Renovation of Sub Divisional Officer Residence at Canal Colony Naraingarh

Amount

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismentling doors windows and clerestory windows (Steel or Wood) shuttering including Chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below.

Demolishing mud phaska in terracing and disposal of material within 50 metres lead.

Demolishing cement concrete manually /by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-Charge Nominal concrete 1:2:4 or leaner mix(i/c equivalent cum design mix)

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge in cement mortar.

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand (zone-III) 4 graded stone aggregate 12.5 mm nominal size.)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth leavel upto floor IV level in all shapes and sizes in cement mortar 1:4 (1 cement:4 coarse sand)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement:4 coarse sand)

10 mm thick cement plaster 1:2 (1 cement:2 fine sand)on ceiling

12 mm cement plaster of mix 1:2 (1 cement:2 fine sand)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge fixing with adjustable lugs with split end tail to each jamb

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately} Second class teak wood 35 mm thick shutter

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: Kiln seasoned and chemically treated Hollock wood

Providing & laying average 6mm thick POP Coating on walls, Ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-InCharge

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low voe (Volatile Organic Compound ) content with water thinnable cement primer on wall surface having voc content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, having voc (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour with two coats

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete.

Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc.

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. Size of tiles 600x600mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. Size of tiles 600x600 mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc.

TMT bars of grade FE-500D of Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level.

Providing and fixing aluminium sliding door bolts for door and window, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. (250x16 mm)

Providing and fixing aluminium tower bolts, ISI marked, 19 nodized (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. (250x10 mm)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. (125 mm)

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. (Twin Rubber stopper)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level 1:3:6 (1 Cement : 3 coarse sand (zone-Ill) : 6 graded cum stone aggregate 20 mm nominal size)

Providing and laying of precast terrazzo tiles 20 to 22 mm thick with graded marble chips of sizes up to 12 mm, in skirting and risers of steps not exceeding 30 cm in height, on 12 mm thick cement plaster 1 :3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of Medium shades pigment using 50% white cement and 50% ordinary cement.

Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase.

Providing and fixing HDPE water storage tank of Sintex, Diplast, OK Supreme make with covers/lids marked with IS:12701 on roof top of building including cost of hoisting and placing in position making connections with inlet and outlet pipes, providing overflow and store provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connection, 1000 litres (NS)

Providing and fixing pressed clay tile (Mangalore tiles) of size 200mm x 125mm x 10mm on slopping roof top/ window projections with 12mm thick cement, coarse sand mortar 1 :3 including cost of ridge wherever required as per approved design complete in all respect up to 4 storey or 15 Meter Height.

Providing and fixing of marble stone flooring with 16 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with Makrana white second quality.

Extra for pre finished nosing to treads of steps of marble stone.

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /Wooden frames with rawl plugs screws etc.

Providing and laying 60 mm thick ISI marked interlocking paver blocks of all shapes and colours in design mix over a bed of 30 mm thick fine sand complete in all respect

Supply and erection of PVC conduit pipe 25 mm dia

Supply and erection of PVC conduit pipe 20 mm dia

COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT Wiring for Fan/Light/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe: Group A (havells)

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required: Group A. (havells)

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box, modular face plate etc complete as required: Group A. (havells)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 1 &2 Modules including combined plate for Telephone and data.

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 3 Modules HSR (23.8.10.2)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 4 Modules HSR (23.8.10.3)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 6 Modules HSR (23.8.10.4)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 8 Modules HSR (23.8.10.5)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (havells) 12 Modules HSR (23.8.10.6)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) 5 amp 1 way switch HSR (23.8.11.1)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) 5 amp 2 way switch

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) 15 amp 1 way switch

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) 5 amp Socket

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) 15 amp 6 pin Socket

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) Bell Push

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) step type Fan Regulator 2 modules 300 watt

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) TV Socket outlet modular type

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (havells) Blanking plate

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections: 6 amp. To 32 amp Double POLE.

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections: 40 amp to 63 amp. Double pole.

Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required

Extra for using salt and char coal/coke for pipe earth electrode as required

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White vitreous chinaware Wash basin size 550x400 mm with a15 mm CP Brass single hole basin mixer

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge) (Jaguar): Two way

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter (Jaguar)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.: 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.: 15 mm nominal bore(Jaguar)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (Jaguar)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing in position best Indian make C.P. brass Tooth Brush cum Tooth Paste Holder fixed in with rawl plugs with C.P. brass screws complete including cutting and making good the walls etc. Tooth Brush-cum-Tooth Paste holder

Providing and fixing jet (H) with connection pipe.(NS)

Providing and fixing PVC waste pipe (H).(NS)

Providing and fixing PVC Rain Water Pipe 6 kg pressure of ISI mark (NS)

Providing PVC Rain Water Pipe 3” dia (NS)

Providing and fixing PVC bend ISI Mark 100 mm dia(NS)

Providing Tee 4” dia Finolex (NS)

Providing Elbow 8” dia Finolex (NS)

Providing Tee 3” dia Finolex (NS)

Providing P Trap 4” dia(NS)

Providing Floor trap 3” dia Finolex PVC(NS)

Providing Socket 3” dia Finolex PVC(NS)

Providing Socket 4” dia Finolex PVC (NS)

Providing and fixing floor mounted, white vitreous chinaware single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous chinaware cistern of capacity 1 O litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Supply of Jindal G.I Pipe ½” (B Class) (N.S.)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials: (i) 15 mm internal diametre of pipeline

Supply of Jindal G.I Pipe ¾” (B Class) (NS)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials: (ii) 20 mm internal diametre of pipeline

Supply of Jindal G.I Pipe 1” (B Class) (NS)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials: (iii) 25 mm internal diametre of pipeline

Supply of fixing of Brass Valve 1” dia Unik of Jalota mark (NS)

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Credit of dismantled old brick work

Credit of dismantled tile masonary

Credit of dismantled steel

Credit of wood work

The Anjana Coop Society

Kuldeep Construction Company