DAY TO DAY MAINT OF OFFRS/JCOS/ORS, OFFRS OTM AND MD ACCN UNDER ZONE B OF GE (A) AHMEDABAD

Amount

Notes : (i) The work consists of 01 job as under:- JOB (A) : MAINT GRANT 2025-2026 (ii) Please refer schedule 'A' notes before quoting the tender. (iii) Amount of Schedule of Credit shall be deducted off line by the department.

Note:(i) Contractor's supervisor will report on all working days along with carpeneter,plumber, mason,welder,Electricians etc 0830 hrs at Complaint Cell to receive complaint for plumbing,carpenter works,masonry works,welding and to submit completion report on the same day by 1700 hrs. (ii) Printed complaint slip area wise as per format approved by Engineer-in-Charge shall be provided and maintained by contractor. (iii) Rate quoted shall be deemed to incl the cost of Computer system,Cyber secured installation of App,T&P, equipment, saftey devices etc alongwith sufficient labour to full fill the requirement to the entire satisfaction of Engineer-in-charge. (iv) Cost of labour for providing new items including replacement /Demolition/ dismantling/ taking out/down of old unserviceable item shall be deemed under respective item. (v) Cost of material shall be measured and paid separately under relevant items .If complaint delayed more than 48 hrs, Rs1000/- recovery will be made for each complaint per day (viii) No seperate payment will be paid to any tradesmen and supervisor (ix) All below maint work sites will be handed over in piece meal/patches in any qty and size for execution of the work without damaging the undamaged portion as per user requirement. (x) For the emergency work like water tanks, plumbing fittings etc which effects basic needs, stores will be procured in advance by the contractor and fixed on emergancy basis on short notice

M&L for Attending complaints related to Plumbing/Water Supply and obtaining completion from user including minor repair of taps by replacement of washers, tightening of taps, spindals of any size , tightening of check nuts, PVC connection and making water supply functional in case of blockage redressing of GI pipe joints if any leakage is found, repair of un-functional PVC flushing cistern, repair/replacement of face mohra etc.

M&L for attending complaints related to Carpenter Work and obtaining completion from user including repair of easing of doors re-fixing or retightening of doors, windows, resecuring of door/window wire guage etc including nails, screws etc required to make good the work (Replacement of hinges, door/window shutter glass panes, wire gauge will be paid separately) complete all as specified and directed by Engineer in Charge

M&L for Attending complaints related to black smith work and obtaining completion from user including repair of steel frames of doors and windows, CGI roof sheets, steel rolling shutter by drilling/ welding, resecuring of door/ window etc complete all as specified and directed by Engineer in Charge

Providing & applying rising damp-proof costing system with single component ready to use damp- proof coating Roff Hydamp : 1. Surface preparation thoroughly brush and clean all laltance, loose particles such as dirt, grease, mortar droppings , release agents, efflorescence, bird droppings , etc. All large volds or hollow portions must be removed and re-plastered , Non - moving cracks having width upto 5 mm must be filled with polymer based brack filler. 2. APPLICATION : Apply the first coat of Dr fixit Damp guard Classic with a paint brush directly on the prepared surfaces by mixing (1 part base : 1 part hardner : 1 part of water). Allow to dry for a minimum 2-3 hrs . Apply on e part of DAMP GUARD mixed chemical and 2 parts of OPC whte cement / Birla putty and make the putty , apply putty on the entire surface area. Allow it to dry for at least 3-4 hours . Apply the Final coat of Dr Fixit Damp guard classic on the entire surface and allow the surface to air cure 48 hours proceeds for Paint

Taking up or down steel tubing and connections of any description and from any position incl cleaning for refixing or removing from site.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

S&F bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe 20mm bore (Minimum weight 210 gms) complete all as specified and directed by Engineer in Charge

S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe 15mm bore (Minimum weight 90 gms) complete all as specified and directed by Engineer in Charge

S&F in repair Pillar tap standard of PTMT any colour high pressure screwed for iron pipe 15mm bore (Minimum weight 110 gms) complete all as specified and directed by Engineer in Charge

S&F in repair Stop valve of PTMT any colour high pressure screwed for iron pipe 15mm bore (Minimum weight 90gms) complete all as specified and directed by Engineer in Charge

S&F in repair stop valve of PTMT any colour high pressure screwed for iron pipe 20mm bore (Minimum weight 112gms) complete all as specified and directed by Engineer in Charge

S&F in repair waste coupling of PTMT (half or full threaded) for discharge pipe of 32mm/40mm bore (Minimum weight 45gms) complete all as specified and directed by Engineer in Charge

S&F in repair PVC waste pipe for 32mm bore pipe complete complete all as specified and directed by Engineer in Charge

S&F in repair Grating doom 125 mm dia of PTMT (Minimum weight 25 gms) with wste hole/without waste hole complete all as specified and directed by Engineer in Charge

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer in Charge

S&F in repair PVC low level flushing cistern kit suitable for existing flushing cistern of any type complete all as specified and directed by Engineer in Charge

S&F in repair PVC valveless, syphonic action type, flushing cistern 10 lit capacity, low level, white, with inlet, ball valve, float and handle including flush pipe complete all as specified and directed by Engineer in Charge

S&F in repair Bib taps CP fancy type with butterfly handle screwed down high pressure for 15mm bore ISI marked complete all as specified and directed by Engineer in Charge

S&F in repair Pillar taps cast copper alloy quarter turn, fancy type CP screwed down high pressure for 15mm bore complete all as specified and directed by Engineer in Charge

S&F in repair stop/angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle for pipe of 15mm/20mm bore complete all as specified and directed by Engineer in Charge

S&F in repair hot and cold WHB mixer chromium plated quarter turn screwed down for pipe of 15mm bore complete all as specified and directed by Engineer in Charge

S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer in Charge

S&F in repair Rotational moulded polyethylene Water storage tanks (cylindrical vertical with closed top) 1000 litres capacity hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer in Charge

S&F in repair PVC lids for water storage tank of cap 500 Litres/1000 Litres complete all as specified and directed by Engineer in Charge

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

S&F in repairs shower rose 125 mm size of brass chromium plated fancy type with or without swivel joint suitable for fixing to 15mm bore GI pipe complete all as specified and directed.

S&F in repair CP towel rail 60 Cm long, complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack, 1 mm thick of size 900 mm x 780 mm x 222 mm fixed to wall with brass screws complete all as specified and directed.

Taking down waste / soil/PVC pipes any size any pattern inludings cleaning or refixing or removal to store complete all as specified and directed

S&F PVC(SWR) 110mm dia soil / waste and rainwater drainage pipes (5 kgf / sqcm) single socketed with bends in any length with rubber ring joint laid in floor or fixed on wall incl branch piece, bend, socket etc complete all as specified and directed

S&F PVC(SWR) 75 mm dia soil waste and rainwater drainage pipes (5 kgf / sqcm) single socketed with bends in any length with rubber ring joint laid in floor or fixed on wall incl branch piece, bend, socket etc complete all as specified and directed

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement of dia of outlet 75mm complete all as specified and directed

S&F in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers, waste coupling and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm all complete as specified and as directed.

S&F in repair PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as directed.

S&F in replacement of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples all as specified and directed by Engineer in Charge

S&F in repair Aluminium, anodised, barrel tower bolts of extruded section 200mm size complete all as specified and directed by Engineer in Charge

S&F in repair Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 250mm size complete all as specified and directed by Engineer in Charge

S&F in repair Aluminium handles, cast type, anodised 150mm size complete all as specified and directed by Engineer in Charge

S&F in repair Hasp and staple 100mm size, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer in Charge

S&F in repair floor door stopper 150mm size of Aluminium body and tongue, anodised, with double leg complete all as specified and directed by Engineer in Charge

S&F in repair sheet glass ordinary quality 4mm thick and glazing with oil putty in squares not exceeding 0.50 Sqm complete all as specified and directed by Engineer in Charge

S&F in repair figured glass, pinhead type ordinary quality 4mm thick and glazing with oil putty in squares not exceeding 0.50 Sqm complete all as specified and directed by Engineer in Charge

S&F in repair sheet glass Tinted quality 4.8 mm thick and glazing with rubber/ aluminium beading for Aluminium window/ventilator etc,complete all as specified and directed by Engineer in Charge

S&F in repair for 25 MM SS Curtain Rod with fixing brackets and Knob complete all as specified and as directed.

S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white with integral foot rests and connection with cast iron P trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern and flush pipe) complete with provision of lime concrete bedding including taking down/ Dismantling existing unserviceable WC of any description and in any position & fixing new WC in repair and making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.

S & F in repair vitreous china wash basin, white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F in repairs viterous china wash down water closet (Pedestal pattern) EWC white incl plastic water closet seat cover and mild steels chromium plated on aluminium hinging device and connecting to 'P' or 'S' incl connecting flush pipe with flushing rim all as specified

S&F in repair 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws/nails to timber frame work as in cupbord door/shelves complete all as specified and directed

S&F in repair 18 mm (+0.7mm) thick solid PVC Sheet one side prelam for cupboard shutter of density 600 Kg/Cbm bent 900 and finish at all edges at level for makingedges at level for making edge lipping/bendingor 0.5 mm thick PVC sheet lipping at 4 edges using bonding taps etc complete all as per direction of Engr-in-charge and manufacturer specification.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed

Taking down shutter of any description but exc 1 sqm and n. exc. 2 sqm each complete all as specified

S&F solid PVC door frame of size 50mmX47mm made out of 5mm both side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening all as per specifications and drawing shown on sl page No 150 of SSR part II

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & both side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of both side prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required & directed by the Engr-in-Charge.

S&F for stainless steel butt hinges 100mm size medium weight complete all as specified and directed.

S&F in repair 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed.

S&F mild steel angle Iron work as in doors or Gate or grill of angle of other section with gueset plates , rails brackets etc, complete, drilled for fixing of steel sheeting or other covering, Doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging dooe fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete FE 290 (Gde-E-165)

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F 2nd hard wood 35mm thick glazed, and skeleton shutters open rebated & prepared to receive, glass, gauge etc. divided into squares with plain chamfered or rounded mitred and rebated any numbers and size of members of shutters as specifed in SSR Part I, Section 8, clause 8.24(a); supllied and fitted to chowkahts complete all as specified and directed.

S & F 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F for 150 mm size aluminium anodised door handles complete all as specified and directed

S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp and stapple ( bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

Preparation of new or previously untreated wooden surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of pink primer complete all as specified.

S&F aluminium powder coated framed windows, any pattern, fixed/side hung/sliding Three Track using powder coated aluminium sections or approved make, with or without sas bar, suitable for 4.00 mm thick glazing and stainless steel alloy wire cloth, 0.36mm nominal dia of wire and averadge width of oaperature 1.40 mm wire gauze, includingnecessary rubber packing, joining cleats, glazing clips, aluminium snap beading, handles, locking arrangments, frame of window should be of handles locking arrangment, frame of window should be of 1.5 mm thick section & shutter sec like handle/interlocking/top/bottom should be of 1.2 mm thick etc, complete all as specified and as directed. Note : Rates inclide all glazing/aluminium wire cloth, rubber packing, joining cleat glazing clips, aluminium snap beading, locking arrangments handle etc.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl and over screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed. complete all as specified and directed

S/F coloured plain/printed glazed tiles of size 450 x 300 x 7 mm, on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick rendering in CM 1:4

M & L for Joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl and over screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed. complete all as specified and directed

M & L for 18-20 mm thick granite slab (Red/black) work (table rubbed and polished) in steps, Jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 20 mm thick cement plaster (1:3).(All exposed surfaces should be bull nosed)

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed

M&L for 10 mm thick rendering on surfaces other than fair faces of brick/concrete surfaces in CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L 2mm thick wall care putty on wall including complete removal of existing treatment all as specified and directed by Engr-in-charge

M&L for preparation of the newly plastered surfaces of walls & applying two coats distemper oil- emulsion , white or tinted over a coat of primer surfaces of wall complete all as specified and directed.

Dismantling wall and ceiling boards any description, any thickness, including cover fillets complete all as specified and directed

S&F Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board (Everest)/Asbestos Cement white fiber Board 4mm thick of size 595 x 595 mm fixing with screws/clips complete all as per manufacturers instructions and direction.

nevi constructions (BID ID -3366083)

VIJAY CONSTRUCTION CO (BID ID -3379777)