Earthing in Laterite

Additional rate for excavation of one Pit for Coil Earthing in Hard Laterite.

Dismantling of 11 kV Aerial bunched cable XLPE insulated of size 3 x 120+ 1 x 95 sqmm with bare insulated Messenger

Dismantling one suspension clamp from 11 KV ABC

Dismantling one Anchor clamp /dead end clamp from 11 KV ABC

Dismantling of suspension clamp suitable for LT AB cable

Dismantling of Anchor clamp / dead end clamp for LT AB cable

Dismantling of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16 (Street Light) + 1 x 50 Sq.mm. (Insulated Messenger)

Dismantling (without damage) one 11kV A type pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged 11kV A type pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling (without damage) one 11kV PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged 11kV PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged 11kV TW/RSJ/Rail pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling (without damage) one HT PSC/RCC Strut pole including removal of clamps and stacking.

Dismantling (without damage) one V cross arm/Channel cross arm from existing Pole and bringing back to section store.

Dismantling (without damage) one Channel cross arm from existing DP structure and bringing back to section store.

Dismantling (without damage) one AB switch from existing structure and bringing back to section store.

Dismantling one damaged LT TW/RSJ/Rail pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged LT TW/RSJ/Rail Strut pole including removal of clamps and stacking.

Dismantling (without damage) one LT TW/RSJ/Rail Strut pole including removal of clamps and stacking.

Dismantling one damaged LT PSC/RCC Strut pole including removal of clamps and stacking.

Dismantling (without damage) one LT PSC/RCC Strut pole including removal of clamps and stacking.

Dismantling one LT 2 line cross arm with clamp from existing pole and stacking.

Dismantling one LT 4 line cross arm with clamp from existing pole and stacking.

Dismantling single phase WP service connection with meter & all accessories and bringing back to section store.

Dismantling three phase WP service connection with meter & all accessories and bringing back to section store.

Dismantling (without damage) one km LT single phase 2 wire OH line conductor by dismantling cross arms, insulators and stacking the conductors in rolls properly.

Dismantling (without damage) one km LT three phase 4 wire OH line conductor by dismantling cross arms, insulators and stacking the conductors in rolls properly.

Dismantling (without damage) one km LT additional conductor line by dismantling cross arms, insulators and stacking the conductors in rolls properly.

Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires.

Fitting and erecting one HT A type Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing).

Fitting and erecting one HT Double Pole Structure using A type pole in position including fitting 2 No. channel cross arm, digging and back filling pit in ordinary soil, drawing sufficient length of GI earthing leads through all cross arms to the ground for earthing (excluding provision of earthing).

Fitting and providing one HT Stay for 11kV pole, including digging and back filling pit in ordinary soil.

Fitting and providing one Strut using A type pole, including digging and back filling pit in ordinary soil.

Fitting and providing one Strut using HT PSC pole including digging and back filling pit in ordinary soil.

Fitting and providing one HT Fly stay for 11kV pole using HT PSC pole including digging and back filling pits in ordinary soil, drawing sufficient length of GI earth leads to the ground for earthing (excluding provision of earthing).

Fitting one additional Fuse unit and giving connection from Transformer to fuse and Distribution box to LT OH line.

Stringing of 11 kV Aerial bunched cable of size 3 x 120 + 1 x 95 sqmm with bare/insulated Messenger through existing poles

Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50 sqmm with bare/insulated Messenger through existing poles

Erection of Anchor clamp / dead end clamp for 11kV ABC of any size

Erection of suspension clamp for 11KV ABC of any size

Erection of Anchor clamp / dead end clamp for LT ABC of any size

Erection of suspension clamp for LT ABC of any size

Providing Cable Tie

Installation of Insulation piercing connector for main to service line main :16-95 sqmm, Tap : 4-35 sqmm

Installation of Insulation piercing connector for main to service line main :16-95 sqmm, Tap 16-95 sqmm

Providing End Caps

Additional rate for providing one disc set, PG clamp etc. complete, on any type of HT pole for making cut point.

Renewing one damaged PSC/RCC Transformer DP structure with a new A type Transformer DP including excavation, dismantling accessories like AB switch, DO fuse, LA, LT fuses, HT, LT and earth connections, dismantling existing Transformer, keeping it in safe custody and re erecting all accessories including Transformer on the new DP as per standards and drawing sufficient length of GI earthing leads to the ground for earthing, excluding renewal of pipe earthing.

Additional rate for refitting/redoing one Disc set while renewing any type of 11kV cut pole.

Stringing of one km 3 PH 11kV line with XLPE Insulated ACSR Raccoon or equivalant (3 conductors) after fitting insulators, binding conductors to pin insulators using suitable tie and anchoring with wedge type anchoring clamps including cutting and removing tree branches wherever necessary excluding cut point works.

Straightening one slanted 11kV Cut pole after lowering down the existing line and stringing the line after work.

Straightening one slanted LT Cut Pole after lowering down the existing line and stringing the line after work.

Stringing, shackling, fitting cross arms, insulators and binding, giving jumper connection etc. using ACSR Rabbit for Phase and ACSR Weasel for Neutral & Street Main, for one km LT 3ph 5 wire line including cutting and removing tree branches wherever necessary and conveyance of all materials (except poles) from stacking place.

Additional rate for refitting/redoing one Shackle Set, including reshacling one span, while renewing any type of LT pole.

Renewal of existing damaged/old 11kV Stay with new stay in place including excavation & backfilling of pit, dismantling, refitting of all items and conveyance of all materials.

Renewal of existing damaged/broken old 11kV Stay to the existing stay rod.

Transporting poles by hired vehicle to a distance beyond 5km and carrying upto 4 numbers of poles. (Running km)

Providing Stay for LT poles including digging & back filling pit in ordinary soil.

Providing Strut using LT PSC pole including digging and back filling pit in ordinary soil.

Providing Fly stay for LT pole using LT PSC pole including digging and back filling pit in ordinary soil.

Installing One No. 4 way Satellite Connector of size Main :16 to 95, Tap:4 to 35 Sq.mm to the LT AB cable of Standard size

Installing One No. Insulation piercing connector of size Main :16 to 95 ,Tap:1.5 to 16 Sq.mm

Doing straight joint on HT XLPE UG cables of sizes beyond 3x185 sqmm and upto and including 3x300 sq mm using the cable jointing kit supplied departmentally as per specification after providing proper traffic signalling and caution board fencing etc. wherever necessary, including charges for cable jointer and other sundries etc. as per the direction of departmental officers at site.

Doing one cable end termination on HT XLPE UG cables of sizes beyond 3x185 sqmm and upto and including 3x300 sq mm using the cable jointing kit supplied departmentally after making fencing,caution board and all other safety measures including charges for cable jointer etc. complete as per the direction of the departmental officers.

Laying HT XLPE UG cable of sizes beyond 3x185 sq mm and upto and including 3x300 sqmm including conveying cable from Sub Regional Store/stacking place to work site and laying it carefully using cable rollers, taking through stone ware/G.I.pipes at road crossing/culverts/bridges etc. whereever necessary, providing identification tags at 5m intervals, filling the space around the cable with riddled soil and covering the top with bricks, providing cable route markers at 100m intervals, inclusive of cost of all materials (other than cost of GI/HDPE pipe & UG Cable), labour and transport including crane charges excluding excavation and backfilling.

Excavation of cable trench (soil surface) and digging out the faulty portion of the cable from the trench for redoing straight through joint, re-laying the cable after jointing, refilling and consolidating the trench as per standard specification. (excluding joining).

Horizontal Direct Drilling HDD 200 mm bore (110 mm HDPE Pipe ) Horizontal Direct Drilling along / accross roads, supplying and pulling 110 mm HDPE Pipe duct ( 3 core 3 X 300 mm² XLPE UG Cable including surveying the site for collecting information about under ground utility installations and other obstructions using suitable modern sensing equipments, pit making , pilot drilling, pre reaming, closing of pits with normal soil and consolidation or by any method as directed byroad authorities, without damaging other utility installations, providing HDD rroute markers at pit locations as per the direction of Dept Officers etc. Complete including cost of all material labour,hire and conveyance charges and submission of final profile drawing ( Measure ment will be taken only after cable laying )

Mounting and connecting HT XLPE UG cable ends of all sizes upto and including 3x300 sq mm with special type cable clamps, bolts, nuts, terminal protectors etc.including cost of extra materials if needed and giving necessary jumper connections.

Fitting one set AB switch on existing DP, giving connection and drawing sufficient length of GI earthing leads to the ground for earthing, excluding provision of earthing.

Fitting one Additional 75x40mm, 1.8m Channel cross arm in existing single pole including conveyance of materials.

Fitting one Additional 2.4m/3m Channel cross arm (100x50x6mm), in existing 11kV DP including conveyance of materials.

Fitting one Additional 2.4/3m Channel cross arm (75x40x6mm), in existing 11kV DP including conveyance of materials.

Fitting one LT 2 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line.

Fitting one LT 4 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line.

Insertion of one HT A type pole in existing OH line including digging & backfilling pit in ordinary soil, fitting cross arm, insulators, binding etc., drawing sufficient length of GI earth leads to the ground for earthing (excluding provision of earthing).

Dismantling one damaged AB switch from existing structure and bringing back to section store.

Conveyance of one km 11kV line materials from section store/stacking place to the work site (excluding poles).

Providing 11kV Jumper connection for one phase from OH line to Transformer through AB, DO and LA using Copper/ACSR conductor.

Please Enable Macros to View BoQ information