Repairs and maintenance of civil works to certain buildings and periodical services to certain buildings and boundary wall at Mily Station Calicut under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

All as per item No 4 but except scantling all as specified and directed. Note : Serviceable scantling obtained from item No 3 shall be reused.

Dismantling of asbestos cement (corrugated, semi corrugated, etc) sheets in roof covering including ridges all as directed.

Dismantling unframed timber scantling under 40 sqcm in section in any position unframed work all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new/old of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

M&L for structural work in tubular sections including special shaped washer, etc, complete using ERW or induction butt welded tubes etc Fe 410W (Gde E-250) quality B all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of stone slab and tiles of any description and thickness in floors including cement mortar bedding (but not backing), and rubbish off the premises outside MD land and all as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L for coloured non-skid ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles exc 0.09sqm but n exc 0.16sqm on plan as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 21 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

M&L for second class hardwood, panelled shutter 30mm thick (any number of panel) with lock rail and panel of 9mm BWP. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size fixed with stainless steel screws all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

Dismantling wall and ceiling boards or insulation boards/slabs/blankets any thickness, including cover fillets all as specified and directed.

M&L for Gl 600 x 600 mm snap grid frame, powder coated sections comprising of undermentioned sections etc for grid frame :- (a) Suspended GI main runner 38 X 24mm bulb Tee sections fixed with 4 mm dia GI bar @ 1200 mm c/c, level shall be adjusted with fly/bionet screws. (b) Placed in position cress Tee 1200 mm long and 28.8 X 24 mm bulb Tee section @ 605 mm c/c using snap and bionet fixing arrangement to secure main runnners (c ) Ceiling GI 28.8 X 24 mm size bulb section installed 605 mm long in between cross Tee. (d) GI coated angle 24X24 mm fixed with PVC Rawl plugs and GI screws to secure with walls and all as per manufacturers instructions complete all as specified and directed.

S&F 4 mm thick non asbestos fiber cement building boards of any texture inserted to GI grid as per manufacturers instructions as in ceilings flat or sloping complete all as specified and directed.

M&L for preparation of new non AC ceiling board surfaces and applying three of white wash all as specified and directed.

Demolition of brick or stone or PCC block masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

All as per item No 42 here in before but except laterite all as specified and directed. Note : Serviceable laterite stone obtained from item No 41 shall be reused.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls surfaces all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15 mm bore UPVC pipes (ASTM) of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC pipes (ASTM) of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F in repairs bib tap 15mm dia, chromium plated, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repairs 15mm pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F 500 litres capacity rotational moulded polthylene water storage tanks (cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks (cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F Vitreous China premium/1st quality Wash down water closet pan, white or ivory (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F in repairs Vitreous China valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density suitable size PVC flush pipe all as specified and directed.

Supply and fix PVC connection 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F mild steel chromium plated Health faucet (ABS body), suitable for 15mm dia pipe with flexible LDPE pipe with jet of 1.25m long on one end and socket joint of 15 mm dia on other end including ABS wall hook complete all as specified and directed.

S&F inrepairs Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

S&F in repairs stainless steel plate rack of 1mm thick (for kitchen), of overall size not less than 90cm x 90cm x 20cm of standard pattern/ design and weight not less than 6.50 Kg each all as specified and directed.

M & L preparing old treated surface of walls (plastered or unplastered) including cornices and pillasters and applying one coat of white wash on wall all as specified and directed (internally/externally).

M & L washing, rubbing down and stopping of previously distempered surfaces of walls and applying one coat of oil emulsion distemper (white or tinted) all as specified and directed.

All as per item No 66 here in before but on ceiling surfaces all as specified and directed.

M & L preparing old treated surface of walls (plastered or unplastered) including cornices and pillasters and applying one coat of cement based paint all as specified and directed.

M&L for preparing old painted wood/wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

All as per Sl item No 69 above, but on steel surfaces all as specified and directed.

M&L for preparation of new plastered surface of wall (plastered or unplastered) and applying two coats of cement based paint over a coat of primer all as specified and directed.

M&L for writing Stops, commas, short lines, dashes, hyphens, brackets etc all as specified and directed.

M&L for writing letters or figures ( Block, Roman, Italic or Indian) n. exc. 30cm long including necessary stops, commas, short lines, dashes, hyphens ,brackets, etc. with white enamel paint all as specified and directed.

M&L for preparation of old painted surface of labels (square, rectangular or triangular ) in any shape n. exc. 0.1 Sq.m each and applying one coat of synthetic enamel paint (with black paint) including cutting in edges all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scapping down and preparation of surfaces even and smooth and applying two coats of first quality acrylic smooth exterior paint @ 1.67 litre per 10 sqm over a coat of exterior primer @ 2.20kg per 10sqm over two coats of exterior water proof putty complete all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scapping down and applying 1.5mm thick of acrylic wall care putty for making the surface smooth and even and applying two coats of acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, alkali and fungal resistance , dirt resistance exterior paint of approved shade over a coat of exterior primer @ 0.90 litre per 10sqm all as specified and directed.

JEETH CONSTRUCTION

NKS INFRATECH

LAKSHMI BUILDERS