Development of Government Taluk Hospital Iritty in Kannur District Kerala State including all associated MEP Services and Utilities for Health and Family Welfare Department Govt. of Kerala

Amount

BoQ ABSTRACT : Please enter the Total amount of sheet BoQ 2 and Sheet BoQ3 in the respective columns

Total amount of Sheet BoQ2 (Civil, PHE works)

Total amount of Sheet BoQ 3 (MEP works)

Description of Work / Item(s)

Amount

EARTH WORK

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.10.1.1 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:All kinds of soilPipes, cables etc, not exceeding 80 mm dia

2.18.1 : Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete ( Measurements to be taken of the face area timbered):Depth not exceeding 1.5 m

2.18.2 : Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete ( Measurements to be taken of the face area timbered):Depth exceeding 1.5 m but exceeding 3 m

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

PILING WORK

od324596/2022_2023 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Minimum Cement content considered for pile concrete is @ 400 kg/ cum.Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used. 800 mm dia piles

od171875/2022_2023 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Minimum Cement content considered for pile concrete is @ 400 kg/ cum. Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used. 600 mm dia piles. 750 mm dia piles

od324960/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge. Single pile above 150 tonne and upto 200 tonne safe capacity: Routine test (Test load shall be 1.5 times the safe capacity)

od324961/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification and the direction of engineer -in-Charge. Single pile above 150 tonne and upto 200 tonne safe capacity: Initial test (Test load 2.5 times the safe capacity)

20.2A.1 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified,excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Minimum Cement content considered for pile concrete is @ 400 kg/ cum.Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

20.6.2.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityInitial test

20.6.2.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityRoutine test

CONCRETE WORK

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.1.4 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.12 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:31/2:9 (1 ordinary portland cement : 2 Fly ash : 31/2 coarse sand : 9 graded stone aggregate 40 mm nominal size).

4.1.13 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1: 21/2:4:11 (1 Ordinary portland cement : 21/2 fly ash: 4 coarse sand : 11 graded stone aggregate 40 mm nominal size)

4.2.5 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

4.12 : Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification .

4.19.1.1 : Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in-charge. Note : 1) Excess/less cement used than specified in this item is payable/recoverable separately. 2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS: 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS : 456-2000 in the items of BMC and RMC.All works upto plinth level :M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

4.19.1.2 : Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in-charge. Note : 1) Excess/less cement used than specified in this item is payable/recoverable separately. 2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS: 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS : 456-2000 in the items of BMC and RMC.M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

RCC WORK

5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.9 : Centering and shuttering including strutting, etc. and removal of form for:Arches, domes, vaults up to 6m span

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.18 : Centering and shuttering including strutting, etc. and removal of form for:Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.20 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.

5.34.2 : Extra for providing richer mixes at all floor levels.Providing M-35 grade concrete instead of M-25 grade BMC/RMC. (Note: Cement content considered in M-35 is @ 350 Kg/cum).Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

5.38 : Extra for R.C.C. /B.M.C/R.M.C. work above floor V level for each four floors or part thereof.

5.43.1 : Providing and fixing in position Stainless steel Grade 304 Plate 1.0 mm thick as per design for expansion joints.200 mm wide

5.44.2 : Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self – centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge . (Material shall confirm to ASTM 6063).Floor Joint of 150 mm gap.

5.45.2 : Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221-02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).Wall Joint of 150 mm gap.

5.46.2 : Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s preengineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. Material shall confirm to ASTM 6063.Roof Joint of 150 mm gap.

MASONRY WORK

50.6.1.1 : Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.6 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.1.1 : Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

6.4.2 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:6 (1 cement : 6 coarse sand)

6.5 : Extra for brick work/ AAC block masonry/Tile brick masonry in super structure above floor V level, for each four floors or part thereof by mechanical means.

6.15 : Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

6.32.1 : Brick work with clay flyash F.P.S. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor five level in:Cement mortar 1:4 (1 cement : 4 coarse sand)

6.34.2 : Brick work with non modular fly ash lime bricks (FALG Bricks) conforming to IS: 12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in:Cement mortar 1:6 (1 cement : 6 coarse sand)

6.38 : Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above floor 2 level up to floorV level in polymermodified adhesive mortar / cement mortar 1:4 (1 cement :4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6.47 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor Vlevel with RCC band at sill level and lintel level with approved block laying polymermodified adhesive mortar all complete as per direction of Engineer-in-Charge. (Thepayment of RCC band and reinforcement shall be made for seperately).

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

FLOORING

11.3.1 : Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

11.6.1 : Cement plaster askirting upto 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement .18 mm thick

11.20.3 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

11.27 : Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

od170762/2022_2023 : Providing and laying Antiskid Ceramic floor tiles 300x300x7 mm of Ist quality conforming to IS : 15622 of approved make,shade,and pattern laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.including cost and conveyance of all materials,labour charges,lead,lift etc, complete as directed by the Engineer-in-Charge at all levels.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.56.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.4.11 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.75 cm triangle

8.4.12 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.50cmx 60 cm rectangular (Single chevron etc.)

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

8.7.A : Providing and erecting overhead signs with retro reflectorised sign with 7 years warranty manufactured as per IRC67 made of Hign Intensity Micro Prismatic (Type IV ) grade sheeting fixed over corrosion resistant 2mm thick aluminium alloy sheet with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plansTruss and Vertical Support

8.10.2 : Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

8.11.2 : Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control Up to 10 cm in width

8.16 : Reinforced cement concrete M-15 grade boundary pillars of standard design as per IRC:25-19767, fixed in position including finishing and lettering but excluding painting .

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matchingshade complete.

od238914/2022_2023 : Extra for Providing grip grooves 3 nos 3mmx3mm in granite threads including cost and conveyance of all machinery,materials, labour charges, etc and making the sufrace clean complete at all levels as directed by the Engineer-in-Charge( Cost of granite slab will be paid separately )

od239180/2022_2023 : Providing fixing flooring transition profile at transitions between tile, vinyl and granite flooring of approved sizes and design as per manufacturer’s standard. The finish of the profile is Satin Stainless Steel of grade 304 (AISI 304) or as approved by the Engineer in charge . The profile is to be fixed with mortar or adhesive or screws as per manufacturer’s specification and as approved by the architect or client.

od239218/2022_2023 : Providing laying 2mm thick polyurethene reinforced laminated antistatic, antifungal, antibacterial vinyl flooring and skirting, including self levelling upto 3mm thick with cementitious material ,flexibility less than 20mm, residual indentation less than 0.1 mm electrical behaviour less than 2kV, of approved colour, size and texture over the floor surface to proper level, line using adhesives as per manufacturer's specification including joint treatment, coving cum pvc capping, welding etc complete as directed by the Engineer-in- Charge at all levels.The rate is inclusive of cost of all materials,upto 3 mm thick self levelling, welding all joints, labour, lead, lift etc. complete as directed by the Engineer-in-Charge at all levels

JOINERY & PARTITION WORK

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

od170771/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With high performance glass panes of 6 mm thickness meeting GRIHA compliance of overall value VLT 34%, SHGC 0.34.

od239900/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With toughened glass of 5.0 mm thickness

od238363/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With high performance glass panes of 6 mm thickness meeting GRIHA compliance of overall value VLT 40%, SHGC 0.45.

od238440/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With Toughened glass panes of 6 mm thickness

od238474/2022_2023 : Provided and fixing dusted/frosted glass film of make 3M/Avery Dennison or equivalent of approved shade (overall thickness of Film + Adhesive shall be approx. 120 microns) on glasswith customized prints with HP latex based high quality prints. The film shall install with self-adhesive and bubble-free installation to be done on clean glass .The rate shall include the cost and conveyance of all materials, labour charges, scaffolding, lead ,lift, sundries, print, wastage ,design, operations etc complete as directed by the Engineer in charge at all levels.

od238501/2022_2023 : Providing and fixing hardwares for Handicaped door(Excluding door frame and panel).The shutter to be provided with cylindrical knob lock with rose diameter 75 mm and SS matt finished kick plate of dimension 300 MM X 1050 MM X 1MM including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing etc. complete as directed by the Engineer-in-Charge at all levels:

od238702/2022_2023 : Providing and fixing of Hollow metal steel doors double leaf or single leaf made of pressed galvanized steel confirming to IS 277 with the following specification. Doors shall be with vision glass and louver as a part of complete assembly. Door frame shall be single rebate grooved profile of size 125 x 55mm made out of minimum 1.20mm (18gauge) thick galvanized steel sheet as per manufacturer recommendation. Frames shall be mitered and field assembled with self tabs. Frames to have inbuild grooved sealing system and shall be site fitted with PVC seal as standard. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frames shall be filled with puff / honey comb infill material. Door leaf shall be 46mm thick fully flush double skin door, with or without vision lite. Door leaf shall be manufactured from minimum 0.8mm (22guage) thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core/ equivalent material. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a clipon arrangement. The glass should be minimum 5mm clear toughened glass of relevant rating of the door. All doors and frames shall be finished Pure Polyester Powder coated and shall have passed minimum 500 hours of salt sprey test. Measurement shall be done in sqm area of door as per technical specification for payment irrespective of door sizes. Rate shall include supply and installation of door and hardware as a complete assembly including vision glass, louvers etc complete as mentioned in the door and hardware schedule complete as per manufacturer recommendation and as directed by Engineer in charge at all levels.

21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

21.11.1 : Providing and fixing stainless steel (SS 304 grade) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer - in-Charge complete.205 x 19 mm

21.12.2 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

21.13 : Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.15.1 : Supplying and fixing 200 mm Aluminium aldrop

21.15.2 : Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary necessary screws etc. complete.Powder coated minimum thickness 50 micron aluminium

21.17 : Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

9.21.1 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative Type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.62.2 : Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete:250x16mm

9.70.1 : Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:125x64x1.90 mm

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.92.1 : Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm

9.96.1 : Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:300x16 mm

9.97.1 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm

9.97.3 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

9.101.2 : Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

9.105.1 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS : 2095 : part I

9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm

9.105.4 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin non - asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

9.105.5 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurposecement bonded wood particle board manufactured as per IS: 14276 with suitablecement bonded board screws

9.114.1 : Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.119 : Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer-in Charge.

9.120.2 : Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of whicj 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mmx2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5 mm + 2 mm ) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer -in-charge, manufacture's specification & drawing.30 mm thick pre laminated PVC door shutters

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.2 : Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge.

9.126.1 : Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick.Marine plywood conformingto IS : 710

9.127.1 : Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Types S, including cost of adhesive of approved quality.1.5 mm thick

9.136 : Providing and fixing fire resistant door frame of section 143x57 mm having built in rebate made out of 16 SWG G.I. sheet ( zinc coating not less than 120 gm/ sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer -in-charge (Dash fastener to be paid for separately ).

9.139 : Providing and fixing panic bar / latch (Double point ) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer -in-charge, all complete.

9.142.1 : 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded solid PVC ( ±0.2 mm) thick, having styles & rails (except lock rail ) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinges side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm s 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge.Non decorative finish (matt finish)

9.158.1 : Providing and fixing in wall lining medium density fibre board IS: 14587: 1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.12 mm thick.

9.159 : Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickeled plated bright finishing M.S. piano hinge IS: 3818 marked with necessary screwed complete.

9.161 : Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontalside & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mmthick GI sheet ( Zinc coating not less than 120gm/m2) suita2ble for mounting 120min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineralwool Insulation having density min 96Kg/m2 . The frame will have a provision ofG.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style ofsize M10 x 80 ) suitable for fixing in the opening along with Factory madeTemplate for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire ratedglazed shutter . The frame shall be finished with a approved fire resistant primeror Powder coating of not less than 30 micron in desired shade as per thedirections of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded

9.162 : Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minFire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mmwide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet(zinc coating not less than 120gm/m²) duly filled mineral wool insulation havingdensity min 96 kg/m³ and fixing with necessary stainless steel ball bearing hingesof size 100x89x3mm of approved make, including applying a coat of approvedfire resistant primer or powder coating not less than 30 micron etc all completeas per direction of Engineer-in-charge (panelling to be paid for seperately

9.164 : Providing and fixing glazing in fire resistant door shutters, fixed panels & partitionsetc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mmfrom the edges and 150 mm c/c , including applying a coat of approved fire resistantprimer/powder coating of not less than 30 micron on G.I. beading, & special ceramictape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-incharge.The glass shall be clear, toughened, interlayered, non-wired fire resistant having11 mm thickness of approved brand with 120 minutes of fire resistance both integrity &radiation control (EW120) and minimum 15 min of insulation (EI15) and having a soundreduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category ofImpact Resistance as per EN 12600. The glass should be manufactured in UL & TUVaudited Facility and including UL-EU Certification.The maximum glazing size cannotbe more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report forthe complete system (Glazed Door or Partition) will be considered valid only if it containsthe stamp and signature of the authorized signatory from the glass manufacturer.(Actual glass size is to be measured at site for payments).

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

STEEL & ROOFING WORK

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.8.1 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.17 : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

12.1.3 : Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/m2

od239293/2022_2023 : Providing and Fixing Multi cell/tight cell polycarbonate sheet Panel System with16mm thick (minimum) single panel . The weight of the panel shall not be less than 3250 gram per square meter. Panel Width shall not be less than 1040mm to ensure best performance for wind uplift, vibration, oil canning and visual appearance. The panels shall be uniform in color with an integral Tight-Cell core. In a cross section, the core shall be constructed of tight cells not to exceed 4mm x 4mm. Panels shall be manufactured with Vertical Standing Seam at both sides of the panel. Snap-on connector to interlock the panels shall have a grip-lock tooth locking mechanism to ensure maximum uplift capability. Panels shall be secured with snap-on connectors with / without continuous double wall Aluminium spacer along the standing seam. Panel shall be factory sealed/end welded panels with additional End-cap/Aluminium U-Profile (mill finish) for ends. Panels shall be co-extruded UV protected. Panel shall be co-extruded with special anti glare compound to make it anti-glare/soft light to prevent glare and sun streaks. All aluminium sections to have recycled content of 15-30%.VLT>50% SHGC 0.27. The rate shall includes ,cost and conveyance of all materials,Handling of machineries and electrical charges etc. labour charges,lead,lift etc. complete as per technical specification and as directed by the Engineer in charge at all levels .The above work shall be carried out by an agency having sufficient experience in concerned work and should ensure a guarantee for any defective installation,material composition and water and weather tightness for a period of 10 years from the date of completion of the said work .only skilled and experienced persons shall be employed for this purpose.

CEILING WORK

12.24.3.1 : Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately):Flame retardant face insulating board 12 mm thick

12.27.4.1 : Extra for Circular cutting including wastages in ceiling with:Flame retardant face insulating board 12 mm thick

12.32 : Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling.Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling .

12.45.2 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum fire resistant board conforming to IS; 2095-Part I

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.47.2 : Providing & fixing UV stabilised fibre glass reinforced plastic sheet rooting up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovings incorporating minimum 0.3% ultra-violet stabiliser in resin system under approxirnately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2 mm thick flat

12.52.2 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in perforated Tegular global white color tiles of size 595x595 mm and 0.5mm thick with 8 mm drop; made of GI sheet having glavanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyster powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

12.53 : Providing and Fixing 15 mm densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone /cosmos /Hexa or equivalent of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' of size 24 x 28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x28 mm made of 0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from grid of size 600x600 mm, resting on periphery walls/partitions on a Perimeter wall angle pre-coated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require. Main 'T' runners to be suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size of 85x30x0.8 mm, spaced at 1200mm centre to centre along main 'T' bottom exposed with 24 mm of all T- sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by by engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. value of 0.50 (Minimum), light reflection > 85% non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity < 0.043 w/m 0 KC.

FINISHING WORK

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.1.2 : 12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

od170761/2022_2023 : 12 mm cement(with fly ash) plaster finished with a floating coat of neat cement of mix: 1:3 ( 1 cement : 3 fine sand)

od170763/2022_2023 : 12 mm cement(with fly ash) plaster of mix: 1:4 ( 1 cement : 4 fine sand)

od170764/2022_2023 : 6 mm cement(with fly ash) plaster of mix: 1:3 ( 1 cement : 3 fine sand)

13.21 : Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.28.2 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Sunk Band

13.28.3 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Raised Band

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.44.1 : Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

13.45.1 : Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.50.3 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works

13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.114 : Melamine polishing on wood work (one or more coat).

FAÇADE WORKS

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

od238040/2022_2023 : Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 34 %, Light reflection internal 8%, light reflection external 23 %, shading coefficient (0.39),SHGC- 0.34 and U value of 3.9 W/m2 degree K etc. The properties of performance glass shall be adjusted as per the GRIHA requirement and manufacturer specification.

25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providingand supplying at site all accessories and hardwares for the openable panels asspecified and of the approved make such as heavy duty stainless steel frictionhinges, min 4 -point cremone locking sets with stainless steel plates, handles,buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,washers etc. all complete as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge.

25.5 : Providing,fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi - rigid, inorganic, non- combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5mm and nominal mass not less than 60 gm/ sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts,bolts, washers etc complete.

25.6 : Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc., all complete for the required performance as specified, as per the architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in - Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass panels in the curtain glazing is included in cost of relevent item*).(ii) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face #2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35%, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25 - 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

26.8 : Providing and fixing 50 mm thick extruded polystyrene rigid insulation board ofrequired size under deck on ceiling surface, complying with ISO 4898:2008 &ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as perASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listedas per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, waterabsorptions 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fireretardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 classA, fixed with suitable water based adhesive and fastener, complete in all respectas per the direction of Engineer-in-Charge.

26.27.3 : Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tileconfirming to ISO 5 (class 100 ) specifications

od239910/2022_2023 : Providing and fixing 50BD Louvers of approved make colour consisting of panel 50 mm wide x 75mm deep x 0.6mm thick at a spacing of 125mm c/c as per drawing , length upto 3mtrs coil coated on a continues paint line double baked and roll formed from enameled corrosion Resistance Aluminum Alloy AA3005 (Al.Mg.) . Panels shall be clipped at a distance of 75 mm to GI Mullion using pop rivet to hold the panel in a module of 75mm centre to centre. Mullion shall be fixed at 150 mm from panel ends and at a distance of maximum 1200 mm center to center across the panel span.

od171876/2022_2023 : Providing and fixing powder coated Aluminium louvered Ventilators (minimum thickness of powder coating 50 microns) of approved colour HINDALCO or equivalent 9771, with 5mm thick frosted glass of approved make for aluminium U channel louvers including necessary grooves in frames for fixing glass etc. complete. Providing and fixing powder coated Aluminium louvered Ventilators (minimum thickness of powder coating 50 microns) of approved colour HINDALCO or equivalent 9771, with 5mm thick frosted glass of approved make for aluminium U channel louvers including necessary grooves in frames for fixing glass etc. complete.

WATERPROOFING WORKS

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

22.22 : Providing and mixing integral crystalline admixture for waterproofing treatment toRCC structures like basement raft, retaining walls, reservior, sewage & watertreatment plant, tunnels / subway and bridge deck etc.. at the time of transportingof concrete into the drum of the ready-mix truck , using integral crystalline [email protected]% (minimum) to the weight of cement content per cubic meter of concrete)or higher as recommended by the manufacturer's specification in reinforced cementconcrete at site of work. The material shall meet the requirements as specified inACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%,compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostaticpressure. The crystalline admixture shall be capable of self-healing of cracks up toa width of 0.50mm. The work shall be carried out all complete as per specificationand the direction of the Engineer-in-charge. The product performance shall carryguarantee for 10 years against any leakage.

22.22A : Providing and applying fibre reinforced elastomeric liquid water proofing membranewith resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top ofconcrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming ofelastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and twocoats of undiluted elastomeric waterproofing liquid (dry film thickness of completeapplication/system not less than 500 microns). The operation shall be carried outafter scrapping and properly cleaning the surface to remove loose particles withwire brushes, complete in all respect as per the direction of Engineer-in-Charge.

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer in-charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer in-charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

22.26 : Providing and applying of swellable type water stop tape, 19mm x 25mm thick inlinear meter (expansive nature) for construction joints treatment of RCC structuresuch as raft slab, retaining walls, water storage tank and at the junctions of raftslab with the retaining walls etc.. After cleaning the surface, one coat of requiredprimer for swellable water stop tape shall be applied throughout the length of thejoint @3.78 litre per 240 running meter. Over the primed surface swellable typewater stop tape shall be placed. The work shall be carried out all complete as perspecification and the direction of the engineer-in-charge. The product performanceshall carry guarantee for 10 years against any leakage.

DEMOLISHION WORK

15.2.2 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 leaner mix ( including equivalent design mix)

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.13.1 : Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 50 metres lead:Of area 3 sq. metes and below

15.18 : Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,boltd, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

ROAD WORK

3.6 : Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

4.2.A.2 : Construction of granular sub-base by providing graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. Grading-IV - For lower sub base - Mix in Place Method

4.12 : Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

4.4.1 : Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size)

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

5.1.a : Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

5.2.a : Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

5.3.2.a : Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder (VG 30), transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction.For Grading II - (19 mm nominal size)

5.6.1.a : Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder( NRMB) @ 5.2 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects For Grading - I ( 19 mm nominal size )

od324101/2022_2023 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or road and parking etc, of required strength, thickness size/ shape, made by table vibratory method using PU mould, laid in required colour pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-40 grade with approved color design and pattern.

LANDSCAPING WORKS

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.4.1 : Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.14.3 : Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 60 cm dia, and 60 cm deep

30.2.17.1 : Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with:A coat of coal tar

30.2.20 : Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

30.2.25 : Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

50.12.2.1 : Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required.

50.17.1.1 : Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

od171885/2022_2023 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material&rsquo;s as per direction of officer in charge (excluding cast of plant water) - Trees Plant

od171886/2022_2023 : Providing and displaying of Tree plants in Earthen pot or in ground as per direction of the officer-in-charge.

od171888/2022_2023 : Providing and fixing solid bio degradable organic waste compost bins with protection grill and roof

SANITARY, WTP works etc

od240121/2022_2023 : Providing and fixing white vitreous china wall hung wash basin of approved make including one CP brass pillar cock with water conservation mechanism including connecting pipes with all fittings 32 mm dia rubber plugs 32 mm dia CP brass waste coupling ,complete including CI/MS brackets duly painted, nuts, washers, etc. complete,cost and conveyance of all materials labour charges ,lead, lift necessary wall cutting / chasing and making good the walls,floors,slab,testing and commissioning to the satisfaction of Engineer in charge at all levels. The flow-rates of pillar tap shall be 4 LPM or as per GRIHA water conservation requirement .

od240127/2022_2023 : Providing and fixing white vitreous china flat back urinal with sensor and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: complete as directed by the Engineer in charge at all levels.The flowrates of urinal shall be 1.5-2 LPF or as per GRIHA water conservation requirement .

od240142/2022_2023 : Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.The faucet shall meet the flow regulation as per GRIHA requirement 4 lpm specified as per tender conditions.

od240165/2022_2023 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern C.P. flush bend with fittings C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. The water closet shall be 4/2 LPF flush and all fittings shall meet GRIHA water conservation requirement as per tender conditions.

od240169/2022_2023 : Providing and fixing sanitary fixtures for handicapped toilet including one wash basin , one number pillar cock with aerator all other related fittings like CP brass bottle trap,CP brass angle valve, CP brass waste coupling, etc, one number EWC Cistern complete with fittings seat cover, one no. hinged rail 4 nos. of grab rails 60cm etc, designed for people with special needs comes with as per manufacturers specification including cutting and making good the walls and floors wherever required as directed by Engineer-in-Charge. For griha water conservation mechansim following flow-rates shall be adopted for fixtures.Water Closet (Full flush/ Half flush) = 4 / 2 LPF,Lavatory Faucet = 4 LPM or as per GRIHA water conservation requirement .

od240181/2022_2023 : Providing and fixing C.P. brass long body bib cock with griha water conservation mechansim of approved quality conforming to IS standards and weighing not less than 690 gms. The flow-rates of bib cock shall be 4 LPM or as per GRIHA water conservation requirement .

od240189/2022_2023 : Providing and fixing sink cock of approved quality conforming to IS 8931, with GRIHA water conservation mechanism as approved by the engineer in charge at all levels.The flow-rates of sink cock shall be 4 LPM or as per GRIHA water conservation requirement .

od240193/2022_2023 : Providing and fixing premium quality C.P. brass wall shower mixer with griha water conservation mechanism along with overhead shower and shower arm with wall flanges of approved make and model including cost of all materials, labour etc., complete as directed by the Engineer-in- Charge at all levels. The flow-rates of Shower Head shall be 6-8 LPM or as per GRIHA water conservation requirement .

17.1.1 : Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.3.2 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.c. pan with ISI marked black solid plastic seat and lid

17.7.1 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.9.1 : Providing and fixing kitchen sink with C. I brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required:White glazed fire clay kitchen sink of size 600x450x250 mm

17.10.1.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.10.2.2 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x460 mm bowl depth 200 mm

17.12.1 : Providing and fixing draining board with C.I brackets including painting of brackets, cutting and making good the walls wherever required:White glazed fire clay draining board of size 600x450x25 mm

17.18.1 : Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete.10 litre capacity - White

17.22A : Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

17.22B : Providing and fixing CP Brass Single lever telephonic wall mixer of quality& make as approved by Engineer in charge.(a) 15 mm nominal dia

17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia

17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.32.2 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

17.72 : Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

17.73.1 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms

18.15.2 : Providing and fixing brass bib cock of approved quality :20 mm nominal bore

18.16.2 : Providing and fixing brass stop cock of approved quality :20 mm nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.17.5 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore

18.17.6 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore

18.18.2 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.18.3 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.21.2.2 : Providing and fixing uplasticised PVC connection pipe with brass unions:20 mm nominal bore

18.31.1.1 : Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):100 mm diameterClass I

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.55.2 : Providing and fixing PTMT stop cock of approved quality and colour.20 mm nominal bore, 89 mm long, weighing not less than 88 gms

18.56.1 : Providing and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 107 mm long, weighing not less than 110 gms

18.57.1 : Providing and fixing PTMT, push cock of approved quality and colour.15 mm nominal bore, 98 mm long, weighing not less than 75 gms

18.58.1.1 : Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia

18.59.1 : Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber insertion etc. complete ( The tail pieces, tapers etc. if required will be paid separately):50 mm dia

18.75.3 : Providing and fixing PTMT extension nipple for water thank pipe, fittings of approved quality and colour .25 mm nominal bore, weighing not less than 62 gms

18.76.1 : Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. ( non modular ) brick

18.77 : Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.1.2 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With Sewer bricks conforming to IS : 4885

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.15.1 : Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) as per standard design.With 20x20 mm square bar

19.18.1 : Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

19.19.1.2 : Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.L D - 2.5Square shape 450 mm internal dimensions

19.19.4.1 : EHD - 35Circular shape 560 mm internal dia

19.30.1.1 : Constructing brick masonry chamber for underground C.I. inpection chamber and bends with bricks in cement mortar 1:4 ( 1 cement: 4 coarse sand) C.I.cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg), R.C.C top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.35.2 : Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.600 mm dia RCC pipes.

od170287/2022_2023 : Providing, installing, testing and commissioning of approved make Conductive type level sensor with SS 316 probes MS 2-1/2 table E std flange and weather proof cast aluminium enclosure to sense two levels of the under ground sump and the OH water storage tank

od170288/2022_2023 : Supplying, installing, testing and commissioning of DWC SN8 class Pipe laid to the required level and joining in Elastomeric Sealing Ring for On-line system or with extra couplers and filling the excavated trench with approved quality saturated sand on sides, bottom and top surface of pipe with all leads and lifts, making necessary connections as required etc., complete. a) 110 mm dia.

od170289/2022_2023 : Supplying,Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping,valves,suitable supports for mounting pressure guages,orifice plates.The filter shall be made of MS vessel with necessary protective coating.The cost of filter shall also include initial charge of underbed multi-grade filter media to suit the requirement etc.,complete as per the standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 11.5 cum/hr,at 10 hrs cycle

od170290/2022_2023 : Supplying, Installing, testing and commissioning storm water disposal submersible pump with IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440V with necessary unions, flanges, Auto level controllers etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent. 1) 15 Lps at 15M head.(Roof water collection sump) ( 1 no. working + 1 no. standby = 1 Set)

od170291/2022_2023 : Supplying, installing, testing and commissioning approved make Water Softener with necessary Accessories complete with Frontal piping,valves,suitable supports for mounting pressure gauges, orifice plates.The softener shall be made of MS vessel with necessary protective coating.The cost of Softener shall also include initial charge of Resin media to suit the requirement etc.,complete as per standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 7.0 cum/hr,at 10 hrs cycle.

od170293/2022_2023 : Supplying, installing, testing and commissioning of DWC SN8 class Pipe laid to the required level and joining in Elastomeric Sealing Ring for On-line system or with extra couplers and filling the excavated trench with approved quality saturated sand on sides, bottom and top surface of pipe with all leads and lifts, making necessary connections as required etc., complete. b) 160 mm dia.

od170294/2022_2023 : Supplying, Installing, testing and commissioning storm water disposal submersible pump with IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440V with necessary unions, flanges, Auto level controllers etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent. 2) 2.80 Lps at 20M head.(STP UG Sump water sump pump) (1 no. working + 1 no. standby = 1 Set)

od170295/2022_2023 : Supply laying of 4 core 1.5sqmm copper armoured cable from UG sump / over head water storage tanks sensors to level control instruments laid in a 32mm dia. PVC 6Kg/sqcm pipes.

od170296/2022_2023 : Providing and fixing coloured vitreous china under counter round wash basin 440 mm dia or nearest size of approved make including one CP brass pillar cock 15 mm NB including connecting pipes with all fittings 32 mm dia rubber plugs 32 mm dia CP brass waste coupling, 32 mm dia CP brass bottle trap, 15mm angle valve, etc. complete as directed by the Engineer-in-charge.The flow-rates of pillar tap shall be 4 LPM or as per GRIHA waterconservation requirement .

od170298/2022_2023 : Supplying, installing, testing and commissioning approved make activated carbon filter in MS vessel construction with internals, electrical control system complete with Frontal piping, valves, suitable supports for mounting, pressure guage, orifice plate etc.., complete as per the detailed specification for the efficient working of system. The maximum working Pressure shall be 3.5 Kg/Sqcm. Max flow rate = 7.0 cum/hr,at 10 hrs cycle

od170299/2022_2023 : Providing, installing, testing and commissioning of approved make Water level Control instrument.

od170300/2022_2023 : Supplying, Installing, testing and commissioning of Terrace booster hydro pneumatic system with Multiple variable frequency drive. The system shall comprises of pump, pre charged pressure tank, pressure switch etc., complete with electric motor at 2900 RPM 415V 3Ph 50 Hz required duty conditions mounted on common base plate and wiring from panel to the motor including air volume controls, etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent. Flow Rate : 2.0 Lps (each pump 1.0 lps) with 2 pump system for Domestic Water Distribution

od170301/2022_2023 : Supplying, installing, testing and commissioning of DWC SN8 class Pipe laid to the required level and joining in Elastomeric Sealing Ring for On-line system or with extra couplers and filling the excavated trench with approved quality saturated sand on sides, bottom and top surface of pipe with all leads and lifts, making necessary connections as required etc., complete. c) 200 mm dia.

od170302/2022_2023 : Supplying approved make PVC gully trap of size 160 x 110mm and CI grating 150mmx150mm size and light duty C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than4.5kg and frame to be not less than2.7kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cmx30cm internal size gully trap chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm thick plastering inside with CM 1:3,12mm thk with a neat cement flushing coat and conveying to site,cleaning ,installing and testing approved make PVC gully trap with 160mm outlet(Fabricated),surrounding with CC 1:1.5:3, 150x150mmm,top with CI grating above the PVC gulley trap and light duty CI cover and frame over the chamber including cost of all materials, etc complete as per approved drawing and as directed by Engineer-in- Charge.

od170304/2022_2023 : Supplying, Installing Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.)and including Concealed work, including cutting, chases and making good the walls etc. 50mm dia

od170307/2022_2023 : Making water supply connection from the municipal water line with all the necessary works including cutting the corporation road and making good the road after connection. The contractor responsibility shall include submitting the papers to the municipal department follow up and get the approval etc,. Complete. (Only statutory charges shall be paid by the client)

od170308/2022_2023 : Supplying, installing, testing and commissioning inter unit .SH 80 piping with necessary flanges, bolts, nuts, neoprene gaskets, welding wherever necessary, with necessary control valves, non return valves etc and with one coat of primer and two coats of approved enamel paint with IS recommended colour etc., complete.

od170309/2022_2023 : Supplying, fixing, testing and commissioning pump set (horizontal or vertical type) of adequate HP capable of giving a required discharge at suitable head to work on 3Ph. 50Hz, 400/440 V with necessary unions, flanges, foundation bolts, etc., complete.Make: Grundfos/ Lubi/ Shakti Approved Equivalent ) 1) 2.5Lps at 40 M head. 1 no. working + 1 no standby for domestic water supply

od170312/2022_2023 : Supplying Fixing electrically operated horizontal storage heater with M.S. steel glass lined vessel with 1.5-2 Kw heating element, auto-thermostatic switch, neon indicator lamp, pressure relief valve etc. as specified in the specifications, complete in all respects.

od170314/2022_2023 : Supplying, fixing, testing and commissioning pump set (horizontal or vertical type) of adequate HP capable of giving a required discharge at suitable head to work on 3Ph. 50Hz, 400/440 V with necessary unions, flanges, foundation bolts, etc., complete.Make: Grundfos/ Lubi/ Shakti Approved Equivalent ) 2) 1.0 Lps at 40 M head. 1 no. working + 1 no standby Flushing Water Distribution

od170316/2022_2023 : Supplying, Installing Testing at site in position CPVC Sch-80 of approved make for Pump room water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. U bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) of approved make, as per drawings to the satisfaction of the Project Manager. (For Pump room Piping) 75 mm nominal inner dia Pipes

od170320/2022_2023 : Supplying, Installing Testing at site in position CPVC Sch-80 of approved make for Pump room water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. U bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) of approved make, as per drawings to the satisfaction of the Project Manager. (For Pump room Piping) 100 mm nominal inner dia Pipes

od170322/2022_2023 : Supplying, fixing and testing salt glazed stoneware gully trap with rebated top square bodies 150mm x 150mm, CI grating 100mm dia outlet set in 75mm thick PCC 1:4:8 bed, 230mm thick masonry chamber in CM 1:3, internal and external plastering 12mm thick in CM 1:6 and 1:3 respectively, supply and fixing 450mm x 450mm size CI frame and cover, jointing to drain in CM 1:1, excavating, and cover, jointing to drain in CM 1:1, excavating, refilling and ramming etc., complete.

od170325/2022_2023 : Construction of valve chamber with 230 mm best quality TM bricks in CM 1:4 over a bed of 100mm thick PCC 1:4:8, internal walls plastered smooth in CM 1:3 and external walls plastered rough with sponge finish including curing with all necessary leads and lift and providing heavy duty cast iron cover with frame with locking arrangements etc., complete including Heavy duty cast iron cover of size 600 x600 (weight 115Kgs.) Size of chambers for valves up to 150 mm dia Size 0.6m x 0.6m x 1M (clear dimension) including. 100mm nominal dia

od170327/2022_2023 : AMC for disinfection , CIP, preventive maintenance, treated water testing etc.

od170329/2022_2023 : Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete . 200 mm dia

od170333/2022_2023 : Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete . 65 mm dia

od170335/2022_2023 : Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete . 100 mm dia

od170337/2022_2023 :Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete . 150 mm dia

od170339/2022_2023 : Supply,Installation, Testing and Commissioning of brass body Air Release Valve 25 mm dia type of approved make.

od170340/2022_2023 : Supplying, installing ,testing and commissioning of Pressure gauges for the respective floors near to the flow switches with Ball valves, siphon, Fittings like unions / colors / reducers etc. Glycerine filled pressure gauges to use on pump discharge lines. with 0 to 200PSI, 25 mm dia. Dial should be 150 mm dia.

od170341/2022_2023 : Providing, fixing, supply, Installation and commissioning of 3 bay (2100mm long) brush finish scrub station ( manual operated) made out of high grade SS 304 1.6mm thk etc complete with all accessories i.e.thermostation mixing valve bypass system etc.

od170342/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

od170343/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

od170344/2022_2023 : Providing and fixing floor trap of PVC,110 mm outer dia(multi trap) including CP cockroach free floor grating with cup etc including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer-in-Charge at all levels

od170345/2022_2023 : Providing and fixing stainless steel grating of approved quality and colour. Circular type 100 mm nominal dia

od170346/2022_2023 : Supplying and fixing PVC rain water gutter of 200 mm size including necessary fittings such as clamps,,screw, end stopper etc. including cost of all materials labour charges scaffolding etc

od171844/2022_2023 : Supplying,Installing, testing and commissioning approved make Incinerator with necessary accessories complete as per the standards. Waste Type: Organic, Capacity: 40 kg/batch Burning Ability: 50kg/time

od171867/2022_2023 :Water purifier: Supplying,Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping,valves,suitable supports for mounting pressure guages,orifice plates.The filter shall be made of MS vessel with necessary protective coating.The cost of filter shall also include initial charge of under bed multi-grade filter media to suit the requirement etc.,complete as per the standards. Max. working pressure = 10kg/sqcm. Max flow rate = 6m3/hr/m2 800 dia filter,at 10 hrs cycle

od171904/2022_2023 : Supplying and fixing 32 mm dia GI pipe for gas out let connections including control valves, all plumbing works etc

od171905/2022_2023 : Supplying and fixing 250 mm dia PVC pipe from Inscpection chamber to Fermetation Tank gas out let connections including control valves, all plumbing works etc

od171906/2022_2023 : Supplying and fixing 24 cft biogas burner including all connections, control valves all plumbing works etc

od171907/2022_2023 : Supplying and filling cow-dung with equal quantity of water for bacteria formation

WATER SUPPLY PIPING WORKS

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.9.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work20 mm nominal outer dia pipes

18.9.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work32 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

18.9.8 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work75 mm nominal inner dia pipes

18.9.9 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work100 mm nominal inner dia pipes

18.9.10 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work150 mm nominal inner dia pipes

50.18.7.2.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall

50.18.7.3.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

50.18.7.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.7.5.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10 Kgf/cm2- Internal work- exposed on wall

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.8.2.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chased and making good the wall etc. 20 mm pipe 12 Kgf/cm2

50.18.8.3.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2

50.18.8.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

50.18.8.4.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2

50.18.8.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc 63 mm pipe 4 kgf/ cm2

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.8.9.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC Solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 110 mm pipe 4 kgf/cm2

50.18.9.3.2 : Providing and fixing PVC pipes includes jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm dia 10KGF/cm2

50.18.9.6.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2

50.18.9.6.2 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm2

50.18.9.7.1 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.8.2 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.9.2 : Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in CHarge. 110 mm dia 4 Kg/cm2

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.16.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work - Exposed on wall

50.18.9.16.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.17.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.17.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 4 Kgf/cm2- External work - exposed on wall

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.19.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall

50.18.9.20.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.2 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.3 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow

50.18.9.20.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.5 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

50.18.9.20.6 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee

50.18.9.20.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia vent cowl

50.18.9.20.8 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia End cap

50.18.9.20.9 : Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling

50.18.9.20.10 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63x50 mm dia Reducer

50.18.9.21 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.2 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow

50.18.9.21.3 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow

50.18.9.21.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.21.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

50.18.9.21.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee

50.18.9.21.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.21.8 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia End cap

50.18.9.21.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.21.10 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee

50.18.9.22.8 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

50.18.9.22.10 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.78 : Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

MISCELLANEOUS WORK

od238863/2022_2023 : Providing and applying Antitermite treatment by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for pre-constructional treatment and creating a chemical barrier as per IS 6313 Part II 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, etc. complete conforming to manufacturers specification and as directed by the Engineer in Charge. Plinth area only to be measured for the payment .The contractor should give guarantee for 10 years for the work .

od323673/2022_2023 : Design Supply Installation Testing and Commissioning of 75 KLD Sewage Treatment Plant Based on MBR Technology including all the mechanical and electrical equipment&apos;s like approved pumps, MBR membranes, filters, dosing system etc complete for the full function of Sewage Treatment Plant. The civil foundations and RCC tank structures / pump rooms shall not be included in this item and shall be paid separately. Design of the MBR system shall be done as per site conditions and got approval from engineer in charge before procurement. Work shall be done as per manufacturer recommendation, technical specification and as per the direction of engineer in charge

Design supplying, Installation, Testing, and Commissioning the SOLAR HYBRID HOT WATER SYSTEM of 3000 LPD pressurized solar water heater.The system inlet working pressure @4kg/cm2.Also shall provide minimum 5 Tonne Air source Heat Pump 515 LPH( 4.9kw input power and 21kw heating capacity COP- 4.29).Delta-35 Temperature controller,2nos. Hot water circulation pump and inter connection plumbing between tank to panel and heat pump etc complete as per design and manufacturer specification and as directed by engineer in charge at all levels.

SIGNAGE & WAY FINDINGS

od69657/2023_2024 : Design, Supply and installation of Aluminium profile sliding door signage with the following specifications. The signage shall have an aluminium profile modular frame of height 100mm. The letters shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board/ ACP Board fixed with adequate fasteners. The signage shall be in such a way that the foam board/ACP Board is slide to the aluminium profile for easy replacement of names : size-300mmx100mm

od69658/2023_2024 : Design, Supply and installation of vinyl signage on ACP with the following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on 3mm thick ACP backing using VHB tapes.ACP backing surrounded by 50mm dia 1mm thick ss plated tube along the perimeter supported by 2 nos of 50mm dia 2mm thick ss plated pole permanently fixed at ground by concrete or can be fixed on wall support as per directions by engineer in charge.- ACP board size (2400x1200) bottom fixed at 60cm from ground as per the directions of engineer in charge.

od69659/2023_2024 : Design, Supply and installation of vinyl signage on ACP with the following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on 3mm thick ACP backing using VHB tapes.ACP board size (2400x1200) bottom fixed at 60cm from ground as per the directions of engineer in charge.

od69660/2023_2024 : Design, Supply and installation of Reception/helpdesk signages as per following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl pasted on3mm thick ACP/ 6mm thick hybrid board or 8mm Thick Acrylic glass on single side of approved make and colour of height 150mm. The signage shall be ceiling suspended using Stainless Steel strings as per the directions of engineer in charge, TEXT (MAY I HELP YOU, CASH, RECEPTION , REGISTRATION, INSURANCE..etc..)

od69661/2023_2024 : Supply and installation of way finding signages as per following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl pasted on 3mm thick ACP/ 6mm thick hybrid board on both sides of approved make and colour.The signage shall be ceiling suspended using Stainless Steel strings as per the directions of engineer in charge. Way Finding Signage: 1200mmx600mm

od69662/2023_2024 : Design,Supply and installation of circular door signage for number with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on doors using VHB tapes : size of signage- 100mm dia

od69663/2023_2024 : Supply and installation of door signage with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick sunboard and installed on doors using VHB tapes: Door Signage: 300mmx100mm

od69664/2023_2024 : Supply and installation of signage board with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick sunboard and installed above doors using VHB tapes : Signage size: 1200mmx150mm

od69665/2023_2024 : Design,Supply and installation of Vinyl printed signage for awareness and guidelines for hospital departments as specified by the client with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on wall/glass using VHB tapes.Room vinyl printed sticker with 3mm foam board backing as per the directions of engineer in charge.

od69666/2023_2024 : Supply and installation of 3 mm Acrylic box letters with 70 mm projection, vinyl pasted on first face with 3 module LEDs, SMPS and other electrical fittings fixing on ACP/wall base as per the directions of client/engineer in charge.

od69667/2023_2024 : Supply and installation of frosted film pattern throughout all the internal glass panels wherever required of upto 1.5 m height as per the approved pattern as per the direction of Engineer in charge.

od69668/2023_2024 : Design,Supply and installation of Vinyl printed self adhesive sticker signage on glass for awareness and guidelines. with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on glass.

od69669/2023_2024 : Providing and fixing of 3mm thick ACP/ 6mm thick hybrid board or 8mm Thick Acrylic glass backing for singnage. Shall be fixed by means of ss studds or screwed as per directions of engineer in charge the price shall be inclusive of all hardwares and accesories used for fixing as per the directions of engineer in charge.

od69670/2023_2024 : Supply and installation of 8mm thick Glass marker board with led lights (900X900)mm on wall as per directions by engineer in charge.

od69671/2023_2024 : Supply and installation of Laminated fire evacuation plan colour print as per NBC 2016,IS 1644-1988 standard, installed on doors /walls using VHB tapes. as per directions by engineer in charge.

od69672/2023_2024 : Supply and installation of FIRE EXIT SIGNAGE ,size: 12 inch x 6 inch ,Color: green ,Film Type Photoluminescent. The signage shall be ceiling suspended using Stainless Steel strings as per NBC 2016 standards the directions of engineer.

od69673/2023_2024 : Design, Supply and installation of SS signage on ACP with the following specifications. The letters shall be made out of 40mm projected ss plated box signage with 3mm ACP/ Aluminium sheet backing supported by 2 nos of 75mm dia 2mm thick GI painted pole permanently fixed at ground by concrete - ACP board ( Text - GOVERNMENT TALUK HOSPITAL, IRITTY/HOSPITAL BLOCK etc or as per directions of engineer in charge.

Description of Work / Item(s)

Amount

Electrical

HT/LT INSTALLATIONS od382398/2022_2023 : Supply,Installation,testing and commisioning of 120AH, 24V station type, sealed maintenance free lead acid batteries complete with battery stand, full wave bridge SCR battery charger (trickle / boost) inclusive of control panel.

od382399/2022_2023 : TOD METER (OUTDOOR LBS with METERING PANEL) Supply installation testing and commissioning of 11kV,outdoor,wheatherproof, metering with 11kV, 3phase, 50hz, 400A, load break switch having short time current rating of 18kA, cubicle fabricated out of 14 SWG CRCA sheet, powder coated after seven tank process, provision for connecting 3x300sqmm cable at both ends, 3nos 25/5A, Cl-0.2s, 10VA CT, 11kV/110V, Cl-0.2, 25VA PT, fixing of already tested TOD meter fixed in pilfer-proof outdoor meter box suitable for housing the meter and test terminal block (TTB), all complying with relevant standards and as per the requirements of KSEBL including excavation, backfilling RCC foundation for panel.

od382400/2022_2023 : Supply, installation and testing of TOD meter for KSEB (0.2S accuracy class, 3ph 4 wire, DLMS compatible) test terminals etc. including arranging testing of CT and meter in the TMR section of KSEB and as per recommendations and fixing in the metering panel complete as required.

od382401/2022_2023 : UNITISED SUB STATION - INDOOR - WITH VCB PANEL - 11KV - 630KVA. Indoor Unitised Substation (USS) with the following: Incomer: 11kV,630A, 500MVA, VCB , 24V dc shunt trip coil, battery, battery charger, overcurrent and earth fault relay, protection CT, 50-25/5A, Cl 5P10 CT, 3O/C and 1EF Protection static relays with high set element, cable box suitable for 3x300sqmm 11kVcable and emergency OFF push button,etc including all accessories in complete - 1No. Transformer: 630kVA, 11kV/433V, 50Hz, 3phase, Cu-wound AN cooled, Vector DYN-11, cast resin, indoor, dry-type transformer with off-load tap changer, winding temperature alarm and trip, HV top entry type cable box, LV terminals suitable for connecting cable of 4 run 3.5x400 sqmm cable - 1No Suitable base plate for mounting of the equipment, bus bar inter connections, operating handle mechanism, spring charging mechanism and enclosure for the USS.

od382402/2022_2023 : Supply, testing and commissioning of the following 6.35/11kV PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) / XLPE (A2XCEFY) to be laid in HT trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers etc. required for clamping intervals as necessary.3C x 300 mm2.XLPE

od382403/2022_2023 : Supply, testing and commissioning of the following 6.35/11kV PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) / XLPE (A2XCEFY) to be laid in HT trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers etc. required for clamping intervals as necessary..3C x 150 mm2.XLPE

8.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

8.4.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Upto 120 sq. mm

HT CABLE TERMINATION 10.5.2 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :150 sq. mm

10.5.3 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :240 sq. mm

10.5.4 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

od383531/2022_2023 : DIESEL GENERATOR SET Supply of 3 phase., 320kVA, 433V,0.8pf, 50Hz, 1500 RPM, DG Prime Rated Diesel Generator Sets as detailed. water cooled diesel generating set comprising of 6 cylinder of minimum 380 BHP micro processor based engine controlled diesel engine, 625kVA alternator with AVR, fuel tank, starting system, battery, electronic governor, residential silencer, antivibration mounting, etc. with all accessories as required. The generator set shall have an integral type acoustic enclosure as per latest CPCB norms. Smoke exhaust emission from diesel engine shall comply with the latest emission standards. Generator set shall be inclusive of fly wheel, flexible coupling, air cleaner, corrosion resistor, fan with guard, fuel pump, fuel filter, electrical starting system with starter, 24V battery with charger, instrument panel, RPM indicator, residential silencer, etc. The control panel shall be floor mounted dust and vermin proof with suitably rated, 4Pole, 630A, 50kA, MCCB complete with all necessary relays, CTs, control wiring, etc. as necessary for interconnection with PLC. Scope shall include first filling of oil and diesel for commissioning of the DG set.

od383532/2022_2023 : DIESEL GENERARTOR SET Installation testing and commissioning of 3phase.320kVA 433V, 0.8pf. 50Hz, 1500rpm DG Prime Rated Diesel Generator Sets (Installation only).

od383533/2022_2023 : &nbsp;&nbsp;Providing, fixing of exhaust pipe line of 200/150mm dia B class MS pipe with accessories like flange, supports, through wall, including providing thermal insulation heat resistance painting etc complete.±

od383534/2022_2023 : SITC of Three Phase Input / Output IBGT based parallel redendunt (2X30) 60 KVA UPS system with minimum one hour back up :- The Three Phase input Voltage shall be 4wire, 415V, variable between +20% to &ndash;20%; 50Hz +/- 6%. The UPS System shall deliver Clean; ripple free pure sine wave output waveform in presence as well as failure of supply mains. The current and voltage harmonic distortions generated by the UPS systems shall be with in acceptable limits as per international and national norms. (Ripple [without Battery &l1 %]), (THD; 2% max, for 100% Linear load &lt; 5% max, for 100% Non-Linear load)UPS system shall be Double conversion, Microprocessor based True On Line system with individual battery banks having in-built galvanic Isolation Transformer at output and own Cooling arrangements.UPS system shall be with LCD Display, 3& Phi; input and 3&Phase; output; with PWM IGBT based DSP control, 20 Minutes external SMF battery backup and auto by-pass.output voltage Range - 415V &plusmn; 0.5%,frequency Range - 50 Hz, &±; 0.05%,O/P power factor shall be minimum 0.9 ,THD (Linear Load) - ;2% THD (Non Linear Load) - ;5% Crest Factor - 3:1 efficiency - 95%,over load capacity - 110% - 5min , 150% - 30s.

PANEL BOARDS od395770/2022_2023 : .;MSB WITH PLC BASED AMF SYSTEM: -MAIN SWITCH BOARD (MSB):.Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, panel board fabricated using CRCA 16/14 SWG wpowder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process. The panel shall be complete with all necessary switch gear, control gear, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. as required and as listed below in brief and details in technical specifications.All necessary components, rotary handle, spreader, neoprene gasket, door locking arrangements, suitable earth bus including all accessories. Incomer:.1. 1000A, 415V,50KA 4P EDO type ACB, -1 set.2.630A 4P ISO, and 630 A 4P CONTACTOR-2set.Bus coupler: 1000A, 415V,50KA 4P EDO type ACB, -1set.Bus Bar:: Al bus bar sized suitably for 1000A and surge protector. Outgoing:.1. MCCB 400A TP 35KA &microprocessor based - 1No,.2. MCCB 250A TP 35KA &micro;P based - 3 Nos.3.MCCB 200A/160 TP 35KA - 9 Nos.4. 250A TPN ISO - 1No.Automatic Logic Control: - Panel shall be with PLC logic system to automate the panel incomers and bus coupler with power supply unit, AI, DI, DO, cards, processor, control wiring with all switches, push button switches, indication lamps, bypass arrangements, contactors, including all instrumentation and controls..Metering: All incomers and bus coupler shall be provided with Multifunction Maximum demand indicator with communication port, RYB and On/Off indication, CT&rsquo;s. .Protective relays: Low set earth fault relay with protection class CT&rsquo;s (with enclosure) and wiring.

od395771/2022_2023 : .;Medical equipment SM DB.Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays and CT&apos;s, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following ..Incomer: 250A 4P ISO&amp; Indication lamp with control fuse. . Bus bars: 250A Al for Phase 250A AL for Neutral, 25X6 mm cu for Earth Outgoings: 100A MCCB 25kA TPN &ndash; 4 Nos, 63 A MCCB 25kA TPN-2 Nos, 40 A MCCB 25kA TPN-1 No.

od395772/2022_2023 :UTILITY PANEL SM DB.Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . ..Incomer: 200A 4P ISO &amp; Indication lamp with control fuse. .Bus bars: 200A Al for Phase 400A AL for Neutral, 25X3 mm cu for Earth Outgoings: MCCB 100A 25KA TPN &ndash; 5 Nos, 63A MCCB 25KA TPN- 3 Nos.

od395773/2022_2023 : .;AC SM DB.SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle RYB indication lamp- 1No indication lamp for incomers, control fuses, spreaders, Control Wiring, Surge Protector - 1No etc. panel board shall be fabricated using CRCA 16 SWG / 1.6 MM MS sheet steel. The sheet steel fabrication will be treated through 7-tank cold pre-treatment process before powder coating. Panel shall be powder coated with approved colour and interconnected with Aluminium Bus bars. The Panel shall be packed compactly using water proof stretch PVC film..Incomer: 200A 4P Isolator &amp; Indication lamp with control fuse. .Bus bars: 200A Al for Phase 200A AL for Neutral, 25X3 mm cu for Earth Outgoings: 100A MCCB 25KA TPN &ndash; 1 No, 63A/40 /32 A MCB TPN -6 Nos, Bus bars:-200 A Aluminiumbus bar ,Cu earth bar suitable size.

od395774/2022_2023 : Lighing and Power SMDB:.Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following .Incomer: 250A TPN Isolator &amp; Indication lamp with control fuse. Bus bars: 250A Al for Phase 250A AL for Neutral, 25X3 mm cu for Earth Outgoings: 100A MCCB 25KA TPN &ndash; 2 Nos, 63A MCCB 25KA TPN -8 No, Bus bars:-250 A Aluminiumbus bar ,Cu earth bar suitable size.

od395775/2022_2023 : Sub main Distribution board(SMDB-A-X-F).Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following ..Incomer: 125A TPN Isolator &amp; Indication lamp with control fuse. Bus bars: 125A Al for Phase 150A AL for Neutral, 25X3 mm cu for Earth Outgoings: 63A MCB D curve FP -8 Nos Bus bars:-150 A Aluminiumbus bar ,Cu earth bar suitable size.

od395776/2022_2023 : .;UPS O/P Panel.Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following ..Incomer: 200 A TPN Isolator &amp; Indication lamp with control fuse. Bus bars: 200 A Al for Phase 200A AL for Neutral, 25X3 mm cu for Earth Outgoings: 100A TP MCCB -1 No , 63A TPN MCB -7 Nos , 32A TPN MCB -4 Nos.

od395777/2022_2023 : .;Floor Panel .Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following ..Incomer: 125A TPN Isolator &amp; Indication lamp with control fuse.Bus bars: 125A Al for Phase 150A AL for Neutral, 25X3 mm cu for Earth Outgoings: 63A MCB D curve FP -8 Nos Bus bars:-150 A Aluminiumbus bar ,Cu earth bar suitable size.

od395778/2022_2023 : Lift Panel Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 125/100A,TPN Isolator &amp; Indication lamp with control fuse - 1 set Outgoings: 63A, TP, D Curve, MCB - 4Nos.Bus bars:-150 A Aluminiumbus bar ,Cu earth bar suitable size.

od395779/2022_2023 : .;APFC Panel 200 KVAR (Ward Tower):SITC of 8 Stage Automatic Power Factor Correction Panel made of 14/16SWG thick CRCA sheet fully compartmentalized, dust and vermin proof, degreased, pickling, zinc phosphate and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty neoprene gaskets, removable gland plates made of 3mm thick sheet steel boards with 500V, APPH, Heavy Duty Capacitor and 7% detuned reactors, Capacitor Duty contactor and microprocessor based APFC Relay in steps of 12 with all required accessories. Including capacitor duty contactor, auxiliary contactor, (2 no+ 2nc), auxiliary contactor add on, (2 no+ 2nc), fan, air vent, auto manual ON/OFF indication switch, cooling fan etc. .Incomer: 400A 4P Isolator - 1 No microprocessor based APFC Relay (8 Steps) - 1No, 400/5A, CL- 1, CT, 10VA &ndash; 3 Nos, Multi-function digital meter - 1Set, RYB Indication Lamp - 1Set .Bus bars: 400A Al bus bar, Cu Earth bus. .Outgoings: 1. 50kVAr,500V APPH, with 7% detuned reactor, with 160A fuse set capacitor duty contactor, ON/Off indication lamp &ndash; 2 set,.2. 25kVAr APPH, 500V with 7% detuned reactor with 63A fuse set - 2 Set, .3. 10kVAr APPH, 500V with 7% detuned reactor with 32A fuse set - 2 sets, .4. 5kVAr APPH, 500V with 7% detuned reactor with 32A fuse set -1Set, .5. (one number 25kVAR as fixed capacitor)..;.

od395781/2022_2023 : LIFT Distribution Board.SITC of Sub Main Distribution Board with Isolator incomer and MCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle. Incomer : 63A,TPN Isolator with indication lamp- 1Nos. Busbars: 63A Aluminium, 25X3 mm cu for Earth Outgoings: 40/63A, 4P, RCCB, 100mA - 1No.25A, 2P, RCCB, 30mA - 1No.10A, 1P, B Curve, MCB - 4Nos

Distribution Board / RCCB / ISOLATOR / MCBs 2.3.1 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator6 way, Double door

2.3.2 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.3.3 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.5.1 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

2.5.2 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

2.5.3 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.2 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and netural

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.12.2 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.3 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

2.14.1 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.3 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.1 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.16 : Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

2.17 : Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

2.18 : Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.19 : Supplying and fixing 20 amps 415volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 amps "C" curve, TPMCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.20 : Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.21 : Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

2.22 : Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

2.23.4 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. 2For 14 way, Double door SPN MCBDB

2.24.1 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 4 way, Double door TPN MCBDB

2.24.2 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 6 way, Double door TPN MCBDB

2.24.3 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 8 way, Double door TPN MCBDB

od381985/2022_2023 : Supply and fixing 8 way (8 + 24) double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

od381986/2022_2023 : 63 A rating, 4 pole, 100 mA RCBO

od381987/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, range upto 300 mA, RCCB, in the existing MCB DB complete with connections, testing and commissioning etc. as required. .25/32 A rating, 4 pole, 30 mA RCCB

od381988/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, range up to 300mA, RCCB, in the existing MCB DB complete with connections, testing and commissioning etc. as required. .40 A rating, 4 pole, 30 mA RCCB

od381989/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 30mA, RCCB, in the existing MCB DB complete with connections, testing and commissioning etc. as required. .63 A rating, 4 pole, 30 mA RCCB

od381990/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 30mA, RCCB, in the existing MCB DB complete with connections, testing and commissioning etc. as required. .100 A rating, 4 pole, 100 mA RCCB

od381992/2022_2023 : MCCB VDB:- SITC of vertical Distribution Panel Board with MCCB incomer and TP MCB outgoing, Incomer : 100/125A, MCCB -1 no Busbars: 125A Al bus bars, 25X3 mm cu for Earth Outgoings: 40/63A, 4P, C Curve, MCB - 6 Nos

od381993/2022_2023 : Supplying and fixing 415 volts, .;C.; curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole 40 A MCB

od381994/2022_2023 : Supplying and fixing 415 volts, .;C.; curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required..Triple pole 63 A MCB

MV cable Laying od381881/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 400 Sq.mm.

od381885/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 300 Sq.mm.

od381888/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE).3.5C x 240 Sq.mm.

od381891/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 185 Sq.mm.

od381898/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 150 Sq.mm.

od381900/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 120 Sq.mm.

od381907/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 95 Sq.mm.

od381909/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 70 Sq.mm.

od381916/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE).3.5C x 50 Sq.mm.

od381922/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .3.5C x 35 Sq.mm.

od381925/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .4C x 25 Sq.mm.

od381931/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .4C x 16 Sq.mm.

od381935/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .4C x 10 Sq.mm.

od381940/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .4C x 6 Sq.mm.

od381944/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) .4C x 4 Sq.mm.

od381957/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE).1Rx 3C x 1.5 Sq.mm.cu

od381961/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V .4C x 6 Sq.mm

od381963/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V .4C x 4 Sq.mm

od381966/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V .1C x 10 Sq.mm

od381967/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V.6C x 1.5 Sq.mm.

od381972/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering andrefilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm

7.1.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.5.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm

7.5.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 95 sq. mm and upto 185 sq. mm

7.5.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.9 : Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

7.10 : Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

CABLE END TERMINATION 9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.30 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.31 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.35 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 35 sq. mm (32mm)

od381950/2022_2023 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required .1x 3C x 1.5 Sq.mm.

od381956/2022_2023 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required .6C x 1.5 Sq.mm

od381960/2022_2023 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required .12C x 1.5 Sq.mm

WIRING 1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.54.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire

1.14.5 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 10 sq. mm + 1 X 6 sq. mm earth wire

1.14.6 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 16 sq. mm + 1 X 6 sq. mm earth wire

1.14.7 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

1.14.8 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 4 sq. mm + 2 X 4 sq. mm earth wire

1.14.9 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.14.10 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.14.11 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 16 sq. mm + 2 X 6 sq. mm earth wire

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.2 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.27.6 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.28.1 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.3 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module

1.28.4 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module

1.28.5 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module

1.28.6 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.12 Module

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

od381984/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 &amp; 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required..

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.34 : Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.35 : Erection of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

1.56 : Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

od381991/2022_2023 : Supply &amp; Fixing of Computer points with 3 Nos 3 pin 5.6 A Socket with 3 Nos 5/6 A switch with modular front plate and cover on surface/recess, including providing and fixing suitable size GI boxes, its interconnections etc, as required complete.

CABLE TRAY 4.1.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.1.3 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.10 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X 62.5 mm depth X 2.0 mm thickness

4.1.11 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 62.5 mm depth X 2.0 mm thickness

EARTHING 5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

5.4 : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.6 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.10 : Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

5.14 : Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.17 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

5.20 : Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

od381905/2022_2023 : Supply and installation charges for Providing 1200x 1200x12 mm Cast Iron plate earth station, conforming to IS 3043 filling with mixtures of salt, sand and charcoal, construction of earth chamber with brick masonry and covering with heavy duty Cast Iron Cover hinged to Cast Iron Frame, including excavation &amp; backfilling of earth pit.

od381913/2022_2023 : Supplying and laying 40mm x6mm copper strip at 0.50 metre below ground as strip earth electrode,including connection / terminating with nut,bolt,spring,washer etc.as required.(jointing shall be done by overlapping and with 2 sets of brass nut bolt &amp; spring washer spaced at 50mm)

od381915/2022_2023 : Supplying and laying 32mm x6mm copper strip at 0.50 metre below ground as strip earth electrode,including connection / terminating with nut,bolt,spring,washer etc.as required.(jointing shall be done by overlapping and with 2 sets of brass nut bolt &amp; spring washer spaced at 50mm)

od381923/2022_2023 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.

od381926/2022_2023 : Providing and fixing 32mm x 6mm copper strip on surface or in recess for connections etc as required.

od381930/2022_2023 : Providing and fixing 6 SWG dia Copper. wire on surface or in recess for loop earthing as required.

od381936/2022_2023 : Providing and fixing 10 SWG dia Copper wire on surface or in recess for loop earthing as required.

LIGHTNING CONDUCTOR 6.2 : Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

90.16.3.17 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)20 x 3 mm aluninium strip

90.16.4.14 : Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required ( for vertical run).20 x 3 mm aluminium strip

6.14 : Providing and laying G.l. tape 32 mm X 6 mm from earth. electrode directly in ground as required.

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

od381897/2022_2023 : Providing and fixing test joint box using SMC/FRP enclosure for connecting 32 x6 mm GI strip and 20 mm X 3 mm thick G.I. strip,including test joint,busbar suppory

LIGHTING FIXTURES od402338/2022_2023 : Supply and fixing of LED Recessed mount down light with 28W/30W,600X600MM with System efficiency of more than 100 lm/W and Translucent frosted diffuser for Uniform illumination and wider light distribution. The LED shall be compliant with life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CT of 5700k and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 140V to 270V..

od402339/2022_2023 : Supply and fixing 18W, 220x220mm, IP20, LED surface/Recess mounted down light with Maximum system wattage of 18 W, System efficiency >=-100lm/W and minimum system lumen output 1800 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.9 with inbuilt Surge Protection of 2.5KV.

od402340/2022_2023 : Supply and fixing of 18W, IP20,LED Recess /surface mounted Round downlighter with Maximum system wattage of 18 W, System efficency >=100lm/W and minimum system lumen output 1200 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.9 with inbuilt Surge Protection of 2.5KV.

od402341/2022_2023 : Supply and fixing of 12W, IP20,LED Recess /surface mounted Round downlighter with Maximum system wattage of 12 W, System efficency >=100lm/W and minimum system lumen output 1200 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.9 with inbuilt Surge Protection of 2.5KV.

od402342/2022_2023 : Supply and fixing of 6W, IP20,LED Recess /surface mounted Round downlighter with Maximum system wattage of 6 W, System efficency >=100 lm/W and minimum system lumen output 1200 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.9 with inbuilt Surge Protection of 2.5KV.

od402343/2022_2023 : Supply and fixing 20W IP20 High efficient 1.2m long LED batten surface/wall mounted Specially designed Co-extruded channel in thermally conductive material with plastic with HET diffuser. In-built electronic driver duly wired up to terminal block. CRI &gt;80, Temperature range-0 to 50DegC, Driver efficiency&gt;85%, Power factor&gt;0.9, CT - 6500K, THD&lt;20%, Surge protection 2kV, 30000 burning hours Luminaire lumen &ge; 2200 lumens (110 lm/W).

od402344/2022_2023 : Supply and fixing of 10W IP20 High efficient 0.6m long LED batten surface/wall mounted Specially designed Co-extruded channel in thermally conductive material with plastic with HET diffuser. In-built electronic driver duly wired up to terminal block.IP20, CRI &gt;80, Temperature range-0 to 50DegC, Driver efficiency&gt;85%, Power factor&gt;0.9, CCT - 6500K, THD&lt;20%, Surge protection 2kV, 30000 burning hours Luminaire lumen &ge; 1000 lumens (100lm/W)..

od402345/2022_2023 : Supply and fixing of street light luminare of 18/20W outdoor, Integral, SMD LED, IP 65, LED Surface mounted Die cast Alumium body with System efficacy of more than 100 lm/W. LED luminaire shall have specially design aluminum heat sink for excellent heat dissipation, good air circulations as well as very light weight.The luminaire should have inbuilt SPD -2.5KV with CRI more than 70, Power factor 0.9 , THD less than 10%. including providing and fixing of bracket made of 25mm GI tube length 1m , wiring etc complete. .

od402346/2022_2023 : Supply and fixing Wall-recessed LED foot light in the existing GI box..

od402347/2022_2023 : Supply of Integral, SMD LED, IP 66, 9W, LED Surface mounted Die cast Alumium Bulk head fixture with System efficacy of more than 70 lm/W. Luminaire shall have Polycarbonate high transmitivity diffuser for Uniform illumination and wider light distribution. LED luminaire shall have specially design aluminum heat sink for excellent heat dissipation, good air circulations as well as very light weight.The luminaire should have inbuilt SPD -2.5KV with CRI more than 70, Power factor 0.9 , THD less than 10%..

od402348/2022_2023 : Supply and fixing of weather proof, 3D signage board 1m height and 4 m wide fabricated with Angle iorn strucure and 14SWG CRCA sheet, fixing of 3D, letters made using 2mm thick acrylic sheet, each lettee is illuminated with sufficient LED rope including 12V dc power controller for LED ( each letter consist two layer LED as approved ).

od402349/2022_2023 : Supply installation testing and commisioning of 6M long, 100/80mm dia GI tubular pole, with 2m long arm single/double bracket of sutable size, including providing and fixing 30W, IP 67, LED light fittings, SMC junction box, fuse, connector, wiring from junction box to light fittings, providing conctreate foundation with foundation bolt etc .

od402350/2022_2023 : Supplying and fixing 225mm sweep heavy duty exhaust fan in metal frame working on 230V, with more than 300cmHh air delivery.The work shall include making the holes suitable for the size of fan, fixing necessary bolt and nuts making good the damages, etc. and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required..

od402351/2022_2023 : Supply, Installation, Testing and Commissioning of 1200 MM sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) motor, class of insulation:B, 3 nos blades, 30 cm long down rod, 2 nos canopies, shackle kit, saftey rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery minimum 215 CM/M, 350 RPM, (tolerance as per IS:374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including saftey pin, nut, bolts, washers, temperature rise = 75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required..

od402352/2022_2023 : Supply and fixing 9 W LED Light in th existing angle batten holder.

MISCELLANEOUS ITEMS 14.13.1 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required50 mm dia

14.13.2 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required80 mm dia

14.13.3 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required100 mm dia

14.13.4 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required150 mm dia

14.15.3 : Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.120 mm dia (OD-120 mm & ID-103 mm nominal)

14.15.4 : Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.160 mm dia (OD-160 mm & ID-135 mm nominal)

od381903/2022_2023 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 &amp; 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base ,lid ,cable divider,End cap all accessories in complete as per site conditions.

od381906/2022_2023 : Supply and laying of synthetic Electrical grade mat .Providing ISI marked electrical 11kV. Grade 2m x 1m x 2.5 mm thick anti-skid insulation mat as per IS: 15652 class B

od381911/2022_2023 : Supply and laying of synthetic Electrical grade mat .Providing ISI marked electrical 1.1kV. Grade 2m x 1m x 2 mm thick anti-skid insulation mat as per IS:15652 class A

od381918/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.32A TPN Isolator

od381920/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.32A DP Isolator

od381924/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.40A DP Isolator

od381937/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.63A TPN Isolator

od381941/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.100A TPN Isolator

od381942/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.200A TPN Isolator

od381948/2022_2023 : Supply and fixing of following isolators in sheet steel powder coated enclosure with space for loose cable and door interlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.250A TPN Isolator

od381952/2022_2023 : Supply and fixing of 40/63 A ,100 mA ELCB in suitable size outdoor weather proof- IP66 sheet steel powder coated enclosure with door interlock facility on surface confirming with all accesories,space for termination of cables, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.

od381955/2022_2023 : Supply and installation of emergency OFF trip push button with front Glass and painted in RED Colour.

od381959/2022_2023 : Supply conveyance, installation, testing and commissioning of PIR occupancy sensors for controlling lights with NO/NC contacts.

od381965/2022_2023 : Supply of 11kV grade hand glovess.

od381968/2022_2023 : Supply, Installation, Testing and Commissioning of Aviation Obstruction Lamp with flasher unit (LED type ).

od381970/2022_2023 : Supply fabrication, painting with two coats of synthetic enamel paint over a coat of zink chromate primer and erection of MS structural steel ( Angle iron/ flats/T section) for supporting the equipments, exhaust line etc complete.

od381973/2022_2023 : Supply and Installation of 1.2mm thick Gl trunking with cover.100x50mm wide

od381976/2022_2023 : Supply and Installation of 1.2mm thick Gl trunking with cover.150x50mm wide

od381977/2022_2023 : Supplying of 6mm thick MS chequered plates with frame duly painted. Plates to be cut size as per site requirement.

od381979/2022_2023 : Supplying, Fixing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

od381980/2022_2023 : Providing and fixing extra conduit down rod MS pipe of 20 mm dia, 2X10 cm length wiring with 2 X1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored).

od381981/2022_2023 : Supplying and fixing extra down rod of 10 cm length MS pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored).

od381982/2022_2023 : Supply of all equipments, design, installation,testing, commissioning and training of Smart energy measurment system, including accessories like, energy meters, water meters, transducers, indicators, controll cabling, communicable equipments etc for measuring various energy input sources(KSEB power, DG sets, solar power system, etc) and water input sources ( muncipal water, open well, tube well etc) for measuring input energy and water system processing the data with predefined parameters analysing the data , provide optimam output result for reducing the energy and water resources.All data cabling, input ouput devices, power supply module, DC source with battery, server, softwares, etc included in this system. It must have Service Oriented Architecture-based integration, Load management based on business rules, data management, outage management system, peak load management system, etc. Meter is to be SCADA, BMS and DMS compatible. Real Time data acquisitions and analysis, control of field electrical equipment, managing electricity flow and maintaining safety, load flow analysis, state estimation, demand forecast, Capable to manage large data, ensure data security and integrate with various sub-systems including legacy systems. automation solutions for accounting renewable energy into the grid, operational details of DG set etc.

od381983/2022_2023 : Supply and installation of Laminated copies of Approved/ as built schemes and drawings in electrical room.

CONDUITS AND SLEEVES 1.21.1 : supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 : supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

14.15.1 : supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.63 mm· dia (OD-63 mm & ID-51 mm nominal)

od371734/2022_2023 : 32 mm dia (OD-32 mm &amp; ID-26 mm nominal).

od347101/2022_2023 : supply and fixing of 25mm dia MS flexible pipe with pvc coating along with all ancillaries and accessories like coupler etc as required

4.6.2 : supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.3 : supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

od347122/2022_2023 : supply and installation of 1.2x150x50mm GI trunking with cover&lt;br&gt;

od347124/2022_2023 : supply and installation of 1.2x100x50mm GI trunking with cover&lt;br&gt;

1.53.1 : supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.53.2 : supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required2 run of Cable

1.53.3 : supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required3 run of Cable

1.27.1 : supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

od347135/2022_2023 :.supplying and fixing PVC boxes of sizes 200x100mm on surface with suitable size of sheet cover (white colour) in front etc required.

NETWORKING od347115/2022_2023 :.supply and laying of 6 Core OS2 SM Central Loose Tube Armored Indoor / Outdoor Cable through the existing PVC conduit including splicing and termination at both ends etc. complete.

1.28.1 : supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2 : supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

od347123/2022_2023 :.supply, installation, testing and commissioning of I/O point with single RJ45 outlets, in existing back box including IDC crimping etc. complete (data/cctv).

od347125/2022_2023 : supply, installation, testing and commissioning of I/O point with dual RJ45 outlets, in existing back box including IDC crimping etc. complete (data/cctv).

od347126/2022_2023 :.supply installation testing and commissioning of Patch cord - 2mtr.

od347127/2022_2023 :.supply installation testing and commissioning of Patch cord - 1mtr.

od347128/2022_2023 :.supply installation testing and commissioning of Pigtail SC SM simplex length 1 Metre.

od347129/2022_2023 : supply installation testing and commissioning of 19", 42U, 800X1000mm Depth Floor Mount Network Rack with Front Glass Door, Horizontal Cable Manager, Horizontal PDU, 12 round pin sockets - 2 No, Cooling Fan, Mounting Hardware Screws with all mechanical supports etc. complete

od347116/2022_2023 : supply installation testing and commissioning of floor mount 22 U Network Rack 600 mm X 600 MM with cable manager, PDU 6 Socket, Cable Organizer 1U Closed, Fan &amp; Hardware Kit and all other accessories etc. complete

od347130/2022_2023 : supply installation testing and commissioning of 19",9U, 600 MM Depth Wall Mount Rack with Front Glass Door, Horizontal Cable Manager, Horizontal PDU, 6X5Amps - 1 No, Cooling Fan with necessary Mounting Hardware Screws with all mechanical supports etc. complete

od347132/2022_2023 : supply, Installation, Testing and Commissioning of 24-Port Gigabit L2 Managed Switch with 4 SFP Slots Gigabit Ethernet connections on all ports provide full speed of data transferring L2+ feature Static Routing, helps route internal traffic for more efficient use of network resources IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X Authentication and Radius provide you robust security strategies L2/L3/L4 QoS and IGMP snooping optimize voice and video application IPv6 support with dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery Web, CLI (Console Port, Telnet, SSH), SNMP, RMON and Dual Image bring abundant management policies.

od347133/2022_2023 :.supply, Installation, Testing and Commissioning 16-Port Gigabit L2 Managed Switch with 16-Port PoE+ 384 W PoE Budget: 24&times; 802.3at/af-compliant PoE+ ports with a total power supply of 384 W*. Full Gigabit Ports: 16&times; gigabit PoE+ ports and 4&times; gigabit SFP Slots provide high-speed connections, Centralized Cloud Management, and Intelligent Monitoring.Centralized Management: Cloud access for ultra convenience and easy management. Static Routing: Helps route internal traffic for more efficient use of network resources. Robust Security Strategies: IP MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X, Radius Authentication, and more. Optimize Voice and Video Applications: L2/L3/L4 QoS and IGMP snooping. Standalone Management: Web, CLI (Console Port, Telnet, SSH), SNMP, RMON, and Dual Image bring powerful management capabilities.

od347137/2022_2023 : supply installation testing and commissioning of 8-Port Gigabit Smart PoE + Switch with 2 SFP Slots Features 8 802.3af/at compliant PoE + ports, with total PoE power budget of 116W and useful PoE power management features Gigabit Ethernet connections on all ports provide full speed of data transferring Advanced security features include IP?MAC-Port Binding, ACL, Port Security, DoS Defend, Storm Control, DHCP Snooping, 802.1X, and Radius Authentication L2/L3/L4 QoS and IGMP snooping optimize voice and video applications WEB/CLI managed modes, SNMP, RMON bring abundant management features Dual Firmware Image improves reliability and up-time of network

od347138/2022_2023 :.supply, installation, testing and commissioning of Server PC, Intel i7 processor 12 th generation, 24 inch LED monitor, Gigabit LAN port, USB port, 16GB, 16Gx1, DDR4, 2933MHz,256GB M.2 PCIe NVMe Solid State Drive + 1TB 7200 rpm 3.5&quot; SATA Hard Drive,2GB dual graphic card, 100/1000 LAN ports, optical mouse, Keyboard, DVD Writer. Genuine Windows 10 (with latest updation for the system) Home 64-bit English, 24 inch LED monitor, Mouse, keyboard, speaker set.

od347139/2022_2023 : Providing and termination of CE Listed 19&"; Easy Front Access (EFA) Sliding Rack Mount duplex type 24 Port LIU with modules splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc complete.

od347140/2022_2023 : Providing and termination of CE Listed 19" Easy Front Access (EFA) Sliding Rack Mount duplex type LIU 06 Port Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc complete

od347141/2022_2023 : supply installation testing and commissioning of Cat 6/Cat 6A 24 Port fully-loaded patch panel with rear cable manager and necessary mechanical supports etc. complete.

od347142/2022_2023 :.supply installation testing and commissioning of Cat 6/Cat 6A 16 Port fully-loaded patch panel with rear cable manager and necessary mechanical supports etc. complete.

od347143/2022_2023 :.supply installation testing and commissioning of Cat 6/Cat 6A 8 Port fully-loaded patch panel with rear cable manager and necessary mechanical supports etc. complete.

od347144/2022_2023 : supply installation testing and commissioning of SFP Module 1 G

WIRELESS NETWORK SYSTEM od347071/2022_2023 : supply, installation, testing and commissioning of Wireless Dual Band Ceiling Mount Access Point Ultra-Fast Wi-Fi 6 Speeds: Simultaneous 574 Mbps on 2.4 GHz and 1201 Mbps on 5 GHz totals 1775 Mbps Wi-Fi speeds. High-Density Connectivity: 4&times;increased capacity to connect more devices simultaneously. Integrated into SDN: Zero- touch&lt;br&gt;Provisioning (ZTP), Centralized Cloud Management, and Intelligent Monitoring. Centralized Management: Cloud access and app for ultra convenience and easy management. Seamless Roaming: Even video streams and voice calls are unaffected as users move between locations. PoE+ Support: Supports Power over Ethernet (802.3at) for convenient deployment and installation. Secure Guest Network: Along with multiple authentication options (SMS/Wi-Fi/ Voucher, etc.) and abundant wireless security technologies.

od373806/2022_2023 :.supply, Installation, Testing and Commissioning of controller for the wireless access points capable of centralized management up to 100 access points, jet stream switches and Safe stream routers, cloud access, L3 management, multi site management, Automatic Device Discovery, Batch Configuration, Batch Firmware Upgrading, Intelligent Network Monitoring, Abnormal Event warnings, Unified Configuration, Reboot Schedule, Captive Portal Configuration with Ethernet Cable, Power Cord and Rackmount Kit, including providing and commissioning of necessary software for WIFI Hotspot management solution for 100 users.

CLOSED CIRCUIT TELEVISION (CCTV) SYSTEM od347069/2022_2023 : supply, Installation, testing and commissioning of 2 MP IR DOME , 1/2.8&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 2MP (1920 &times; 1080)@30 fps H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 50 m ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and storage environments Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes Intelligent detection: Intrusion, tripwire (support the classification and accurate detection of vehicle and human) Abnormality detection: Motion detection, video tampering, scene&lt;br&gt;changing, audio abnormality detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, voltage detection Alarm: In, out; Audio: In, out; Supports max. 256 G Micro SD card 12V DC/POE power supply, IP67, IK10 protection, SMD Smart Motion Detection Certification, CE,FCC, UL, BIS

od347070/2022_2023 : 4MP Bullet , 1/3&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 4MP (2688 &times; 1520)@30 fps, H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 50 m.ROI, SMART .264+/H.265+, flexible coding, applicable to various&lt;br&gt; bandwidth and storage environments. Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes. Intelligent detection: Intrusion, tripwire (support the classification and accurate detection of vehicle and human) Abnormality detection: Motion detection, video tampering, scene&lt;br&gt;changing, audio detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, voltage detection Supports max. 256 G Micro SD card, built-in Mic 12V DC/POE power supply IP67 protection SMD Smart Motion Detection Certification, CE,FCC, UL,BIS

od347079/2022_2023 : supply, Installation, Testing and Commissioning of 4MP VARIFOCAL 2.7 mm&ndash;13.5 mm, F-1.5, field of range Horizontal: 104&deg;&ndash;27&deg;,Vertical: 55&deg; &ndash; 15&deg;&lt;br&gt;Diagonal: 124&deg; &ndash;31&deg;. 1/3&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 4MP (2688 &times; 1520)@30 fps H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 60 m ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and&lt;br&gt;storage environments Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes Intelligent detection: Intrusion, tripwire Abnormality detection: Motion detection, video tampering, scens changing, audio abnormality detection, no SD card, SD card full, SD&lt;br&gt;card error, network disconnection, IP conflict, illegal access, voltage detection Alarm: In, out; Audio: In, out; Supports max. 256 G Micro SD card 12V C/POE power support IP67, IK10(optional) protection SMD Smart Motion Detection Certification, CE,FCC, UL

od347083/2022_2023 : supply, installation, testing and commissioning 32 Channel Network Video Recorder 32-channel IP video access Smart H.265+/Smart H.264+/H.265/H.264/MJPEG; H.265 auto switch Max 320 Mbps incoming bandwidth Up to 24MP resolution for live view and playback 1-channel fisheye dewarping (AI by NVR) AI by Camera: Perimeter protection; face detection and recognition; SMD Plus; video metadata; ANPR; people counting; stereo analysis; crowd distribution; heat map . Up to 22 face pictures/sec processing&lt;br&gt;&middot; Up to 20 face databases with 100,000 face images in total. Smart H.265+ is the optimized implementation of the H.265&lt;br&gt;codec that uses a scene-adaptive encoding strategy, dynamic GOP, dynamic ROI, flexible multi-frame reference structure and intelligent noise reduction to&lt;br&gt;deliver high-quality video without straining the network. ANPR Automatic Number Plate Recognition required for convenient entrance/ exit management. Support license plate recognition black/white list import/export, add/remove B/W list number, search result from recorded video. Internal HDD 8 SATA III Ports, Up to 10 TB capacity for each HDD eSATA 1 eSATA Interface 2 RJ-45 Ports (10/100/1000Mbps)Independent or Joint Working PoE N/A Network Function HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, SNMP, RTSP,UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE, DDNS,FTP, Alarm Server, IP Search (Support IP camera, DVR, NVS, etc.), P2P Max. User Access 128 users Smart Phone iPhone, iPad, Android Interoperability ONVIF 2.4, SDK, CGI Certification CE,FCC,UL,BIS

od347093/2022_2023 : supply, installation, testing and commissioning of 24 Port GIGA POE switch with 4 SFP Module. Jet Stream 24-Port Gigabit Smart PoE+ Switch with 4 SFP Slots Supports 24 802.3at/af-compliant PoE+ ports with a total power supply of 192W L2+ Feature&mdash;&mdash;Static Routing, helps route internal traffic&lt;br&gt;for more efficient use of network resources IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X and Radius Authentication provide you robust security strategies L2/L3/L4 QoS and IGMP snooping optimize voice and video applicationsIPv6 support with dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery WEB/CLI managed modes, SNMP, RMON and Dual Image bring abundant management features&lt;br&gt;

od347098/2022_2023 :.supply, installation, testing and commissioning of 16 Port GIGA POE switch with 4 SFP Module. Jet Stream 24-Port Gigabit Smart PoE+ Switch with 4 SFP Slots Supports 24 802.3at/af-compliant PoE+ ports with a total power supply of 192W L2+ Feature&mdash;&mdash;Static Routing, helps route internal traffic for more efficient use of network resources IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X and Radius Authentication provide you robust security strategies L2/L3/L4 QoS and IGMP snooping optimize voice and video applicationsIPv6 support with dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery WEB/CLI managed modes, SNMP, RMON and Dual Image bring abundant management features.

od347102/2022_2023 : supply, installation, testing and commissioning of 8 port- PoE switch with 2 SFP Module Gigabit Smart Switch is equipped with 8 gigabit RJ45 ports and 2 SFP slots, all RJ45 Ports support the 802.3af/at (PoE+) standard with total PoE power budget of 60W and useful PoE power management features. The switch provides high performance, enterprise-level QoS, useful security strategies and rich layer 2 management features. TP-Link&rsquo;s Jet Stream Gigabit Smart Switch is especially designed for the small and medium business networks that require efficient network management. The switch comes with a comprehensive set of features, such as Link Aggregation Group, 802.1Q VLAN, Access Control Lists (ACL), Quality of Service (QoS L2 to L4), Storm Control and IGMP Snooping to provide a small or medium-sized business with a network that is geared for growth while ensuring performance and reliability. What&rsquo;s more, its easy-to-use web management interface means faster setup and configuration with less downtime

od347104/2022_2023 supply, Installation, Testing and Commissioning of 24 port fully loaded Patch panel with necessary mechanical supports.

od347108/2022_2023 :.supply, Installation, Testing and Commissioning of 16 port fully loaded Patch panel with necessary mechanical supports.&lt;br&gt;

od347110/2022_2023 :.supply, Installation, Testing and Commissioning of 8 port fully loaded Patch panel with necessary mechanical supports.&lt;br&gt;

od347114/2022_2023 : supply, Installation, Testing and Commissioning of fully loaded 12 port LIU

od347120/2022_2023 : supply, installation, testing and commissioning of Surveillance/SATA compatible Hard Disk of 8 TB capacity to achieve the total storage for 30days @ 20fps for the NVR server

od347121/2022_2023 : supply, Installation, Testing &amp; Commissioning of 55&apos;&apos; 4K LED Monitor with resolution 3840x2160 pixel including wall mounting accessories.

PUBLIC ADDRESS SYSTEM od347078/2022_2023 : supplying, installation, testing & commissioning of 6W ceiling speaker complete as required

od347082/2022_2023 : supplying, installation, testing &; commissioning of ceiling/wall mounted loud speaker, 6 Watt in ABS enclosure complete as required.

od347091/2022_2023 : supply, installation, testing and commissioning of Voice Alarm Controller having all Heart of the Plena Voice Alarm System EN 54- 16 certified and EN 60849 compliant. Message manager and 240 W amplifier built-in Six-zone outputs 12 business and emergency control inputs Voltage 230/115VAC,&lt;br&gt;&plusmn;15%, 50/60 Hz Current inrush 8 A Max power consumption 600 VA. Voltage 24 VDC, +15% / -15% Current max 14 A. Output power (rms/maximum) 240 W /360 W Power reduction on backup power -1 dB. Frequency response 60 Hz to 18 kHz (+1/-3 dB at -10 dB ref. rated output) Distortion &lt;1% at rated output power, 1 kHz Bass control -8/+8 dB at 100 Hz Treble control -8/+8 dB at 10 kHz Mic/line input 1 x Connector XLR, 6.3 mm jack Sensitivity 1 mV (mic), 1 V (line) Impedance &gt;1 k ohm (mic); &gt;5 k ohm (line)S/N (flat at max volume) &gt;63 dB (mic); &gt;70 dB (line).S/N (flat at min volume/muted) &gt;75 dB CMRR &gt;40&lt;br&gt;dB (50 Hz - 20 kHz).Headroom &gt;25 db. Speech filter -3 dB at 315 Hz, high-pass, 6 dB/oct

od347094/2022_2023 : supply, installation, testing and commissioning of Voice alarm Router to expand the Plena Voice Alarm System with six zones. EN 5416 certified.12 additional input contacts Six volume override output contacts. Supervision within the Plena Voice Alarm System Router

od373954/2022_2023 :.supply, installation, testing &amp; commissioning of 240 watts amplifier XLR inputs / output, Direct 100V input for power expansion, Excellent S/N &gt;85dB, Input level control, Low profile 2U housing, Low impedance output for 8 or 4 ohms output, microphone with cable, jack, connectors etc

od347107/2022_2023 : supply, installation, testing and commissioning of Booster Amplifier 480 W

od347111/2022_2023 : supply, installation, testing &amp; commissioning of DVD player for background Music

od347112/2022_2023 :.supplying drawing and testing of Single pair, multi stranded, 0.75 sq mm Fire Retardant PVC insulated tinned copper conductor sheilded speaker cable in the existing surface, surface/recessed pvc conduit including connections and interconnections etc. as required

od347113/2022_2023 : supply and laying of 18AWG tinned copper sheilded (XLR) microphone signal cable including connecting jack&lt;br&gt;

CABLE TELEVISION SYSTEM 1.19 : supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

od347074/2022_2023 : supplying and drawing co-axial RG-11 copper cable in the existing surface/recessed steel/ pvc/hdpe conduit as required.&lt;br&gt;

1.24.7 : supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

od347085/2022_2023 : Cable TV connection from operator which includes supply, installation, testing and commissioning of all accessories (including the set top box, antenna, amplifier whichever is required) for making the cable TV connection to the Television point

od347087/2022_2023 :.supply, Installation, Testing and Commissioning of 55 inch LED SMART TV with necessary supports/stands etc. complete&lt;br&gt;

od347095/2022_2023 :.supply, Installation, Testing and Commissioning of 32 inch LED SMART TV with necessary supports/stands etc. complete&lt;br&gt;

TELEPHONE SYSTEM 1.18.2 : supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

od347075/2022_2023 :.supply, Installation, Testing and Commissioning of 20 pair Telephone &amp; Switchboard cable with high density polyethylene insulated solid annealed high conductivity bare copper with dia 0.50 M paired polyester taped and sheathed with high oxygen index, fire retardant PVC Compound, generally confirming to ITD specifications

od347080/2022_2023 :.supply, Installation, Testing and Commissioning of 50 pair Telephone &amp; Switchboard cable with high density polyethylene insulated solid annealed high conductivity bare copper with dia 0.50 M paired polyester taped and sheathed with high oxygen index, fire retardant PVC Compound, generally confirming to ITD specifications

od374831/2022_2023 :.supply, Installation, Testing and commissioning of 20 pair Krone module fixed in box

od374948/2022_2023 :.supply, Installation, Testing and commissioning of 50 pair Krone module fixed in box

od347109/2022_2023 : supply, Installation, Testing and Commissioning of 200 pair MS DP box with tele connector

1.24.6 : supplying and fixing following modular type switch / socket on the existing switch box/ cover including connections etc. as required.Telephone socket outlet

od347117/2022_2023 :supply, Installation, Testing &amp; Commissioning of EPABX System, configured for 6nos trunk lines and 240extensions(expandable upto 240 ports)DIGITAL VOICE MODULES - 08 OF 16 SECONDS EACH,AUDIO CONFERENCE &ndash; 15 PARTY,EXTERNAL MUSIC PORT &ndash; 1,PUBLIC ADDRESS SYSTEM PORT &ndash; 1,COMMUNICATION PORTS(RS-232 ),DIGITAL IN-PUT PORT( FOR SENSORS) &ndash; 1,DIGITAL OUT-PUT PORT ( FOR CONTROL) &ndash;1 &amp; ASMDR SOFTWARE FOR OUTGOING,INCOMING(INCLUDING MISSED CALLS &; INTERCOM CALL ).

od347118/2022_2023 :.supply, installation, testing and commissioning of I/O point with single RJ 11 outlets, in existing back box including IDC crimping etc. complete (data/cctv)&lt;br&gt;

od347119/2022_2023 :.supplying, installation, testing &amp; commissioning of ordinary telephones with connecting cords (minimum length of 2 metres) having necessary connector at both ends

ACCESS CONTROL SYSTEM od347072/2022_2023 :.supply of smart cards for the access.

od347077/2022_2023 : supply installation testing and commissioning of Proximity card readers

od347084/2022_2023 : supply, installation, testing and commissioning of 4 Door / 8 Reader Controller: Supports access control of up to 4 doors in all respect including 4 entry readers, 4 exit readers, 4 locks, 4 exit switches etc. Inbuilt RJ45 Network Interface: Leveraging on the merits of IP based systems; it can easily be hooked up on the existing TCP/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware: Facility to onsite upgrade the firmware over Ethernet interface so that any customization or new version can be easily upgraded without any need of removing the device. Protected Enclosure: Both controller &amp; power supply unit are protected with suitable housing so that electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back: Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking: Facility of door interlocking is available. The system allows creating a group of doors such that access to a door within the group is allowed only when all the other doors are in closed condition

od347086/2022_2023 : supply, Installation, Testing and Commissioning of Push Button switch with accessories

od347089/2022_2023 : supply, Installation, Testing and Commissioning of Electromagnetic Lock with required mounting brackets etc. complete for single door/double door

od347092/2022_2023 : supply, Installation, Testing and Commissioning of surface / flush mounted (as required at site) Magnetic Contact (Door position sensor) for access controlled doors

od347096/2022_2023 : supply and laying of 4 core 0.75 Sq. mm Un Armored FRLS, Multi stranded Copper Conductor, PVC sheathed Cable for connecting controller to Lock &amp; door position sensors, Buzzer, BGU, Push button etc. complete

od347100/2022_2023 : supply and laying of 8 core 0.75 Sq. mm Un Armored FRLS, Multi stranded Copper Conductor, PVC sheathed Cable for connecting controller to Lock &amp; door position sensors, Buzzer, BGU, Push button etc. complete

od347105/2022_2023 : supply installation, testing, commissioning of EDR (EMERGENCY BREAK GLASS )

NURSE CALL SYSTEM od380721/2022_2023 : supply installation testing and commissioning Addressable Microprocessor Control Nurses Call Station Monitor with necessary software and control module with display and a soft buzzer. Information displayed in 5 digit, when more then one call is registered, then the information shall be scrolled. Power supply suitable for 220V 50 hz AC main supply complete with step-down transformer of appropriate rating ,required power supply with dc backup, network interface module, power supply and complete as per specification required. The Staff Console shall have a 7&quot; capacitive touch backlit color LED screen.

od347076/2022_2023 : supply, Installation, Testing &amp; Commissioning of Bedside modules comprising of Nurse call, cancel &amp; Wait,Code blue buttons hand held unit and input jack for hand held module including providing and fixing of 1.6 mm thick GI box complete as per specifications.

od347088/2022_2023 :.supply, Installation, Testing and Commissioning of toilet bath station with pull cord.

VRF INDOOR UNITS od338019/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 3.0 TR/1200 CFM,TSP-30mm

od338239/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 4.0 TR/1600 CFM,TSP-30mm

od338020/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 5.0 TR/2000 CFM,TSP-40mm

od338021/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 6.0 TR/2400 CFM,TSP-40mm

od338022/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 8.0 TR/3200 CFM,TSP-50mm

od338854/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.(VRF) 9.0 TR/3600 CFM,TSP-50mm

od338855/2022_2023 : High Wall Unit:-Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality ,auto restart and multimode.(VRF) .1.5 TR/600 CFM

od338856/2022_2023 : High Wall Unit:-Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality ,auto restart and multimode.(VRF) .2 TR/800 CFM

MECHANICAL VENTILATION AND EXHUAST FANS od340402/2022_2023 : Circular type inline fan for ducted exhaust air application consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation for with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 400 cfm , ESP - 20 mm

od340403/2022_2023 : Circular type inline for ducted exhaust air application fan consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation for with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 500 cfm , ESP - 20 mm&lt;br&gt;

od340404/2022_2023 :Circular type inline fan for ducted exhaust air application consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 600 cfm , ESP - 20 mm.

od340405/2022_2023 : Circular type inline fan for ducted exhaust air application consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 700 cfm , ESP - 30 mm

od340406/2022_2023 : &nbsp;Circular type inline fan for ducted exhaust air application consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 900 cfm , ESP - 20 mm&lt;br&gt;

od340407/2022_2023 : Circular type inline fan for ducted exhaust air application consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1200 cfm , TSP - 20 mm

od341638/2022_2023 : Inline type fan suitable for ducted exhaust air application for OT fumigation consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1400 cfm , TSP - 20 mm.

od341639/2022_2023 : Inline type fan suitable suitable for ducted exhaust air consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 2200 cfm , TSP - 20 mm

od341640/2022_2023 : Ceiling suspended Fresh fan for the STP consisting of double skin casing (25 mm) , DIDW fan, drive motor , drive package, EFF-1 Motor, Pulleys, Belts &amp; Belt guard, drive sets, Flexible connection, base frame, spring mounts, For all other necessary information please refer the schedule for further details. Fan motor shall have necessary rating to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 2000 cfm , TSP - 40 mm- for STP ventilation.

od341641/2022_2023 : Floor mounted exhaust air fan consisting of double skin casing (25 mm) , DIDW fan, carbon filter, drive motor , drive package, EFF-1 Motor, Pulleys, Belts &amp; Belt guard, drive sets, Flexible connection, base frame, spring mounts, bird mesh etc. The fans are located on the above terrace floor. For all other necessary information please refer the schedule for further details. Fan motor shall have necessary rating to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 3000 cfm , TSP - 80 mm - for STP.

od341642/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 1200 CFM

od341643/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 900 CFM

od341644/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 800 CFM

od341645/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 600 CFM

od341646/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 500 CFM

od341647/2022_2023 :Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 400 CFM

od341648/2022_2023 :Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 200 CFM

od341649/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 100 CFM

od341650/2022_2023 : RECTANGULAR INLINE FAN - FRESH AIR FAN :-Double skin type Ceiling suspended units complete with double skin (25±2 mm) insulated with CFC free polyurethane foam (PUF) panels of 42 Kg/cum density. Sandwitched between 0.6 mm thick G.I. Sheets. Outer skin shall be preplastized G.I. sheet and internal skin shall be powder coated G.I. sheet. The unit shall be provided with forward curved blower, Motor, inlet filter section with MERV-8 filters, drive set &amp; guard, spring isolator to avoid transmission of vibration,etc. The motor shall be with IP54 protection, class F insulation. 900 CFM / 20mm Static

od341651/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 500 cfm , TSP - 20 mm

od341652/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 2200 cfm , TSP - 20 mm

od341655/2022_2023 : Double Skin cabinet type fan for ducted exhaust air application consisting of 25mm thick cabinet, HEPA filter, back ward curved impeller, flanged inlet and outlet connection, low noise level, thermally protected motor which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 400 cfm , ESP - 50 mm.

LOW VALUE ITEMS od343402/2022_2023 : Expansion Kit suitable for CSU/AHU with control panel

od343403/2022_2023 : S.I.T.C of SS grade plenum of suitable size for the equipments consisting of mini pleat HEPA filter, collar, volume control damper and access to filter. The arrangement should be suitable to mount above the OT Table. The unit shall be provided with a perforated Aluminum sheet at the bottom for air discharge.

od343404/2022_2023 : TERMINAL HEPA FILTERS :- Supply, Installation, Testing &amp; Commissioning of laminar station and SS plenum as follow: Laminar flow diffuser essentially should consists in: A plenum, constituting the pressurization chamber, entirely constructed of 1mm-thick 304 stainless steel sheet, with smooth finish to prevent dust collection. Four/Six square flanges are mounted to connect the plenum to air distribution ducts. External stiffening ribs and anticondensation insulation. Supply air filter housing, 304 stainless steel frame with stainless steel fasteners. Filtering unit consisting of absolute filters with efficiency &gt; 99,995%. Classification: CEN EN 1822 - H14. Sealed, stainless steel central component for connection of the surgical lamp. Lower component should consists of 1mm-thick 304 stainless steel panels with conveniently sized slots to assure the requested flow. The special system allows the perforated panels to be locked in and fully opened for easy and safe servicing and replacing of filters. Stainless steel mounting frame, constructed so as to assure sealed connection to the suspended ceiling, and perfect separation from the controlled work area by means of synthetic rubber seals. Diffuser Size: 2400x1800MM

od343405/2022_2023 : Communication cable between indoor and outdoor units of 2Cx1.5 Sqmm Cu. Cable placed in a 3/4"; conduit.

od343406/2022_2023 : Control cable of OEM recommended size between indoor and outdoor units of Dx type with necessary fixing arrangement.

od345161/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 1) 1/4 &quot; dia (6.4 MM) with 13 mm insulation

od345162/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. ) 3/8 &quot; dia (9.5 MM) with 13 mm insulation

od345163/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 1/2 " dia (12.7 MM) with 13 mm insulation

od345164/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 5/8" dia (15.9 MM ) with 13 mm insulation

od363931/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 3/4 " dia (19.1 MM ) with 13 mm insulation.

od345155/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 7/8" dia (22.4 MM) with 19 mm insulation.

od345156/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 1" dia (25.8 MM) with 19 mm insulation

od345157/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 1-1/4 "dia (28.6 MM) with 19 mm insulation

od345158/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 1-3/8 " dia (34.9 MM) with 19 mm insulation

od345159/2022_2023 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.) 1-5/8 " dia (41.3 MM) with 19 mm insulation

od345160/2022_2023 : Refnet joints of all required size of copper pipes as per manufacturer recommendation.

SUB HEAD 'C' DUCTING and GRILLS 16.12.1.1 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006- 0.63 mm thick

16.12.1.2 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006-0.8 mm thick

16.12.1.3 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006-1 mm thick

16.12.1.4 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006-1.25 mm thick

16.12.2.1 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

16.12.2.2 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.8. mm thick

16.12.2.3 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.00 mm thick

16.12.2.4 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.25 mm thick

od356163/2022_2023 : &nbsp;Supply, installation, balancing and commissioning of factory fabricated Aluminium sheet metal rectangular/round ducting for OT's complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of Thickness 0.64(22G) mm sheet

od356164/2022_2023 : Factory fabricated double skin plenum of 25mm thick PUF panels of density 40 kg/cum, casing inside &amp; outside material - GI casing inside &amp; outside thickness - 0.6 mm . The area indicated is the surface area of the plenum.

16.13 : Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

od366682/2022_2023 : Supply, installation, testing and commissioning of GSS Non return damper with frame and Blades neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

16.20.2 : Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Actuator

16.21.1 : Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm Gl section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. 16 <br> <br>Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3

od363809/2022_2023 : Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.

od363810/2022_2023 : Supplying and fixing of following thickness closed cell Nitrile rubber (class &ldquo;O&rdquo;) insulation on duct after applying two coats of cold setting adhesive (CPRX compound). The all joints shall sealed cotton tape insulation complete as per specifications and 10 mm thk.

od363811/2022_2023 : Supplying and fixing of following thickness closed cell Nitrile rubber (class O;) insulation on duct after applying two coats of cold setting adhesive (CPRX compound). The joints shall sealed cotton tape insulation complete as per specifications and 13 mm thk.

od363812/2022_2023 : Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class O) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.19 mmsqm

od363813/2022_2023 : Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/cum after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape covering with 0.63mmx19mm GI wire mesh netting &amp; butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications)

16.14.1 : Supply, Installation, testing and commissioning of motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU roomMotorized (ON-OFF Type) duct mounted GI volume control damper

16.15 : Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

od356154/2022_2023 : Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

od356155/2022_2023 : Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 250 mm dia

od356156/2022_2023 : Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 200 mm dia

od356157/2022_2023 : Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 150 mm dia

od356158/2022_2023 : Supply, installation, testing & commissioning of Butter fly dampers of GI construction made out of 22G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 250 mm dia

16.19.1 : Supplying, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regulator interval as per site requirement etc. complete as required as per specifications.Thermal insulated flexible duct (200 mm dia)

od345179/2022_2023 : Supply, installation, testing & commissioning of Butter fly dampers of GI construction made out of 22G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 150 mm dia

od345180/2022_2023 : Return air cross talk attenuators -Factory fabricated Z type made of 24G GI sheets of 300mm wide x 300mm height of 1.5m length with accoustic lining of 15mm thick open cell nitrile rubber insulation of class-1 accoustic 140-180 Kg / M3 density stuck to the clean internal surface of the duct with good quality low VOC content adhesive. Suitable size grille at the outlet to be considered accordingly.complete as required as per specifications. Type-01

od345181/2022_2023 : Return air cross talk attenuators -Factory fabricated Z type made of 24G GI sheets of 400mm wide x 500mm height of 1.5m length with accoustic lining of 15mm thick open cell nitrile rubber insulation of class-1 accoustic 140-180 Kg / M3 density stuck to the clean internal surface of the duct with good quality low VOC content adhesive. Suitable size grille at the outlet to be considered accordingly.complete as required as per specifications.Type-02

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

16.18 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

od345167/2022_2023 : Supplying, fixing testing commissioning of Exhaust Disc Valve for the each disc valve

od345168/2022_2023 : Non Vision grills for the toilet doors. The grills shall be supplied in two matching halves and shall match the door thickness. The grills shall be powder coated .

od345169/2022_2023 : Supplying, fixing, testing &amp; commissioning of powder coated extruded aluminium section fresh air grill in weather maker room with aluminium volume control dampers, bird screen etc complete as required

od345170/2022_2023 : CONDENSATE DRAIN PIPING : Supply, inatallation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 20mm dia

od345171/2022_2023 : Supply,installation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 25mm dia

od345172/2022_2023 : Supply,installation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 40mm dia

od345173/2022_2023 : Underdeck insulation with 50mm thick TF quality Expanded polystyrene fixed to the slab with Rawl plugs and GI washers and tied with GI wire.

od345174/2022_2023 : SITC of Al.powder coated 6"; continuous grill with end flanges

od345175/2022_2023 : SITC of Al.powder coated 4"; continuous grill with end flanges

od345176/2022_2023 : SITC of Opposed blade collar dampers of powder coated Aluminium.

od356145/2022_2023 : SITC of outdoor wheather proof Polycarbonate box of IP level 67 with 415V 4P 32/40/63 Ampere 100mA ELCB including all fixing mountings.

od356146/2022_2023 : &quot;SITC of Automatic timer control with Power connection for switching the Fan/AC etc. Consisting of the following&lt;br&gt;1. 2 Nos. 63A, 415V, AC-4 duty 3P contactor-2 set&lt;br&gt;2. Timer-1 No.&lt;br&gt;3. Auxilliary switches and Push button, actuation etc.-1 set&lt;br&gt;4. Enclosure fabricated with 16SWG CRCA sheet

FIRE PROTECTION SYSTEM

UNDERGROUND PIPING (Including Wrapping and Coating) od390843/2022_2023 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required, Including Excavation, back filling, wrapping and Coating.200 mm dia.

od390854/2022_2023 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required,Including Excavation, back filling, wrapping and Coating. 150 mm dia.

od390867/2022_2023 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between &amp; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required,Including Excavation, back filling, wrapping and Coating.100 mm dia

od390871/2022_2023 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between &amp; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required,Including Excavation, back filling, wrapping and Coating. 80 mm dia

PIPING ABOVE GROUND od390856/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between &amp; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.200 mm dia

od390866/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.150 mm dia

od390872/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.100 mm dia

od390880/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.80 mm dia.

od390888/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.40 mm dia.

od390896/2022_2023 : Supply, fixing, testing and commissioning of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Project Manager's / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head.25 mm dia.

od390902/2022_2023 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC).150 mm dia.

od390908/2022_2023 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC).100mm dia

od390913/2022_2023 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC).80mm dia

od390915/2022_2023 : Supply, installation, testing &amp; commissioning of sight galss unit of dia 25mm for test connection with all necessary fittings and accessories etc.,complete

od390919/2022_2023 : Supply, installation, testing &amp; commissioning of 150mm dia pressure gauge ( Glyserine Filled), siphon and cock burden type suitable for required pressure dial to be graduated both on PSI and Kg/Cm2 with all necessary jointing materials and fittings etc., complete

od390921/2022_2023 : Providing & fixing of pressure switch in pipe line including connection etc. as required

od390926/2022_2023 : Providing & fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 100mm diameter

od390927/2022_2023 : Providing & fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 150mm diameter

od390930/2022_2023 : Providing, installation, testing & commissioning of adjustable rosette plate for 15mm diameter, fabricated by M.S. plate of 2mm thick and the finish shall be powder coated in white finish UL Listed or FM approved complete as required

od390934/2022_2023 : Providing, Laying. Testing & Commissioning of 450 mm dia RCC pipes of NP2 class with suitable collars filling the recess at joints of pipes with hemp dipped in hot bitumen or other suitable compound for chaulking of joint by jack, setting up of loose space over the collar joints chaulked with CM 1:2, finished both ends to a slope of 1:1 including curing, testing of pipes, etc., Complete all as specified and directed by Engineer in charge. Note: Earth work will be measured under relevent Items

od390936/2022_2023 : Supply, fixing, testing and commissioning of Test connection with 25mm dia GM ball valve Complete all as specified and directed by Engineer in charge.

Valves and Fittings od390844/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge. 200 mm dia

od390853/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge.150 mm dia.

od390863/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge.100 mm dia

od390875/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge.80 mm dia

od390884/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge.65 mm dia

od390889/2022_2023 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge.50 mm dia

od390898/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return / Air Cussion valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete, GI bolts, nuts, washers etc.as required. 200 mm nominal diameter

od390901/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete, GI bolts, nuts, washers etc.as required. 150 mm nominal diameter

od390906/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete, GI bolts, nuts, washers etc.as required. 100 mm nominal diameter

od390911/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete, GI bolts, nuts, washers etc.as required. 80 mm nominal diameter

od390917/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete, GI bolts, nuts, washers etc.as required. 50 mm nominal diameter

od390920/2022_2023 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size 150 mm nominal diameter

od390922/2022_2023 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size 50 mm nominal diameter

od390924/2022_2023 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type.25 mm diameter

od390928/2022_2023 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type.50 mm diameter

od390929/2022_2023 : Providing & fixing heavy forged brass tested ISI marked 2280 Lpm Flow Pressure Relief valves (16 Bar) of approved quality with all necessary Piping connections till the Bypass valve to Water Tank (To be installed in diesel pump Header in Pump Room)

od390933/2022_2023 : supply installation of UL listed pressure gauge 1/4" BSPT, minimum 3.5" dial of suitable range to be installed in pump room suction, discharge, diesel pump and Sprinkler & Standpipe Systems. Dial type White background black graduation scale with dual reading in Kg./ Sq.cm and PSI complete as required.

od390937/2022_2023 : Supply, fixing, testing and commissioning of Providing, fixing, testing & commissioning of Zone control valve of cast iron body,brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required.

od390938/2022_2023 : Supply, fixing, testing and commissioning of the SINGLE HEADED YARD HYDRANT (EXTERNAL) of first quality, approved brand, confirming to relavent IS composed of the following :-a) 80 mm dia GIF bend. b) 80 mm dia GIF stand pipe (1 Mtr above). c) 63 mm dia female instantenous pattern oblique hydrant valve chain and cap of Gun metal. The pipe portion below ground shall be painted with 3mm thick bituminous coat and pipe exposed outside shall be painted with 2 coats of synthetic enamel paint over a coat of primer. etc Complete all as specified and directed by Engineer incharge.

od390941/2022_2023 : Supply, fixing, testing and commissioning of the SINGLE HEADED YARD HYDRANT( INTERNAL ) with inbuilt PRV of first quality, approved brand, confirming to relavent IS composed of the following :-a) 80 mm dia GIF bend. b) 80 mm dia GIF stand pipe (1 Mtr above). c) 63 mm dia female instantenous pattern oblique hydrant valve chain and cap of Gun metal. The pipe shall be painted with 2 coats of synthetic enamel paint over a coat of primer. etc Complete all as specified and directed by Engineer incharge.

od390944/2022_2023 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 150mm dia.

od390945/2022_2023 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 200mm dia.

od390948/2022_2023 : Supply and fix external glass fronted hose cabinet glass fronted with hinged and lock, made out of 16 G M.S. sheet of suitable size with (3mm thick glass with rubber beeding) door and size of the cabinet shall be 750 mm x 600 mm x 250 mm powder coated paint complete all as specified and directed by Engineer incharge. With a) 2 lengths of 15 M long, 63mm dia RRL hose with instataneuos couplings and Hoses shall be stored in side the hose cabinet.b) Branch pipe &amp; nozzle (one set). c) Two keys of Recess type for break glass.

od390949/2022_2023 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished. Pendent sprinkler

od390950/2022_2023 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished. Upright

od390951/2022_2023 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished. Side wall

od390952/2022_2023 : Supply, installation, testing & commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings & accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1 m length

od390953/2022_2023 : Supply, installation, testing & commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings & accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required 1.2 m length

od390954/2022_2023 : Supply, installation, testing &amp; commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings & accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required 1.5 m length

od390864/2022_2023 : Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

od390869/2022_2023 : Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required. <br>

od390882/2022_2023 : Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. (above false ceiling)

od390890/2022_2023 : Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with ounting base complete as required. (below false ceiling) <br>

od390899/2022_2023 : Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

od390905/2022_2023 : Supplying, installation, testing &amp; commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

od390909/2022_2023 : Analogue Addressable Monitor module for monitoring the field devices &amp; shall be capable of providing DPDTcontact rated at 24v DC, 2A. ( for flow switches)

od390912/2022_2023 : Analogue Addressable Control relay module for AHU tripping and shall be capable of providing DPDTcontact rated at 24v DC, 2A.

od390916/2022_2023 : Supplying and fixing of PC Pentium IV ,with 933 MHZ, 512 MB RAM,20 GB, HD, 17" monitor, 132 column colour dot matrix printer shall also be supplied.

od390918/2022_2023 : Supplying, installation, testing & commissioning of addressable manual call point with break glass type complete as required.

od390923/2022_2023 : Supplying and fixing 25 mm dia MS flexible pipe with PVC (conduit) coating along with all ancillaries and accessories like coupler etc. as required. 25 mm dia. (for laying cables on stairs wall)

od390925/2022_2023 : Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

od390931/2022_2023 : Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

od390932/2022_2023 : Supplying, installation, testing & commissioning of fault isolator module complete with base as required.

od390935/2022_2023 : Supplying, installation, testing & commissioning of addressable fire control module complete as required.

od390939/2022_2023 : Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

od390940/2022_2023 : Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

TWOWAY TALK BACK (P.A.) SYSTEMS od390849/2022_2023 : Supply and fixing of Talk back speaker unit 5W LMT, Press to talk switch MS housing with Red color.

od390858/2022_2023 : Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Panel should be with CRCA sheet housing, control desk( rack) and suitable rack for mounting amplifier & console as required. Console shall have all call / call back facility complete with battery back up and it should also work on AC single phase power. PA console, amplifier and all associate accessories shall be installed in metal sheet fabricated cabinet.

od390862/2022_2023 : Supplying, installation, testing & commissioning of Voice command keypad 6 zone, (two way talk back system for staircases) with microphone assembly complete as required.

od390877/2022_2023 : Supplying, installing, testing and commissioning solid state Amplifier of 480 W RMS out put in rack, including necessory control wires, jocks etc. complete.

od390886/2022_2023 : Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

od390900/2022_2023 : Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

FIRE EXTINGUISHERS SHALL BE PROVIDED AS PER NBC-IS 15683 od390846/2022_2023 : Supply and install in position approved make Dry Chemical Powder Fire Extinguisher 5/6 Kgs capacity (ABC Type) complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial charge of Dry Chemical Powder and gas cartridge complete with bracket and fixing screws. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder bearing No. IS:15683 and the gas cartridge bearing with ISI certitifcation mark. Complete all as specified and directed by Engineer in charge.

od390852/2022_2023 : Supply and install in position approved make carbon-di-oxide 4.5 Kgs capacity fire extinguisher, made of high pressure with wheel type valve with one metre long braided high pressure discharge hose which should have a minimum of bursting pressure of 14.0 N/Sqmm and fitted with ABS discharge born and handles (non-conductor), complete with bracket and steel handle on the body fully charged with ISI certification. mark, ISI:2878/1976. Complete all as specified and directed by Engineer in charge.

od390861/2022_2023 : Supply installation of 2 Nos.Fire buckets filled with sand round bottom type enamel painted, white inside & Red out side and Letter "FIRE" in black out side and handle with mounting bracket as per the tender drawing. Along with Fabrication supply and installation of Fire bucket stand fabricated by MS angles/pipes to install 2 Nos. of buckets. Complete all as specified and directed by Engineer in charge.

od390874/2022_2023 : Supply and install in position approvedmake AFFF Mechanical Foam Fire Extinguisher, 9 Ltrs capacity fitted with chromium plated gun metal cap, plastic coated gas cartridge fitted with braided hose and foam branch complete with brackets and initial charge of Aqueous film forming liquid of 6% concentration as per IS:10204.

od390878/2022_2023 : Supply and install in position approvedmake AFFF Mechanical Foam Fire Extinguisher, 50 Ltrs capacity fitted with chromium plated gun metal cap, plastic coated gas cartridge fitted with braided hose and foam branch complete with brackets and initial charge of Aqueous film forming liquid of 6% concentration as per IS:10204.

od390891/2022_2023 : Supply and install in position approved make Dry Chemical Powder Fire Extinguisher 10 Kgs capacity (ABC Type) complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial charge of Dry Chemical Powder and gas cartridge complete with bracket and fixing screws. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder bearing No. IS:15683 and the gas cartridge bearing with ISI certitifcation mark. Complete all as specified and directed by Engineer in charge.

od390897/2022_2023 : Supply and install in position approved make Water Co2 Fire Extinguisher of 9 Ltrs capacity of conical shape fitted with chromium plated gun metal nozzle on the top end of the fire extinguisher for discharge of liquid and chromium plated gun metal union (Cap) at the bottom with angle fixed in the centre, complete with bracket, fixing screws, spanner and one filling. The extinguisher is internally and externally coated with lead, tin alloy through hot-dip process and bearing IS:15683 with ISI certification mark. Complete all as specified and directed by Engineer in charge.

FIRE SIGNAGES od390847/2022_2023 : Fire Exit signage Dual Side above the door of each stair enclosure on every floor, indicating the direction of exit in case of fire emergency, lettering size shall be 5 cm with contrasting colour from back ground.Size shall be 6" x 12". Complete all as specified and directed by Engineer in charge.

od390865/2022_2023 : Providing and installing in position the following type of sign board made out of 3mm thick "opaque" PVC foam board with computer cut, design, letters letters on both side with instructed letter dimensions and colour etc., PVC non-reflective vinyl painted foam board, complete with hanging chain/wall hangings, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height.'15cmX50cm

od390873/2022_2023 : Providing and installing in position the following type of sign board made out of 3mm thick "opaque" PVC foam board with computer cut, design, letters on both side with instructed letter dimensions and colour etc., PVC reflective vinyl painted foam board, complete with hanging chain, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height.'15cmX50cm

od390879/2022_2023 : Providing and installing in position the following type of sign board made out of 3mm thick "opaque" PVC foam board with computer cut, design, letters on both side with instructed letter dimensions and colour etc., PVC reflective vinyl painted foam board, complete with hanging chain, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height.'2' x 3'

od390892/2022_2023 : Fire Exit signage Single Side above the door of each stair enclosure on every floor, indicating the direction of exit in case of fire emergency, lettering size shall be 5 cm with contrasting colour from back ground.Size shall be 6" x 12". Complete all as specified and directed by Engineer in charge.

FIRE PUMP ROOM EQUIPMENT od390870/2022_2023 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.<br>

od390883/2022_2023 : Supply and laying of 8 SWG copper wire through ceiling / walls, from the equipment to the nearest Earth pit/Earth bus with necessary accessories as required. (Earth pit shall be executed by other agencies).<br>

od71433/2023_2024 : Supplying, erecting, testing and commissioning FIRE HYDRANT PUMPS DRIVEN BY ELECTRIC MOTOR as per the following: : a) Centrifugal fire hydrant pump of 2280 LPM, @ 56 M Head (8.8 Kg/Cm2) pressure capacity along with horizontal split cast iron casing type, bronze impeller, SS 410 Shaft, mechanical seal foundation bolts / Anti vibration pads, and accessories as specified and directed. b) Electric TEFC Motor of suitable HP, 2900 rpm, 415 V, 3phase, 50 Hz AC, DOL starter including a terminal box for cable entry, size gland and termination, common bed plate and foundation bolts etc complete all as specified and directed. <br>

od71434/2023_2024 : Supplying, erecting, testing and commissioning FIRE HYDRANT PUMPS DRIVEN BY DIESEL ENGINE as per the following: : a) Centrifugal fire hydrant pump of 2280 LPM, @ 56 M Head (8.8 Kg/Cm2) pressure capacity along with horizontal split cast iron casing type, bronze impeller, SS 410 Shaft, mechanical seal all as per specified and directed. b) Suitable HP, 1500 RPM automatic diesel engine driven pumpset ,DOL starter, along with residential silencer system,exhaust pipe with insulation & cladding, exhaust pipe upto outside of building, fuel tank, necessary cooling system, with OS & Y valve, NRV, Y stainer foundation bolts / Anti vibration pads, Pressure Guage, Pressure switch, test valve, day oil storage tank, two separate starting mechanism (automatic starting by battery power electric starting motor as well as manual starting motor all as per the specified and directed. <br>

od71435/2023_2024 : Supply, erection, testing and commissioning of vertical inline 180 LPM, @ 56 M Head (8.8 Kg/Cm2) pressure capacity Centrifugal Jockey pump coupled with suitable eletrical driven motor, necessary foundtion bolts,and accessories, connections etc. Complete all as specified and directed by Engineer incharge. <br>

od71436/2023_2024 : Supplying, installing, testing and commissioning of double flanged Rubber Expansion Bellows/ joint of standard length as per manufacturers specs including rubber PTFE / Asbestos free gaskets, flanges, nuts, bolts and washers complete as required. (Suction and Discharge side PN16) 150mm nominal diameter

od390893/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 12 C x 2.5 Sqmm. copper Diesel engines <br>

od390894/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 4 C x 16 Sqmm. Aluminum Jockey pump<br>

od390904/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 3.5C x 120 sq.mm aluminum for main pumps <br>

od390910/2022_2023 : Providing and fixing of exhaust pipe M.S. Medium grade for Diesel engine shall not be smaller in diameter than engine exhaust outlet extended outside pump house, duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, flexible exhaust connection, residential silencer, instruments and protection as per specification NFPA 20 ,2016 with stand & gauge glass, painting, rain cap and necessary supports as required.<br>

od390914/2022_2023 : Supplying, installing, testing and commissioning of double flanged Rubber Expansion Bellows/ joint of standard length as per manufacturers specs including rubber PTFE / Asbestos free gaskets, flanges, nuts, bolts and washers complete as required. (Suction and Discharge side PN16) 150mm nominal diameter

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.3 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.225 mm width X 50 mm depth X 1.6 mm thickness

MANIFOLD AND PLANT ROOM - OXYGEN SYSTEM od75719/2023_2024 : Supply, installation testing and commissioning of Automatic Oxygen Control Panel with minimum flow rate of 1600 LPM with liquid oxygen connectivity, suitable for 2x10 manifold system Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specifications. The cylinders shall not be included in the quoted price.

od75740/2023_2024 : Supply,testing and commissioning of valves and high flow regulators for Oxygen Manifold system as per technical specifications.

od75747/2023_2024 : Supply,testing and commissioning of Cylinder Emergency Oxygen&lt;br&gt;Manifold with high flow regulator- 1 Bank X5 Cylinders

od75753/2023_2024 : Supply,testing and commissioning of Oxygen Manifold - 2 banks x10 cylinders, as per technical specifications. The cylinders shall not be included in the quoted price.

Nitrous oxide system od75728/2023_2024 : NITROUS OXIDE SYSTEM: Supply,testing and commissioning of automatic N2O control panel complete set with inlet and outlet connectors suitable for 2x2 manifold system with minimum flow rate of 600 LPM, fully automatic control panel for both sides with brass hosing and suitable connectors. &frac12;&rdquo; BSP (M) thread.

od75733/2023_2024 : Supply,testing and commissioning of Cylinder Emergency Nitrous oxide Manifold with nesessary regulating system - 1 bank x 2 cylinders as per technical specifications.

od75741/2023_2024 : Supply,testing and commissioning of Nitrous Oxide Manifold - 2 banks x 2 cylinders.as per technical specifications. The cylinders shall not be included in the quoted price.

CARBON DIOXIDE SYSTEM od75721/2023_2024 : Supply,testing and commissioning of Cylinder CO2 Manifold - 1 bank x 2 cylinder with a high flow regulator with gauges and safety valves complete with all accessories etc. as required complete as per specification

od75736/2023_2024 : CARBON DIOXIDE SYSTEM: Supply,testing and commissioning of semi automatic CO2 control panel complete set with inlet and outlet connectors for automatic for both sides with brass housing and suitable connectors. &frac12;&rdquo; BSP (M) thread.

MEDICAL AIR SYSTEM od75722/2023_2024 : MEDICAL AIR SYSTEM: Supply,testing and commissioning of Compressed air plant complete with - 2 compressors, each compressor should have minimum free air delivery of 1600 LPM @10bars, 1 air receiver tank of minimum 1500 ltr capacity, filtration and dryer system to ensure medical air quality as per HTM standards (each compressor module should include an inline filter with particle retention of 10 microns), NRV, pressure reducing station,automatic drain valves,pressure guages,ball valves, electrical control panel including circuit breakers, starters, pressure switches, timers, as per technical specifications

od75738/2023_2024 : VACUUM PLANT: Supply,testing and commissioning of Vacuum plant complete with 1 vacuum pump and one as standby, each vacuum pump should have minimum free air aspirated of 2000 LPM betwen 570 mmHg and 720 mm Hg.min, vaccum receiver tank of minimum 1500 ltr capacity,bacteria double filter, valves,pressure guages,NRV, electrical control panel including circuit breakers, pressure switches, timers, ball valves etc as per technical specifications.

Motor control od75723/2023_2024 : Supply, Installation , testing and commissioning of motor control center consisting of 125 Amp 4P isolator incomer, phase indicators ,outgoing of 5 nos 63 TP D curve MCB ,starters, push button, motor protection devices, instrumentation, control cabling for Air compressor &amp; vaccum Pump system etc as per technical specification

PIPE LINE SYSTEM od75724/2023_2024 : Supply,installation testing and commissioning of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards.All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.42 mm x 1.2 mm thick Copper pipe

od75735/2023_2024 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards .All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specification -12mm x 1 mm thick copper pipe

od75742/2023_2024 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.54 mm x 1.2 mm thick Copper pipe

od75751/2023_2024 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.28 mm x 0.9 mm thick Copper pipe

od75756/2023_2024 : Supply,installation testing and commissioning of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards.All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specifications. 22 mm x 0.9 mm thick Copper pipe

od75761/2023_2024 : &lt;br&gt;Supply of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specification15 mm x 0.9 mm thick copper pipe

GAS OUTLETS od75727/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Venturi type AGSS outlets conforming to EN ISO 9170-2

od75732/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. CO2 Outlets with Probes

od75743/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Vac Outlets with Probes

od75750/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Air (7 bar) Outlets with Probes

od75755/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications-Air (4 bar) Outlets with Probes

od75757/2023_2024 : Supply, Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. N2O Outlets with Probes

od75760/2023_2024 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications.O2 Outlets with Probes

Master Alarm panel od75720/2023_2024 : Supply,testing and commissioning of Master Plant Alarm Panel ,Complies with HTM 02-01/ISO-7396-1 Standards. Each Master Alarm should be modular in design and be fitted with required number of master alarm modules. The master alarms should be capable to monitor minimum 25 point. Each point represents an alarm condition that the source equipment might have. When an alarm condition exists, a red-light flashes and the audible alarm sounds. If several alarm conditions occur simultaneously, the most recent alarm light should flash, while the other alarm lights should remain lit. When an alarm condition is created, an audible alarm should be actuated. A dry contact module should be available to interface with a building management system. The box material should be of gauge steel of requisite thickness and equipped with mounting brackets. The emissions from alarms should conform with EMC standards. Master alarm management system should be designed to display alarm conditions from the source supply units indicating the broad status of the source equipment and manifolds as well as the master distribution status from the source supplies. Depending on the alarm priority, a visual and audible alarm should be initiated to indicate an alarm condition. Each panel shall display and/or input of multi point alarms,including all necessary cabling between mater alarm and floor panels. The master alarm must be able to monitor the following source alarm conditions. as per technical specifications.Master Plant Alarm Panel ,Complies with HTM 02-01/ISO

Area valve +alarm unit od75729/2023_2024 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 7 gas- 2 O2,IM air,1 N2O, 1 CO2, 1 s air, 1 vac

od75730/2023_2024 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 5 gas - 2 O2, 1M air, 2 Vac

od75744/2023_2024 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 3 gas - 1 O2, 1M air, 1 Vac

od75752/2023_2024 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 2 gas - 1 O2, 1 Vac-

BALL VALVES od75739/2023_2024 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-42mm

od75748/2023_2024 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications 54 mm

od75754/2023_2024 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications28mm

od75758/2023_2024 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications

od75759/2023_2024 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-15 mm

OXYGEN GAS CYLINDER od75718/2023_2024 : Supply,testing and commissioning of D type CO2 Gas filled Cylinder having as per technical specification.D type CO2 Gas filled Cylinder

od75737/2023_2024 : Supply,testing and commissioning of D type Nitrous Oxide Gas filled Cylinder as per technical specification.D type Nitrous Oxide Gas filled Cylinder

od75745/2023_2024 : Supply, testing and commissioning of class D type Oxygen Gas filled Cylinder etc in complete as per technical specification.

BED HEAD PANELS od75726/2023_2024 : Supply and installation of Bed Head 5ft(Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch &mdash; 1, spare probe, 2 no 5 /15A combined socket with switch outlet &mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge.-Bed head panel as above with 5 Gas outlet

od75731/2023_2024 : Supply and installation of Bed Head 5ft(Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch &mdash; 1, spare probe, 2 no 5 /15A combined socket with switch outlet &mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge. Bed head panel as above with 3 Gas outlet

BPC od75725/2023_2024 : Supply, Installation, testing and commissioning of High Pressure Antistatic Hose with color coded.

od75734/2023_2024 : Supply Installation of Theatre Vacuum unit with trolly and 2000 ml collection jar as per technical.

od75746/2023_2024 : Supply Installation of Ward vacuum unit with 600 ml collection jar asper technical specification.

od75749/2023_2024 : Supply Installation of BPC Oxygen Flow meter as per technical specification.

od77065/2023_2024 : Supply, installation, testing &amp; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman&rsquo;s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding,, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Less Type with the traction motor placed on top of the hoistway and elevator shall be of gearless type (suitable for lift well size 3000mm (D)X 2400m(W)) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1200mm wide X 2000mm height. 20 passengers (Minimum) capacity (minimum 1360 Kgs) Bed Lift , car size of 1300mm wide x2400mm deep x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, stretcher protection on three sides complete as per specifications. Hospital Block 7 stops &amp;7 openings ,Total travel height is approximately 28 M

Dump waiter od77068/2023_2024 : SITC of Dump waiter of 100 kg capacity suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, speed of 0.30 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with buttons, reverse phase relay on controller, digital car positions indicator on wall at all floors with Up/DOWN direction, all signal fixtures in stainless steel faceplates, light fixtures, etc complete with all accessories. The equipment traction motor placed in the Machine Room, geared type with travel height of 30.mtrs. (suitable for well size 1200mm (W)X 1200m(D) simplex operation. Equipment entrance protected by SS doors with min 700mm x 700mm opening size. Complete with necessary scaffolding, logic control panel and shaft lighting etc required for the erection of the dump waiters. Capacity Minimum 100 Kgs, 7stops &amp; 7openings with min car size of 700mm wide x600mm deep x 800mm height Inside dimensions and entrance at front side on all the serving floors, provided with SS car on other three sides, SS finish ceiling Aluminum chequred plate flooring complete as per specifications.

CASUALITY BLOCK od77181/2023_2024 : Supply, installation, testing &amp; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman&rsquo;s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding,, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Less Type with the traction motor placed on top of the hoistway and elevator shall be of gearless type (suitable for lift well size 3000mm (D)X 2400m(W)) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1200mm wide X 2000mm height. 20 passengers (Minimum) capacity (minimum 1360 Kgs) Bed Lift , car size of 1300mm wide x2400mm deep x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, stretcher protection on three sides complete as per specifications. 3 stops &amp; 3 openings ,Total travel height is approximately 14 M

SOLAR PV PANELS

od122541/2022_2023 : Supply Installation Testing and Commissioning of grid connected solar system with 50kWp monocrystalline solar PV panels5 0kW grid connected string inverter having all protective devices, AC &amp; DC distribution board with MCB&apos;s and surge protective devices, AC distribution board having 1 no 125A isolator &amp; 2/3 no&apos;s 63A MCB&apos;s, 3 Phase 4 wire -/5A,Cl 0.2s energy meter including CT&apos;s ,Supply and fixing HT CT net meter necessary cabling including DC cable for panel to inverter / DC DB and AC cabling from inverter to AC DB , AC panel and Main panel ,all civil and mechanical works for supporting, earthing using proper cable /strip, 4 nos earth electrode ,earth leads,and lightning protection system as directed by electrical inspectorate, preparation of design and getting approval from Electrical inspectorate /KSEBL and getting energization sanction, all the works shall comply the MNRE standards.

od76404/2023_2024 : Providing and fixing steel structure for supporting solar PV panel up to a height of 3 meter from floor level including fixing of tubular poles ,purling ,anchor faster for complete installation of item above